Jensen JCR-290 User's Manual
Contents
1. Now repeat step 4 above If the unit fails to understand the alarm source given a second time it will reply I m sorry did not understand you please start over or set the alarm sound manually If this occurs repeat steps 1 4 above again making sure you speak clearly in a normal voice When the alarm source is successfully understood the unit will reply To choose an alarm sound say Ocean Rain Brook Radio or Beep Say Ocean Rain Brook Radio or Beep You can also say the command Cancel during this step if you wish to cancel setting the alarm sound and the unit will reply OK to confirm When the alarm sound is successfully understood the unit will reply Alarm One sound is set to and repeat the alarm sound you have chosen The alarm one sound selected will light in the display 25 If the unit fails to understand the alarm sound given for the first and second times it will reply Please Repeat Now repeat step 8 above If the unit fails to understand the alarm sound given a third time it will exit with further prompt message To set Alarm Two Sound repeat steps 1 4 and 8 above and say Alarm Two when prompted step 4 The alarm two sound selected will light in the display 26 when completed E 13 NOTE When the preset alarm time is reached the chosen alarm sound will start sounding at a fairly low volume level and gradually increase to a very loud vol2. 4 BUTTONS adjust to the desired minute for AL1 5 Press SET BUTTON 5 The SOUND EFFECT INDICATORS of AL1 will flash 25 6 Use the gt UP 6 or lt DOWN 4 BUTTONS to choose a Wakeup Alarm Sound Ocean Rain Brook Radio or Beep Alarm E 8 11 Press SET BUTTON 5 to proceed to 12 settings following steps 1 to 6 above 12 indicators 26 will respond to the features chosen Press SET BUTTON 5 to proceed to TIME settings following steps 1 to 4 above Press SET BUTTON 5 to proceed to Sleep Sound settings Use the gt UP 6 or lt DOWN 4 BUTTONS to choose a Sleep Sound Ocean Rain Brook or Radio Except in alarm snooze or sleep modes you may cycle through and review the set alarm time alarm sound and sleep sound settings by pressing the SET BUTTON 5 repeatedly USING SMART TALK For correct operation of SMART TALK please be sure to operate the unit in the following conditions The ambient condition is fairly quiet The radio or alarm sound is not playing The TRIGGER SWITCH 3 is set to ON The Voice indicator 29 will turn on You are within 6 24 inches from the built in MICROPHONE located on the top of the unit right behind the SET BUTTON 5 Remarks the farther away from the mic the louder you have to say the voice commands E 9 SMART TALK COMMANDS COMMAND FUNCTION DESCRIPTION AND FACTORY PRESET PHRASE Smart Talk Trigger word to act
3. OFF position to temporarily disables the Smart Talk feature Say Cancel if you hear the unit saying Yes on its own Repeat the command clearly at louder voice while facing the unit Retune the AM or FM broadcast station FM Fully extend FM wire antenna AM Reposition the unit until the best reception is obtained Press On Off Button until radio is on Increase Volume Unplug the line in cord Adjust Volume Control to a lower comfortable level LCD brightness is too dim Display brightness set to dim mode E 22 Set display brightness to HI manually or by Smart Talk command 90 DAY LIMITED WARRANTY AND SERVICE VALID IN THE U S A ONLY SPECTRA MERCHANDISING INTERNATIONAL INC warrants this unit to be free from defective materials or factory workmanship for a period of 90 days from the date of original customer purchase and provided the product is utilized within the U S A This warranty is not assignable or transferable Our obligation under this warranty is the repair or replacement of the defective unit or any part thereof except batteries when it is returned to the SPECTRA Service Department accompanied by proof of the date of original consumer purchase such as a duplicated copy of a sales receipt You must pay all shipping charges required to ship the product to SPECTRA for warranty service If the product is repaired or replaced under warranty the return c
