Jura Capresso X90/X95 User's Manual
Contents
1. page 8 1 Drawing off powder 001186 page 9 Drawing off hot page 10 Drawing off steam page 11 Frothing up milk with the Profi Auto Cappuccino Caff Latte page 11 1 Frothing up a portion of milk page 11 2 Constant frothing up of milk page 11 3 Drawing off hot milk using the Profi Auto Cappuccino Caff Latte page 11 4 Drawing off cappuccino using the Profi Auto Cappuccino Caff Latte page 11 5 Controlling the temperature using the Profi Auto Cappuccino Caff Latte page 11 6 Cleaning of the Profi Auto Cappuccino Caff Latte page 12 Switching off page 13 Programmirig Te ret page XO 9 XO XO CO CO CO CO CO OO CO 12 12 12 12 12 m B 15 16 17 18 19 20 21 22 13 1 Programming powder quantity page 13 2 Programming coffee temperature page 13 3 Programming water quant2. page 14 11 Empty system irre ehe page CIC CO PL page zDecalcifylng e dee REM page Disposal itr he et Hte tee rua page Tips for a perfect coffee page e sabre page Problems eiin eneen aaa ee page Legal 1 8 page Technical specifications page 13 13 13 13 14 14 14 14 14 15 Important information for the user Thank you for choosing this Jura product Please study these instructions carefully before using your new machine and keep them in a safe place for easy reference in the future Should you require further information or should particular pro blems occur that are not dealt with in these operating instructions in sufficient detail for you then please ask your local dealer for the information you require or contact Jura Elektroapparate AG directly 1 Description This fully automatic espresso coffee machine impresses because of its user friendly operational mode and its ingenious technology In just one brewing process it can prepare 1 or 2 cups of excellent professional quality espresso coffee with guaranteed froth Be
3. Run the rinsing programme once or twice If the problem persists run cleaning programme Coffee flow is stopped after pre brewing Not enough coffee powder in the system Draw off one cup of coffee Grinder is extremely noisy Foreign element in grinder Proceed as described in chapter 14 5 21 Problem Cause Action Use full cream milk Clean frothing nozzle Clean Profi Auto Cappuccino Caff Latte as described in chapter 11 6 Not enough froth while frothing up milk Unsuitable milk type Frothing nozzle blocked Clean Auto Cappuccino If the above mentioned problems and or messages still persist please contact your dealer or get in touch directly with Jura Elektroapparate AG 21 Legal information These operating instructions contain all the information necessary for the correct use operation and maintenance of your espresso coffee machine Understanding and complying with the directions contained in these operating instructions are essential to ensure that the machine is utilised without risk and to ensure safety during operation and maintenance These operating instructions cannot cover all the possible ways in which this machine may be used We would like to further point out that the contents of these operat ing instructions in no way constitute a part of or alter any pre vious or existing contract agreement or legal relationship All ob ligation
4. After 10 minutes the warning lamp goes out By pressing the steam key anew the machine returns to stand by status for drawing off steam 13 9 Programming timer clock A programming of the timer clock is necessary if an auto matic switch on time is required m DISFLAV TIME W Press key By briefly pressing key or you can set the hours and then confirm by pressing key P m By briefly pressing key CP or you can set the minutes and then confirm by pressing key B m By pressing the CP button you can select the next phase or press the N button in order to leave the programming 13 10 Programming automatic switch on time A programming of the timer clock is necessary if an automatic switch on is needed 3 UNIT ON E Press key P m By briefly pressing key or you can set the hours and then confirm by pressing key P m By briefly pressing key CP or you can set the minutes and then confirm by pressing key B m By pressing the CP button you can select the next phase or press the button in order to leave the programming To switch off the automatic timer proceed as follows Press key P Press key N BpIsFLAvV UNIT ON 13 11 Programming automatic switch off time OFF AFTER 5 0 HOURS W Press key P By briefly pressing key or you can set the hours and then confirm by pressing key P 0 5 to 9 0 hours m By pressing the P butto
