JVC LYT2112-003A User's Manual
Contents
1. POLSKI MERE F dal 9 What is O ring O ring is a type of seal used to make underwater cameras strobes and other diving instruments waterproof It looks like a big thick rubber band e The O ring is an important component that protects the camera from water by keeping the marine case airtight When should the O ring be inspected e As a general rule each time before using Salt crystals are formed when seawater that entered the O ring groove dries Salt crystals just like sand can cause water leakage When shooting on the sandy seabed or when the camera is placed on the sand When not used for a long period of time Inspection and maintenance of the O ring e Remove the O ring To inspect the O ring use the pick supplied to remove it from the O ring groove Do not use knifes scissors tweezers and other sharp objects which might damage the O ring and the O ring groove Le ei Check for hair dirt sand salt dust and other foreign matter Even small foreign matter can cause water leakage e Check for foreign matter that are not visible by rubbing gently with your fingers Be sure to remove all foreign matter ADirt Adair C 22 ADust ASalt ALint2. Do this within 30 minutes after diving Pour in fresh water until the marine case is completely submerged in the container and shake the marine case in the upward downward left and right directions Move the buttons and levers while the marine case is submerged and rinse the dirt out from any gaps or grooves Proceed to f used in the sea gt Proceed to 0900112110971 Performing salt removal If the marine case was used in the sea submerge the marine case in fresh water for at least 1 hour to remove salt Prepare a container that contains fresh water that is five times more than the volume of the marine case The container must be big enough to allow the marine case to submerge fully f only small containers are available pour in fresh water that is equivalent to at least five times the volume of the marine case over a few times Shaking the marine case in the upward downward left and right directions will be more effective Move the buttons and levers while the marine case is submerged and rinse the salt out from any gaps or grooves etc Make sure the grip is also free of salt 2 Put in fresh water for at least 1 hour Remove the marine case and wipe off water droplets on the case surface using a dry towel Remove the camera Face the front glass of the marine case upwards and open the buckles to remove the camera while paying attention not to let water droplets at O ri
3. Wipe off any residual grease Wipe off gently with a soft cloth or tissue paper After wiping make sure the fiber of the cloth or tissue paper is not adhered to the O ring e Check for any deforms distorted crushed cracks or cuts on the surface Cracks on the O ring can be easily spotted by bending and Cracks twisting it gently Never use an O ring if it is deformed cracked or damaged in any way It can cause water leakage Replace the O ring with a brand new one every year Even if there are no nicks cracks etc its effectiveness will deteriorate due to wear f ce ACracks ADistortion ACrushed AFrayed ANicks ASand corrosion e Apply silicone grease on the O ring The O ring needs to be re greased when its surface appears dry Be sure to remove the O ring and apply the silicone grease on it Squeeze about 1 cm onto your finger Apply it on the O ring by holding the O ring with your fingers If the amount applied is not enough repeat the above step Make sure that you do not apply too much grease Dirt and dust will easily adhere if too much grease is applied Neither will it improve the waterproofing Be sure to apply moderately Do not pull too strongly This will cause deformation About 1 O ring d Grease e Check for any foreign matter in the O ring groove Inspect thoroughly as it is usually not visible Grains of s
4. Hook the wrench to the buckle and pull towards you Base Grip belt of camera Screw tightening key Use the key to tighten the screw of the base Bottom view 1 Main casing grip Attach the strap provided as shown in the diagram above 2 Zoom lever Zoom tele wide while shooting 3 Ring Commercially available filters 67 mm diameter can be attached 4 Buckle 3 locations Seal the marine case 5 Grip attachment holes You can attach the grip provided or commercially available weights 6 Still image lever Press to take still images 7 Video recording start stop button Press once to start recording a video Press again to stop 8 Power button Turns camera s power on off o Inspect the main casing for scratches and cracks Apply 2 or 3 drops of the anti fog liquid provided onto a lens tissue paper commercially available or a clean cloth and wipe the inner side of the marine case front glass Check the O ring Using the pick provided remove the O ring from the main case Check the O ring O ring contact surface and groove in which the O ring fits for foreign matter nicks cracks etc Be sure to remove any foreign matter dirt sand salt crystals hair lint etc For details refer to the O ring Maintenance Manual Never use the O ring in case of nicks and cracks Ifthe O ring is handled inappropriatel
