JVC KD-S711R User's Manual
Contents
1. COMPACT DIGITAL AUDIO e Other discs cannot be played back Center holder How to handle CDs When removing a CD from its case press down the center holder of the case and lift the CD out holding it by the edges e Always hold the CD by the edges Do not touch its recording surface When storing a CD into its case gently insert the CD around the center holder with the printed surface facing up e Make sure to store CDs into the cases after use To keep CDs clean A dirty CD may not play correctly If a CD does become dirty wipe it with a soft cloth in a straight line from center to edge To play new CDs New CDs may have some rough spots around the inner and outer edges If such a CD is used this unit may reject the CD To remove these rough spots rub the edges with a pencil or ball point pen etc About mistracking Mistracking may result from driving on extremely rough roads This does not damage the unit and the CD but will be annoying We recommend that you stop CD play while driving on such rough roads Moisture condensation Moisture may condense on the lens inside the CD player in the following cases After starting the heater in the car If it becomes very humid inside the car Should this occur the CD player may malfunction In this case eject the CD and leave the unit turned on for a few hours until the moisture evaporates When playing a CD R Record2. FM broadcast Selected band appears Audio see page 21 or volume level 2 Press and hold i or IM until indicator M manual starts flashing on the pee display This receiver has three FM bands FM1 FM2 FM3 You can use any one of them to listen to an FM broadcast 2 Start searching a station Press gt A to search stations of higher frequencies H a a Press Lea sw to search T stations of lower Selected band appears frequencies When a station is received searching stops 3 Tune into a station you want while M is flashing Press gt gt A to search stations of higher frequencies Press 44 to search stations of lower frequencies e If you release your finger from the button the manual mode will automatically turn off after 5 seconds If you hold down the button the frequency keeps changing in 50 kHz intervals for FM and 9 kHz intervals for AM MW LW until you release the button When an FM stereo broadcast is hard to receive Press MO RND monaural random while listening to an FM stereo broadcast Each time you press the button the MO indicator lights up and goes off alternately Lights up when receiving an FM broadcast in stereo Ei T F RW LL ri AEA ee IT MO RND When the MO indicator is lit on the display the sound you hear becomes monaural
3. e Die Sicherung brennt durch Sind die roten und schwarzen Leitungen richtig angeschlossen e Stromversorgung kann nicht eingeschaltet werden Ist die gelbe Leitung angeschlossen e Kein Ton aus den Lautsprechern Ist die Lautsprecherausgangsleitung kurzgeschlossen e Ton verzerrt Ist die Lautsprecherausgangsleitung geerdet Sind die Anschlu klemmen der linken und rechten Lautsprecher zusammen geerdet e Ger t wird hei Ist die Lautsprecherausgangsleitung geerdet Sind die Anschlu klemmen der linken und rechten Lautsprecher zusammen geerdet e Le fusible saute Les fils rouge et noir sont ils racord s correctement e Lappareil ne peut pas tre mise sous tension Le fil jaune est elle raccord e e Pas de son des haut parleurs Le fil de sortie de enceinte est il court circuit e Le son est d form Le fil de sortie de enceinte est il a la masse Les bornes des enceintes gauche et droit sont elles mises ensemble a la masse Lappareil devient chaud Le fil de sortie de enceinte est il a la masse Les bornes des enceintes gauche et droit sont elles mises ensemble a la masse
4. and unlink the sound modes and the playback sources When shipped from the factory a different sound mode can be stored in memory for each source so that you can change the sound modes simply by changing the sources e UNK ON Advanced SCM different sound modes for different sources e LINK OFF Conventional SCM one sound mode for all sources To select the level meter LEVEL You can select the level display according to your preference When shipped from the factory AUDIO 2 is selected e AUDIO 1 Level meter illuminates from bottom to top e AUDIO 2 Alternates level meter moves from bottom to top and illumination display e OFF Erases the audio level indicator or To select the telephone muting TEL This mode is used when a cellular phone system is connected Depending on the phone system used select either MUTING 1 or MUTING 2 whichever mutes the sounds from this unit When shipped from the factory this mode is deactivated e MUTING 1 Select this if this setting can mute the sounds Select this if this setting can mute the sounds Cancels the telephone muting e MUTING 2 e OFF ENGLISH 21 ar Detaching the control panel Attaching the control panel 1 Insert the left side of the control panel You can detach the control panel when leaving into the groove on the panel holder the car When detaching or attaching the control panel be careful n
5. die entsprechenden Riegel umknicken um die Halterung an ihrem Platz zu sichern siehe Abbildung 5 Die Befestigungsschraube an der R ckseite des Ger tek rpers befestigen und das Ende der Schraube mit einem Gummipuffer abdecken 6 Nehmen Sie die erforderlichen elektrischen Anschl sse vor 7 Das Ger t in die Halterung schieben bis es einrastet 8 Befestigen Sie die Frontrahmen in der Form da der Fortsatz der Frontrahmen auf der linken Seite des Ger ts befestigt wird 9 Die Schalttafel anbringen 1 Avant le montage Appuyez sur IAI d blocage du panneau de commande pour ventuellement d tacher le panneau de commande Lorsque ce panneau de commande sort d usine il est range dans un tui de transport 2 Retirer la plaque d assemblage 3 Lib rer les verrous du manchon et retirer le manchon Poser l appareil a la verticale Remarque Lorsque vous mettez l appareil a la verticale faire attention de ne pas endommager le fusible situ sur l arriere Ins rer les 2 poign es entre l appareil et le manchon comme indiqu pour d sengag les verrous de manchon Retirer le manchon Remarque S assurer de garder les poign es pour une utilisation ult rieur apr s l installation de l appareil 4 Installer le manchon dans le tableau de bord Apres installation correcte du manchon dans le tableau de bord plier les bonnes pattes pour maintenir fermement le manchon en place comme monire 5 Mon
6. release the rear section Remove the control panel Remove the trim plate Insert the 2 handles into the slots as shown Then while gently pulling the handles away from each other slide out the unit Be sure to keep the handles after installing it 1 2 3 Ausbau des Gerats e Vor dem Ausbau des Ger ts den hinteren Teil freigeben 1 Die Schalttafel herausnehmen Den Frontrahmen abnehmen Die 2 Griffe in die Schlitze wie gezeigt stecken Dann die Griffe behutsam auseinander ziehen und das Ger t herausziehen Die Griffe nach dem Einbau auf jeden Fall aufbewahren 2 3 Retrait de l appareil e Avant de retirer l appareil lib rer la section arri re 1 Retirer le panneau de commande 2 Retirer la plaque d assemblage A Introduire les deux poign es dans les fentes comme montr Puis tout en tirant doucement les poign es cart es faire glisser l appareil pour le sortir S assurer de conserver les poign es apres l installation de l appareil Control Panel Schalttafel Panneau de command Trim plate Frontrahmen Plaque d assemblage 3 Handle Griff Poign e Parts list for installation and connection The following parts are provided with this unit After checking them please set them correctly Hard case Control Panel Etui Schalttafel Etui de transport Panneau de command Power cord Handles Stromkabel Griffe Cordon d alimentation Poign es Teileliste
7. 7 12 Press and hold 1 7 6 12 for more than 1 second E 0 NIS Selecting CD playback modes To play back tracks at random Random Play You can play back all tracks on the CD at random Each time you press MO RND monaural random while playing a CD CD random play mode turns on and off alternately WW x w RND a ATI I d vu PR The RND indicator When the random mode is turned on the RND indicator lights up on the display and a track randomly selected starts playing ENGLISH 15 ba H OH Z m 16 Prohibiting CD ejection You can prohibit CD ejection and can lock a CD in the loading slot Press and hold CD and 4 for more than 2 seconds S Am a Re e EJECT flashes on the display for about 5 seconds and the CD is locked and cannot be ejected To cancel the prohibition and unlock the CD press and hold CD and 4 again for more than 2 seconds while pressing CD EJECT appears on the display and the CD ejects from the loading slot SOUND ADJUSTMENTS Adjusting the sound You can adjust the sound characteristics to your preference 1 Select the item you want to adjust Each time you press the button the adjustable items change as follows 2 Adjust the level To decrease the level LOC IL ag gt BAS gt TRE gt FAD p bass treble f
