Home

JVC DM-JV600U User's Manual

1. 0081 enc hardware video input error recover The video input signal is abnormal Confirm the connection between HD SDI IN terminal and connected device Confirm the signal input into HD SDI IN terminal 0084 enc hardware audio input error 0085 enc hardware audio input error recover The audio input signal is abnormal Confirm the connection between AES EBU IN terminal and con nected device Confirm the signal input into AES EBU IN terminal 0088 enc hardware resync Resync process has occured when syn chronizing to video input signal Confirm the connection between HD SDI IN terminal and connected device Frequent reconnection of the connector may cause the error Confirm the signal input into HD SDI IN terminal lt q Error code Error code Error content Cause of error Troubleshooting 0002 parameter error The content of the internal parameter default parameter and others is ab normal 0008 FAN stop error 0009 FAN stop error recover 001a FAN stop timeout error FAN operation is abnormal 0013 hardware fatal error The hardware of this unit is abnormal 0014 software fatal error The software of this unit is abnormal 0015 system boot fatal error The restart of this unit is abnormal 0044 video frame interrupt timeout error 0045 video frame interrupt timeout error recover The interruption of video frame ha
2. HDTV ENCODER DM JV600U INSTRUCTIONS For Customer Use Enter below the Serial No which is located on the rear of cabinet Retain this information for future reference Thank you for purchasing this JVC product Model No DM JV600U Before operating this unit please read the instructions carefully to ensure the best possible performance Serial No This instruction book is made from 100 recycle paper LSTO159 001C IMPORTANT SAFEGUARDS 1 Read all of these instructions 2 Save these instructions for later use 3 All warnings on the product and in the operating instructions should be adhered to 4 Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 5 Do not use attachments not recommended by the appliance manufacturer as they may cause hazards 6 Do not use this appliance near water for example near a bathtub washbowIl kitchen sink or laundry tub in a wet basement or near a swimming pool etc 7 Do not place this appliance on an unstable cart stand or table The appliance may fall a causing serious injury to a child or adult and serious damage to the appliance Use only with a cart or stand recommended by the manufacturer or sold with the appliance Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer An appliance and cart combinat
3. Main Menu Configuration Menu Main Menu Configuration Menu Configuration Menu Operate Param Menu Configuration Menu Initial Param Menu Initial Param Menu gt Control Mode Local Initial Param Menu gt Control Mode Local Initial Param Menu gt Control Mode Remote Memo The Operate Param Menu setting will be reflected in the output even if Save amp Reboot is not executed Initial Param Menu gt Save amp Reboot Do not turn off the power switch during Now Initializ ing display The setting value may not be saved or may return to default setting HDTV ENCODER DM JV600U Restoring the Default Menu Setting Value Each feature that has been set using the menu can be returned to default factory setting All the menu settings return to default Operation Flow Chart Display Flow Chart Press the ENTER button Main Menu Main Menu screen will be displayed Configuration Menu 2 Press the A V buttons vain Menu Select the Configuration Menu Configuration Menu 3 Press the ENTER button Ponticueien wment Configuration Menu screen will be displayed Operate Param Menu 4 Press the A V buttons Configuration Menu Select the Default amp Reboot gt Default amp Reboot Now Initializing dis play i S amp nt ol S es 2 Do not turn off the Q Pr he ENTER button 5 psa l l Configuration Menu power switch during Sy Execution co
4. e When mounting this unit to rack mount the L shape bracket to both ends of the rack to ensure strength e When mounting to the rack mount it in the way such that this unit will not protrude out from the rack The depth of the rack should be at least 700 mm Remove the foot 2 Remove the front panel EIA Rack 3 Mount this unit to rack using the supplied 4 screws Return the front panel to its original sta tus Do not remove the mounting bracket The mounting may become unstable due to loosen screws In addition if the mounting direction of the bracket is wrong it will be extremely dangerous as the bracket will not be properly mounted onto the rack 10 Menu Flow Chart The menu of this unit consists of 3 level of menus namely Main menu Sub menu and Setting items Display screen Menu ltem Main Menu Sub Menu Setting HDTV ENCODER DM JV600U e Video Rate e Asp Main Menu Configuration Menu e 82Pulldown e Audio Mode Configuration Menu Operate Param Menu e Audio Rate Setting of the encoding bit rate starting ES Page 12 Start method of encoding various parameters OO Operate Param Menu e Stop saving and reset of the menu item setting lids are possible NTER ii Configuration Menu A Control Mode e Start Mode Initial Param Menu i Moup e o e TS Rate i m T F Page 13 Video Mode
