JVC LYT2232-002A User's Manual
Contents
1. f you cannot avoid opening the marine case at the diving location pay attention not to let water droplets from your hair or your body enter the case Remove the O ring and wipe off salt sand and other foreign matter Also wipe the groove in which the O ring was inserted and the part of the marine case that was in contact with the O ring and allow them to dry For details on handling and storing the O ring refer to the O ring Maintenance Manual Dirt sand salt crystals etc Qa 7 Wipe the inside and outside of the marine case with a dry cloth Use a lint free cloth to wipe the inside of the marine case Wipe the inner side of the front glass Add a few drops of the cleaner liquid commercially available onto the inner side of the front glass and wipe off using a lens tissue paper clean cloth etc Specifications The front glass will fog if it is dirty Maximum Water depth up to 40 meters Let it dry completely in a shaded area Operations Power on off Video recording start stop Do not leave the marine case in direct sunlight Still image shooting Doing so may cause discoloration of the case and may cause the O ring to deteriorate more Zoom tele wide quickly Filter diameter 67 mm Main unit 216 mm x 179 mm x 128 mm dimensions The conditions may vary depending on the WxDxH environment of use such as temperat2. the O ring is twisted if you forget to attach or 3rd time minutes 5 minutes try operating if something is trapped in the seal the levers and buttons while the marine case is submerged Check that all the operation buttons of the camera are functioning properly If itis not functioning take out the camera Always have someone hold the marine case and insert again for you when diving into or getting out of A hth water to prevent loss or damages Attach the grips if for any reason water leakage occurs remove Attach the grips lights or weights on the the camera battery It may cause the camera to bottom of the marine case explode Turn on the camera s power Press and hold the power button for more than 2 seconds to turn on the power The camera s power lamp lights and the monitor turns on ON OFF 2 Large hexagonal wrench for screwing the grips Sometimes due to sudden shaking or impact to the marine case the camera s drop detection function operates to turn off the camera s power When the camera s power is turned off turn it on again 18 Press the video recording start stop button or the still image lever to start recording Zooming Tele Zooming Wide Still image lever Shoot still images Video recording start stop button Start stop the video recording When you ha
3. the marine case JVC cannot accept responsibility for any damage that may occur to the internal equipment and materials video camera SD card etc or any expenses incurred in taking the photographs video Therefore please be careful when using the marine case Safety Precaution Before use this unit must be pre tested to check if there is any water Please read before use leakage This marine case is a precision instrument designed to permit safe video recording under high water pressure Please pay careful attention when handling the unit before and after use as explained in this user s manual Each part of the marine case has been subject to strict controls during the manufacturing process and the individual functions have faced stringent tests during the assembly process Each marine case has also had to pass waterproof inspections using high pressure water testers However damage can sometimes occur during transport and distribution or during storage after purchase so before diving always carry out the following pre use test to verify safety Pre use test Be sure to perform the following pre use test before diving 1 Before mounting the camera inside the marine case dive with only the empty marine case and test for water leaks Allow 5 or 6 minutes to ensure there are no leaks Be sure to perform this test to ensure the safety of your camera 2 The following are some common causes of water leaks
4. A The marine case is used without attaching the O ring B The O ring is not mounted in the correct position C The O ring is damaged or deformed D There is sand dirt hair or other foreign matter on the O ring E There is sand dirt hair or other foreign matter on the contact surface of the O ring or on the inside of the lid F The provided strap or drying agent bag is pinched inside the marine case when the lid is closed 3 Check that there no scratches or cracks on the marine case every time you use it Accessories The marine case must withstand water Anti fog liquid pressure with use Repeated exposure to e Silicone grease 5 g x 1 pressure eventually leads to material fatigue Sili ioth which may result in damage of the marine NCONE CIO case Every time you use the marine case e Drying agent 2 9 x 5 check in advance that there are no scratches e Strap or cracks If you frequently use the marine 2 O rings case be sure to ask for maintenance at the One spare O ring store of purchase There is a charge for maintenance To protect your camera and ensure optimum use keep the examples listed above in mind when using the marine case Base To attach to the camera JVC accepts no responsibility for water leakage or damage to anything inside the marine case Grip camera SD card etc due to careless usage of Commercially available this product Be sure to follow cor