8. S811R SEULEMENT POUR LE KD S811R Se vd el sl el Fuse position 2 2 Sicherungsposition Position de fusible 2 Bil Bs 5 el B2 ed Be Be FOR KD S811R FOR KD S713R KD S711R I as aal Fuse position 1 1 Sicherungsposition al aa sel asf Position de fusible 1 F R KD S811R F R KD S713R KD S711R Rear ground terminal Hintere Erdungscanschlu klemme Borne arri re de masse L Aerial terminal ei Line out see diagram Eq Schutz kappen Signalausgang siehe Schaltplan EJ Sortie de ligne voir le diagramme EJ To aerial Zur Antenne A l antenne 1 Before checking the operation of this unit prior to installation this lead must be connected otherwise power cannot be turned on Vor der berpr fung der Funktionsf higkeit des Ger ts vor dem Einbau mu diese Leitung angeschlossen werden da sonst die Stromversorgung nicht eingeschaltet werden kann Pour v rifier le fonctionnement de cet appareil avant installation ce fil doit tre raccord sinon l appareil ne peut pas tre mis sous tension a E Blanc avec bande noire Left speaker front Linker Lautsprecher vorne Enceinte gauche avant Antennenanschlu klemme Borne de l antenne Fee T Gris avec bande noire del sl al 1 wee ee eae Bet ER 1
9. Vis en option Mounting bolt Befestigungsschraube Boulon de montage es When installing the unit without using the sleeve es Beim Einbau des Ger ts ohne Halterung e Lors de l installation de l appareil scans utiliser de manchon In a Toyota for example first remove the car radio and install the unit in its place Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Ger t an seinem Platz einbauen Par exemple dans une Toyota retirer d abord l autoradio et installer l appareil a la place Flat type screws M5 x 6 mm Senkkopfschrauben M5 x 6 mm Vis a t te plate M5 x 6 mm Not included with this unit Nicht Teil dieses Ger ts Non fourni avec cet appareil Bracket Konsole Support Pocket Ge Flattype screws M5 x 6 mm Den en Senkkopfschrauben M5 x 6 mm eee S Vis a t te plate M5 x 6 mm Support Note When installing the unit on the mounting bracket make sure to use the 6 mm long screws If longer screws are used they could damage the unit Hinweis Beim Anbringen des Ger t an der Konsole sicherstellen da 6 mm lange Schrauben verwendet werden Werden l ngere Schrauben verwendet k nnen sie das Ger t besch digen Remarque Lors de l installation de l appareil sur le support de montage s assurer d utiliser des vis d une longueur de 6 mm Si des vis plus longues sont utilis es elles peuvent endommager l appareil Removing the unit Before removing the unit
10. holder in the direction indicated by the arrow using a ball point pen or a similar tool 2 Remove the battery holder back side 1 2 Place the battery Slide the battery into the holder with the side facing upwards so that the battery is fixed in the holder A 7 Lithium coin battery product number CR2025 3 Return the battery holder Insert again the battery holder pushing it until you hear a clicking sound back side EB WARNING Store the battery in a place where children cannot reach Ifa child accidentally swallows the battery consult a doctor immediately Do not recharge short disassemble or heat the battery or dispose it in a fire Doing any of these things may cause the battery to give off heat crack or start a fire Do not leave the battery with other metallic materials Doing this may cause the battery to give off heat crack or start a fire When throwing away or saving the battery wrap it in tape and insulate otherwise the battery may start to give off heat crack or start a fire Do not poke the battery with tweezers or similar tools Doing this may cause the battery to give off heat crack or start a fire ENGLISH 23 I H I Z m 24 B Using the remote controller on Oo Sy DISC Or Functions the same as the 1 ATT button on t
11. masse NEGATIVE Si votre v hicule n offre pas ce type d alimentation il vous faut un convertisseur de tension que vous pouvez acheter chez un revendeur d autoradios JVC e Remplacer le fusible par un de la valeur pr cis e Si le fusible saute souvent consulter votre revendeur d autoradios JVC Si le bruit est un probleme Cet appareil incorpore un filtre de bruit dans le circuit d alimentation Cependant avec certains v hicules quelques claquements ou autres bruits non d sir s risquent de se produire Si cela arrive raccorder la borne arri re de masse de l appareil au chassis de la voiture voir le diagramme de raccordement en utiliscant des cordons les plus gros et les plus courts possibles telle qu une barre de cuivre ou une tresse Si le bruit persiste consulter votre revendeur d autoradios JVC Pour KD S811R La puisscance admissible des haut parleurs doit tre sup rieure a 45 W l arri re et a 45 W l avant avec une imp dance de4Q 8 Q Pour KD S713R KD S711R La puisscance admissible des haut parleurs doit tre sup rieure 40 W l arri re et 40 W l avant avec une imp dance de 49 a8 Q S assurer de raccorder la mise la masse de cet appareil au ch ssis de la voiture Le dissipateur de chaleur devient tr s chaud apr s usage Faire attention de ne pas le toucher en retirant cet appareil E Typical Connections Typische Anschl sse Before connecting Check the wiring in th
12. no station broadcasting a programme of the same PTY code you selected the station will not change Note In some areas the PTY search will not work correctly Other convenient RDS functions and adjustments Automatic selection of the station when using the number buttons Usually when you press the number button the preset station is tuned in However when the preset station is an RDS station something different will happen If the signals from that preset station are not sufficient for good reception this unit using the AF data tunes in another frequency broadcasting the same programme as the original preset station is broadcasting Programme search To activate programme search follow the procedure below Programme search takes a while See also Changing the general settings PSM on page 19 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display 2 Press PI A or aa wv to select P Programme SEARCH 3 Rotate the control dial clockwise to select ON Now programme search is activated To cancel programme search repeat the same procedure and select OFF in step 3 by rotating the control dial counterclockwise Changing the display mode while listening to an FM station You can change the initial indication on the display to station name PS NAME station frequency FREQ or Clock time CLOCK while listening to an FM
13. on the clock time is shown for 5 seconds then the power turns off Changing the general settings PSM You can change the items listed on the next page by using the PSM Preferred Setting Mode control ENGLISH Basic Procedure 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display See page 20 4 Repeat steps 2 and 3 to adjust the other PSM items if necessary 5 Finish the setting 19 ar Preferred Setting Mode PSM items ba 2 m Oo Z m Factory preset settings ws Counter Select clockwise Clockwise CLOCK H Hour adjustment Advance CLOCK M Minute adjustment Back Advance 0 00 SCM LINK Sound control LINK OFF LINK ON LINK ON memory linkage 24H 12H 24 12 hour time display 12H 24H 24H AUTO ADJ Automatic clock setting OFF ON ON DISPMODE Display mode PS NAME gt FREQ PS NAME t cock at S PTY STBY PTY standby 29 programme types NEWS PTY SRCH PTY search ee Paget See page 11 TA VOL Traffic announcement VOL 00 VOL 50 VOL 20 volume P SEARCH Programme search OFF ON OFF LEVEL Level display AUDIO1 AUDIO2 L oF 4 TEL Telephone muting MUTING 1 MUTING 2 t OFF gt eq AUDIO 2 e Press SEL select to finish the setting 20 To cancel Advanced SCM SCM LINK You can cancel the Advanced SCM Sound Control Memory
14. or music etc Another advantage of RDS function is called EON Enhanced Other Networks The EON indicator lights up while receiving an FM station with the EON data By using the EON data sent from a station you can tune into a different station of a different network broadcasting your favorite programme or traffic announcement while listening to another programme or to another source such as CD By receiving the RDS data this unit can do the following Tracing the same programme automatically Network Tracking Reception Standby Reception of TA Traffic Announcement or your favorite programme PTY Programme Type search Programme search And some other functions Tracing the same programme automatically Network Tracking Reception When driving in an area where FM reception is not good the tuner built in this unit automatically tunes into another RDS station broadcasting the same programme with stronger signals So you can continue to listen to the same programme in its finest reception no matter where you drive See the illustration on the next page Two types of the RDS data are used to make Network Tracking Reception work correctly PI Programme Identification and AF Alternative Frequency Without receiving these data correctly from the RDS station you are listening to Network Tracking Reception will not operate RDS OPERATIONS A To use Network Tracking Reception press an