5. D A Initial Param Menu e Audio Format kg e Audio Input Main Menu O Audio ExDelay S Status Menu F on M e Audio Enable Configuration Menu PSI Enable Current operation status and error log can gt Save amp Reboot e PAT TS ID be confirmed PMT PID AD Page 16 7 PCR PID A O How to Change Menu Setting e Video PID OO e Audio PID Ly SZ Configuration Menu e Video Stream ID e Audio Stream ID gt Default amp Reboot e Video Copyright Main Menu e Video Org Copy Administration Menu I Page 17 e Audio Copyright Restoring the Default Menu Setting Value e Audio Org Copy Administrator menu Password is required eda Status Menu Page 22 Using the Administration P j Status Running ES Page 20 ry 7 Checking Operation Status LY Vy Status Menu Log ES Page 21 Checking Error Log Configuration Menu Default setting Operate Param Menu Video Rate 9000kbps Set the bit rate of the encoded video signal to The setting value can be set in 10 kbps step 20000kbps to A0000kbps Asp W When the Video Mode Set the horizontal size of the encoded video signal item inthe menu is set 16 9 1920 x 1080 Encode with 1920 H x 1080 V size to 10801 16 9 1440 x 1080 Encode with 1440 H x 1080 V size 16 9 1920 x 1080 16 9 1280 x 1080 Encode with 1280 H x 1080 V size 16 9 1440 x 1080 16 9 1280 x 720 Encode with 1280 H x 7
6. Display the setting sta tus of reference syn chronized signal Display the setting sta tus of encoding of video signal Display the setting sta tus of encoding of au dio signal Indicate that sub menu is present Indicate executable menu items or alterable menu setting value Indicate that sub menu is not present O g 2 ad Q S U xe g A H S Rear Panel AC IN Power input terminal 43 AES EBU IN Audio signal input terminal Use the power cord supplied to connect to an AC BNC 120 V 50 Hz 60 Hz outlet Input terminal for digital audio signal PCM or Dolby Digital bitstream Connect to the digital au 2 i ignal i rminal BN HD SDI IN Video signal input terminal BNC dio signal output terminal of the device outputting Input terminal for HD serial digital video signal This terminal also receives audio signal when audio signal audio signal is embedded into HD serial digital video signal A When using the audio signal input terminal Connect to the HD serial digital video signal out set the audio input item in the Configuration put terminal of the device outputting video signal Menu to AES EBU Page 13 Configuration Menu HD SDI MONI OUT Video signal output terminal BNC e For the audio signal to be input to AES EBU Output terminal for through HDTV serial digital IN terminal use the 48 kHz audio signal that video signal is synchronized with vide
7. E Do not place heavy objects or ride on this equipment Placing heavy object such as TV monitor or placing big ger object than this unit may cause injury as the object may become unbalanced and fall In addition the cover may deform due to the weight and the component inside may damage resulting in fire and electrical shock W Wipe this equipment using soft rags Wiping with thinner or benzene may dissolve or tarnish its surface For dirt that cannot be easily removed wipe using a neutral detergent diluted with water followed by wiping with a dry cloth Mi Do not place object filled with water vase flowerpot cup cosmetics and medicine etc It will result in fire and electrical shock if water is spilt into the equipment E Do not insert anything into the equipment It will result in fire and electrical shock if metal or inflammable object is inserted from the ventilation hole Transportation W Turn off the power and unplug the power cord from AC outlet before transportation This may cause damage to power cord fire or electrical shock E When moving or carrying the main unit do no hold it by the front panel as this can easily be detached by pulling it toward you If moving or carrying the main unit while holding it by the front panel the main unit might be caused to fall as a result of the front panel becoming detached Such an in cident may cause unexpected injury or a malfunction of the main unit Saving Energy
8. NE PAS OUVRIR LE BOITER AUCUNE PIECE INTERIEURE N EST A REGLER PAR LUTILISATEUR SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME Le symbole de l clair a l int rieur d un triangle equilat ral est destin a alerter lutilisateur sur la pr sence d une tension dangereuse non isol e dans le bo tier du produit Cette tension est suffisante pour provoquer l lectrocution de personnes Le point d exclamation a l int rieur d un triangle quilat ral est destin a alerter l utilisateur sur la presence d op rations d entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d instructions the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE This unit should be used with 120 V AC only CAUTION To prevent electric shocks and fire hazards DO NOT use any other power source NOTE The rating plate Serial number plate is on the rear of the unit INFORMATION for USA This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual
9. 10 Menu Flow Chatt cccccscceseeeeeees 11 Menu Setting inca sveceressinciesmcerveciousarcen 12 How to Change Menu Setting 16 Basic operation Restoring the Default Menu Setting Value sastsswandcnuseronecenestotesananeeas 17 Starting the Encoding ccceeee 18 Checking Operation Status 20 Checking Error Log ccccsseeeeeees 21 Using the Administration Menu 22 EN Or LOO orea eee Te 24 Setting the 3 2 Pulldown 26 Specifications cccceeeeeeeeeeeceeeeeeeees 27 Precautions Maintenance and operating environment E Do not store or use this equipment in the following envi ronments This will cause malfunctioning and damage e Locations beyond the allowable operating temperature range of 5 C and 40 C Locations beyond the allowable operating humidity level of 30 and 80 Near equipment that produces strong magnetic fields such as transformers or motors Near equipment that emits radio waves such as trans ceivers and mobile phones Locations with excessive dust and sand Locations that are subject to excessive vibration Locations prone to condensation Locations that emit radiation X rays or corrosive gases Handling W Do not stack up the equipment to prevent temperature within from rising E Do not stand this equipment vertically during use W Handle this equipment with care Do not subject it to physical shock
10. 20 V size 16 9 1280 x 1080 i When the Video Mode item in the menu is set to 720p 16 9 1280 x 720 3 2Pulldown Auto Set the 3 2 Pulldown OFF Auto Perform 3 2 Pulldown process automatically depends on the video signal OFF Does not perform 3 2 Pulldown process I Page 26 Setting the 3 2 Pulldown Audio Mode Stereo Set the channel mode of the audio encoded signal Single Stereo Encode with stereo mode Single Encode with single channel mode monaural Audio Rate WE When the Audio Mode Set the bit rate of the encoded audio signal item in the menu is set to Stereo 384kbps 256kbps 192kbps W When the Audio Mode item in the menu is set to Single 192kbps 128kbps 96kbps Start Start the encoding I Page 18 Starting the Encoding Stop Stop the encoding I Page 19 Stop the encoding manually Memo When the Audio Enable un der the Initial Param Menu screen is set to ON the up per limit value of Video Rate is When the Audio Format un der the Initial Param Menu screen is set as e MPEG TS Rate 700kbps e DD PT Dolby Digital Pass Through TS Rate 1000kbps When Audio Enable is set to OFF e TS Rate 200kbps Memo e The setting value of the Audio Rate item in the Operate Param Menu may change if Audio Mode setting is changed The setting of Audio Mode and Audio Rate un der the Operate Param Menu are disallowed when Audio Format under the Initial Param M
11. AN LTD JVC is a registered trademark in Japan the U S A the U K and many other countries 2004 VICTOR COMPANY OF JAPAN LIMITED Printed in japan LST0159 001C YAGOONA ALAH fNOO9AL ING
12. E Turn off the power to save energy when the equipment is not to be used for extensive periods of time Fan Replacement Fans mounted on the inner side of front panel and rear panel are subject to wear and tear Replace them every 3 years It is recommended to fill in the provided label with replacement date and paste it on this unit Consult your local JVC dealer when replacing fan Power Cord W Do not use the power cord supplied with this equipment on other devices Mi Do not place heavy object on the power cord nor placing the power cord under this unit This may cause damage to power cord fire or electrical shock li Use the power cord supplied to this unit Using the power cord with different voltage rating or dam aged power cord may cause fire or electrical shock Precautions on operation W The display of this unit may appear 2 seconds after turn ing on the power This is compliant to the regulation of high frequency of power supply and is not faulty Front Panel POWER oooooooo0oo0oo00000000000000000 f OO0O000000000000000000000000 TELEVISION ENCODER oooooooo0o000000000000000000 oooooo0o00000000000000000000 1 POWER Power switch Switch to turn on off power After this is switched to ON a Now Initializing will be displayed on the Display of front panel before normal screen is displayed Ra After turning on the power it may take 2 sec Memo onds before dis
13. L 1080i MP HL 720p MP H14L Video bit rate 9Mbps 40 Mbps 9Mbps 40 Mbps 9Mbps 40 Mbps 9Mbps 40 Mbps 1920 x 1080 59 94 Hz 1440 x 1080 59 94 Hz 1280 x 1080 59 94 Hz 1280 x 720 59 94 Hz lt Audio encoding gt MPEG 1 Layerll Stereo mode Single mode ISO IEC11172 3 Bit rate 384 kbps Bit rate 192 kbps 256 kbps 128 kbps 192 kbps 96 kbps Sampling 48 kHz Sampling 48 kHz Dolby Digital AC 3 Pass Channel 1 5 1 channel Through Sampling 48 kHz Bitrate 56 kbps to 640 kbps lt General gt E Interface RS 232C x1 Mi Power supply AC 120 V 50 Hz 60 Hz Mi Power consumption 7OW 0 6A W Allowable operating temperature 5 C to 40 C W Allowable storage temperature i Allowable operating humidity 20 C to 60 C 30 to 80 E Mass Approx 10 kg lt Accessories gt E Instruction Manual x1 lt Appearance gt 2 W Power cord 2 4 mM x1 unit mm 430 _ W Screws for mounting rack x4 hase 7 W Label x1 phonon j I za D 1 482 Dolby is a trademark of Dolby Laboratories 27 Specifications and appearance of this unit are subject to change for improvement without prior notice VICTOR COMPANY OF JAPAN LIMITED JVC is a registered trademark owned by VICTOR COMPANY OF JAP