4. USING THE LINE IN TO LISTEN TO EXTERNAL AUDIO PLAYER You may playback your favorite music from your iPod or a portable digital audio player using the Line in function 1 Connect the headphone jack of your external device to the LINE IN JACK 18 at the rear cabinet of this unit using a stereo cord with a 3 5mm phone plug on either ends Note the stereo cord is not included E 19 2 Press the ON OFF BUTTON 12 to turn on the radio It will automatically switch to Line In mode when a suitable stereo cord is correctly connected 3 Start playing your external audio device 4 Slowly increase the volume control of the unit until the desired level is obtained To avoid output sound distortion due to overloading you may need to lower the volume output of your audio device Note the stereo music from your audio device will be converted to a monaural audio output 5 Turn off your external audio device first when you finish listening 6 Then unplug the stereo cord from the LINE IN JACK 18 and normal radio reception will resume DIMMER CONTROL MANUAL SETTING The display HI LO DIMMER BUTTON 19 is located the back of the unit Pressing it will toggle between bright and dim backlight options for the display USING SMART TALK 1 Start by saying the trigger word Smart Talk or press the Snooze Bar 11 2 The unit will reply Yes and will wait for your next command 3 Say Display and the unit
5. Yes and will wait for your next command 3 Say Time and the unit will reply The time is followed by the present time ALARM TIME AND ALARM SOUND SETTING CHECKING TO SET THE ALARM TIME AL1 AL2 1 Start by saying the trigger word Smart Talk or press the SNOOZE BAR 11 2 The unit will reply Yes and will wait for your next command E 11 10 11 12 Say Set Alarm and the unit will reply Say Alarm One or Alarm Two set Alarm One say Alarm One You can also say the command Cancel during this step if you wish to cancel setting the alarm and the unit will reply OK to confirm If the unit fails to understand the alarm source given it will reply Please Repeat Now repeat step 4 above If the unit fails to understand the alarm source given a second time it will reply I m sorry did not understand you please start over or set the alarm time manually If this occurs repeat steps 1 4 above again making sure you speak clearly a normal voice When the alarm source is successfully understood the unit will reply Please say the time you would like the alarm to sound including AM or PM Say the time you wish Alarm One to sound Example to set Alarm One to 10 19AM say Ten Nineteen AM When the alarm one time is successfully understood the unit will reply Alarm One is now set to and repeat the time you g
6. will reply Say Display Low or Display High 4 Say High or Low to set the display brightness accordingly You can also say the command Cancel and the display will stay at it s current setting 5 If you do not say the command word correctly the unit will prompt you to repeat or start all over again RESETTING THE UNIT After you have installed backup batteries and connected the unit to AC power source for the first time we recommend you to press the RESET Button 15 at the bottom of the cabinet to correctly initialize it E 20 In case of an erroneous display or prolonged abnormal behavior during normal use you can also safely restore it to its factory preset conditions by pressing the RESET Button 15 Please note that all personal settings including current time alarm time and sleep session will be cleared So be sure to set up the clock again according to previous sections above SPECIFICATIONS Frequency Range AM 530 1710 kHz FM 88 108 MHz AC Power Source 120V 60Hz 5W Backup Battery 2 x 3V type CR2032 Lithium batteries Not included Clock Accuracy to 60 seconds per month CARE AND MAINTENANCE 1 Children should be supervised when using this appliance 2 Never wrap the ac power cord around any animal or person Special care should be taken with long wire 3 Clean your unit with a damp never wet cloth Solvent or detergent should never be used 4 Avoid leaving
7. your unit in direct sunlight or in hot humid or dusty places 5 Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors 6 Always keep the microphone area clean and free from foreign matters for best voice recognition accuracy TROUBLESHOOTING GUIDE Symptom Possible Cause Solution The clock does not recognize your voice commands correctly Surrounding is too noisy The radio is playing Change to a quieter place or speak closer to the unit s mic at louder voice Voice recognition is not designed to work in radio mode you need to use manual settings instead Smart Talk accidentally triggers without saying the trigger word The unit is located in a noisy room or near a radio or TV Clock does not always recognize Alarm Off command during alarm and snooze Noise or distorted Station not tuned properly for on AM or FM broadcast AM or FM FM FM wire antenna is not extended AM The unit is not placed in best reception point Unit not in RADIO function mode Volume set at minimum An external non playing digital The surrounding is relatively noisy Your voice level is too low AM or FM no sound audio player is connected to the line in jack Volume control of this unit is set to maximum Sound appears distorted at high volume setting Set the Trigger Switch 3 to the