5. Art Nr 63721 IMPRESSA X90 X95 Instructions for use 5 02 uw IMPRES Jura Impressa X90 X95 a 6 22 Legend FLAY DISPLAY serves as information jisrL amp v DISPLAY please follow the instructions shown moor Hi Jura Elektroapparate AG CH 4626 Niederbuchsiten Note Important Tip Internet http www juraworld com I J Service Instructions for use Drip tray residual water container Drip tray cover Cover for programming keys Coffee key for 2 large cups Coffee key for 1 large cup Coffee key for 2 small cups Coffee key for 1 small cup Key for special coffee ON OFF switch Rinsing key Display dialogue system Water tank with carrying handle Cover for bean container and aroma protection lid Cover for pre ground coffee filler funnel Height adjustable coffee spout Cup warming tray Selector key for steam Selector key for steam portion Selector switch for coffee or hot water Pivoting nozzle for steam Profi Auto Cappuccino Caff Latte Height adjustable tea spout Container for coffee grounds Programming keys A B T Change filter Back setting of criteria changing of memory indications downwards Open program Selector switch for pre ground coffee Key for cleaning program Correction of program close Forward setting of criteria c
6. Water hardness gt Economy mode gt Timer clock gt Automatic switch on time gt Automatic switch off time gt Supplies and cup counter gt Language selection 13 1 Programming powder quantity m Switch the machine on by pressing ON OFF key D W Press key P until you can hear an acoustic signal POWDER QUANTITY SELECT KEY W Now press the key that you want to programme Use the key for 1 cup only The corresponding quantity for 2 cups is adjusted automatically by the machine after programming is finished mg cirer POWDER GT m The powder quantity can be selected by pressing keys or briefly W To store the new powder quantity in memory briefly press key P GISFLA POWDER QUANTITY SELECT KEY W By pressing the CP button you can select the next phase or press the N button in order to leave the programming 13 2 Programming coffee temperature m CIPLA TEMPERATURE COFFEE SELECT KEY W Now press the key that you want to programme W Select the required temperature high or normal by activating key CB or W To store the new coffee temperature in memory briefly press key p IPLAY TEMPERATURE COFFEE SELECT KEY m By pressing the button you can select the next phase or press the N button in order to leave the programming 13 3 Programming water quantity m IPLAY WATER QUANTITY SELECT KEY W Put a cup under the coffee spout 15 and then press the key that you wa
7. for hot milk cappuccino or for less hot milk cappuccino Individual fine adjustment is possible 12 11 6 Cleaning the Profi Auto Cappuccino Caff Latte As soon as you have frothed enough milk it is important to clean the Profi Auto Cappuccino Caff Latte Fill water in a milk container and immerse the intake tube in the water Now draw off steam until the water steam mixture flowing into your cup is completely clean Your Profi Auto Cappuccino Caff Latte is clean again ap Remove Profi Auto Cappuccino Caff Latte 21 If you do not achieve optimum results disassemble the flow controller and the selector lever Fig 10 Thoroughly rinse these parts with water 12 Switching off machine When the machine is switched off the rinsing program is auto matically run again Therefore place an empty container under the coffee spout 15 and press ON OFF key D When the rinsing water has run into the container the machine powers down Dis card the water 13 Programming Before leaving our factory the machine is adjusted to enable you to obtain coffee without any additional programming In order to adapt the result to your personal taste various settings can be pro grammed individually The programming keys are located behind the front cover 3 The following settings can be programmed gt Powder quantity gt Coffee temperature gt Water quantity gt Steam portion gt Tea portion gt Filter
8. container 13 and remove aroma pro tection lid W Clean out any dirt or foreign object from the bean container m Fill the grinder container Fig 1 with coffee beans replace aroma protection lid and close the cover 3 4 Adjusting grinder You can adjust the grinder to the roast of your coffee We recom mend the following for a light roast a finer adjustment for a dark roast a coarser adjustment W Open the cover of the bean container 13 W To adjust grinding turn selector switch Fig 1 to the desired position W You have the following possibilities the smaller the dots the finer the grinding the bigger the dots the coarser the grinding The grinding grade should only be adjusted while the grinder is working 4 Preparing machine 4 1 Fill system with water m Switch your machine on by pressing ON OFF key D The machine adjusts fully automatically to the starting position W DIisELeV PLEASE WAIT m FILL SYSTEM PRESS STEAM W Press key db W OTSFL4 FILL WATER m Remove water tank and rinse well with clear tap water m Fill water tank and replace Make sure that tank engages well m DISPLAY FILL SYSTEM PRESS STEAM W Place a container under the pivoting nozzle 20 and press key db prsrLev PLEASE WAIT m OTSFLAY RINSE UNIT W Place a container under the coffee spout 15 and press rinsing key A W tisa UNIT RINSING m ciskeLev COFFEE READY 4 2 Cup illumination The cu