14. Mode item is set to Auto in order to start the encoding automatically ES Page 13 Start Mode item Memo Passi The encoding can be man ually started or stopped if the Start Mode item in the menu is set to Manual ES Page 19 Start the encoding manually W Set the Start Mode item in the menu to Manual ac cording to the procedure on ES Page 18 Start the encoding automati cally Start the encoding manually Operation Flow Chart Press the ENTER button Main Menu screen will be displayed 2 Press the A V buttons Select the Configuration Menu and press the ENTER button 3 Press the A V buttons Select the Operate Param Menu and press the EN TER button 4 Press the A Y buttons Select the Start item and press the ENTER button 5 Press the ENTER button This starts the encoding lt q Stop the encoding manually Operation Flow Chart 1 Press the ENTER button Main Menu screen will be displayed 2 Press the A V buttons Select the Configuration Menu and press the ENTER button 3 Press the A V buttons Select the Operate Param Menu and press the EN TER button 4 Press the A Y buttons Select the Stop item and press the ENTER button 5 Press the ENTER button Stop the encoding Memo Display Flow Chart The encoding will stop if menu item has been changed dur ing manual encoding and gt Save amp Rebo
15. by status Indicates that fatal error has occurred IS Page 24 Error Log Checking Error Log E The error occurrence can be confirmed on the display Up to 64 occurrences can be stored Operation Flow Chart Display Flow Chart Press the ENTER button Main Went Main Menu screen will be displayed Configuration Menu 2 Press the A V buttons Main Menu Select the Status Menu Status Menu 3 Press the ENTER button Siena Wenn Status Menu screen will be displayed Status Running 4 Press the A Y buttons Select the Log item and press the ENTER button Status Menu Log 5 Press the A V buttons 00 FebO7 14 06 0001 The error log stored will be displayed system boot For detailed error log display read page 24 Error log gQ 2 V Q QO 2 e Y Q 21 Usingthe Administration Menu e The information regarding built in program or firmware version can be obtained from the Administration Menu In addition clock setting and the display brightness could be adjusted Please carry out the clock setting before use Display A V 4 Pbuttons E Examples of setting Setting the clock using the Administration Menu screen Operation Flow Chart Press the ENTER button Main Menu screen will be displayed 2 Press the A V buttons Select the Administration Menu 3 Press the ENTER button The Adm
16. en Dolby Digital bitstream is applied to AES EBU ter minal TS Format output could be obtained as this equip ment is Doloy Digital AC 3 1 5 1 channel pass through compliant In addition when PCM signal is applied to AES EBU termi nal it is possible to encode with MPEG 1 Layer IL Q Equipped with RS 232C terminal Each feature can be set or operated on the front panel with FL display Besides this unit can be remote controlled through the 9 pin connector on the rear panel Q 1U EIA size can be mounted to the rack Owing to the compact size design it can be mounted to the EIA rack Q 3 2 Pull down feature By converting to the SMPTE292M 1080i 720p standard HDTV digital serial video signal input movie film image that is 24 frame per one second can also be compressed to high quality using 3 2 Pull down feature Q Equipped with ASI output terminal Video recording is possible by connecting to D VHS digital video recorder from JVC that is equipped with ASI input ter minal Table of Contents _ Main Features cccceeeeseeeeeeeseeees 4 Intr ion troductio Table of Contents wrecestrrcccrsssstawsieccstcantis 5 Precautions seccencneccssdetencsenccensscaacoresness 6 gt Q Q 9 Q Q Front Panel oeeect onc zecqessseieneesetecqssansncenes 7 o Names and Functions Rear aC l sssini 8 lt Connecting veers ccaciscnedomana dicnenaedndesnienceuste 9 Preparation Mounting to a Rack sessen
17. enu is set as DD PT Dolby Digital Pass Through Configuration Menu Default setting Initial Param Menu Control Mode Local Set the operation mode of this unit Remote Local Set to this mode when operating this unit using the buttons on the front panel Remote Set to this mode when using RS 232C terminal on the rear panel to perform remote control of this unit Start Mode Auto Set the starting mode of encoding Manual Auto Start the encoding automatically Manual Start the encoding using the menu Ss Page 18 Starting the Encoding Sync Mode HD IN Set the synchronized signal that is the reference for encoding REF HD IN Synchronize with the input video signal REF Synchronize with the D1 signal input into REF IN terminal 2 on the rear panel TS Rate 10000kbps Set the TS bit rate to The setting value can be changed in 10 kbps step 21000kbps to 50000kbps Video Mode 1080i Set the Video Mode 720p Encode with 1080i 1080i format Encode with 720p 720p format Audio Format MPEG Setting the Audio Format DD PT MPEG Encoding with MPEG Layer II Dolby Digital Pass Through DD PT Dolby Digital Pass Through Dolby Digital bitstream will be output in TS Format Audio Input AES EBU Select the input audio signal EMB AES EBU Encode the audio signal input into AES EBU terminal 3 on the rear panel EMB Encode the Embedded audio signal input