8. E The unit will operate without batteries installed but your time and alarm settings will be lost and have to be reset in the event of a power interruption or failure IMPORTANT Be sure that the batteries are installed correctly Wrong polarity may damage the unit and void the warranty For best performance and longer operating time we recommend the use of good quality batteries A CAUTIONS le 2 3 Do not mix old and new batteries Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries If the unit is not to be used for an extended period of time remove the batteries Old or leaking batteries can cause damage to the unit and may void the warranty Do not dispose of batteries in fire batteries may explode or leak Replace all the batteries no matter exhausted or not every 2 years at the same time to avoid possible battery leakage CONNECTING THE UNIT TO AC POWER SOURCE Please be sure the outlet you plug this unit into is working and provides uninterrupted power 1 2 Insert the AC plug of the AC power cord into 120V 60Hz outlet Press the RESET BUTTON on the bottom of the unit with a pointed object e g a straighten paper clip to initialize After a brief self test the unit enters the clock mode To listen to the radio press On Off Button E 7 WHAT IS SMART Smart Talk is an innovative clock operating system using the latest voice recognition t
9. JENSEN audio MODEL JCR 290 AM FM TALKING DUAL ALARM CLOCK RADIO WITH SMART TALK USER MANUAL PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE THIS PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE TO PREVENT FIRE ORSHOCKHAZARD DONOTEXPOSETHISAPPLIANCETORAINOR MOISTURE WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture CAUTION Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICING TO QUALIFIED SERVICE PERSONNEL voltage within the product s enclosure that may be of sufficient The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance The caution marking is located at the back c
10. abinet of the apparatus IMPORTANT SAFETY INSTRUCTIONS Read these Instructions Keep these Instructions Heed all Warnings Follow all Instructions Do not use this apparatus near water Clean only with a dry cloth Vote ls E 1 Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer 12 Use only with a cart stand tripod bracket or table specified by the manufacturer 17 18 19 or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for rontaste cart wanuna long periods of time Refer all servici
11. alarm will sound again the next day at the same preset time If radio is chosen as the alarm sound it will play without interruption and therefore you will not be able to use Smart Talk Alarm Off command to turn it off The radio alarm will have to be turned off by pressing either AL1 ON OFF 2 AL2 ON OFF 8 or ON FF 12 BUTTON Follow the steps in the above Smart Talk section TO CHECK THE ALARM TIME AL1 AL2 to turn the specific alarm off with voice commands if it is initially on The corresponding alarm indicator on the display 25 and or 26 will turn off to confirm SETTING UP THE SLEEP SOUND AND TIME You can choose either a nature sound Ocean Rain or Brook or the radio as a sleep sound The sleep time can be adjusted from 15 30 45 or 60 minutes and OFF MANUAL SETTING SETTING THE SLEEP SOUND 1 2 3 The Sleep Sound can be set by repeatedly pressing the SET BUTTON until you get to the to Sleep Sound settings Use the gt UP 6 or lt DOWN 4 BUTTONS to choose a Sleep Sound Ocean Rain Brook or Radio The display will show the chosen Sleep sound 27 E 17 ACTIVATE SLEEP MODE AND SETTING SLEEP TIME 1 2 Press the SLEEP BUTTON 10 to start the sleep mode The sleep time is default to 60 minutes on first use and 60 will on the display 24 Press the SLEEP BUTTON 10 repeatedly to cycle through shorter sleep time options of 45 30 15 minutes
12. ave Example if you said to set the alarm time to 10 19AM the reply will be Alarm One is now set to ten nineteen The Alarm One indicator on the display 25 will now light If the unit fails to understand the alarm time given it will reply I m sorry didn t get that Please tell me the time you would like the alarm to set for example eight thirty AM Now repeat step 8 above If the unit fails to understand the alarm time given a second time it will reply I m sorry did not understand you please start over or set the alarm time manually If this occurs repeat steps 1 4 and 8 above again making sure you speak clearly in a normal voice and avoid pauses between words To set Alarm Two repeat steps 1 4 above and say Alarm Two when prompted step 4 The Alarm Two indicator on the display 26 will light once complete E 12 TO SET THE ALARM WAKE SOUNDS AL1 AL2 1 2 3 10 11 12 Start by saying the trigger word Smart Talk or press the SNOOZE BAR 11 The unit will reply Yes and will wait for your next command Say Alarm Sound and the unit will reply To set alarm sound please say Alarm One or Alarm Two To set Alarm One say Alarm One You can also say the command Cancel during this step if you wish to cancel setting the alarm sound If the unit fails to understand the alarm source given it will reply Please Repeat