9. on a surface that is warm or hot hob etc Choose a location that is inaccessible for children or pets m Remove plug from power socket if an absence for a longer period of time holidays etc is planned W Always remove plug from power socket before cleaning m When removing plug from power socket never tug on the cord or on the machine itself W Never repair or open the machine yourself All repairs should be performed by authorised service centres only using original Jura spare parts and accessories W The machine is connected to the mains power socket via an electric cable Ensure that no one trips over this cable and pulls down the machine Keep children and animals at a distance to the machine W Never put the machine or even parts of it in the dishwasher W To prevent overheating place the machine in an airy place W If using acidic decalcifying agents be sure to immediately re move any splashes and drops from delicate surfaces especially natural stone and wooden surfaces or take corresponding pre cautions 3 Check before use 3 1 Checking mains voltage The machine is set for the correct voltage before leaving our factory Ensure that your mains voltage corresponds to the details quoted on the rating plate attached to the bottom of the machine 3 2 Checking fuse The machine is designed for a current of 10 amps Check that an appropriate fuse is fitted 3 3 Adding coffee beans m Lift up cover of the bean
10. only reset to zero if the machine is left switched on TRAY MISSING Tray has not been replaced correctly Grounds have fallen under tray and are preventing it from being correctly inserted Insert tray correctly Remove tray clean inside of machine replace tray EMPTY TRAY 20 The residual water container is full Message still displayed although container emptied Remove container carefully empty rinse out and replace Remove container clean metal contacts please refer to chapter 14 8 DIzFLhAv Cause Action CLEAN UNIT You have drawn off coffee 220 times or run the rinsing program 180 times Message still displayed although machine cleaned Clean as described in chapter 14 6 Run cleaning program again this time do not add cleaning tablet UNIT CALCED The espresso coffee machine sector needs decalcifying Message still displayed although machine decalcified Run decalcifying program as described in chapter 16 Run cleaning program again this time using water only and without decalcifying agent FAULT 2 Temperature too low Switch device off Leave device for approx 2 hours at room temperature Switch device on FAULT 8 Initialisation problem Switch device off disconnect from mains switch on 20 Problems Problem Cause Action Coffee only flows in dribs and drabs while drawing off Powder too fine Adjust grinder to a coarser grinding
11. 2 26 85 HARDNESS German water hardness 16 23 LEVEL 3 French water hardness 28 64 41 14 HARDNESS German water hardness 24 30 LEVEL 4 French water hardness 42 96 53 7 The machine is adjusted to hardness level 3 before it leaves the factory You can alter this setting by following the instructions below m Switch the machine on by pressing ON OFF key D The machine adjusts fully automatically to the starting position Wm cirer PLEASE WAIT m Open cover 3 and press key P until you hear an acoustic sig nal m DIzFL v PRESS KEY POWDER QUANTITY W Press key CP several times until the following message appears m DIzFL vV HARDNESS LEVEL 3 W By pressing key P you can hear an acoustic signal the set hardness level flashes m You can alter the hardness level by pressing key or After setting press key P once again to confirm An acoustic signal can be heard W Press key N to return to stand by status 7 Use of Claris filter cartridges Under proper implementation of Claris filter cartridges decalcifying of the machine becomes unnecessary For further information please read the brochure Claris Tough to calcium deposits gentle to your coffee machine 7 1 Placing filter m Pull up cartridge mounting Pressing lightly place the filter cart ridge in the water tank Fig 2 m Pull down cartridge mounting until it engages audibly m Fill water tank with cold