5. position C The O ring is damaged or deformed D There is sand dirt hair or other foreign matter on the O ring E There is sand dirt hair or other foreign matter on the contact surface of the O ring or on the inside of the lid F The provided strap or drying agent bag is pinched inside the marine case when the lid is closed 3 Check that there are no scratches or cracks on the marine case every time you use it The marine case must withstand water pressure with use Repeated exposure to pressure eventually leads to material fatigue which may result in damage of the marine case Every time you use the marine case check in advance that there are no scratches or cracks If you frequently use the marine case be sure to ask for maintenance at the store of purchase There is a charge for maintenance To protect your camera and ensure optimum use keep the examples listed above in mind when using the marine case JVC accepts no responsibility for water leakage or damage to anything inside the marine case camera SD card etc due to careless usage of this product Be sure to follow correct procedures when using the marine case Accessories e Anti fog liquid e Silicone grease 5 g x 1 Silicone cloth Drying agent 2 g x 5 e Strap 2 O rings One spare O ring O ring Base To attach to the camera Grip Commercially available lights and weights can also be attached e Pick
6. JVC WR MG250 Marine Case INSTRUCTIONS Unterwassergehause BEDIENUNGSANLEITUNG Boitier sous marin MANUEL D UTILISATION Onderwaterhuis GEBRUIKSAANWIJZING Carcasa submarina MANUAL DE INSTRUCCIONES Custodia subacquea ISTRUZIONI Obudowa podwodna INSTRUKCJA OBS UGI KE 9195 LYT2112 001A ENGLISH DEUTSCH FRAN AIS NEDERLANDS CASTE ESP ITALIANO POLSKI ID S 9 In order to use this product safely Preparation c Pg 6 Check that there is no dirt cracks or damage to the O ring Always apply grease to the O ring A Attaching the Marine Case to the Camera c Pg 7 8 Make sure that the O ring is not twisted and that you do not forget to attach it When tightening the seal make sure there are no foreign objects caught in the seal A Recording the Video Still Image Files Pg 8 9 Avoid opening and closing the marine case in the shooting location When holding the marine case lower it gently into the water Detaching the Marine Case Maintenance c Pg 9 10 11 Always wash the marine case in fresh water after use Perform maintenance on the O ring If water leaks into the case due to careless use of the marine case JVC cannot accept responsibility for any damage that may occur to the internal equipment and
7. Screw tightening key 2 hexagonal wrenches Large for screwing the grip Small buckle opener Maintenance Kit Sold Separately Part Number MG100_MTKIT You can purchase the following set of expendable parts Please contact your local JVC service representative e O rings x 2 e Silicone grease 5 g x 1 Drying agent 2 9 x 5 Lens tissue paper 50 sheets x 1 Procedures for Using the Supplied Maintenance Kit Pass the strap through the strap attachment hole before using the marine case to maintain a firm grip in water Front glass Ee Anti fog liquid Apply the anti fog liquid on the inner side of front glass before using the marine case A Add two to three drops of the H liquid on a lens tissue paper commercially available or a clean cloth and apply on the inner side of the front glass Marine case Drying agent Prevents fogging inside the marine case Insert it at the back of the base attached to the camera The moisture absorption ability of drying agent that has previously been used may deteriorate depending on the conditions of use As such we recommend that the drying agent be replaced each time Silicone cloth Wash the marine case with fresh water and wipe the outer side of the whole case with the silicone cloth after drying Hexagonal wrench small Buckle opener For use when you have difficulty opening the buckle