15. 5 A Sicherung 10 A Sicherung Not included with this unit FREE Fusible 15A__ __ _ Fusible 04 i Wird nicht mit Ger t mitgeliefert Ek Ignition switch Black Non fourni avec cet appareil Z ndschalter Schwarz To metallic body or chassis of the car Interrupteur d allumage Noir eei Autos Yellow Gelb Jaune bypassing the ignition swich Zur einer stromf hrenden Anschlu klemme o a Blue with white stripe Blau mit wei em Streifen Bleu avec bande blanche Red To power aerial if any Ba Brown Braun Marron White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple Wei mit schwarzem Wei Grau mit schwarzem Grau Gr n mit schwarzem OO 4 Gr n Lila mit schwarzem Streifen O 4 Lila Streifen Blanc Streifen Gris Streifen Vert Violet avec bande noire Violet Vert avec bande noire Right speaker front Rechter Lautsprecher vorne Enceinte droit avant Zur metallenen Karosserie oder zum Fahrwerk des Vers corps m tallique ou chassis de la voiture To a live terminal in the fuse block connecting to the car battery Anschlie en an die Autobatterie Umgehen des Z ndschalters A une borne sous tension du porte fusible connect e a la batterie de la voiture en d rivant l interrupteur d allumage To an accessory terminal in the fuse block Zur einer Zubeh ranschlu klemme im Sicherungsblock Vers borne accessoire du p
16. AVANT de connecter les fils d enceintes du cordon d alimentation aux enceintes verifiez le c blage des enceintes de votre voiture Si le c blage des enceintes de votre voiture est r alis comme montr sur la Fig 1 ou Fig 2 ci dessous NE CONNECTEZ PAS l appareil en utiliscant ce c blage original d enceintes Si vous le faites l appareil sera s rieusement endommag Recommencez le c blage des enceintes de fagon que vous puissiez connecter l appareil aux enceintes comme montr sur la Fig 3 Si le c blage des enceintes de votre voiture est comme montr sur la Fig 3 vous pouvez connecter l appareil en utiliscant ce cablage original d enceintes pour votre voiture Si vous n tes pas s rs du c blage d enceintes de votre voiture consulter le concessionnaire de votre voiture Twist the core wires when connecting Die Kerndr hte beim Anschlie en verdrehen Torsader les mes des fils en les Solder the core wires to connect them securely Die Kerndr hte anl ten um sie fest anzuschlie en Souder les mes des fils pour les raccorder entre eux de fa on s re raccordant ING CAUTION VORSICHT PRECAUTION To prevent short circuit cover the terminals of the UNUSED leads with insulating tape Zur Vermeidung eines Kurzschlusses die Anschlu klemmen der NICHT VERWENDETEN Leitungen mit Isolierklebeband umwickeln Pour viter les court circuits couvrir les borne
17. DE BORD e The following illustration shows a typical installation However e Die folgende Abbildung zeigt einen typischen Einbau Denno ch Lillustration suivante est un exemple d installation typique you should make adjustments corresponding to your specific car If you have any questions or require information regarding installation kits consult your JVC IN CAR ENTERTAINMENT dealer or a company supplying kits m ssen Sie entsprechend Ihrem jeweiligen Auto Anpassungen vornehmen Bei irgendwelchen Fragen oder wenn Sie Informationen hinsichtlich des Einbausatzes brauchen wenden Sie sich an ihren JVC Autoradioh ndler oder ein Unternehmen Cependant vous devez faire les ajustements correspondant a votre voiture particuli re Si vous avez des questions ou avez besoin d information sur des kits d installation consulter votre revendeur d autoradios JVC ou une compagnie das diese Einbausaize vertreibt d approvisionnement 1 Before mounting Press L amp Control Panel Release button to detach the control panel if already attached When shipped from the factory the control panel is packed in the hard case 2 Remove the trim plate 3 Remove the sleeve after disengaging the sleeve locks Stand the unit Note When you stand the unit be careful notto damage the fuse on the rear Insert the 2 handles between the unit and the sleeve as illustrated to disengage the sleeve locks Remove the slee
18. JVC MM ENGLISH m m I dp CD RECEIVER CD RECEIVER G RECEPTEUR CD CD RECEIVER KD S811R KD S713R KD S711R FRANCAIS KD S811R NEDERLANDS COMPACT DIGITAL AUDIO For installation and connections refer to the separate manual F r den Einbau und die Anschl sse siehe das eigenst ndige Handbuch Pour l installation et les raccordements se r f rer au manuel s par Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D INSTRUCTIONS GEBRUIKSAANWIJZING GET0013 001A E Position And Reproduction Of Labels Bottom panel of the main unit DANGER Invisible laser ADVARSEL Usyniiglase VARNING Osynliglaser VARO Avattaessa ja suo ES radiation when open and str ling ved bning nar str lning nar dennadel jalukitus ohitettaessa olet interlock failed or defeeted sikkerhedsafbrydere er ude r 6ppnadoch sp rren r alttiina n kym tt m lle AVOD DIRECT EXPOSURE af funktion Undgaudseet urkopplad Betrakta ej lasers teilylie Ala katso Name Rating plate I H 0 Z m TO BEAM e tase for str
19. M rel ENGLISH 17 ba H Oo Z m 18 e When SCM LINK is set to LINK ON the selected sound mode can be stored in memory for the current source and the effect applies only to the current source Each time you change the playback source the SCM indicator flashes on the display When SCM LINK is set to LINK OFF the selected sound mode effect applies to any source Indication For Preset values BAS TRE LOUD BEAT Rock or disco 02 00 ON music SOFT Quiet 01 03 OFF background music POP Light music 04 01 OFF SCM OFF Flat sound 00 00 ON Recalling the sound modes When SCM LINK is set to LINK ON Select the source IN The sound mode stored in memory for the selected source is recalled Notes You can adjust each sound mode to your preference and store it in memory If you want to adjust and store your original sound mode see Storing your own sound adjustments on the right column To adjust the bass and treble reinforcement levels or to turn on off the loudness function temporarily see page 17 Your adjustments will be canceled if another source is selected Storing your own sound adjustments You can adjust the sound modes BEAT SOFT POP to your preference and store your own adjustments in memory There is a time limit in doing the following procedure If the setting is ca
20. RDS station See also Changing the general settings PSM on page 19 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display 2 Press BPI A or ea w to select DISPMODE display mode 3 Rotate the control dial to set to the desired indication PS NAME FREQ or CLOCK Note By pressing DISP you can also change the display while listening to an FM RDS station Each time you press the button the following information appears on the display Station name _ Station frequency PS NAME FREQ CLOCK Programme type Clock time PTY Then the display goes back to the original indication in several seconds Setting the TA volume level You can preset the volume level for TA Standby Reception When a traffic programme is received the volume level automatically changes to the preset level See also Changing the general settings PSM on page 19 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display 2 Press PI A or ea w to select TA VOL 3 Rotate the control dial to set to the desired volume You can set it from VOL 00 to VOL 50 Automatic clock adjustment When shipped from the factory the clock built in this unit is set to be readjusted automatically using the CT Clock Time data in the RDS signal If you do not want to use automa