12. apter 7 1 Placing filter 13 7 Programming water hardness only with setting Filter no m nisFLAv HARDNESS LEVEL 3 E Press key P m By pressing key or briefly you can programme the water hardness level W Then press key P briefly to store the water hardness level in memory m By pressing the button you can select the next phase or press the N button in order to leave the programming m To determine the water hardness level please read chapter 6 Adjusting for water hardness 14 13 8 Programming economy mode W GrSFL4A ECONOMY MODE OFF W Press key P m By briefly pressing key CB or you can programme the mode you would like W Then press key P briefly to store mode in memory m By pressing the button you can select the next phase or press the N button in order to leave the programming You can programme your machine to economy mode In the set ting ECONOMY MODE ON the steam heating system is switched off The heating for the cup warming tray is switched off too If you want to draw off steam you need to press the steam key dL warning lamps flash and your machine heats up After 10 minutes the steam heating system switches off automatically The warning lamps go out By pressing the steam key anew you return to stand by status for drawing off steam ECONOMY MODE OFF means that the stand by status for steam is set to 20 minutes and the heating for the cup warming tray is on
13. der with a vacuum cleaner W Replace bean container and fasten screws 14 6 Clean machine W DIsFL Y CLEAN UNIT After coffee etc has been drawn off 220 times or after 180 rinsing programs have been run the machine must be cleaned You can continue to draw off coffee and hot water steam However we recommend that you clean the machine as described in chapter 15 within the next few days CLEAN NOW An acoustic signal indicates the need of an immediate cleaning 14 7 Unit calcified W DIZFLa V UNIT CALCED The machine signals when decalcifying becomes necessary m Under the correct implementation of Claris filter cartridges decalcifying of the machine becomes unnecessary For further indications read Chapter 7 Use of Claris filter cart ridges 14 8 Cleaning metal contacts m GIrsrir EMPTY TRAY CLEAN CONTACTS W The remnants of the calcified deposits in the area of the metal contacts must be removed Proceed as follows E Rinse fastenings in groove B as well as the metal contacts A with hot water and some washing up liquid Then clean the fastenings in groove B as well with a brush Fig 8 14 9 General cleaning instructions W Never use abrasive articles or corrosive chemicals to clean your machine m Wipe down the casing inside and out using a soft damp cloth W Clean the pivoting nozzle after every use W After warming milk draw off some hot water to clean the pivoting noz
14. en refined and further developed by Jura the Intelligent Pre Brew Aroma System I P B A S ensures full coffee aroma The Auto Cappuccino for example automatically takes charge of frothing the milk perfectly for your cappuccino It sucks milk from a Tetra Pak or a jug heats and froths it up Just choose the pro grammable steam quantity or the continuous steam function Pre paring a cup of tea with your machine is as simple as can be as well The water quantity can be programmed and you can put your teacup under the coffee spout Now the selected water quantity flows into your cup through a separate spout The machine works fully automatically at the press of a key A decoded text display shows messages and simplifies the operation considerably Because of the integrated rinsing cleaning and decalcifying programs care and maintenance is quick and easy 2 Safety instructions 2 1 Warnings m Children are unaware of the dangers that electrical machines re present Therefore children should never be left unsupervised around electrical machines W This machine should only be used by people who have read and understood the operating instructions W Never use a faulty machine or one with a damaged power cable W Never immerse the machine in water 2 2 Safety precautions W Never expose the machine to the effects of rain snow or frost and never operate it with wet hands W Place your machine on a solid level surface Never leave it