5. container and shake the marine case in the upward downward left and right directions Move the buttons and levers while the marine case is submerged and rinse the dirt out from any gaps or grooves Proceed to f used in the sea gt Proceed to 011011 Performing salt removal If the marine case was used in the sea submerge the marine case in fresh water for at least 1 hour to remove salt 1 Prepare a container that contains fresh water that is five times more than the volume of the marine case The container must be big enough to allow the marine case to submerge fully if only small containers are available pour in fresh water that is equivalent to at least five times the volume of the marine case over a few times Shaking the marine case in the upward downward left and right directions will be more effective Move the buttons and levers while the marine case is submerged and rinse the salt out from any gaps or grooves etc Make sure the grip is also free of salt Put in fresh water for at least 1 hour Remove the marine case and wipe off water droplets on the case surface using a dry towel Remove the camera Face the front glass of the marine case upwards and open the buckles to remove the camera while paying attention not to let water droplets at O ring or buckles enter the case The camera may fall out if the buckles are opened with the front glass facing down
6. not pull too strongly This will cause deformation About 1 cm Grease Check for any foreign matter in the O ring groove Inspect thoroughly as it is usually not visible Grains of sand and crystallize salt may be stuck inside Remove them carefully by either using an air spray or a swab Make sure the fibers of the swab are not adhered Groove Insert the O ring after inspection Make sure no foreign matter is adhered when placing the greased O ring back to the groove Do not pull too strongly and make sure the O ring is placed evenly and not twisted lt POINT gt Insert from the four diagonal corners and smooth out evenly Storing the O ring If you do not intend to use the marine case for a long period of time remove the O ring and allow it to rest 1 Remove the O ring Be sure to use the pick supplied 2 Wipe off the grease gently 3 Check for any foreign matter that might be adhered to it 4 Put the O ring inside a clean plastic bag and store in a way that it will not be subject to stress Do not put in moth balls and other insect repellents Do not leave the O ring as is in the marine case for a long period of time It may deform due to heat and pressure resulting from the locked and tightened state Do not store in hot and humid locations This will cause the O ring to deteriorate more quickly LYT2232 002A JVC H ENGLISH DE
7. JVC WR MG270 ZUJT A EVENE Marine Case INSTRUCTIONS Unterwassergeh use BEDIENUNGSANLEITUNG Bo tier sous marin MANUEL D UTILISATION Onderwaterhuis GEBRUIKSAANWIJZING Carcasa submarina MANUAL DE INSTRUCCIONES Custodia subacquea ISTRUZIONI Obudowa podwodna INSTRUKCJA OBSLUGI KE EHRE Ay 4 ola Leste LYT2232 001A HH I ENGLISH DEUTSCH FRANCAIS NEDERLANDS CASTE ESP ITALIANO POLSKI AM SARS 12 In order to use this product safely Preparation c Pg 16 e Check that there is no dirt cracks or damage to the O ring e Always apply grease to the O ring Attaching the Marine Case the Camera c Pg 17 18 e Attach the power button cap depending on the camera used Make sure that the O ring is not twisted and that you do not forget to attach it e When tightening the seal make sure there are no foreign objects caught in the seal Recording the Video Still Image Files c Pg 18 19 e Avoid opening and closing the marine case in the shooting location e When holding the marine case lower it gently into the water Detaching the Marine Case Maintenance c Pg 19 20 21 Always wash the marine case in fresh water after use e Perform maintenance on the O ring If water leaks into the case due to careless use of
8. UTSCH FRAN AIS NEDERLANDS CASTE ESP ITALIANO POLSKI DENE T OUYVAICIWT O ring Maintenance Manual O Ring Wartungshandbuch Manuel d entretien du joint d etancheite Onderhoudshandleiding voor de O ring Manual de mantenimiento de la junta torica Manuale di manutenzione dell anello circolare NO Instrukcja konserwacji pier cienia uszczelniajgcego 44 ial 4 ilaa huts