18. inistration Menu screen will be displayed 4 Press the A V buttons Choose the Time item and press ENTER button 5 Press the A V lt gt Buttons lt P Buttons Move the cursor to the highlight the places when changes are to be made A V Buttons Change the values highlighted by the cursor Press the ENTER button once charges are made 22 ENTER ESC button button Display Flow Chart Main Menu Configuration Menu Main Menu Administration Menu Administration Menu Model DM JV600U Administration Menu gt Time 04 03 19 22 00 Administration Menu gt Time 04 03 19 22 0 At the selected places cursor will start to blink Administration menu Model Displays the model name serNo Displays the serial number Time Setting the Clock Year Month Day Hour Minute For the Year setting only the last 2 digits of the year will be used FL Brghtness Initial Setting 0 Setting the Display brightness Setting range is between 0 to 3 O Brightest setting Firm Displays the firmware version Ucode Displays the version of the u code Boot Displays the version of boot program MISC FPGA Displays the version of MISC FPGA STC FPGA Displays the version of STC FPGA I O PWB Displays the version of I O PWB I O VI PLD Displays the version of I O VI PLD I O AU PLD Displays the version of I O AU PLD Basic operation E 23 Error Log The
19. into HD SDI IN terminal on the rear panel Audio ExDelay 1Ims This setting is meant for compensating the delays to introduced when encoders are connected to 10ms external equipment to Denary Millisecond unit 500ms Setting value is 1 ms step variable Audio Enable ON Set whether to output audio signal or not OFF ON Output audio information OFF Does not output audio information Memo When input video sig nal is used in synchro nized mode video sig nal may not output for about 20 seconds due to switching of signal or reconnection of signal cable Memo Menu setting EA The setting value of the Video Rate item in the Op erate Param Menu may change if TS Rate setting value is changed Memo The setting value of the Asp item in the Operate Param Menu may change if Video Mode setting value is changed Memo This setting is only valid when Audio Format is set as DD PT Dolby Digital Pass Through Configuration Menu continued Default setting Initial Param Menu PSI Enable ON Set the PSI Program Specific Information to ON JFF OFF ON PAT and PMT will be output OFF PAT and PMT will not be output PAT TS ID 0001 Set the ID of PAT TS to PAT TS ID is the Transport Stream ID within PAT 0001 PAT Program Association Table is the correspondences to table of Program number and PMT PID FFFF PMT PID 0010 Set the PMT Packet ID to PMT Program Ma
20. ion should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn 8 Slots and openings in the cabinet and the back or bottom are provided for ventilation and to insure reliable operation of the appliance and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the appliance on a bed sofa rug or other similar surface This appliance should never be placed near or over a radiator or heat register This appliance should not be placed in a built in installation such as a bookcase unless proper ventilation is provided 9 This appliance should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company For appliance designed to operate from battery power refer to the operating instructions 10 This appliance system is equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding plug 11 For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unpl
21. l set the Sync Mode item in Tranfer speed 38 4 kbps the Configuration Menu to REF a bit a ES Page 13 Configuration Menu StopBit Has Flow Control None Cautions signal keep the phase difference of external ref erence synchronized signal and input video sig nal within 5H 1H D1signal cycle Phase zero is defined when the forth pin of D1 sig nal matches with first pin of input video signal e Input D1 signal before turning on the power of this unit The encoding may not start if D1 signal is not input when the power of this unit is turned on D e When using the external reference synchronized Connecting a One example of the basic systems using this unit is described below Turn OFF the power of all devices before connecting or disconnecting Synchronized Signal Generator HD SDI OUT AES EBU OUT _ Dolby Digital ENCODER DM JV600U RS 232C O O AES EBU IN C 6 ASI OUT ASI OUT Supplied power cord v J AC 120V 50 Hz 60 Hz Q DIGITAL VIDEO RECORDER SR VDA300U DVB ASI IN HDTV DECODER 100000 a l B n TN O 7 N m S iG i i Or Q
22. ly skip 24 frames in order to increase compression ratio Inverse Telecine 3 2 Pulldown auto setting For 3 2 Pulldown method the odd number frame is converted to 2 fields and the even num ber frame is converted to 3 fields With this feature it is possible to convert 2 frames into 5 fields which means that 24 frames could be converted into 60 fields _ Frame 1 1 Frame 2 2 Franie3 3 Frante 4 4 FranteS 5 ENCODER Frame When 3 2 Pulldown under the Operate Param Menu is set to AUTO input image signals will automatically be detected for 3 2 Pulldown processing information unnecessary fields will be discarded and only the original 24 frames will be encoded Specifications lt Input signal gt E Video input HD SDI IN x1 W Audio input AES EBU IN x1 W Synchronized input SMPTE292M common for 1080i 720p SMPTE299M Embedded Audio 800 mVp p 75 Q BNC unbalanced 1080i 1920 x 1080 frame frequency 29 97Hz 720p 1280 x 720 frame frequency 59 94Hz AES EBU 48 kHz sampling frequency synchronized with video signal 1 Vp p 75 Q BNC unbalanced SMPTE259M 800 mVp p 75 Q BNC unbalanced SMPTE292M common for 1080i 720p 800 mVp p 75 Q BNC unbalanced DVB ASI 188byte format packet mode 800 mVp p 75 Q BNC unbalanced REF IN x1 lt Output signal gt W Video output MONITOR OUT x1 ASI OUT x2 lt Video encoding gt MPEG 2 Video encoding profile ISO IEC 13818 2 1080i MP HL 1080i MP H