8. an O ring after storage always check the condition of the O ring Never use an O ring if it is deformed crushed distorted cracked or damaged in any way Specifications Maximum Water depth up to 40 meters pressure Operations Power on off Video recording start stop Still image shooting Zoom tele wide Buoyancy 440 g with the camera GZ HD300 320 inserted and the supplied battery pack attached 460 g with the camera GZ MG840 880 inserted and the supplied battery pack attached Filter diameter 67 mm Main unit 216 mm x 179 mm x 128 mm dimensions WxDxH Main unit weight Approx 850 g excluding grip Applicable camera models GZ HD300 GZ MG840 GZ HD320 GZ MG880 11 LYT2112 001A JVC WR MG250 Marine Case INSTRUCTIONS Unterwassergehause BEDIENUNGSANLEITUNG Boitier sous marin MANUEL D UTILISATION Onderwaterhuis GEBRUIKSAANWIJZING Carcasa submarina MANUAL DE INSTRUCCIONES Custodia subacquea ISTRUZIONI Obudowa podwodna INSTRUKCJA OBS UGI KS EHRE JVC LYT2112 002A Instrukcja konserwacji pier cienia uszczelniajacego O ring Maintenance Manual O Ring Wartungshandbuch Manuel d entretien du joint d tanch it Onderhoudshandleiding voor de O ring Manual de mantenimiento de la junta torica Manuale di manutenzione dell anello circolare
9. and and crystallize salt may be stuck inside Remove them carefully by either using an air spray or a swab Make sure the fibers of the swab are not adhered Groove Insert the O ring after inspection Make sure no foreign matter is adhered when placing the greased O ring back to the groove Do not pull too strongly and make sure the O ring is placed evenly and not twisted lt POINT gt Insert from the four diagonal corners and smooth out evenly Storing the O ring If you do not intend to use the marine case for a long period of time remove the O ring and allow it to rest Remove the O ring Be sure to use the pick supplied Wipe off the grease gently Check for any foreign matter that might be adhered to it Put the O ring inside a clean plastic bag and store in a way that it will not be subject to stress Do not put in moth balls and other insect repellents Do not leave the O ring as is in the marine case for a long period of time It may deform due to heat and pressure resulting from the locked and tightened state Do not store in hot and humid locations This will cause the O ring to deteriorate more quickly LYT2112 002A JVC ENGLISH DEUTSCH FRAN AIS NEDERLANDS CASTE ESP ITALIANO POLSKI AXES d O ring Maintenance Manual O Ring Wartungshandbuch Manuel d entretien du joint d tanch it Onderhoudshandleiding vo
10. atie met een lage temperatuur en een laag vochtigheidsniveau 3 Temperatuurverschillen tijdens opnamen maken Als men onmiddellijk voordat men onder water opnamen neemt de camera onder een hoge temperatuur laat liggen zoals onder de hete zon op de boot kan het glas beslaan door het grote temperatuurverschil Minimaliseer het temperatuurverschil zo veel mogelijk voordat u onder water opnamen maakt 4 Drastische veranderingen in waterdruk Als u plotseling in diep water duikt kan de drastische verandering in waterdruk tot gevolg hebben dat het glas beslaat Het verdient aanbeveling dat geleidelijk het diepe water in gaat tijdens het duiken ESPANOL CASTELLANO Como prevenir el empanhamiento del cristal delantero durante el disparo submarino Efectuar disparos submarinos en las condiciones que se establecen a continuaci n podria provocar el empafhamiento del cristal delantero y de este modo afectar la calidad de las imagenes capturadas Tenga en cuenta las siguientes precauciones durante la utilizaci n 1 Humedad dentro de la carcasa submarina Una peque a cantidad de humedad dentro de la carcasa submarina podr a provocar un empa amiento durante el disparo submarino Cerci rese de que el interior de la carcasa submarina est completamente seco antes de utilizarla Evite el ingreso de agua a la carcasa al abrir cerrar la carcasa submarina o cuando instale la c mara En especial no instale la c mara si la ha tocado con las manos h meda
11. ch buckle opener Attach the base to the bottom of the camera Align the tripod screw hole at the bottom of your camera with the screw of the base and tighten the screw 2 Tighten the screw Small hexagonal wrench Buckle opener Insert the camera into the marine case Jo Open up the LCD monitor Align the base attachment groove with the base to insert The camera turns on automatically when the LCD monitor is opened To turn off the camera Base attachment groove press and hold the power button for more than 2 seconds Base Marine case internal base 7 Adjust the angle of the LCD monitor The LCD monitor can be tilt upwards to a maximum angle of 30 degrees Seal the marine case Make sure that the O ring is not twisted and that you did not forget to attach it Make sure that foreign objects strap belt dirt etc have not been caught in between The risk of water leakage is extremely high if the O ring is twisted if you forget to attach it or if something is trapped in the seal Check that all the operation buttons of the camera are functioning properly If it is not functioning take out the camera and insert again Attach the grips Attach the grips lights or weights on the bottom of the marine case Large hexagonal wrench for screwing the grips Recording the Video Still Image Files Before recording Submerge t