9. agent be replaced each time Silicone cloth Wash the marine case with fresh water and wipe the outer side of the whole case with the silicone cloth after drying Hexagonal wrench small Buckle opener For use when you have difficulty opening the buckle Hook the wrench to the buckle and pull towards Grip belt of camera I gt Screw tightening key Use the key to tighten the screw of the base 15 Bottom view 1 Main casing grip Attach the strap provided as shown in the diagram above 2 Zoom lever Zoom tele wide while shooting 3 Ring Commercially available filters 67 mm diameter can be attached 4 Buckle 3 locations Seal the marine case 5 Grip attachment holes You can attach the grip provided or commercially available weights 6 Still image lever Press to take still images 7 Video recording start stop button Press once to start recording a video Press again to stop 8 Power button Turns camera s power on off 16 Inspect the main casing for scratches and cracks Apply 2 or 3 drops of the anti fog liquid provided onto a lens tissue paper commercially available or a clean cloth and wipe the inner side of the marine case front glass Check the O ring Using the pick provided remove the O ring from the main case Che
10. ck the O ring O ring contact surface and groove in which the O ring fits for foreign matter nicks cracks etc Be sure to remove any foreign matter dirt sand salt crystals hair lint etc For details refer to the O ring Maintenance Manual Never use the O ring in case of nicks and cracks f the O ring is handled inappropriately it can cause water leakage Apply grease to the O ring re attach Close the empty marine case no camera inside Submerge the marine case in water and check that there are no water leaks c Pg 18 Fold the grip belt Attaching the Marine Case to the Make sure the grip belt is not caught Camera between the marine case when sealing Setup the camera Open the marine case For models equipped with light turn off the If it is difficult to open buckles use the light small hexagonal wrench buckle opener Open the lens cover Set to the shooting mode video still image Even when the shooting mode is set to video still images can be captured by pressing the still image lever during video recording is recommended to set to the auto Small hexagonal wrench shooting mode Buckle opener Insert the battery and the microSD microSDHC card or SD SDHC card Attach the power button cap beforehand if meadad Not required for GZ HM545 to GZ HM570 To turn off the camera press and hold the Fi
11. dleiding voor de O ring Manual de mantenimiento de la junta torica Manuale di manutenzione dell anello circolare NO Instrukcja konserwacji pier cienia uszczelniajgcego plat hula AAs ENGLISH DEUTSCH FRAN AIS NEDERLANDS CASTE ESP ITALIANO POLSKI 24 18 3 What is O ring O ring is a type of seal used to make underwater cameras strobes and other diving instruments waterproof It looks like a big thick rubber band The O ring is an important component that protects the camera from water by keeping the marine case airtight When should the O ring be inspected As a general rule each time before using Salt crystals are formed when seawater that entered the O ring groove dries Salt crystals just like sand can cause water leakage When shooting on the sandy seabed or when the camera is placed on the sand When not used for a long period of time Inspection and maintenance of the O ring Remove the O ring To inspect the O ring use the pick supplied to remove it from the O ring groove Do not use knifes scissors tweezers and other sharp objects which might damage the O ring and the O ring groove Check for hair dirt sand salt dust and other foreign matter Ev
12. en small foreign matter can cause water leakage Check for foreign matter that are not visible by rubbing gently with your fingers Be sure to remove all foreign matter Adair ADust ASalt ALint Wipe off any residual grease Wipe off gently with a soft cloth or tissue paper After wiping make sure the fiber of the cloth or tissue paper is not adhered to the O ring Check for any deforms distorted crushed cracks or cuts on the surface Cracks on the O ring can be easily spotted by bending and Cracks twisting it gently Never use an O ring if it is deformed cracked damaged in any way It can cause water leakage Replace the O ring with a brand new one every year Even if there are no nicks cracks etc its effectiveness will deteriorate due to wear f 2 ACracks ADistortion ACrushed AFrayed ANicks corrosion Apply silicone grease on the O ring The O ring needs to be re greased when its surface appears dry Be sure to remove the O ring and apply the silicone grease on it 7 Squeeze about 1 cm onto your finger 2 Apply it on the O ring by holding the O ring with your fingers If the amount applied is not enough repeat the above step Make sure that you do not apply too much grease Dirt and dust will easily adhere if too much grease is applied Neither will it improve the waterproofing Be sure to apply moderately Do