13. blish your eligibility for warranty service and repair of the unit without cost Also include a note with a description explaining how the unit is defective A customer service representative may need to contact you regarding the status of your repair so include your name address phone number and e mail address to speed the process E 23 IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD please include a check for 15 00 to cover the cost of repair handling and return postage All out of warranty returns must be sent prepaid It is recommended that you contact SPECTRA first at 1 800 777 5331 or by e mail at info spectraintl com for updated information on the unit requiring service In some cases the model you have may be discontinued and SPECTRA reserves the right to offer alternative options for repair or replacement SPECTRA MERCHANDISING INTERNATIONAL INC 4230 North Normandy Avenue Chicago IL60634 USA 1 800 777 5331 To register your product visit the link below on the website to enter your information http www spectraintl com wform htm Printed in China E 24 916S JO02
14. echnology It s the HANDS FREE way to set your alarm clock No more fumbling with instructions or pressing multiple buttons to set the time and alarm Once the system is activated by saying the trigger word Smart Talk you now simply say one of the preset voice commands and follow the voice prompts to set up the clock using your voice Setting the Time Alarm Sleep Time Sleep Sound and Alarm Sounds are just a few of the features you can control with voice commands As you become more familiar with this technical marvel you will understand that it has been specifically programmed for voice command of multiple functions Depending on the surrounding ambience potential noise influence and how you speak its language there may be instances of misunderstood commands If this happens just repeat them after checking the way to say your commands so that SmartTalk will obey and also talk to you properly Finally this product can have all functions operated manually the same as all other clock radios SETTING UP DAILY ALARMS AND CLOCK USING MANUAL SETTINGS In radio off mode press SET BUTTON 5 to enter AL1 AL2 Time setup mode 1 The HOUR DIGITS and AL1 indicator in the LCD panel will flash 2 Using the gt UP 6 or lt DOWN 4 BUTTONS adjust to the desired hour for AL1 Press SET BUTTON 5 The MINUTE DIGITS AL1 indicator in the LCD panel will flash 25 4 Using the gt UP 6 or lt DOWN
15. ergy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment DEAR JENSEN CUSTOMER Selecting fine audio equipment such as the unit you ve just purchased is only the start of your musical enjoyment Now it s time to consider how you can maximize the fun and excitement your equipment offers This manufacturer and the Electronic Industries Association s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level One that lets the sound come through loud and clear without annoying blaring or distortion and most importantly without affecting your sensitive
16. harges will be at SPECTRA s expense There are no other express warranties other than those stated herein This warranty is valid only in accordance with the conditions set forth below 1 The warranty applies to the SPECTRA product only while a It remains in the possession of the original purchaser and proof of purchase is demonstrated b It has not been subjected to accident misuse abuse improper service usage outside the descriptions and warnings covered within the owner s manual or non SPECTRA approved modifications c Claims are made within the warranty period 2 This warranty does not cover damage or equipment failure caused by electrical wiring not in compliance with electrical codes or SPECTRA owner s manual specifications or failure to provide reasonable care and necessary maintenance as outlined in the owner s manual 3 Warranty of all SPECTRA products applies to residential use only and is void when products are used in a nonresidential environment or installed outside the United States This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO OBTAIN SERVICE please remove all batteries if any and pack the unit carefully and send it prepaid by insured parcel post or UPS to SPECTRA at the address shown below IF THE UNIT IS RETURNED WITHIN THE WARRANTY PERIOD shown above please include a proof of purchase dated cash register receipt so that we may esta