12. e temp rature Minimisez la diff rence de temp rature le plus possible avant de prendre des photos sous l eau 4 Variation draconienne de pression de leau Si vous plongez soudainement dans une eau tr s profonde la variation draconienne pression de l eau peut causer la formation de bu e Nous vous recommandons de plonger graduellement dans des eaux profondes pendant la plong e NEDERLANDS Voorkomen dat het voorglas tijdens opnamen onder water beslaat Als men onder de volgende condities onder water opnamen maakt kan het voorglas beslaan Dit kan een negatieve invloed hebben op de beelden die men registreert Let op de volgende voorzorgsmaatregelen tijdens gebruik 1 Vocht in het onderwaterhuis Een kleine hoeveelheid vocht binnen het onderwaterhuis kan tijdens het maken van opnamen onder water tot gevolg hebben dat het glas beslaat Zorg ervoor dat de binnenkant van de zeebehuizing volledig droog is voor gebruik Let er goed op dat er geen water de behuizing binnensijpelt wanneer men de zeebehuizing opent sluit of wanneer men de camera bevestigt Let er met name op dat u de camera niet bevestigt als deze is aangeraakt door natte handen 2 Temperatuur en vochtigheid tijdens bevestiging van de camera Het glas kan beslaan tijdens opnemen onder water als de camera wordt bevestigd op een locatie die een hoge temperatuur of een hoog vochtigheidsniveau heeft Bevestig de camera of sla de camera op na hem te bevestigen op een loc
13. ergewissern Sie sich vor der Verwendung dass das Innere des Unterwassergehauses v llig trocken ist Lassen Sie auf keinen Fall beim Offnen SchlieBen des Unterwassergehauses oder beim Einsetzen der Kamera Wasser eindringen Setzen Sie vor allem die Kamera nicht ein wenn diese mit nassen H nden ber hrt wurde 2 Temperatur und Luftfeuchtigkeit beim Einsetzen der Kamera Wenn die Kamera an einem Ort mit hoher Temperatur oder Luftfeuchtigkeit eingesetzt wurde kann bei Unterwasseraufnahmen ein Beschlagen auftreten Setzten Sie die Kamera an einem Ort mit niedriger Temperatur und Luftfeuchtigkeit bzw lagern Sie sie dort nach dem Einsetzen 3 Temperaturunterschiede w hrend der Aufnahme Wenn die Kamera unmittelbar vor der Unterwasseraufnahme hoher Temperatur ausgesetzt wird wie etwa bei greller Sonne im Boot kann es aufgrund des groBen Temperaturunterschieds zu einem Beschlagen kommen Halten Sie den Temperaturunterschied vor der Unterwasseraufnahme m glichst gering 4 Starke Anderungen im Wasserdruck Wenn Sie pl tzlich in tiefes Wasser tauchen kann die starke nderung Wasserdruck ein Beschlagen hervorrufen Es wird empfohlen beim Tauchen allm hlich in tieferes Wasser vorzudringen FRANCAIS Pr venir la formation de bu e dans le hublot avant lors de la prise de photos sous
14. etely dry before use Pay careful attention not to allow water to enter the case when opening closing the marine case or when mounting the camera In particular do not mount the camera if it has been touched by wet hands 2 Temperature and humidity during camera mounting Fogging may occur during underwater shooting if the camera is mounted at a location that has a high temperature or humidity level Mount the camera or store the camera after mounting at a location with a low temperature and humidity level 3 Temperature difference during shooting If the camera is left under a high temperature such as under the hot sun on the boat immediately prior to underwater shooting fogging may occur due to the large temperature difference Minimize the temperature difference as much as possible before shooting underwater 4 Drastic change in water pressure If you dive suddenly into deep water the drastic change in water pressure may cause fogging to occur It is recommended that you move gradually into deep water during diving DEUTSCH So verhindern Sie dass sich das Frontglas bei Unterwasseraufnahmen beschlagt Unterwasseraufnahmen unter folgenden Bedingungen k nnen dazu f hren dass sich das Frontglas beschlagt was die Aufnahmequalitat beeintr chtigt Folgen Sie deshalb diesen VorsichtsmaBnahmen 1 Feuchtigkeit im Unterwassergehause Eine geringe Feuchtigkeitsmenge im Unterwassergehause kann bei Unterwasseraufnahmen ein Beschlagen verursachen V