15. fresh tap water and replace it m Switch the machine on by pressing key ON OFF W Open front cover 3 and press key P until you hear an acoustic signal pizrPLAv PRESS KEY POWDER QUANTITY W Press key several times until the following message appears FILTER NO m You can alter the setting by pressing key or P YES flashes W To confirm press key P An acoustic signal can be heard RINSE FILTER PRESS STEAM W Place a sufficiently large container approx 1 litre under the pivoting nozzle 20 and press coffee key m orsrLayv PLEASE WAIT FILTER RINSING The drawing off of water will stop automatically W 1 FILTER YES W Press key W GISFLA COFFEE READY a gt The water might be slightly discoloured this is not damag ing to the health 7 2 Replacing of filter After drawing off 50 litres the filter loses its effect m DISPLAY REPLACE FILTER If only a little water is drawn off the filter should be changed every 2 months However no message will appear on the display You will find a special turntable on the cartridge mounting to set the replacement date 10 W Empty water tank and pull up cartridge mounting Pressing lightly place the filter cartridge in the water tank Fig 2 m Pull down cartridge mounting until it engages audibly m Fill water tank with cold fresh tap water and replace it m Switch the machine on by pressing key ON OFF D m Open fr
16. hanging of memory indications upwards Key for decalcifying program Table of contents 1 Description zc Ee te a page 2 Satety InstEUCEIOTS iuo od kia page 2 1 page 2 2 Safety precautions sss page 3 Check Before USE is ete m ne ln page 3 1 Checking mains 0 0906 page 3 2 Checking fUSe cere ett page 3 3 Adding coffee beans eet page 3 4 Adjusting grinder page 4 Preparing 8 page 4 1 Fill system with page 4 2 Cup illumination page 5 Rinsing the 8 page 6 Adjusting for water 6 page 7 Use of Claris filter page page 7 2 Replacing of filter page 8 Drawing off 00 86
17. ity page 13 4 Programming steam portion page 13 5 Programming page 13 6 Programming filter page 13 7 Programming water hardness page 13 8 Programming economy mode page 13 9 Programming timer clock page 13 10 Programming automatic switch ON TME s si d e ba ero page 13 11 Programming automatic switch Off CIM eux page 13 12 CUP COUNTER crore page 13 13 Programming language selection page 13 14 Program key page Care and maintenance page 14 1 Bill waten page 14 2 Empty grounds page 14 3 Empty drip tray isnin ccein eaten page 14 44 Fillbeansz e t ete EE obe page 14 5 Removing foreign objects page 14 6 Clean machine sese page 14 1 Unit calcified te page 14 8 Cleaning metal page 14 9 General cleaning instructions page 14 10 Regular servicing
18. milk container and immerse the intake tube in the milk W Put a cup under the pivoting nozzle 20 and press key amp W DizEL v STEAM PORTION W The drawing off of steam will stop automatically COFFEE READY If the Profi Auto Cappuccino Caff Latte has not been used for a longer period of time press selector key first until the milk is taken in then selector key amp In this way you will obtain a regular steam portion 11 11 2 Constant frothing up of milk W Pour milk into a milk container and immerse the intake tube in the milk m Put a cup under the pivoting nozzle 20 and press key Your milk froths up DisrLAv STEAM INTAKE m When the required amount of froth has been attained push selec tor key 4b anew COFFEE READY 11 3 Drawing off hot milk using the Profi Auto Cappuccino Caff Latte The Profi Auto Cappuccino Caff Latte can be used to draw off hot milk Adjust the selector lever 1 Fig 10 to position 3 to draw off hot milk Install the Profi Auto Cappuccino Caff Latte This is in cluded in your Welcome Pack 11 4 Drawing off cappuccino using the Profi Auto Cappuccino Caff Latte The Profi Auto Cappuccino Caff Latte can be used to draw off capuccino Adjust the selector lever 1 Fig 10 to position 2 to draw off capuccino 11 5 Controlling the temperature using the Profi Auto Cappuccino Caff Latte Adjust the selector lever 1 to
19. n you can select the next phase or press the button in order to leave the programming 13 12 Cup counter W irav 200 SUPPLIED TOTAL SUPPLIED W To obtain the information press the required key The display will show you the number of times the function has been chosen m By pressing the button you can select the next phase or press the N button in order to leave the programming It is not possible to call up hot water and steam supplies 13 13 Programming language selection W Press key P m By briefly pressing key or call up the language desired and then confirm by pressing key P m By pressing the button you can select the next phase or press the N button in order to leave the programming 13 14 Program key By using key you can set back the following settings powder quantity coffee temperature water quantity steam portion tea portion to their original standard settings W pIzFLA v COFFEE READY W Press key N until you can hear an acoustic signal ES If a mistake occurs while programming one of the above settings just press key 8 and the chosen setting moves back to its original standard setting 15 E 14 Care and maintenance 14 1 Fill water m OISFLAY FILL WATER W If this message shows on the display no more coffee can be drawn off Top up water The water tank should be rinsed and filled with fresh water daily Only use fresh cold water Never top up