17. hearing E 3 Sound can be deceiving Over time your hearing comfort level adapts to higher volumes of sound So what sounds normal can actually be loud and harmful to your hearing Guard against this by setting your equipment at a safe level BEFORE your hearing adapts To establish a safe level e Start your volume control at a low setting e Slowly increase the sound until you can hear it comfortably and clearly and without distortion Once you have established a comfortable sound level e Set the dial and leave it there Taking a minute to do this now will help to prevent hearing damage or loss in the future After all we want you listening for a lifetime We Want You Listening For a Lifetime Used wisely your new sound equipment will provide a lifetime of fun and enjoyment Since hearing damage from loud noise is often undetectable until it is too late this manufacturer and the Electronic Industries Association s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise Customer s Record The serial number of this product is found on its bottom You should note the serial number of this unit in the space provided as a permanent record of your purchase to aid in identification in the event of theft of loss Model Number JCR 290 Serial Number E 4 ele ane me 1 2345678 9 14 15 16 20 21 Controls and Funct
18. ions of Unit 1 Volume Control 12 On Off Button 2 ALARM 1 AL1 On Off Button 13 LCD Panel 3 Trigger On Off Switch 14 Rating Label 4 lt Down Button 15 Reset Button 5 Set Button 16 Battery Compartment Cover 6 gt Up Button 17 Speaker 7 AM FM Band Selector 18 Line In Jack 8 ALARM 2 AL2 On Off Button 19 Display Hi Lo Dimmer Button 9 Tuning Control 20 FM Wire Antenna 10 Sleep Button 21 AC Power Cord 11 Snooze Bar also works as Trigger Button for Smart Talk E 5 22 PM Indicator 23 Hour Digits 24 Minute Digits 25 AL1 and Sound Effect Indicators 27 SLEEP and Sound Effect Indicators 29 Smart Talk Indicator Avoid installing the unit in locations described below e Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters Humid moist or dusty places Places subject to constant vibration Noisy places POWER SOURCES This unit operates on 120V 60Hz and requires 2 x CR2032 Lithium batteries not included for system and time backup during power outage Do not attempt to operate the radio on any other power source You could cause damage to the unit and void your warranty INSTALLING BACKUP BATTERIES 1 2 3 Remove the BATTERY COMPARTMENT COVER Install 2 x 3V type CR2032 Lithium batteries not included according to the polarity indications on the BATTERY COMPARTMENT COVER Close the BATTERY COMPARTMENT COVER NOT
19. ivate the voice recognition system Time To check the current time Factory preset time is 12 00AM Set Time To set the current time in AM or PM To check the alarm time and status of AL1 amp AL2 If the alarm is currently off you have the option to turn it on or vice versa Factory preset alarm time is 7 00AM for AL1 and 8 00AM for AL2 Set Alarm To set the alarm time of AL1 amp AL2 in AM or PM Alarm Sound To set the alarm sound for AL1 amp AL2 You can select from among 3 nature sounds Ocean Rain or Brook radio or the beep alarm Factory preset alarm sound is beep alarm for both AL1 amp AL2 m O sounding or clock is in snooze mode To activate the 9 minute Snooze while an alarm is sounding You must say the command word Snooze during the brief pause during the alarm except radio mode in which you need to tap the SNOOZE BAR for it to work correctly Factory preset sleep time is 60 minutes Play Sleep Sound To choose a sleep sound from among 3 nature sounds Ocean Rain or Brook or radio If the sleep time is default to 60 minutes You can adjust sleep sound output between levels 1 4 by pressing the gt UP 6 or lt DOWN 4 BUTTONS Factory preset sleep sound is Ocean and its output level is 2 Display To set the LCD backlight brightness to HI or LO Factory preset LCD brightness is High Cancel To terminate the Smart Talk function immediately after it is acti
20. l go off The alarm will now be off and ready to sound the next day at the preset time TURNING OFF THE ALARM You can turn the alarm off for the day only so that it will sound again on the following day or you can turn the alarm completely off by disabling it MANUAL OPERATION 1 When an alarm is sounding press the ON OFF button 12 to turn the alarm off only for the day The alarm will sound again the next day at the same preset time The alarm indicators on the display 25 amp 26 will remain on If you do not wish the alarm to sound again you can disable it by pressing either the AL1 ON OFF BUTTON 2 or AL2 ON OFF BUTTON 8 The corresponding alarm indicators on the display 25 amp 26 will go off To enable the alarms again press either the AL1 ON OFF BUTTON 2 or AL2 ON OFF BUTTON 8 The corresponding alarm indicators on the display 25 amp 26 will turn on E 16 USING SMART TALK 1 When the designated alarm time is reached there will be a periodic pause in the alarm sound if you chose a nature sound Ocean Rain or Brook or the Beep for your wake alarm This is normal and during the pause is where the unit is listening for the Alarm Off command Say Alarm Off during one of the pauses the alarm sound to turn the Alarm off for the day If the Alarm command is correctly recognized the unit will reply Yes and the alarm sound will stop The