21. Sicherung h ufig durch wenden Sie sich an ihren JVC Autoradioh ndler Sind St rger usche ein Problem Dieses Ger t enth lt ein St rfilter im Stromkreis Bei manchen Fahrzeugen kann jedoch ein Klicken oder andere unerw nschte St rger usche auftreten Sollte das der Fall sein die hintere Erdungscanschlu klemme siehe Schaltplan des Ger ts am Fahrwerk des Fahrzeugs anschlie en dabei k rzere und dickere Kabel wie beispielsweise Kupfergeflechtdraht oder Stahldraht verwenden Bleibt St rger usch bestehen wenden Sie sich an Ihren JVC Autoradioh ndler F r KD S811R Maximale Eingangsleistung der Lautsprecher mu h her als 45 W hinten und 45 W vorne sein mit einer Impedanz von 4Q bis 8 Q F r KD S713R KD S711R Maximale Eingangsleistung der Lautsprecher mu h her als 40 W hinten und 40 W vorne sein mit einer Impedanz von 4 Q bis 8 Q Sicherstellen da das Ger t am Fahrwerk geerdet wird Das Abstrahlblech wird nach dem Gebrauch sehr hei Beim Ausbau des Ger ts darauf achten das Abstrahlblech nicht zu ber hren Pour viter tout court circuit nous vous recommandons de d brancher la borne negative de la batterie et d effectuer tous les raccordements lectriques avant d installer l appareil Si l on n est pas s r de pouvoir installer correctement cet appareil le faire installer par un technicien qualifie Remarque Cet appareil est con u pour fonctionner sur des sources de courant continu de 12V a
22. Y standby mode SEARCH appears on the display and PTY station search starts When a PTY station is tuned in the PTY indicator is lit E If you are listening to a CD and wish to listen to a selected PTY broadcast press PTY to enter the PTY standby mode The PTY indicator lights up If the selected PTY programme starts broadcasting while the PTY standby mode is active the selected PTY name appears and the playback source changes to the FM band The selected PTY programme can then be heard To deactivate the PTY standby mode press PTY again Selecting your favorite programme for PTY Standby Reception You can select your favorite programme for PTY Standby Reception to store in memory When shipped from the factory NEWS is stored as the programme type for PTY Standby Reception 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display PSM see page 20 2 Select PTY STBY standby if not shown on the display 3 Select one of twenty nine PTY codes Selected code name appears on the display and is stored into memory e For details see the table below A Searching your favorite programme You can search one of your 6 favorite programme types stored in memory When shipped from the factory the following 6 programme types have been stored in the number buttons 1 to 6 To store your favorite programme types see below To sear
23. able You can play back your original CD Rs on this receiver e Before playing back CD Rs read their instructions or cautions carefully Some CD Rs recorded on CD recorders may not be played back on this receiver because of their disc characteristics and of the following reasons Discs are dirty or scratched Moisture condensation occurs on the lens inside the unit The pickup lens inside the CD player is dirty Use only finalized CD Rs CD RWs Rewritable cannot be played back on this receiver Do not use CD Rs with stickers or sticking labels on the surface They may cause malfunctions CAUTIONS Do not insert 8 cm CDs single CDs into the loading slot Such CDs cannot be ejected Do not insert any CD of unusual shape like a heart or flower otherwise it will cause a malfunction Do not expose CDs to direct sunlight or any heat source or place them in a place subject to high temperature and humidity Do not leave them in a car Do not use any solvent for example conventional record cleaner spray thinner benzine etc to clean CDs AUDIO AMPLIFIER SECTION For KD S811R Maximum Power Output Front 45 W per channel Rear 45 W per channel Continuous Power Output RMS Front 17 W per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 8 total harmonic distortion Rear 17 W per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 8 total harmonic distorti
24. ader Equalization pattern changes as you adjust VOL lt LOUD lt BAL lt the bass or treble volume loudness balance Note Normally the control dial works for volume Indication To do Range adjustment So you do not have to select VOL to BAS Adjust the bass 06 min adjust the volume level 06 max TRE Adjust the treble 06 min Using the Sound Control 06 max Memory SCM FAD Adjust the front DOG Rear only and rear speaker You can select and store a preset sound adjustment balance F06 Front only suitable for each playback source BAL Adjust the left LO6 Left only Advanced SCM and right speaker S balance RO6 Right only Selecting and storing the sound modes LOUD Boost low and high Once you select a sound mode it is stored in nn D SH ON memory It will be recalled every time you select produce a Wen the same source and will be shown on the display en EEN A sound mode can be stored for each of the level following sources FM1 EMS FM3 AM and CD e If you do not want to store the sound mode VOL Adjust the volume 00 min separately for each playback source but want to al imax use the same sound mode for all the sources see To cancel Advanced SCM on page 21 If you are using a two speaker system set the fader level to 00 Select the sound mode you want Each time you press the button the sound mode changes as follows gt BEAT gt SOFT gt POP SC
25. ande a distance bleu avec bande blanche au fil de commande a distance de l autre appareil de fa on qu il puisse tre command via cet appareil Pour l amplificateur seulement Raccorder les bornes de sortie ligne de cet appareil aux bornes d entr e ligne de l amplificateur D connectez les enceintes de cet appareil et connectezles l amplificateur Laissez les fils d enceintes de cet appareil inutilis s Recouvrir les extr mit s de ces fils inutilis s avec de la bande isolante comme montr ci dessus CAUTION VORSICHT PRECAUTION To prevent internal heat buildup inside this unit place this unit UNDER the other equipment Zur Vermeidung eines Hitzestaus in diesem Ger t dieses Ger t UNTER die andere Ger teansr stung stellen e Pour viter un chauffement interne de cet appareil placez le SOUS lautre appareil TROUBLESHOOTING FEHLERSUCHE EN CAS DE DIFFICULTES e The fuse blows Are the red and black leads connected correctly Power cannot be turned on Is the yellow lead connected No sound from the speakers Is the speaker output lead short circuited Sound is distorted Is the speaker output lead grounded Are the terminals of L and R speakers grounded in common e Unit becomes hot Is the speaker output lead grounded Are the terminals of L and R speakers grounded in common
26. but the reception will be improved the ST indicator goes off h FMAM ES Storing stations in memory You can use one of the following two methods to store broadcasting stations in memory e Automatic preset of FM stations SSM Strong station Sequential Memory e Manual preset of both FM and AM stations FM station automatic preset SSM You can preset 6 local FM stations in each FM band FM1 FM2 and FM3 1 Select the FM band EM 3 you want to store FM stations into Each time you press the button the FM band changes as follows g 2 Press and hold both buttons for more than 2 seconds gt FM1 gt FM2 gt FM3 Ee SSM appears then disappears when automatic preset is over Ca Y II Local FM stations with the strongest signals are searched and stored automatically in the band number you have selected FM1 FM2 or FM3 These stations are preset in the number buttons No 1 lowest frequency to No 6 highest frequency When automatic preset is over the station stored in number button 1 will be automatically tuned in ENGLISH W FA Manual preset Notes e A previously preset station is erased when a new station You can preset up to 6 stations in each band FM1 is stored in the same preset number FM2 FM3 and AM manually e Preset stations are erased when the power supply to the memory circuit is interrupted for example during bat
27. ch your favorite programme type see page 12 1 2 3 POP M ROCK M EASY M 4 5 6 CLASSICS AFFAIRS VARIED To store your favorite programme types 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display PSM see page 20 CONTINUED ON THE NEXT PAGE PTY codes NEWS News AFFAIRS Topical programmes expanding on current news or affairs INFO Programmes which impart advice on a wide variety of topics SPORT Sport events EDUCATE Educational programmes DRAMA Radio plays CULTURE Programmes on national or regional culture SCIENCE Programmes on natural science and technology VARIED Other programmes like comedies or ceremonies POP M Pop music ROCK M Rock music EASY M Easy listening music LIGHT M Light music CLASSICS Classical music OTHER M Other music WEATHER Weather information FINANCE Reports on commerce trading the Stock Market etc CHILDREN Entertainment programmes for children SOCIAL Programmes on social activities RELIGION Programmes dealing with any aspect of belief or faith or the nature of existence or ethics PHONE IN Programmes where people can express their views either by phone or in a public forum TRAVEL Programmes about travel destinations package tours and travel ideas and opportunities LEISURE Programmes concerned with recreational activities such as gardening cooking