20. nt to programme W tPA The selected value is confirmed W Now your machine prepares a coffee m ENOUGH COFFEE PRESS KEY P mg nizrFL v OK P I e m When the required water quantity is reached press key P You can call up the next setting by pressing key CP W There is an additional possibility to alter the water quantity anew Press key CP or 5 for this purpose W If you wish to draw another coffee to control the water quantity press key again otherwise press key P briefly to store water quantity in memory m By pressing the button you can select the next phase or press the N button in order to leave the programming 13 4 Programming steam portion W DisPLev STEAM PORTION W Press key P W pizELev PORTION 20 SEC m By pressing key CP or you can programme time in seconds drawing off time of 3 250 sec W Press key P W DizsFL v STEAM PORTION 13 By pressing the P button you can select the next phase or press the N button in order to leave the programming 13 5 Programming tea portion W Place a cup under the height adjustable tea spout 22 W Press key P m DISPLAY OPEN TAP m DISPLAY ENOUGH TEA CLOSE TAP m nisrFLav TEA PORTION W The required portion of tea water is programmed now m By pressing the CP button you can select the next phase or press the N button in order to leave the programming 13 6 Programming Filter Please read ch
21. ont cover 3 and press key 9 until you hear an acoustic signal m DISPLAY RINSE FILTER PRESS STEAM W Place a sufficiently large container approx 1 litre under the pivoting nozzle 20 and press coffee key m PLEASE WAIT FILTER RINSING m OTESFLAY COFFEE READY EN The water might be slightly discoloured this is not damag ing to the health 8 Drawing off coffee m Switch the machine on by pressing key ON OFF D PLEASE WAIT crseLey RINSE UNIT Put an empty cup under the coffee spout 15 and press rinsing key g UNIT RINSING m sisenev COFFEE READY W Put 1 respectively 2 cups under the coffee spout and press the required key The pre brew system LP B A S 9 moistens the coffee powder briefly interrupts the flow and then starts the real brewing process EY You can interrupt the flow of coffee at any time by simply pressing any of the coffee keys To obtain a perfect layer of froth adjust the coffee spout Fig 3 to the size of your cups 8 1 Drawing off powder coffee B Open cover 3 W Press selector key for pre ground powder coffee S m oISsFLA FILL POWDER W Now put 1 or 2 level measuring spoons of pre ground coffee into the pre ground powder funnel 14 W Put 1 respectively 2 cups under the coffee spout 15 and press the required key Never use soluble instant coffee or quick coffee Only use coffee powder from freshly ground beans or pre g
22. p illumination puts your coffee in a good light making it a treat for the eyes When you switch on the machine or press any key the cup illumi nation is activated for 3 minutes To switch on the cup illuminati on with the machine switched off press any key 5 Rinsing the machine DISFLAv RINSE UNIT W Place an empty cup under the coffee spout 15 W Press rinsing key ES If the machine has been switched off and has already cooled down it will be necessary to carry out this rinsing function when the machine is switched on again After switching off the machine the rinsing sets off automa tically 6 Adjusting for water hardness The water is heated inside the machine With use this leads to calcium deposits furring forming on the machine This will be automatically indicated on the display For this reason it is necessary to adjust the machine to the hardness of your local water before you use it for the first time Use the enclosed test sticks for this purpose ES 1 water hardness on the German scale represents 1 79 on the French scale The machine has got 5 hardness settings to choose from While adjusting the chosen grade is shown on the display The symbols on the display mean HARDNESS LEVEL water hardness function is switched off HARDNESS German water hardness 1 7 LEVEL 1 French water hardness 1 79 12 53 HARDNESS German water hardness 8 15 LEVEL 2 French water hardness 14 3