21. ng to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled qe or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has 810 00000S 190 been dropped The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on apparatus Main plug is used as disconnect device and it should remain readily operable during intended use In order to disconnect the apparatus from the mains completely the mains plug should be disconnected form the mains socket outlet completely Battery shall not be exposed to excessive heat such as sunshine fire or the like The marking information is located at the bottom of apparatus CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type AN CAUTION OD TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF AC AC Outlet PLUG TO WIDE SLOT FULLY INSERT 2 SAVE THESE INSTRUCTIONS This equipment has been tested and found to comply with the limits for a radio receiver pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency en
22. or OFF USING SMART TALK SETTING THE SLEEP SOUND 1 2 3 Start by saying the trigger word Smart Talk or press the Snooze Bar 11 The unit will reply Yes and will wait for your next command Say Play Sleep Sound and the unit will reply To Choose a Sleep Sound Say Ocean Rain Brook or Radio Say Ocean Rain Brook or Radio You can also say the command Cancel during this step if you wish to cancel setting the sleep sound and the unit will reply OK to confirm When the sleep sound is successfully understood the sleep sound chosen will show on the display 27 and be played for the selected sleep time If the unit fails to understand the sleep sound given it will reply Please Repeat Now repeat step 4 above ACTIVATE SLEEP MODE AND SETTING SLEEP TIME 1 2 3 Start by saying the trigger word Smart Talk or press the Snooze Bar 11 The unit will reply Yes and will wait for your next command Say Sleep Time and the unit will reply Please choose a Sleep Time say Fifteen Thirty Forty Five or 60 Minutes Say Fifteen Thirty Forty Five or 60 Minutes You can also say the command Cancel during this step if you wish to cancel setting the sleep time and and the unit will reply OK to confirm When the sleep time is successfully understood the unit will say Your Sleep Sound will turn off in Minu
23. sound and also ask if you want to turn the alarm off if on Alarm Two settings will be announced in the same way once the Alarm One setting checks are completed a Example You say Alarm b The unit will reply Alarm One is set to and announce the time alarm one is set to c If Alarm one is on the unit will continue The Alarm is On and play a brief sample of the alarm sound for it E 14 a The unit will now ask Would you like to turn off the Alarm If you say Yes the unit will reply Alarm One is Off and proceed to announce the Alarm Two settings If you say it will proceed to Alarm Two f Alarm Two check will be announced in the same way as alarm one above SNOOZE FUNCTION When the preset alarm time is reached the chosen alarm sound will start You can momentarily stop the alarm sound for 9 minutes by using the snooze function The snooze function can be repeated for a maximum of 6 times within 60 minutes from the original preset alarm time MANUAL OPERATION 1 When any alarm is sounding press the SNOOZE BAR 11 for a 9 minute snooze 2 The SNOOZE INDICATOR 28 will turn on 3 4 You can repeat snooze operation for a maximum of 6 times within When snooze expires the alarm sound will resume 60 minutes from the original preset alarm time You can cancel snooze any time by pressing the ON OFF BUTTON 12 The SNOOZE INDICATOR 28
24. tes The number you chose in step 4 will be said The sleep time chosen will also show on the display 24 and be played for the selected Sleep Time E 18 NOTE During sleep you may press the SLEEP BUTTON 10 to check the remaining sleep time When sleep sound is playing its volume can be adjusted from low to high level 1 4 by pressing the gt UP 6 or lt DOWN 4 BUTTONS The selected sleep sound volume will be displayed To change the sleep sound during sleep press the SNOOZE BAR 11 and use Play Sleep Sound voice command to change it as usual The remaining sleep time will not be affected LISTENING TO RADIO 1 Select your desired radio band using the BAND SELECTOR 7 for AM or FM 2 Press the ON OFF BUTTON 12 to turn radio on 3 Rotate the TUNING CONTROL 9 to your desired radio station according to the dial scale on the unit 4 Rotate the VOLUME CONTROL 1 to adjust to the desired output level 5 To turn off the radio press the ON OFF BUTTON 12 TIPS FOR BEST RECEPTION AM The AM antenna is located inside the cabinet of the unit If AM reception is weak change the position of unit until the internal antenna picks up the strongest signal During FM reception always keep the WIRE ANTENNA 21 fully extended for best performance However if FM reception is weak try repositioning the unit near an open window until you get the best reception