15. he marine case with the camera inserted into a bathtub or water tank full of fresh water Gradually prolong the time the marine case is submerged as follows 1st time 5 10 seconds 2nd time 30 seconds 1 minute 3rd time 3 minutes 5 minutes try operating the levers and buttons while the marine case is submerged Always have someone hold the marine case for you when diving into or getting out of water to prevent loss or damages f for any reason water leakage occurs remove the camera battery It may cause the camera to explode o Turn on the camera s power Press and hold the power button for more than 2 seconds to turn on the power The camera s power lamp lights and the monitor turns on ON OFF 2 Sometimes due to sudden shaking or impact to the marine case the camera s drop detection function operates to turn off the camera s power When the camera s power is turned off turn it on again When VIDEO MANAGEMENT FILE IS BROKEN TO RECORD PLAYBACK VIDEO RECOVERY IS REQUIRED RECOVER is displayed press the REC button to recover the file Press the video recording start stop button or the still image lever to start recording Zooming Tele gt Zooming Still image lever Wide Shoot still images Video recording start stop button Start stop the video recording When you have finished recording press and hold the power button for more than 2
16. l eau Prendre des photos sous l eau dans les conditions suivantes peut causer la formation bu e dans le hublot avant ce qui pourrait nuire a la qualit des images prises Prenez note des pr cautions suivantes lors de l utilisation 1 Humidit a int rieur du bo tier sous marin Un peu d humidit dans le bo tier sous marin peut causer la formation de bu e pendant la prise de photos sous leau Assurez vous que l int rieur du bo tier sous marin soit compl tement sec avant l utilisation Faites tr s attention de ne pas laisser d eau s infiltrer dans le bo tier au moment d ouvrir ou de fermer le bo tier sous marin ou lors du montage de l appareil photo Ne montez surtout pas l appareil photo s il a t manipul par une personne avec les mains mouill es 2 Temp rature humidit au moment du montage de l appareil photo La formation de bu e peut se produire pendant la prise de photos sous l eau si l appareil photo est mont un endroit o temp rature ou le niveau d humidit sont lev s Montez l appareil photo ou entreposez le apr s le montage a un endroit o la temp rature et le niveau d humidit sont peu lev s 3 Diff rence de temp rature lors de la prise de photos Si l appareil photo est soumis a une temp rature lev e comme un soleil chaud sur un bateau imm diatement avant la prise de photos sous l eau la formation de bu e peut avoir lieu en raison de l importante diff rence d
17. materials video camera SD card etc or any expenses incurred in taking the photographs video Therefore please be careful when using the marine case Safety Precaution Before use this unit must be tested to check if there is any water leakage Please read before use This marine case is a precision instrument designed to permit safe video recording under high water pressure Please pay careful attention when handling the unit before and after use as explained in this users manual Each part of the marine case has been subject to strict controls during the manufacturing process and the individual functions have faced stringent tests during the assembly process Each marine case has also had to pass waterproof inspections using high pressure water testers However damage can sometimes occur during transport and distribution or during storage after purchase so before diving always carry out the following pre use test to verify safety Pre use test Be sure to perform the following pre use test before diving 1 Before mounting the camera inside the marine case dive with only the empty marine case and test for water leaks Allow 5 or 6 minutes to ensure there are no leaks Be sure to perform this test to ensure the safety of your camera 2 The following are some common causes of water leaks A The marine case is used without attaching the O ring B The O ring is not mounted in the correct
18. ng or buckles enter the case water droplets from your hair or your body enter the case P Remove the O ring and wipe off salt sand and other foreign matter Also wipe the groove in which the O ring was inserted and the part of the marine case that was in contact with the O ring and allow them to dry For details on handling and storing the O ring refer to the O ring Maintenance Manual Wipe the inside and outside of the marine case with a dry cloth Use a lint free cloth to wipe the inside of the marine case 7 Wipe the inner side of the front glass Add a few drops of the cleaner liquid commercially available onto the inner side of the front glass and wipe off using a lens tissue paper clean cloth etc The front glass will fog if it is dirty Let it dry completely in a shaded area Do not leave the marine case in direct sunlight Doing so may cause discoloration of the case and may cause the O ring to deteriorate more quickly The conditions may vary depending on the environment of use such as temperature humidity water temperature salinity and others Storing the O ring If you do not intend to use the marine case for longer than one month remove and store the O ring away For details refer to the O ring Maintenance Manual Wi The O ring is an expendable part Replace the O ring with a brand new one every year When re using