23. maaa au OE D AD O OC S X TumasET je es z mee ANALOG VIDEO OUT Y Pb Pr p3 O Speaker DIGITAL AUDIO IN Monitor VIDEO IN If there is interruption of input signal due to switching of HD SDI input signal or reconnection of signal cable video or audio signal may not output for about 20 seconds When AES EBU terminal is set and used as Audio Input i gt Page 13 terminal under the Initial Param Menu screen noise may be introduced into the audio signals if REF IN and HD SDI IN are stopped halfway In addition when the Dolby Digital bitstream is inputted from devices such as DVD player that is not synchro nized externally audio signal might be mixed with noise Use the following specified cables to avoid misoperation e HD SDI input cable 5C FB less than 10 m e HD SDI monitor output cable 5C FB less than 3 m This unit may output a full screen grey signal depends on the following input signal status e When the input video signal that is not compliant to SMPTE292M 1080i 720p is detected e f the phase difference against input video signal exceeds the range of 5H when synchronizing to external signal generator 9 Mounting to a Rack By making use of the hole on inner side of front panel this unit can be mounted to EIA rack z a ol
24. may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFER ENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION INFORMATION for Canada This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe A respecte toutes les exigences du Reglement sur le mat riel brouilleur de Canada Ces symboles ne sont utilis s qu aux Etats Unis AVERTISSEMENT POUR EVITER LES RISQUES D INCENDIE OU D ELECTROCUTION NE PAS EXPOSER L APPAREIL A L HUMIDITE OU A LA PLUIE Ce magnetoscope ne doit tre utilis que sur du courant alternatif en 120 V ATTENTION Afin d eviter tout resque d incendie ou d electrocution ne pas utiliser d autres sources d alimentation lectrique REMARQUE La plaque d identification num ro de s rie se trouve sur le panneau arri re de l appareil WARNING The battery used in the DM JV600U mu
25. nce to normal operation e If the appliance has been dropped or the cabinet has been damaged f When the appliance exhibits a distinct change in performance this indicates a need for service 18 When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Upon completion of any service or repairs to this appliance ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition AG 3125A SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in ATTENTION RISQUE D ELECTROCUTION NE PAS OUVRIR ATTENTION POUR EVITER TOUT RISQUE D ELECTROCUTION
26. nfirmation screen will be displayed Data Aabo O G NY Q 6 Press the ENTER button Setting to default of the menu setting and reboot of this unit will be performed Now Initializing HDTV ENCODER DM JV600U 17 Starting the Encoding There are 2 ways to start the encoding One is to start the encoding automatically and the other one is to start it manually by setting the menu 18 Display A V lt gt buttons O ie 0 ie fe ie ie ozo ie O ezo ie ie fe 0 ie 0 Start the encoding automatically Operation Flow Chart 1 Press the ENTER button Display the Initial Param Menu screen according to steps 1 5 on Page 16 How to Change Menu Setting 2 Press the A V buttons Select the Start Mode item and press the ENTER but ton 3 Press the A Y buttons Select the Auto and press the ENTER button 4 Press the ESC button 5 Press the ENTER button The encoding will start after the menu setting is saved and reboot of this unit is performed ENTER ESC button button Display Flow Chart Initial Param Menu gt Control Mode Local Initial Param Menu gt Start Mode Auto Initial Param Menu gt Start Mode Auto Initial Param Menu gt Save amp Reboot Now Initializing HDTV ENCODER DM JV600U Memo The default setting of the Start
27. o signal For checking the video signal inputted into HD eee _ SDI IN video signal input terminal on the rear It Dolby Digital Bitstream is inputted wher the Audio Format under the Initial Param panel Menu is set as MPEG loud sound might The output signal of HD SDI MONI OUT termi be produced Make sure that DD PT is set Memo nal that has not gone through re clock process before inputting Dolby Digital bitstream cannot be used as a formal SMPTE292M 1080i 720p standard HDTV serial digital i i video signal RS 232C Remote terminal D sub 9pin By connecting to the device for remote control con D ASI OUT TS output terminal BNC x2 trol of this unit can be performed externally TS output terminal Encodes and outputs the video signal inputted into HD SDI IN video signal W Pin assignment of RS 232C remote terminal input terminal and the audio signal inputted into AES EBU IN terminal 49 Pin No _ Signal name Content This terminal also outputs encoded audio signal 1 N C when audio signal is embedded into HD serial a 2 RxD Received data aigital video signal 3 TxD Transmitted data 2 REF IN D1 External reference 4 N C synchronized signal input terminal BNC 5 SG Ground Input external reference synchronized signal 6 N C For reference synchronized signal use the signal 7 N C that is compliant to SMPTE259M D1 5 NE 9 N C When using the external reference synchronized Memo signal input termina