25. ume level in 60 seconds It will last for 60 minutes if uninterrupted When the alarm is sounding there will be a periodic pause in the alarm sound if you chose a nature sound Ocean Rain or Brook or the Beep for your wake alarm This is normal and the point where the unit is listening for one of the two Smart Talk commands Snooze or Alarm Off If radio is chosen as the alarm sound you will not be able to use Smart Talk commands to activate snooze or turn the alarm off This will need to be done manually by pressing either AL1 ON OFF 2 AL2 ON OFF 8 or ON FF 12 BUTTON If the latter alarm time is reached before the first sounding alarm has ended the first alarm will be instantly overridden and the new alarm session will sound for 60 minutes if uninterrupted An active alarm will always sound no matter the unit is off in sleep mode or playing through a radio external MP3 player If you choose the radio alarm but an external audio device remains to be connected to the LINE IN JACK 18 by a stereo cord not included when the alarm time is reached the beep alarm will automatically switch in to substitute the radio alarm TO CHECK THE ALARM TIME AL1 AL2 1 2 3 Start by saying the trigger word Smart Talk or press the SNOOZE BAR 11 The unit will reply Yes and will wait for your next command Say Alarm and the unit will announce the Alarm One time play a brief sample of the alarm
26. vated It can also be used in the middle to terminate certain Smart Talk commands Set Alarm Alarm Sound Sleep Time Play Sleep Sound amd Display E 10 CURRENT TIME SETTING AND REPORTING TO SET THE CURRENT TIME 1 Start by saying the trigger word Smart Talk or press the SNOOZE BAR 11 2 The unit will reply Yes and will wait for your next command 3 Say Set Time and the unit will reply Tell me the current time including AM or PM 4 Say the current time you wish to set the clock to Example to set the clock to 3 23AM say Three Twenty Three AM 5 When the time is successfully understood the unit will reply The time is and repeat the time you gave Example if you said to set the time to 3 23AM the reply will be The time is three twenty three AM 6 If the unit fails to understand the time given it will reply I m sorry didn t get that Please tell me the current time for example seven thirty five Now repeat step 4 above 7 If the unit fails to understand the time given a second time it will reply I m sorry did not understand you please start over or set the time manually If this occurs repeat steps 1 4 above again making sure you speak clearly in a normal voice and avoid pauses between words TO CHECK THE CURRENT TIME 1 Start by saying the trigger word Smart Talk or press the SNOOZE BAR 11 2 The unit will reply
27. will go off The alarm will now be off and ready to sound the next day at the preset time USING SMART TALK 1 When the designated alarm time is reached there will be a periodic pause in the alarm sound if you have chosen a nature sound Ocean Rain or Brook or the Beep for your wake alarm This is normal and during the pause is where the unit is listening for the Snooze command Note If radio is chosen as the alarm sound it will play without interruption and therefore you will not be able to use Smart Talk Snooze command to activate the snooze This will need to be done manually by pressing the SNOOZE BAR 11 E 15 Say Snooze during one of the pauses in the alarm sound to activate the 9 minute snooze If your command is correctly recognized the SNOOZE INDICATOR 28 will turn on When snooze expires the alarm sound will resume You can repeat snooze operation for a maximum of 6 times within 60 minutes from the original preset alarm time You can cancel snooze any time by saying Alarm Off or manually pressing ON OFF BUTTON 12 If you press the SLEEP BUTTON 10 once snooze and only the alarm in effect will be cancelled at once and go into sleep mode directly The desired sleep time can be adjusted by pressing the SLEEP BUTTON 10 repeatedly If the Alarm Off command is correctly recognized the unit will reply Yes and SNOOZE INDICATOR 28 wil
Download Pdf Manuals
Related Search