23. rip tray bisFL v ADD TABLET Fig 9 PRESS CLEANING npisFLAv UNIT CLEANING PLEASE WAIT OTSFLAY EMPTY TRAY PLAY PLEASE WAIT RINSE UNIT COFFEE READY The powder funnel for pre ground coffee should be cleaned after each cleaning process Remove it from the machine rinse it with hot tap water and replace it after drying 16 Decalcifying Your machine has an integrated decalcifying program It lasts approx 50 minutes Please use Jura decalcifying tablets only These are available from your Jura dealer Run the decalcifying program only after the machine has been switched off for at least 5 hours and has cooled down completely The running decalcifying program must not be interrupted H If using acidic decalcifying agents be sure to immediately re move any splashes and drops from delicate surfaces especi ally natural stone and wooden surfaces or take correspond ing precautions In any case please wait until the filled decalcifying agent is used up and the tank is empty Never top up the decalcifying agent 18 W Remove and empty water tank W Replace empty water tank m Switch off your machine by pressing ON OFF 1 key and let it cool down for approx 5 hours W Open cover 3 E Press key Hj until you can hear an acoustic signal EMPTY TRAY AGENT IN TANK Pour 0 6 litres of water into a container and completely dis solve the contents of a blister pack 2 tablets Then fill the mixture in
24. round vacuum packed coffee Never fill the funnel with more than 2 portions coffee powder at a time The powder fun nel is not intended as a storage container If selector key is pressed by mistake this can be cor rected by pressing one of the coffee keys The rinsing pro gram is then activated 9 Drawing off hot water W Put a cup under the height adjustable coffee spout 22 and turn selector switch for hot water 19 to the symbol 11 The machine will now deliver hot water TEA PORTION The drawing off of hot water will stop automatically pizPL CLOSE TAP Turn selector switch for hot water back to the symbol UP stop this process turn selector switch for hot water 19 back to the symbol UP 10 Drawing off steam Steam can be used for heating liquids Make sure that the steam frothing nozzle Fig 4 is pushed upwards when liquids are heated Push down the frothing aid to froth liquids In the case of machine types the steam frothing aid is installed as a standard Fig 4 You can install the Profi Auto Cappuccino Caff Latte This is included in the Welcome Pack also refer to Chapters 11 3 11 4 11 5 11 Frothing up milk with the Profi Auto Cappuccino Caff Latte Your machine is ready for frothing up milk as soon as both selec tor key warning lamps 4 glow constantly If the lamps do not glow then press either steam key 11 1 Frothing up a portion of milk W Pour milk into a
25. s on the part of Jura Elektroapparate AG result solely from the relevant sales agreement which also contains full details of the only warranty terms valid in respect of this machine The con tractual terms of this warranty are neither extended nor limited in any form by the information in these operating instructions These operating instructions contain information that is protected by copyright The photocopying or translation into any other language of these instructions without prior written authorisation from Jura Elektroapparate AG is strictly prohibited 22 22 Technical specifications Impressa X90 X95 Voltage Output Fuse Safety check Energy consumption standby Energy consumption ready to make coffee Pump pressure Capacity bean container Cable length Water tank Capacity grounds container Weight Dimensions B x H x D 230 V AC 1350 W 10 A CE approx 4 4 Wh approx 31 Wh Economy Mode on approx 41 Wh Economy Mode off max 15 bar 280 gr approx 1 1 m 5 7 litres max 40 port 15 kg 41 x 47 x 39 cm
26. size of your cups Grinding Please refer to chapter 3 4 Adjusting grinder Pre warm cups You should warm cups in advance with hot water or steam The smaller the quantity of coffee the more important warming the cups is Sugar and cream Warmth is lost by stirring the contents of the cup Adding milk or cream from the refrigerator considerably lowers the temperature of the coffee 19 19 Messages DISPLAY Cause Action FILL WATER Water tank is empty Top up with water Water level indicator in tank is jammed Empty tank rinse out fill up and replace Tank is calcified water level indicator is stuck Remove tank decalcify rinse well fill up with water and replace FILL BEANS Bean container is empty Top up with beans Message still displayed although beans filled A foreign object is stuck in the grinder Draw off cup of coffee FILL BEANS message only disappears after coffee is drawn off Remove foreign object as described in chapter 14 5 Removing foreign objects EMPTY GROUNDS Coffee grounds container is full Message still displayed although grounds container emptied The message appears after only a few cups have been drawn off Remove drip tray empty grounds container replace tray The tray was out of the machine for less than 8 sec for emptying Take tray out again for approx 10 sec and replace Leave the machine switched on while the grounds container is being emptied The counter is