28. d hold TP RDS Traffic Programme Radio Data System for more than 1 second Each time you press and hold the button Network Tracking Reception modes change as follows RDS gt Mode 1 Mode 2 Mode 3 REG indicator AF indicator Mode 1 The AF indicator lights up but the REG indicator does not Network Tracking Reception is activated with Regionalization set to off Switches to another station within the same network when the receiving signals from the current station become weak e In this mode the programme may differ from the one currently received Mode 2 Both the AF indicator and the REG indicator light up Network Tracking Reception is activated with Regionalization set to on Switches to another station within the same network broadcasting the same programme when the receiving signals from the current station become weak Mode 3 Neither the AF indicator nor the REG indicator lights up Network Tracking Reception is deactivated ENGLISH ba H OH Z m 10 A The same programme can be received on different frequencies Programme 1 broadcasting on frequency A Programme 1 broadcasting on frequency E Programme 1 broadcasting on frequency B B chs 1 broadcasting on frequency C Programme 1 broadcasting on frequency D Using Standby Reception Standby Reception allows the unit to switch temporarily to your favorite program
29. e You can eject the CD even when the unit is turned off Saco a a ce o On Sal Fi LAI A i r 7 L Al The CD IN indicator lights up AEA Total playing time of Total track number of the inserted disc the inserted disc Elapsed playing _ Current track time Note on One Touch Operation When a CD is already in the loading slot pressing CD turns on the unit and starts playback automatically 14 Locating a track or a particular portion on a CD To fast forward or reverse the track Press and hold gt A while playing a CD to fast forward the track Press and hold Lea Wv while playing a CD to reverse the track To go to the next tracks or the previous tracks Press gt A briefly while playing a CD to go ahead to the beginning of the next track Each time you press the button consecutively the beginning of the next tracks is located and played back Press L a xw briefly while playing a CD to go back to the beginning of the current track Each time you press the button consecutively the beginning of the previous tracks is located and played back To go to a particular track directly 7 8 1 12 9 10 zw cm Gam Gs 6 Press the number button corresponding to the track number to start its playback e To select a track number from 1 6 Press 1 7 6 12 briefly To select a track number from
30. e vehicle carefully Incorrect connection may cause serious damage to this unit 1 Connect the colored leads of the power cord to the car battery speakers and power aerial if any in the following sequence Black ground Yellow to car battery constant 12 V Red to an accessory terminal Blue with white stripe to power aerial 200 mA max Brown to cellular phone system For details refer to the instructions of the cellular phone Others to speakers OOOO 2 Connect the aerial cord 3 Finally connect the wiring harness to the unit Note If your vehicle does not have any accessory terminal move the fuse from the fuse position 1 initial position to fuse position 2 and connect the red lead A7 to the positive battery terminal The yellow lead A4 is not used in this case Raccordements typiques Vor dem AnschlieBen Die Verdrahtung im Fahrzeug sorgfaltig berpr fen Falsche Anschl sse k nnen ernsthafte Sch den am Ger t hervorrufen 1 Die farbigen Leitungen des Spannunsgversorgungskabels an der Autobatterie den Lautsprechern und dem Motorantenne sofern vorhanden in folgender Reihenfolge anschlie en Schwarz Erdung Gelb an Autobatterie konstant 12 V Rot an Zubeh ranschlu klemme Blau mit wei em Streifen an Motorantenne max 200 mA Braun an Mobiltelefon Weitere informationen entnehmen Sie bitte der Bedienungscanleitung des Mobiltelefons Andere an Lautspr
31. echer 2 Das Antennenkabel anschlie en 3 Die Kabelb ume am Ger t anschlie en Hinweis Verf gt Ihr Fahrzeug nicht ber eine Zubeh ranschlu klemme die Sicherung von der 1 Sicherungsposition Erstposition in die 2 Sicherungsposition versetzen die rote Leitung A7 an der Batterieanschlu klemme anschlie en e Die gelbe Leitung A4 wird in diesem Fall nicht verwendet Avant de commencer la connexion verifiez attentivement le c blage du vehicule Une connexion incorrecte peut endommager s rieusement l appareil 1 Connectez les fils de couleur du cordon d alimentation a la batterie de la voiture aux enceintes et l antenne automatique s il y en a une dans l ordre suivant Noir a la masse Jaune a la batterie de la voiture 12 V constant Rouge la prise accessoire Bleu avec bande blanche l antenne automatique 200 mA max Marron un syst me de t l phone cellulaire Pour les d tails se r f rer aux instructions du t l phone cellulaire Autres aux enceintes 2 Connectez le cordon d antenne 3 Finalement connectez le faisceau de fils l appareil Remarque Si votre v hicule ne poss de pas de borne accessoire d placez le fusible de la position de fusible 1 position originale la position de fusible 2 et connectez le fil rouge A7 la borne positive de la batterie e Le fil jaune A4 n est pas utilis dans ce cas ONLY FOR KD S811R NUR F R KD
32. f r den Einbau und Anschlu Die folgenden Teile werden zusammen mit diesem Ger t geliefert Nach ihrer berpr fung die Teile richtig einsetzen Sleeve Halterung Manchon Liste des pi ces pour l installation et raccordement Les pieces suivantes sont fournies avec cet appareil Apres verification veuillez les placer correctement Trim plate Frontrahmen Plaque d assemblage Lock nut M5 Sicherungsmutter M5 Ecrou d arr t M5 Washer ob Unterlegscheibe 5 Rondelle 05 o Qp Ai SC Rubber cushion Gummipuffer Amortisseur en caoutchouc Mounting bolt M5 x 20 mm Befestigungsschraube M5 x 20 mm Boulon de montage M5 x 20 mm KH ELECTRICAL CONNECTIONS ELEKTRISCHE ANSCHL SSE RACCORDEMENTS ELECTRIQUES To prevent short circuits we recommend that you disconnect the battery s negative terminal and make all electrical connections before installing the unit If you are not sure how to install this unit correctly have it installed by a qualified technician Note This unit is designed to operate on 12 V DC NEGATIVE ground electrical systems If your vehicle does not have this system a voltage inverter is required which can be purchased at JVC IN CAR ENTERTAINMENT dealers Replace the fuse with one of the specified rating If the fuse blows frequently consult your JVC IN CAR ENTERTAINMENT dealer If noise is a problem This unit incorporates a noise filter in the powe
33. fishing etc JAZZ Jazz music COUNTRY Country music NATION M Current popular music from another nation or region in that country s language OLDIES Classic pop music FOLK M Folk music DOCUMENT Programmes dealing with factual matters presented in an investigative style ENGLISH 11 ba 2 Oo Z m 12 A 2 Select PTY SRCH search if not shown on the display Select one of twenty nine PTY codes See page 11 Selected code name appears on the display If the code already stored in memory is selected it will flash on the display Press and hold the number button for more than 2 seconds to store the PTY code selected into the preset number you want 8 I nm 12 Em ae BEE En The selected code name will flash on the display Finish the setting To search your favorite programme type 1 Press and hold PTY programme type for more than 1 second while listening to an FM station The last selected PTY code appears Ong AM LU 1 M 2 Select one of PTY codes stored in preset number buttons 1 to 6 7 8 9 10 n Ce Ce Ex When ROCK M is stored in preset number button 2 PTY search for your favorite programme starts after 5 seconds If there is a station broadcasting a programme of the same PTY code you selected that station is tuned in If there is
34. he main unit Functions as the BAND button while listening to the radio Each time you press the button the band changes Does not function as the PROG DISC button Functions as the PRESET button while listening to the radio Each time you press the button the preset station number increases and the selected station is tuned in e Does not function as the DISC button Functions the same as the control dial on the main unit Note This button does not function for the preferred settings mode adjustment Selects the sound mode Each time you press SCM Sound Control Memory the mode changes Selects the source Each time you press FUNC function the source changes Searches stations while listening to the radio Fast forwards or reverses the track if pressed and held while listening to a CD Skips to the beginning of the next tracks or goes back to the beginning of the current or previous tracks if pressed briefly while listening to a CD What appears to be trouble is not always serious Check the following points before calling a service center Symptoms TROUBLESHOOTING Causes Remedies CD cannot be played back CD is inserted upside down ENGLISH Insert the CD correctly CD sound is sometimes interrupted Sound is sometimes interrupted You are driving on rough roads Stop playing CD while driving on rough roads The disc is scratc
35. hed Change the disc Connections are incorrect Connections are incorrect Check the cords and connections Check the cords and connections Sound cannot be heard from the speakers The volume is turned to the minimum level Adjust it to the optimum level Connections are incorrect Check the cords and connections e SSM Strong station Sequential Memory automatic preset does not work Signals are too weak Store stations manually e Static noise while listening to the radio The antenna is not connected firmly Connect the antenna firmly NO DISC appears on the display No CD is inserted Insert a CD correctly D CD cannot be ejected CD is locked Unlock the CD see page 16 CD can be neither played back nor ejected The unit may function incorrectly Press and hold both 1 ATT and amp at the same time for several seconds Be careful not to drop CD when itis ejected D This unit does not work at all The built in microcomputer may function incorrectly due to noise etc Press and hold both SEL and WATT at the same time for several seconds to reset the unit The clock setting and preset stations stored in memory are erased See page 2 25 ba 2 mr 0 Z m 26 g i MAINTENANCE Handling CDs This unit has been designed only to reproduce the CDs bearing the following marks
36. ing and to obtain the best possible performance from the unit CONTENTS How to reset your unt 2 LOCATION OF THE BUTTONG 4 Control panel s sssessesssieseeesieesrerreisrrerense 4 BASIC OPERATIONS ak 5 Turning on the power 5 RADIO BASIC OPERATIONS 6 Listening to the radio u 6 Storing stations in Memory 7 Tuning into a preset station 8 RDS OPERATIONS ccceceeeeeeees 9 What you can do with RDS EON 9 Other convenient RDS functions and adjustments ee eeeeeeeeeeeeeeeteeeeeeteeeeeeee 12 CD OPERATIONS nisinsin 14 Playing RE RE 14 Locating a track or a particular portion on a Ee Fe ea Tu He 15 Selecting CD playback modes wee L Prohibiting CD ejection eeeeeeee 16 Note For security reasons a numbered ID card is provided with this unit and the same ID number is imprinted on the unit s chassis Keep the card in a safe place as it will help the authorities to identify your unit if stolen SOUND ADJUSTMENTS 17 Adjusting the sound 17 Using the Sound Control Memory SCM 17 Storing your own sound adjustments 18 OTHER MAIN FUNCTIONS 19 Setting the clock sses 19 Changing the general settings PSM 19 Detaching the control panel 22 REMOTE CONTROLLER oaa 23 With an optionally purchased remote controller only for KD S811R Installing the battery ee 23 Using
37. l will drop in a moment To resume the previous volume level press the button briefly again If you rotate the control dial clockwise you can also restore the sound To turn off the power Press and hold 1 ATT for more than 1 second Note When you use this unit for the first time set the built in clock correctly see page 19 CAUTION on Volume Setting CDs produce very little noise compared with other sources If the volume level is adjusted for the tuner for example the speakers may be damaged by the sudden increase in the output level Therefore lower the volume before playing a disc and adjust it as required during playback ENGLISH N Ted RADIO BASIC OPERATIONS ba 2 oO Z m Ki RDS I HEHEHEHEHE O SI amp Listeni ng to the radio To stop searching before a station is received _ _ _ _ Yt Dress the same button you have pressed for searching You can use either automatic searching or manual searching to tune into a particular station Searching a station manually Manual search Searching a station automatically Auto search 1 Select the band AM FM1 3 I select the band AM FM1 3 EN Cem lee gt FM1 FM2 FM3 Note 7 ei This receiver has three FM bands FM1 FM2 P H d d d S FM3 You can use any one of them to listen to an
38. ling d str len s s teeseen mm IMPORTANT FOR LASER PRODUCTS Precautions 1 CLASS 1 LASER PRODUCT 2 DANGER Invisible laser radiation when open and CLASS 1 interlock failed or defeated Avoid direct exposure to LASER PRODUCT zeam 3 CAUTION Do not open the top cover There are no user serviceable parts inside Leave all servicing to qualified service personnel Caution 4 CAUTION This CD player uses invisible laser This product contains a laser component radiation and is equipped with safety switches to of higher laser class than Class 1 prevent radiation emission when unloading CDs It is dangerous to defeat the safety switches 5 CAUTION Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure How to reset your unit Press and hold both the SEL select and 1 ATT standby on attenuator buttons at the same time for several seconds This will reset the built in microcomputer d UATT Standby On Attenuator SEL Select Notes e Your preset adjustments such as preset channels or sound adjustments will also be erased e Ifa CD is in the unit it will eject when you reset the unit Pay attention not to drop the CD Thank you for purchasing a JVC product Please read all instructions carefully before operation to ensure your complete understand
39. llowance Grounding System Negative ground Allowable Operating Temperature 0 C to 40 C Dimensions W x H x D Installation Size 182 mm x 52 mm x 150 mm Panel Size 188 mm x 58 mm x 14 mm Mass 1 3 kg excluding accessories Design and specifications subject to change without notice 27 Having TROUBLE with operation Please reset your unit Refer to page of How to reset your unit Haben Sie PROBLEME mit dem Betrieb Bitte setzen Sie Ihr Ger t zur ck Siehe Seite Zur cksetzen des Ger ts Vous avez des PROBLEMES de fonctionnement Reinitialisez votre appareil R f rez vous a la page intitul e Comment r initialiser votre appareil Hebt u PROBLEMEN met de bediening Stel het apparaat terug Zie de pagina met de paragraaf Het apparaat terugstellen dB EN GE FR NL 1100HISFLEJES KD S811R KD S713R KD S711R SE Installation Connection Manual KS Einbau Anschlu anleitung Manuel d installation raccordement GET0013 003A E ENGLISH e This unit is designed to operate on 12 V DC NEGATIVE ground electrical systems INSTALLATION IN DASH MOUNTING 1100HISFLEJES EN GE FR DEUTSCH FRAN AIS e Dieses Ger t ist f r einen Betrieb in elektrischen Anlagen mit Cet appareil est con u pour fonctionner sur des sources de 12 V Gleichstrom und Erdung ausgelegt EINBAU IM ARMATURENBRETT courant continu de 12 Va masse NEGATIVE seulement INSTALLATION MONTAGE DANS LE TABLEAU
40. me PTY Programme Type and Traffic Announcement TA from the current source another FM station and CD e Standby Reception will not work if you are listening to an AM station TA Standby Reception RDS When you press TP RDS while listening ml to an FM station the TP indicator is lit during reception of a TP Traffic Programme station and the TA standby mode is engaged When the station being received is not a TP station the TP indicator flashes Press Kl A or 4 lt 4W to engage the TA standby mode SEARCH appears on the display and TP station search starts When a TP station is tuned in the TP indicator is lit E If you are listening to a CD and wish to listen to a TP station press TP RDS to enter the TA standby mode The TP indicator lights up If a traffic programme starts broadcasting while the TA standby mode is active TRAFFIC appears and the playback source changes to the FM band The volume increases to the preset TA volume level see page 13 and the traffic programme can be heard To deactivate the TA standby mode press TP RDS again PTY Standby Reception a When you press PTY while listening to an FM station the PTY indicator is lit during reception of a PTY station and the PTY standby mode is engaged The selected PTY name stored on page 11 flashes for 5 seconds e When the station being received is not a PTY station the PTY indicator flashes Press PPA A or 44 to engage the PT
41. n Verst rker Die Anschlu klemmen am Ausgang dieses Ger t an den Anschlu klemmen des Eingangs des Verst rkers anschlie en Die Lautsprecher von diesem Ger t abtrennen und am Verst rker anschlie en Die Lautsprecherleitungen dieses Ger ts unbenutzt lassen Die Anschlu klemmen dieser nicht verwendeten Leitungen mit Isolierklebeband umwickeln siehe Abbidung oben um JVC Amplifier KD S811R KD S713R KD S711R Front speakers Vordere Lautsprecher Enceintes avant SOLO PARA KD S811R Podra conectar otro amplificador de potencia para los altavoces delanteros ONLY FOR KD S811R You can connect another power amplifier for front speakers D Connections Adding Other Equipment Anschl sse zum Hinzuf gen von anderer Ausr stung Raccordement pour ajouter d autres appareils Y connector not supplied with this unit Y Anschlu nicht mit diesem Ger t mitgeliefert Connecteur Y non fourni avec cet appareil To power aerial if any Zur Motorantenne sofern vorhanden Vers l antenne automatique s il y en a une Front speakers L b A u pe JVC Verst rker x Vordere Lautsprecher RP gt R JVC Amplificateur iq Enceintes avant SEULEMENT POUR KD S811R Vous pouvez connecter un autre amplificateur de puissance pour les enceintes avant Vous pouvez connecter un amplificateur pour am liorer votre syst me autoradio Connectez le fil de comm
42. nceled before you finish start from step 1 again 1 call up the sound mode you want to adjust See the left column for details xs Select BAS Bass TRE Treble or LOUD Loudness N 2 Adjust the bass or treble level or turn the loudness function ON OFF e See page 17 for details Repeat steps 2 and 3 to adjust the other items Press and hold SCM until the sound mode you have selected in step 1 flashes on the display Your adjustment made for the selected sound mode is stored in memory 6 Repeat the same procedure to store other sound modes To reset to the factory settings Repeat the same procedure and reassign the preset values listed in the table on the left column OTHER MAIN FUNCTIONS er Setting the clock You can also set the clock system either 24 hours or 12 hours 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display See page 20 2 Set the hour 1 Select CLOCK H if not shown on the display Adjust the hour m N 3 Set the minute Select CLOCK M Adjust the minute N 1 A set the clock system Select 24H 12H Select 24H or 12H m 2 N To check the current clock time while the unit is turned off press DISP display The power turns
43. ndicator 7 amp eject button 20 RDS indicators 8 KY gt A buttons AF EON REG TP PTY e Also functions as SSM buttons when pressed 21 SCM indicator together 22 LOUD indicator 9 SEL select button 23 Sound mode indicators 110 Remote sensor only for KD S811R BEAT SOFT POP 11 MO monaural button 24 CD indicator RND random button 25 Band indicators 12 Number buttons FM1 FM2 FM3 113 TP traffic programme AM RDS radio data system button 26 Main display 14 PTY programme type button 27 CD IN indicator SCM sound control memory button LAJ control panel release button BASIC OPERATIONS LICE CBT LDL s Hej m fei Gel Turning on the power 1 Turn on the power BEN Note on One Touch Operation When you select a source in step 2 below the power automatically comes on You do not have to press this button to turn on the power 2 Select the source Se To operate the tuner AM or FM see pages 6 13 To operate the CD player see pages 14 16 3 Adjust the volume To increase the volume To decrease the volume Volume level indicator Volume level appears 4 Adjust the sound as you want see page 17 To drop the volume in a moment Press WATT briefly while listening to any source ATT starts flashing on the display and the volume leve
44. on For KD S713R KD S711R Maximum Power Output Front 40 W per channel Rear 40 W per channel Continuous Power Output RMS Front 16 W per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 8 total harmonic distortion Rear 16 W per channel into 4 Q 40 Hz to 20 000 Hz at no more than 0 8 total harmonic distortion Load Impedance 4 Q 4 Q to 8 Q allowance Tone Control Range Bass 10 dB at 100 Hz Treble 10 dB at 10 kHz Frequency Response 40 Hz to 20 000 Hz Signal to Noise Ratio 70 dB Line Out Level Impedance 2 0 V 20 kQ load full scale Output Impedance 1 kQ TUNER SECTION Frequency Range FM 87 5 MHz to 108 0 MHz AM MW 522 kHz to 1 620 kHz LW 144 kHz to 279 kHz FM Tuner Usable Sensitivity 11 3 dBf 1 0 uV 75 Q 50 dB Quieting Sensitivity 16 3 dBf 1 8 uV 75 Q Alternate Channel Selectivity 400 kHz 65 dB Frequency Response 40 Hz to 15 000 Hz Stereo Separation 30 dB Capture Ratio 1 5 dB SPECIFICATIONS MW Tuner Sensitivity 20 uV Selectivity 35 dB LW Tuner Sensitivity 50 uV ENGLISH CD PLAYER SECTION Type Compact disc player Signal Detection System Non contact optical pickup semiconductor laser Number of channels 2 channels stereo Frequency Response 5 Hz to 20 000 Hz Dynamic Range 96 dB Signal to Noise Ratio 98 dB Wow and Flutter Less than measurable limit GENERAL Power Requirement Operating Voltage DC 14 4 V 11 V to 16 V a
45. orte fusible Zur Motorantenne sofern vorhanden Vers l antenne automatique s il y en a une Left speaker rear Linker Lautsprecher hinten Enceinte gauche arri re o im Sicherungsblock zum Fuse block 777 KM Sicherungsblock Porte fusible To cellular phone system Zur Moblitelephon A un syst me de t l phone cellulaire A Right speaker rear Rechter Lautsprecher hinten Enceinte droit arri re PRECAUTIONS on power supply and speaker connections e DO NOT connect the speaker leads of the power cord to the car battery otherwise the unit will be seriously damaged e Connect the black lead ground yellow lead to car battery constant 12 V and red lead to an accessory terminal correctly BEFORE connecting the speaker leads of the power cord to the speakers check the speaker wiring in your car If the speaker wiring in your car is as illustrated in Fig 1 and Fig 2 below DO NOT connect the unit using that original speaker wiring If you do the unit will be seriously damaged Redo the speaker wiring so that you can connect the unit to the speakers as illustrated in Fig 3 If the speaker wiring in your car is as illustrated in Fig 3 you can connect the unit using the original speaker wiring in your Car If you are not sure of the speaker wiring of your car consult your car dealer e VORSICHTSMASSREGELN beim Anschlie en der Stromversorg
46. ot to damage the connectors on the back of the control panel and on the panel holder ba 2 mr Z m Detaching the control panel Before detaching the control panel be sure to turn off the power 2 Press the right side of the control 1 Unlock the control panel panel to fix it to the panel holder Note on cleaning the connectors If you frequently detach the control panel the connectors will deteriorate To minimize this possibility periodically wipe the connectors with a cotton swab or cloth moistened with alcohol being careful not to damage the 3 Put the detached control panel into connectors the provided case Connectors 22 REMOTE CONTROLLER Preparing the remote controller With an optionally purchased remote controller only for KD S811R We recommend that you use remote controller RM RK31 with your unit The followings are the instructions for using RM RK31 Before using the remote controller Aim the remote controller directly at the remote sensor on the main unit Make sure there is no obstacle in between Remote sensor Do not expose the remote sensor to strong light direct sunlight or artificial lighting Installing the battery When the controllable range or effectiveness of the remote controller decreases replace the battery 1 Remove the battery holder 1 Push out the battery
47. r circuit However with some vehicles clicking or other unwanted noise may occur If this happens connect the unit s rear ground terminal see connection diagram to the car s chassis using shorter and thicker cords such as copper braiding or gauge wire If noise still persists consult your JVC IN CAR ENTERTAINMENT dealer For KD S811R Maximum input of the speakers should be more than 45 W at the rear and 45 W at the front with an impedance of 40210809 For KD S713R KD S711R Maximum input of the speakers should be more than 40 W at the rear and 40 W at the front with an impedance of 4 Q to 8 Q Be sure to ground this unit to the car s chassis The heat sink becomes very hot after use Be careful not to touch it when removing this unit Heat sink Abstrahlblech Dissipateur de chaleur Zur Vermeidung von Kurzschl ssen empfehlen wir da Sie den negativen Batterieanschlu abtrennen und alle elektrischen Anschl sse herstellen bevor das Ger t eingebaut wird Sind Sie sich ber den richtigen Einbau des Ger ts nicht sicher lassen Sie es von einem qualifizierten Techniker einbauen Hinweis Dieses Ger t ist f r eine Betrieb in elektrischen Anlagen mit 12 V Gleichstrom und Erdung ausgelegt Verf gt Ihr Fahrzeug nicht ber diese Anlage ist ein Spannungsinverter erforderlich der bei JVC Autoradioh ndler erworben werden kann Die Sicherung mit einer der entsprechenden Nennleistung ersetzen Brennt die