19. or de O ring Manual de mantenimiento de la junta torica Manuale di manutenzione dell anello circolare Instrukcja konserwacji pier cienia 2 2 AE T ali KARR KAFAD lt K BY il DABO KS TAMAR JOY RADAICC BODE 1 9 00100050 9 CHAO Id CSL CL 1 VUYIT ANBOKACDUT ck AO er e D DEE A de Ed bien lc VUYT ANBOTAICHLIYCUS CE See CT lt 7 0 7 ABERDEEN SBI KOBA SEUK SIC TING CER ore EFADAXAXADREDEKBBISCEAIIT CHER 2 EFANXDREHOmE mz SUOwBMCETANXD eReIT lt 9 amp Bld MEOW CIID GL BYKO RES RA ROM OIC SL 5 Ok Or EE DE d CC D n Jo KR ATO CEA ek TR ED UCD SIR UT CIES 4 AAKE kE KORE ACRDVAL TIC zl AKT OC BAMUISLABIECCBODRETSOCEDOOED SKI PNC 28 ZBISTDLETD ENGLISH Preventing fogging of the front glass during underwater shooting Performing underwater shooting under the following conditions may cause the front glass to fog thus affecting the quality of the images taken Take note of the following precautions during use 1 Moisture inside marine case A slight amount of moisture inside the marine case may cause fogging during underwater shooting Make sure that the interior of the marine case is compl
20. s 2 Temperatura y humedad durante la instalaci n de la c mara Se puede producir un empa amiento al realizar disparos submarinos si se coloca la c mara en un sitio donde el nivel de temperatura o humedad sea elevado Coloque o guarde la c mara luego de instalarla en un sitio donde el nivel de temperatura y de humedad sea bajo 3 Diferencia de temperatura durante el disparo Si se deja la c mara expuesta a altas temperaturas como puede ser bajo el sol en el bote inmediatamente antes de efectuar disparos submarinos se podr a producir un empa amiento debido a la gran diferencia de temperatura Reduzca la diferencia de temperatura tanto como pueda antes de efectuar disparos submarinos 4 Cambio dr stico en la presi n hidrost tica Si se sumerge bruscamente en aguas profundas el cambio dr stico en la presi n hidrost tica podr a provocar un empa amiento Se sugiere se desplace de manera gradual en aguas profundas mientras bucea LYT2112 003A 0509MNH SW OT
21. seconds to turn off the camera The camera s power lamp goes out and the monitor turns off Detaching the camera If there is a need to detach immediately Submerge the marine case in fresh water and shake the marine case in the upward downward left and right directions for at least 10 times followed by rinsing it o Remove the marine case and wipe off water droplets on the case surface using a dry towel Face the front glass of the marine case upwards and open the buckles to remove the camera while paying attention not to let water droplets at O ring or buckles enter the case 4 Upon removing the camera close the marine case again while paying attention not to allow water droplets enter the case followed by tightening all the buckles Always perform maintenance on the marine case after using c Pg 10 If there is no need to detach immediately Perform maintenance on the marine case Pg 10 10 Maintenance on the marine case 3 The camera may fall out if the buckles are Always perform maintenance on the marine case opened with the front glass facing down after you have finished recording D We de If you cannot avoid opening the marine case at Salt crystal or dirt will accumulate inside the the diving location pay attention not to let marine case if maintenance is not performed and this can cause water leakage Wash the marine case in water while it is still sealed
22. y it can cause water leakage Apply grease to the O ring and re attach 4 Close the empty marine case no camera inside Submerge the marine case in water and check that there are no water leaks Pg 8 7 Fold the grip belt Attaching the Marine Case to the Make sure the grip belt is not caught Camera between the marine case when sealing Setup the camera 1 Unlock the grip belt pull the belt out and For models equipped with light turn off the lock again light Lock Open the lens cover Set to the shooting mode video still 5 image 5 Even when the shooting mode is set to 2 Fold the grip belt and pass the front end video still images can be captured by through the inner side of the belt pressing the still image lever during video recording is recommended to set to the auto shooting mode Insert the battery and micro SD card beforehand if needed 3 Pull the end that has been passed through the inner side of the belt and adjust the To turn off the camera press and hold the length If the end is pulled out too much it power button for more than 2 seconds may be recorded into the image or get Insert the drying agent at the back of the caught in the O ring when sealing the base marine case a SH Drying agent Open the marine case Pass underneath If itis difficult to open buckles use the small hexagonal wren
Download Pdf Manuals
Related Search