27. to the water tank W DISFL AGENT IN TANK OPEN TAP PRESS CALC Place a sufficiently large container under the pivoting nozzle 20 Remove the Profi Auto Cappuccino Caffe Latte m Turn selector switch for coffee 19 to the symbol and press key H W tisa UNIT DECALCIFYING PLEASE WAIT W When an acoustic signal is heard place a container under the height adjustable tea spout 22 DISPLAY PRESS CALC DISPLAY UNIT DECALCIFYING PLEASE WAIT pIsEPL amp v CLOSE TAP DISPLAY UNIT DECALCIFYING PLEASE WAIT W Inside the machine the decalcifying agent is conducted to the drip tray m DISPLAY EMPTY TRAY m prsrLev FILL WATER W Place a container under the pivoting nozzle 20 DISFLAY OPEN TAP m nisPLav PRESS CALC pIZFL v UNIT DECALCIFIYING PLEASE WAIT Place a container under the height adjustable tea spout 22 pisFL v PRESS CALC DISPLAY UNIT DECALCIFIYING PLEASE WAIT TIFA CLOSE TAP 2 UNIT DECALCIFIYING PLEASE WAIT Inside the machine the water is conducted to the drip tray trpe CLEAN CONTACTS EMPTY TRAY please refer to chapter 14 8 nizFL v PLEASE WAIT pIZFL RINSE UNIT ni ZFLAv UNIT RINSING COFFEE READY 17 Disposal For correct disposal you should return your coffee machine to your dealer Jura service centre or Jura Elektroapparate AG 18 Tips for a perfect coffee Height adjustable coffee spout You can adjust the height of the coffee spout to the
28. with milk mineral water or any other liquids You can top up water without removing tank 14 2 Empty grounds container Coffee grounds are collected in the grounds container 23 Wm OISFLAY EMPTY GROUNDS W If this message shows on the display no more coffee can be drawn off It is necessary to empty the grounds container m Remove drip tray carefully as there is water in it Do not disconnect the machine from power socket while you empty grounds 14 3 Empty drip tray m EMPTY TRAY W If this message shows on the display no more coffee can be drawn off It is necessary to empty the drip tray m Remove drip tray carefully as there is water in it 16 14 4 Fill beans m poisrtev FILL BEANS W Fill beans as described in chapter 3 3 ay The message FILL BEANS will only disappear after drawing off a coffee We recommend cleaning the bean container from time to time with a dry cloth before you refill beans Switch off the machine for this purpose 14 5 Removing foreign objects m Switch off your machine by pressing ON OFF key D m Remove plug from power socket W Open bean container 13 and remove the beans The remaining beans can be removed with a vacuum cleaner W Loosen both screws in the bean container and then remove container Fig 5 6 m Remove any remaining beans with a vacuum cleaner W Put the spanner on Fig 7 W Now turn spanner anticlockwise until the foreign object loosens m Remove remaining pow
29. zle inside W You can take off the Profi Auto Cappuccino Caff Latte for a thorough cleaning W The water tank should be rinsed and filled with clean water daily If you notice any furring in the water tank this can be de calcified separately with a customary decalcifying agent Remove the tank from the machine for this purpose Hi If a Claris filter cartridge is used remove it beforehand 14 10 Regular servicing Regular Jura services ensure your machine s reliability and longer life Keep the original packaging to protect the machine while being transported 14 11 Empty system This procedure is necessary to prevent your machine from frost damage while being transported W Put a container under the pivoting nozzle 20 E Press selector key and remove water tank W DIZFL vV STEAM INTAKE m DIzFL v PRESS STEAM FILL SYSTEM m Switch off machine by pressing ON OFF key D 15 Cleaning The machine has an integrated cleaning program The procedure lasts about 15 minutes Please use Jura cleaning tablets only These are available from your Jura dealer It is essential not to interrupt the process once it has been started m Switch on your machine by pressing ON OFF D key W Press key until you can hear an acoustic signal ms EMPTY TRAY FILL WATER might show as well 17 Put a sufficiently large container under the coffee spout 15 in order to prevent cleaning liquid from running into the d
Download Pdf Manuals
Related Search