13. rect procedures lights and weights can also when using the marine case be attached When there is a need for buoyancy adjustment attach commercially available weights to the grip e Pick F e Screw tightening key G e 2 hexagonal wrenches Large for screwing the grip Small buckle opener e Power button cap Maintenance Kit Sold Separately Part Number MG270_MTKIT You can purchase the following set of expendable parts Please contact your local JVC service representative e O rings x 2 e Silicone grease 5 g x 1 e Drying agent 2 g x 5 e Lens tissue paper 50 sheets x 1 e Power button cap x 2 13 Procedures for Using the Supplied Maintenance Kit Pass the strap through the strap attachment hole before using the marine case to maintain a firm grip in water Anti fog liquid Apply the anti fog liquid on the inner side of front glass before using the marine case Add two to three drops of the liquid on a lens tissue paper commercially available or a clean cloth and apply on the inner side of the front glass Front glass Marine case Drying agent Prevents fogging inside the marine case 22 Insert it at the back of the base attached to the camera SS 2 The moisture absorption ability of drying SS agent that has previously been used may deteriorate depending on the conditions of use As such we recommend that the drying
14. t the hollow of the power button cap to power button for more than 2 seconds the protrusion of the power button on the case Insert the drying agent at the back of the base Catch i SAR Drying agent Pass underneath Q Insert the camera into the marine case Align the base attachment groove with the Attach the base to the bottom of the base to insert camera Align the tripod screw hole at the bottom of your camera with the screw of the base and tighten the screw 2 Tighten the screw Base attachment groove Base i Marine case internal base O Adjust the angle of the LCD monitor The LCD monitor can be tilt upwards to a i maximum angle of 30 degrees The camera turns on automatically when the WE LCD monitor is opened To turn off the camera press and hold the power button for more than LOIS 2 seconds LT i 17 Seal the marine case Make sure that the O ring is not twisted and that you did not forget to attach it Make sure that foreign objects strap belt dirt etc have not been caught in between Recording the Video Still Image Files Before recording Submerge the marine case with the camera inserted into a bathtub or water tank full of fresh water Gradually prolong the time the marine case is submerged as follows ist time 5 10 seconds The risk of water leakage is extremely high if 2nd time 30 seconds 1 minute
15. ure l humidity water temperature salinity and Main unit weight Approx 890 g others excluding grip Storing the O ring Applicable camera models From GZ HM300 to GZ HM350 If you do not intend to use the marine case for From GZ HM545 to GZ HM570 longer than one month remove and store the O ring away From GZ HD500 to GZ HD620 For details refer to the O ring Maintenance Manual AN The O ring is an expendable part Replace the O ring with a brand new one every year When re using an O ring after storage always check the condition of the O ring Never use an O ring if it is deformed crushed distorted cracked or damaged in any way 21 LYT2232 001A ENGLISH DEUTSCH FRANCAIS NEDERLANDS CASTE ESP ITALIANO POLSKI H lt xq or Dt WR MG270 VUYT AZ INSTRUCTIONS Unterwassergehause BEDIENUNGSANLEITUNG Boitier sous marin MANUEL D UTILISATION Onderwaterhuis GEBRUIKSAANWIJZING Carcasa submarina MANUAL DE INSTRUCCIONES Custodia subacquea ISTRUZIONI Obudowa podwodna INSTRUKCJA OBSLUGI KE 8 Ay paral 4 ola Leste JVC OV YAlcDUT LYT2232 002A O ring Maintenance Manual O Ring Wartungshandbuch Manuel d entretien du joint d etancheite Onderhoudshan
16. ve finished recording press and hold the power button for more than 2 seconds to turn off the camera The camera s power lamp goes out and the monitor turns off Detaching the camera If there is a need to detach immediately Submerge the marine case in fresh water and shake the marine case in the upward downward left and right directions for at least 10 times followed by rinsing it Remove the marine case and wipe off water droplets on the case surface using a dry towel Face the front glass of the marine case upwards and open the buckles to remove the camera while paying attention not to let water droplets at O ring or buckles enter the case Upon removing the camera close the marine case again while paying attention not to allow water droplets enter the case followed by tightening all the buckles Always perform maintenance on the marine case after using t Pg 20 If there is no need to detach immediately Perform maintenance on the marine case c Pg 20 19 20 Maintenance on the marine case Always perform maintenance on the marine case after you have finished recording Salt crystal or dirt will accumulate inside the marine case if maintenance is not performed and this can cause water leakage Wash the marine case in water while it is still sealed Do this within 30 minutes after diving Pour in fresh water until the marine case is completely submerged in the
Download Pdf Manuals
Related Search