28. ot has been excecuted Start the encoding manually once again Main Menu Configuration Menu Configuration Menu Operate Param Menu Operate Param Menu VideoRate 20000kbps Operate Param Menu gt Start Display Flow Chart Main Menu Configuration Menu Configuration Menu Operate Param Menu Operate Param Menu VideoRate 20000kbps Operate Param Menu gt Stop 19 S 2 X Q QO 2 e Y Q Checking Operation Status The operation status of this unit can be confirmed from the display 20 Display A V lt gt buttons POWER MULTI FORMAT HIGH DEFINITION TELEVISION ENCODER OO000000 DM JV6O0OO HDTV ENCODER ENTER ESC Operation Flow Chart 1 Press the ENTER button Main Menu screen will be displayed 2 Press the A V buttons Select the Status Menu 3 Press the ENTER button Status Menu screen will be displayed 4 Press the A V buttons Current operation status will be displayed by selecting the Status item ENTER ESC button button Display Flow Chart Main Menu Configuration Menu Main Menu Status Menu Status Menu Status Running Status Menu Status Running Status Menu Status Running Status Menu Status Status Menu Status Fatalerror Memo Indicate that the encoding is in process Indicate that the encoding is in stand
29. p Table is an index table that 0010 designates the various stream PIDs which to constituted the program 1FFE PCR PID 0010 Set the PCR Packet ID to PCR Program Clock Reference is clock data that is 0101 output periodically to It is used by the decoder to synchronize with internal TFFE clock for PLL synchronization Video PID 0020 Set the Video Packet ID to 0102 to IFFE Audio PID 0020 Set the Audio Packet ID to 0103 to 1FFE Video Stream ID EO Set the ID of Video PES stream to EO to EF 14 Configuration Menu continued Default setting Initial Param Meme Menu Audio Stream ID CoO Set the ID of Audio PES stream This setting is disabled to when Audio Format under the Initial Param Menu co screen is set as DD PT to Dolby Digital Pass Through DF Fixed as 0xBD Video Copyright OFF Set the copyright flag of Video PES ON OFF Set the copyright flag of Video PES to OFF ON Set the copyright flag of Video PES to ON Video Org Copy Org Set the Original Copy of Video PES Copy Org Set the Video PES to Original Copy Set the Video PES to Copy 2 Audio Copyright OFF Set the copyright flag of Audio PES ON OFF Set the copyright flag of Audio PES to OFF 2 ON Set the copyright flag of Audio PES to ON Q Audio Org Copy Org Set the Original Copy of Audio PES Copy Org Set the Audio PES to Original Copy Set the Audio PES to Copy Save amp Reboot Sa
30. play light up 2 ESC button Press this button when switching Display on the front panel from menu setting display to nor mal display Changing of the setting value in Menu item can also be cancelled by this button 3 ENTER button Press this button when switching Display on the front panel from normal display to menu set ting display Changing of the setting value in Menu item can also be confirmed by this button je Refer to page 16 for changing the menu Memo 4 A V lt 4 gt buttons Press this button to select menu item or change the setting value of menu item during menu set ting display 5 Display The operation status error content and menu item of this unit will be displayed t Following item About display POWER indicator Light up in green during operation 7 FAULT indicator Light up in orange when error occurs on this unit q About Display E Normal display HDTV ENCODER DM JV600U Press the A V buttons x DM JV60O0 HDTV ENCODER ENTER ESC Local Running SYN HD IN START Auto Press the A V buttons x V 1080i 20000kbps A MPEG 384kbps E Main Menu Main Menu Configuration Menu WE Sub Menu Configuration Menu gt Save amp Reboot Status Menu t Display the control set ting status of this unit Displays the current operation status Display the setting sta tus of how encoding will start
31. s timed out 0060 domino chip running error 0061 domino chip running error recover 0072 domino chip boot fatal error 0073 domino chip running fatal error The IC inside this unit is abnormal 00a0 enc software video input error 00a1 enc software video input error recover 00a2 enc software video running error 00a3 enc software video running error recover The process of the input stage of video signal is abnormal 00a8 enc software audio input error 00a9 enc software audio input error recover OO0aa enc software audio running error OOab enc software audio running error recover The process of the input stage of audio signal is abnormal This unit is abnormal Switch the power to OFF and turn on the power again Consult your local JVC dealer if the problem is still unsolved 25 lt 7 Q Setting the 3 2 Pulldown 26 Encoding image film material It is required to convert the video signal Pulldown in order to view the image recorded with 24 frames per second such as movie film on a system for HDTV video signal that is 30 frames per second 60 field used in TV broadcasting Normally HDTV VTR utilize 3 2 Pulldown Telecine method to achieve image signal conversion before recording on tape When this equipment is encoding signals which have been recorded with 3 2 Pulldown processing it is possible to encode by automatical