48. s des fils qui ne sont PAS utilises avec de la bande isolante nn Amplifier Verst rker Amplificateur You can connect an amplifier to upgrade your car stereo system e Connect the remote lead blue with white stripe to the remote lead of the other equipment so that it can be controlled through this unit e For amplifier only Connect this unit s line out terminals to the amplifier s line in terminals Disconnect the speakers from this unit connect them to the amplifier Leave the speaker leads of this unit unused Cover the terminals of these unused leads with insulating tape as illustrated above Rear speakers pi Hintere Lautsprecher Enceintes arri re JVC Amplifier LE re j JVC Verst rker RP gt o JVC Amplificateur Signal cord not supplied with this unit Einzelleitung nicht mit diesem Gerat mitgeliefert Cordon de signal non fourni avec cet appareil LINE OUT Remote lead Fernbedienungsleitung Fil d alimentation a distance Remote lead Blue with white stripe Fernbedienungsleitung Blau mit wei em Streifen Fil d alimentation a distance Bleu avec bande blanche Sie k nnen einen Verst rker anschlie en Ihre Autostereoanlage zu erweitern e Schlie en Sie das Fernbedienungskabel blau mit wei em Streifen an das Fernbedienungskabel des anderen Ger ts an so da es ber dieses Ger t gesteuert werden kann e Nur f r de
49. ter le boulon de montage sur l arri re du corps de l appareil puis passer l amortisseur en caoutchouc sur l extremite du boulon 6 R alisez les connexions lectriques 7 Faire glisser l appareil dans le manchon jusqu ce qu il soit verrouill 8 Attachez la plaque d assemblage de facon que la projection de la plaque d assemblage soit fix e sur le c t gauche de l appareil 9 Remonter le panneau de commande Handle 3 Griffe Poign e Lock Plate Arretierplattchen Slot Plaque de verrouillage Schlitz Sleeve Halterung Fente Fuse Sicherung Fusible Manchon Sleeve J Halterung Manchon Trim plate Frontrahmen Plaque d assemblage Amortisseur en Dashboard Armaturenbrett Tableau de bord Rubber cushion Gummipuffer caoutchouc Mounting bolt Befestigungsschraube Boulon de montage 6 See ELECTRICAL CONNECTIONS Siehe ELEKTRISCHE ANSCHL SSE R f rez vous RACCORDEMENTS ELECTRIQUES e When using the optional stay es Beim Verwenden der Anker Option e Lors de l utilisation du hauban en option Washer Unterlegscheibe Dashboard Armaturenbrett Tableau de bord Sleeve Halterung Manchon Fire wall Feuerwand Cloison Stay option Anker Option Hauban en option Lock nut Sicherungsmutter Ecrou d arr t Screw option Schraube Option
50. tery replacement If this occurs preset the stations again ba 2 Z m Ex Storing an FM station of 88 3 MHz into the preset number 1 of the FM1 band 1 Select the FM band FM1 3 you want to store FM stations into in Tuning into a preset station this example FM1 a Each time you press the button the FM You can easily tune into a preset station band changes as follows Remember that you must store stations first If you have not stored them yet see Storing stations in FM D memory on page 7 gt FM1 gt FM2 gt FM3 1 Select the band AM FM1 3 2 Tune into a station of 88 3 MHz gt FM1 gt FM2 gt FM3 Press gt A to tune in stations of higher AM frequencies Press L a to tune in 2 Select the number 1 6 for the preset stations of lower station you want frequencies 8 3 Press and hold the number button in COS eas Cs Cs this example 1 for more than 2 seconds 10 ST A d 217 I Sai Hid Pha P1 flashes for a few seconds 4 Repeat the above procedure to store other stations into other preset numbers What you can do with RDS EON RDS Radio Data System allows FM stations to send an additional signal along with their regular programme signals For example the stations send their station names as well as information about what type of programme they broadcast such as sports
51. the remote controller 24 TROUBLESHOOTING 44440 25 MAINTENANCE eceeeeeeeeeees 26 Handling CDs ssssessesnnenneennenneeesreeernereene 26 SPECIFICATIONS 2ceeeeeeeeeeees 27 BEFORE USE For safety Do not raise the volume level too much as this will block outside sounds making driving dangerous e Stop the car before performing any complicated operations Temperature inside the car If you have parked the car for a long time in hot or cold weather wait until the temperature in the car becomes normal before operating the unit ENGLISH ENGLISH LOCATION OF THE BUTTONS Control panel m sr AND a EON REG IE w a g 25 26 27 9 10 11 12 13 14 15 16 1 I ATT standby on attenuator button Display window 2 Control dial 17 Volume or audio level indicator 3 DISP display button Equalization Pattern indicator 4 AM button 18 Tuner reception indicators 5 CD button STEREO MONO 6 FM button 19 RND random i
52. tic clock adjustment follow the procedure below See also Changing the general settings PSM on page 19 1 Press and hold SEL select for more than 2 seconds so that one of the PSM items appears on the display 2 Press gt gt A or ea w to select AUTO ADJ 3 Rotate the control dial counterclockwise to select OFF Now automatic clock adjustment is canceled To reactivate clock adjustment repeat the same procedure and select ON in step 3 by rotating the control dial clockwise Note It takes about 2 minutes to adjust the time using the CT data So you should not change the station for more than 2 minutes continuously otherwise the clock time will not be adjusted ENGLISH 13 ba 2 0 Z m 10 RND H RDS Ya ua wa ala wa Een Playing a CD To stop play and eject the CD Press 4 1 Insert a disc into the loading slot CD play stops and the CD automatically ejects from The unit turns on the loading slot draws a CD and starts If you change the source to FM or AM the CD play CS playback automatically also stops without ejecting the CD this time bw a r Note Notes e Whena CD is inserted e Ifthe ejected disc is not removed for about 15 seconds upside down the CD the disc is automatically inserted again into the automatically ejects loading slot to protect it from dust CD play will not start this time A gil
53. ung und Lautsprecher e Die Lautsprecherleitungen des Netzkabels NICHT an der Autobatterie anschlieBen da sonst das Gerat schwer beschadigt wird PRECAUTIONS sur l alimentation et la connexion des enceintes e Die schwarze Leitung Erdung die gelbe Leitung zur Autobatterie konstant 12 V und die rote Leitung zur Zubeh ranschlu klemme richtig anschlie en e VOR dem Anschlie en der Lautsprecherleitungen des Spannunsgversorgungskabels an die Lautsprecher die Lautsprecherverdrahtung in Ihrem Auto berpr fen Ist die Lautsprecherverdrahtung wie unten in Fig 1 und Fig 2 abgebildet das Ger t NICHT mit der Originalverdrahtung der Lautsprecher anschlie en da sonst das Ger t schwer besch digt wird Die Lautsprecherverdrahtung erneuern so da Sie das Ger t an den Lautsprechern wie in Fig 3 abgebildet anschlie en k nnen Ist die Lautsprecherverdrahtung in Ihrem Auto wie in Fig 3 abgebildet k nnen Sie das Ger t mit der Originalverdrahtung der Lautsprecher in Ihrem Auto anschlie en Sind Sie sich ber die Lautsprecherverdrahtung in Ihrem Auto nicht sicher wenden Sie sich an Ihren Autoh ndler NE CONNECTEZ PAS les fils d enceintes du cordon d alimentation a la batterie sinon l appareil serait serieusement endommage Connectez correctement le fil noir a la masse le fil jaune a la batterie de la voiture 12 V constant et le fil rouge a la prise accessoire
54. ve Note Be sure to keep the handles for future use after installing the unit 4 Install the sleeve into the dashboard After the sleeve is correctly installed into the dashboard bend the appropriate tabs to hold the sleeve firmly in place as illustrated 5 Fix the mounting bolt to the rear of the unit s body and place the rubber cushion over the end of the bolt 6 Do the required electrical connections 7 Slide the unit into the sleeve until it is locked 8 Attach the trim plate so that the projection on the trim plate is fixed to the left side of the unit 9 Attach the control panel 7 Vor dem Einbau Dr cken Sie LA Freigabe der Bedienungsblenda um die Arretierung der Bedienungsblende zu l sen sofern diese bereits angebracht ist Bei der Auslieferung ab Werk ist die Bedienungsblende im Etui verpackt 2 Den Frontrahmen herausnehmen 3 Die Halterung nach dem Entriegeln der Halterungensperren abnehmen Das Ger t aufstellen Hinweis Beim Aufstellen des Ger ts darauf achten daB die Sicherung auf der R ckseite nicht besch digt wird Die 2 Griffe zwischen dem Ger t und der Halterung wie abgebildet einstecken und die Halterungensperren entriegeln Die Halterung entfernen Hinweis Sicherstellen da die Griffe f r k nftigen Gebrauch nach dem Einbau des Ger ts aufbewahrt werden 4 Die Halterung im Armaturenbrett einbauen Nach dem korrekten Einbau der Halterung im Armaturenbrett
Download Pdf Manuals
Related Search