32. st be replaced by a JVC authorized service dealer only CAUTION Use of controls or adjustments or performance of proce dures other than those specified herein may result in haz ardous radiation exposure Note Place a cover on the terminal not in use Static may cause a malfunction or failure of the unit Thank you for purchasing this HDTV ENCODER DM JV600U If should be noted that it may be unlawful to re record pre recorded tapes records or discs without the con sent of the owner of copyright in the sound or video re cording broadcast or cable program and in any literary dramatic musical or artistic work embodied therein Prior to important video audio recording always perform a test recording to confirm that video audio is properly recorded Please note that we will not provide compensation for contents of video audio recording due to improper video audio recording caused by defects when using this equip ment Dolby is a trademark of Dolby Laboratories Main Features see Encoded to MPEG 2 ISO EC13818 2 Input SMPTE292M 1080i 720p standard HDTV digital se rial video signal encode it to MPEG 2 ISO IEC13818 2 and output as DVB ASI TS Transport Stream Q Supports SDI embedded Audio signal 2 channels Encodes SMPTE299M standard SDI embedded Audio sig nal 2 channels to MPEG 1Layer II ISO EC11172 3 and output as TS format Q Dolby Digital AC 3 pass through Compli ance Wh
33. stored error log can be displayed by performing the operation on page 21 Checking Error Log The error content is displayed by error code 24 lt q Display a b C 00 Feb07 14 06 0001 a Error log No d Error code system boot Error code e Error content b Error occurrence date c Error occurrence time For the error content with plenty of characters press the lt gt buttons to scroll the display The date and hour of this unit is adjusted to Green wich Mean Time GMT Error code Error content Cause of error Troubleshooting 0001 system boot Restart of this unit has been performed 0020 communication error The communication error caused by control device communication has occurred 0021 command parameter error The value of command and parameter created by control device communication is abnormal 0022 command busy This unit has received action command when it is busy Confirm the connection to external device Confirm the setting of external de vice 0040 sync input error 0041 sync input error recover The synchronized signal cannot be de tected 0050 sync no input timeout error The detection of the synchronized signal has timed out when this unit restarts Confirm the connection to external synchronized signal generator and the synchronized signal itself 0080 enc hardware video input error
34. ug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 12 Do not allow anything to rest on the power cord Do not locate this appliance where the cord will be abused by persons walking on it 13 Follow all warnings and instructions marked on the appliance 14 Do not overload wall outlets and extension cords as this can result in fire or electric shock 15 Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the appliance 16 Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 17 Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the appliance c If the appliance has been exposed to rain or water d If the appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the applia
35. ve the setting value of the menu and restart this unit Ss Page 18 Starting the Encoding Default amp Reboot Return the setting value of the menu to default and restart this unit I Page 17 Restoring the Default Menu Setting Value 15 How to Change Menu Setting a The various features of this unit can be set using the menu The setting value which is stored in the internal memory will reappear upon turning on the power E Example Remote control of this unit can be achieved by using the RS 232C terminal on the rear panel Configuration Menu l Initial Param Menu i Control Mode 4 Remote 16 Display A V 4 Pbuttons 0 0 0 ie ie ie Operation Flow Chart Press the ENTER button Main Menu screen will be displayed 2 Press the A V buttons Select the Configuration Menu 3 Press the ENTER button Configuration Menu screen will be displayed 4 Press the A V buttons Select the Initial Param Menu 5 Press the ENTER button Initial Param Menu screen will be displayed 6 Press the A V buttons Select the Control Mode item and press the ENTER button 7 Press the A V buttons Select the Remote and press the ENTER button 8 Press the ESC button Q Press the ENTER button Now Initializing ENTER ESC button button Display Flow Chart

JVC DM-JV600U User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents