Home

Jenoptik 10.0Z3 User's Manual

1. Low Battery Indicator A low battery indicator Ha appears on the LCD screen when the batteries are nearly exhausted Batteries should be replaced promptly when the low batteries indicator appears Note Do not use manganese batteries Manganese batteries cannot supply sufficient power to support camera operation Replace all batteries at the same time Never mix old and new batteries Remove batteries from the camera if you do not plan on using it for more than two weeks The camera body may feel warm after extended use This is normal Important Users are not recommended to buy their own adaptor and use it on the camera as power supply INSERTING A MEMORY CARD You can use SD Card with this digital camera The memory card slot is located beneath the battery cover adjacent to the battery compartment Be sure that the camera is turned off Slide the battery cover and open it Insert the SD card as shown in the diagram Close the battery cover TON em GETTING STARTED To remove the memory card gently press on the edge of the card and release it Pull the card out and close the battery cover About Camera Memory The digital camera is equipped with internal memory If the memory card is not inserted in the camera all images and movie clips recorded by the camera will be stored in the internal memory If the memory c
2. 1 Set the camera to the Playback mode 2 Press 4 or gt to select a still image that you want to add a voice memo 3 Press the MENU button using or to select VOICE MEMO 244 and press the SET button e If the image already has the voice memo recorded the Y a Ser appears on the LCD monitor The new recording will replace the previous one 2005 10 15 15 15 4 Press the SET button to start recording for 30 seconds or press the MENU button to cancel it 5 Press the SET button again to end recording Y pad Note e The voice memo cannot be added to a movie clip or a protected image e You cannot delete only the voice memo When you delete the image the attached voice memo is also deleted Playing Back a Voice Memo 1 Set the camera to the Playback mode 4 120 2 Press 4 or to select the image that has the voice memo ra recorded The image with a voice memo recorded shows U on the LCD monitor 3 Press the SET button to play to voice memo 4 Press the MENU button to stop the voice memo or press the a SET button to pause it SET When voice memo paused press the SET button again to 2005 10 45 15 15 resume DELETING FILES Deleting a Single File 1 120 mal Single image can be deleted using the Playback Menu or pressing CN Ld a the camera button i 7 1 Set the camera to the Playback mode 2 Press the MENU button then press or to select DELETE press 3 Pre
3. Ee tle SET On MENUS 2005 1045 15 15 Hint To unlock the file press the SET button again in step 5 The On will disappear and the file is unlocked To lock unlock all files at a time 1 Set the camera to the Playback mode 2 Press the MENU button then press 4 or to select PROTECT On 3 Press A or V to select LOCK ALL or UNLOCK ALL and press the SET button e A confirmation message appears 4 Press the SET button to lock or unlock all files or press the MENU button to cancel 22 PLAYBACK EDITING IMAGES Rotating Still Images The still images can be rotated by various degrees 1 2 3 4 Set the camera to the Playback mode Press lt or to select the image you want to rotate CER the MENU button then press lt or to select ROTATE EH Press A or V to select an option and then press the SET button Press the SET button to confirm the change or press the MENU button to cancel The rotated image will be saved as a new file name Changing the Image Size The resolution of still images that had already been recorded can be changed 1 2 3 4 Set the camera to the Playback mode Press or to select the image you want to resize Press the MENU button then press 4 or gt to select RESIZE in Press A or V to select an option and then press the SET button The resized image will be saved as a new file name Note Only a large size image can
4. Photolmpression 5 Y Install Adobe Acrobat Reader 6 x View User s Guide x Visit Jenoptik Support Web Site a Gray Already installed or not y necessary to install LOT 2006 Concord Camera GmbH y 31 SOFTWARE INSTALLATION FOR WINDOWS USERS INSTALLING YOUR CAMERA DRIVER Make sure that your camera is not connected to the computer Make sure the computer is powered on and Windows 98SE ME 2000 XP is running Close any other applications or software you may be running Insert the supplied CD ROM into the CD ROM drive The installer will pop up automatically Note If the installer does not appear automatically double click My Computer and then double click the CD ROM drive Select the language Click OK oO oose Setup Lang JENOPTIK Select the language for the installation from the choices below a English Deutsch Espa ol Francais italiano Nederlands Portugu s Brasil Kk The installation screen will appear Click on Install Camera Drivers gt Welcome to the Jenoptik JD 10 023 EasyShot Setup Welcome to the JENOPTIK Jenoptik JD 10 023 EasyShot Setup se JD ce e 10 023 Cary Shot M Install Camera Drivers LII 9 Install XviD Codec Y Install Microsoft Windows Media Player 9 Y Install ArcSoft Photolmpression 5 Y Install Adobe Acrobat Reader 6 x View User s Guide Q Visit Jenoptik Support Web Site 2006 Concord C
5. our web site by clicking on Contact Us If you have questions concerning the operation of the camera or software installation please have the following information ready before you contact us Camera Information Name of camera model Camera Serial Number Computer Information Operation System Computer Maker and Model Exact Error Message Received For ArcSoft Technical Support on Photo Editing Software please contact In the USA and Canada ArcSoft Inc 46601 Fremont Blvd Fremont CA 94538 Tel 510 440 9901 Fax 510 440 1270 E mail support arcsoft com Japan ArcSoft Japan 9F 1 21 9 Higashi Gotanda Shinagawa ku Tokyo 141 0022 Japan Tel 81 3 5795 1392 Fax 81 3 5795 1397 E Mail support arcsoft jp Taiwan ArcSoft Inc Taiwan Branch Tel 886 0 2 2506 9355 Fax 886 0 2 2506 8922 E Mail support arcsoft com tw China ArcSoft Beijing Co Ltd No 6 South Capital Gym Road Beijing New Century Hotel Office Building 1060 Beijing 100044 China Tel 8610 6849 1368 Fax 8610 6849 1367 E Mail tech arcsoft com cn Europe Unit 14 Shannon Industrial Estate Shannon Co Clare Ireland Tel 353 0 61 702087 Fax 353 0 61 702001 E Mail europe arcsoft com Latin America local call only Tel Brazil 00817 200 0709 Tel Chile 800 202 797 E Mail latinsupport arcsoftsupport com 47 APPENDIX SAFETY TIPS AND MAINTENANCE Cleaning the camera body Please use a soft
6. 6 0 Click Finish to exit the wizard 42 SOFTWARE INSTALLATION FOR WINDOWS USERS USING ARCSOFT PHOTOIMPRESSION FOR WINDOWS USERS You can use Photolmpression 5 to transfer photos from the camera to your computer and or to edit enhance the photos saved on your computer Follow steps below to transfer photos 1 Connect the camera with your computer by using the supplied USB cable 2 Launch Photolmpression 5 by double clicking the icon representing the software on the desktop 2 The screen as shown in figure 1 1 appears Fig 1 1 3 Click on Removable Media 5s The screen as shown in fig 1 2 appears Fig 1 2 Fig 1 3 Fig 1 4 Click OK The photos stored in the camera will be shown Fig 1 3 Click OK to start saving the pictures onto your computer When it is completed click OK fig 1 4 When the photos are shown as fig 1 5 you can play with the photos for example to view a photo in detail to enhance the photo etc For more information please refer to the Help provided by the software o me 43 INSTALLING SOFTWARE FOR MAC USERS INSTALLING SOFTWARE FOR MAC USERS Note for Mac users If the video clips recorded with the camera cannot be viewed by using the QuickTime player bundled with your Mac system please complete the following installation steps For Mac OS 9 Users 1 Start up your computer and insert the software CD into your
7. AN EH OS A A Muslin AAA AAN 22 A PTT 22 EDINNG IMAGES meea E lA HN 23 Rotating SU TIigges ssa e aatis S aia MM a y x uh a MN Rus 23 Changing the Image SIZOiiii catis ev eV LE ete RO Ee A 23 SEUNG PROD EMO CE on s Aero ta A oou ovde etre coit RIAM is 24 SETTING WHE DP OF T OO 24 PLAYING A ASEIDESSEIOW a N ae 25 COPYING THE FILES esce ore cto eal eee Dh oe oos EEEO t euet dae E eno reete oben 25 ADVANCE SETTIN Sisa 25 ADJUSTING SOUNDS rare eaaa A A e AS AE 25 SETTING AUTO REVIEW o 26 SETTING THE POWER SAVE ich e e e ll 26 SETTING THE LANGUAGE qoo E eer hens ale ean ee ead 26 RESETTING THE FILE NUMBERS ct on rt e ocv e aeree aS 26 About the Folder amp File Name iiic ceri te Xo Sus ke n ai 26 S N Iro eM A ev rate cate NN tat inetd Leta tity IDO 27 SETTING THE TV OUT crc n 27 SETTING USB POR A E T E ARE EE EE EENEN 27 CHOOSING AX SIARTUP IMAGE reseo a a eee er v D e E mese e eset 27 FORMATTING THE MEMORY sek to 28 RESETTING TO DEFAULT SETTINGS titu a ati e E Ee EE ida 28 MAKING CONNECTIONS raiot iaa road 28 CONNEC TING THE CAMERA TOA Tiro aio ela rete 28 CONNECTING TEE CAMERA TO A DG ccc et tate e OR RD EE EET Id t a i e e coe se 29 USING tho Card Reader dac Ht v tto uto oec iba MEM oct aa aa does RM edo qaa 29 Connecting the Camera to a Computer with a USB Cable sse 29 PRINGTING PICTURES DIREQGT LY ccu xautcouseunc
8. be resize to a smaller one 23 ROTATE RIGHT 90 Lad l LEFT 90 a HORIZONTAL VERTICAL a JEX BOE BM gm aM E JONES Ce NF PLAYBACK Setting Photo Effect You can change or correct photo effect directly on the camera The changed corrected photos can then be viewed or printed directly without the need to transfer them onto computer for further photo editing or enhancement PhotoRite is an advanced image processing technology for automatic photo enhancement Photos processed with PhotoRite will have a more well balanced PhotoRite color and exposure and details in the scene can be seen more clearly Problems that PhotoRite can fix are backlit under expose poor contrast uneven illumination and color shift Set the camera to the Playback mode gt Press lt or gt to select the photo that you want to change its effect Press the MENU button then press or gt to select EFFECT Press A or V to select an option and then press the SET button The photo with the selected effect will be saved as a new file pe IIS SETTING THE DPOF The Digital Print Order Format DPOF setting allows you to select images on the memory card for printing and specify the number of print copies in advance using the camera This is extremely convenient for sending the images to a photo developing service or for printing on a direct print function compatible printer 1 Set the camera to the Playback mode 2 Press
9. computer s CD ROM driver 2 Double click JD10 v100 icon on your desktop 3 Double click DivX 5 1 1 Installer in the zip file under Mac OS9 folder to start installing the software 4 Follow the on screen instructions to complete the installation then restart your computer to ensure the successful installation 5 Copy file named XVIDDelegatePPC into Extensions folder and restart the OS For Mac OS X Users 1 Start up your computer and insert the software CD into your computer s CD ROM driver 2 Double click JD10 v100 icon on your desktop 3 Double click DivX 5 2 1 Installer in the zip file under MacOSX folder to start installing the software 4 Follow the on screen instructions to complete the installation VERSION 5 2 1 5 Copy file named XVIDDelegate component into Library es ee AEE QuickTime 44 APPENDIX APPENDIX TROUBLESHOOTING O Proson ca OO Sem patery Ue Inne wrong Reload battery in the correct direction direction The battery compartment door Make sure the battery compartment door take pictures P Memory card is not formatted The card may be detective use a new correctly card Image is not recorded The Flash is charge Wait for the flash to charge when the shutter button is pressed Memory is full Insert a new memory card E ui Flash is set to OFF Set the flash to any mode except off The camera was moving when Hold the camera steady when shooting the image
10. flash then fires again to take the actual 1e Red eye reduction image The digital camera will detect the subject brightness and use the flash only when required Flash fires every time you take a photo Always off The flash never fires even in dark situation Flash 3 Shoot the image Note The flash charging time may increase when the battery is low Using the Self timer amp Burst Use the self timer to set a delay from the time the shutter button is pressed to the time the image is shot Use the burst to record four continuous still images shooting 1 Set the camera to the y mode This function only used in still image shooting 2 Press the button to change the settings Self timer 13 RECORDING Single shot Record a single image 2 SEC The shutter release will be delay for 2 seconds 10 SEC The shutter release will be delay for 10 seconds Record two images in a shot after Double pressing the shutter release button 10 and 12 seconds 3 Shoot the image Each option automatically switches to single shot in the following situation e After each shot e When the mode switched When the camera is turned off Note When using the self timer function be sure to use a tripod or place the digital camera on a level stable surface Using the Macro mode Your camera is equipped with a macro function that allows you to focus on very close subjects In macro mode
11. ones Be sure to download important files to your computer before formatting RESETTING TO DEFAULT SETTINGS You can reset the entire menu and button operation settings to initial default 1 Set the camera to the Setup Menu 2 Press A or V to select RESET ALL X then press gt or the SET button to launch the submenu 3 Press A or V to select YES then press the SET button to reset all settings Note The following settings do not change with this procedure Date amp Time setting e Language setting TV out setting MAKING CONNECTIONS CONNECTING THE CAMERA TOA TV Vi a eo Audio O Images displayed on the camera s monitor screen can also be displayed on a television 1 Use the included audio video cable to connect the Im camera to the TV set ee 2 Set the TV input signal to Video In and Audio In al Refer to the documentation included with your TV for more information 3 Everything that would normally appear on the camera s LCD screen such as photo and video clip playback slide shows and image or video capture appears on the TV Q eco Note The camera LCD screen turns off automatically during video output 28 MAKING CONNECTIONS CONNECTING THE CAMERA TO A PC There are two ways to download files from the camera s internal memory or memory card to a computer Using the Card Reader 1 2 Copy images from the card into a directory of your byinserting the mem
12. shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product If your equipment contains easy removable batteries or accumulators please dispose these separately according to your local requirements The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city offi ce your household waste disposal service or the shop where you have purchased the product The Jenoptik trademark is used by Concord Camera Corp and its subsidiaries under license Concord and the Concord logo are registered trademarks or trademarks of Concord Camera Corp in the United States and or other countries Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries PhotoRite is a trademark of Zensis Limited PictBridge is a trademark 50 Visit Concord on the Internet www jenoptik camera com Version 1 0 586220 00 R1 JD 10 0z3 EasyShot User s Guide Copyright 2006 Concord Camera Corp
13. the MENU button using lt or gt to select DPOF 5 and press the SET button 3 Press A or V to select SINGLE then press the SET button 4 Press lt or gt to select the image you want to print out and the SET button 5 Press A or V to specify the number of copies ET The number of copies can be set from O to 30 gt To cancel this image DPOF setting set the number of copies to 0 2005 9 8 8 46 6 Press P and then press A or y to set or cancel the date stamp of current image Press the SET button to apply the setting or press the MENU button to cancel Repeat step 4 7 to set other images for printing After you finished all image settings press the MENU button to apply it 00 Y Hint To set the DPOF setting for all images in a time select ALL in step 3 and press the SET button Toreset all DPOF settings to initial default select RESET in step 3 and press the SET button 24 ADVANCE SETTINGS PLAYING A SLIDE SHOW You can set the camera to display images in a slide show 1 2 3 Set the camera to the Playback mode Press the MENU button using 4 or to select SLIDE SHOW and press the SET button Use the arrow button to set the playback interval and repeat or not 5 You can set the interval between 1 10 seconds Press the SET button to start the slideshow or press the MENU button to cancel During the slideshow press the SET button to pause the slidesh
14. the XviD Setup Wizard Setup has finished installing XviD on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup INSTALLING WINDOWS MEDIA PLAYER 9 Step Make sure that your camera is not connected to the computer Step2 Make sure the computer is powered on and Windows 98SE ME 2000 XP is running Step3 Close any other applications or software you may be running Insert the supplied CD ROM into the CD ROM drive The installer will pop up automatically Note If the installer does not appear automatically double click My Computer and then double click the CD ROM drive Select the language Click OK JENOPTIK Select the language for the installation from the choices below a English Deutsch Espa ol Francais Italiano Nederlands Portugu s Brasil EH The installation screen will appear Click on Install Microsoft Windows Media Player 9 P Welcome to the Jenoptik JD 10 023 EasyShot Setup e 2 n Welcome to the Jenoptik JD 10 023 EasyShot Setup 3D 10 023 Laryshat 3 Install Camera Drivers Install XviD Codec 2 Y Install Microsoft Windows Media Player 9 o Y Install ArcSoft Photolmpression 5 c 2 Install Adobe Acrobat Reader 6 gt e x View User s Guide e Visit Jenoptik Support Web Site a gt 2006 Concord Camera GmbH e edid Step 7 Installation stars 36
15. was captured picture Image is blurry or out l Turn the Macro mode on to ensure the of focus The subject was beyond the DTE tahaewithin which he camera subject is within 5 cm zoom out or 25 ap cm zoom in Do not use Macro mode abaco when shooting distant subjects Image is not A memory card with non DCIF displayed on the LCD images recorded with other monitor camera is loaded This camera cannot display non DCIF images The camera was turned If the battery low indicator appears on off powered down before the the LCD monitor replace the battery image was stored in memory immediately Recorded images are not saved in memory Cannot transfer images to a computer after connecting the USB cable Install the USB driver before you USB driver is not installed connect the camera to a computer turn the camera on 45 APPENDIX SPECIFICATIONS 10 13 Mega Pixels CCD Size 1 2 5 inch BH Focal Length f 7 94 22 71mm 3X optical zoom 4X digital zoom LCD monitor 2 4 TFT color LCD Poca Rande Normal 80cm Infinity 9 Macro W 5cm 100cm T 25cm 100cm Aperture F 2 8 5 1 Shutter 8 1 2000 sec Still Image JPEG EXIF 2 2 compatible DCF compatible Support DPOF File Format PictBridge available Video MPEG 4 with Audio Audio WAV Still Image 3648x2736 3648x2432 3 2 3264x2448 2560x1920 Resolution 2048x1536 640x480 Video 640x480 320x240 160x128 Aperture priority Shutter p
16. you can focus on subjects 5 cm from the lens when in the maximum wide angle zoomed out setting and 25 cm in the maximum telephoto zoomed in setting 1 Set the camera to the Il mode e You can use the macro mode in still image shooting or movie recording 2 Press the Y button to enter the macro mode The macro mode icon Y appears on the LCD monitor 3 To leave the macro mode press the Y button again Y Macro Note Distances referred to measure the distance between the camera lens surface and the subject 14 RECORDING RECORDING MOVIE CLIPS Your camera can record movie clips with audio 1 Set the camera to the Pf mode The LCD monitor displays the available recording time 2 Press the shutter to start recording 3 Press the shutter again to end recording The camera will stop recording automatically when the memory capacity has been reached 00 10 00 Note The voices of the movie clips are recorded from the microphone of the camera Be careful to avoid touching the microphone while recording The White Balance is set and locked to the settings of the first frame 00 10 00 VOICES RECORDING You can record voices using this camera 1 Set the camera to the Q mode The LCD monitor displays the available recording time 2 Press the shutter to start recording 3 Press the shutter again to end recording The camera will stop recording automatically when the memory capac
17. D 10 073 EasyShot ser s Guide www jenoptik camera com ENGLISH Table of Contents GETTING STARTED ctas A AR 3 STANDARD ACCESSORIES renes on di Ove cocus UNE eco 3 Altaching the Wrist Strap A Etpe c Padi quee eee bi sade ado 3 PIEGIEVOe T EIEEE 4 NAMES OF RAR TS sas 4 INSERTING THE BATTERIES aoii scort dd rekia DONEO Eeee E a a aeS OOE EEEE Ene ODETE EEOSE 5 LOW Battery INACIO A A TIE dad 5 INSERTING A MEMORTCA Dr pectet d uasa a AR RN D Cte c ecd de 9 About Gamera Memole rarse o o MAU i ce aas 6 DCF Prol O 6 SETTING THE DATEAND UME irrig dd Odo 6 BASIC OPERATION Socia 7 TURNINSG THE POWERON AND OFF oe aE PO eet HER eee eoe tbe canst Ns rod envers 7 POWER Saving UA CO NO 7 SWITCHING BETWEEN RECORD AND PLAYBACK ssssseeeeeennem mene nnn nennen 7 USING PHEIMENUS irme ii E E TEE 8 Recording Menus Playback MOrt i oet ta 8 ADJ Ments eid T 9 CTO Men cui ad la 9 USING THE PCB MONITOR ari a de den td do fea dd aia 11 ECDESCIOCIAMAIC RO ii do 11 owitching TREO Screen DISDIAY seio A a CE Ds Ud 11 RECORDING inin aia 12 RECORDING S MLY IMAGES teet a n e ea A teer eere 12 Using th Zoom FU HOD sod iaa er a eee Ee la cas 12 USING TO A MM fete MAE 13 USING the Selfl timer GKBUEISE ti Eds 13 USING TIE MaGIO THOS Tr A 14 RECORDING MOVIE CDS y es MUO EE ic Maa 15 VOICES i
18. ROM Drive Double click on the CD ROM Drive icon for installation and proceed to Step 5 Select the language Click OK gt Choose Setup jc fs Select the language for the installation from the choices below English ib Espa ol I Francais I Italiano P Nederlands Portugu s Brasil ox cancer 38 SOFTWARE INSTALLATION FOR WINDOWS USERS The installation screen will appear Click on Install ArcSoft Photolmpression 5 P Welcome to the Jenoptik JD 10 023 EasyShot Setup Welcome to the Jenoptik JD 10 073 EasyShot Setup Install Camera Drivers Install XviD Codec Install Microsoft Windows Media Player 9 Y Install ArcSoft Photolmpression 5 Y Install Adobe Acrobat Reader 6 y View User s Guide Visit Jenoptik Support Web Site Option Already Installed Or Not The Jenoptik trademark is used by Concord Camera Corp and its subsidiaries under license Windows Media Player is either a trademark or a registered trademark of Microsoft Corporation in the United States and or other countries All other brands and product names are either registered trademarks or trademarks of their respective ovmurs Click Next gt ArcSoft Photolmpression 5 Setup Welcome to the InstallShield Wizard for Photolmpression The InstallShield Wizard will install Photolmpression on your computer To continue click Next Click Yes ArcSoft Photolmpression 5 Setup x License Ag
19. SOFTWARE INSTALLATION FOR WINDOWS USERS Read the License Agreement then click I Accpet SUPPLEMENTAL END USER LICENSE AGREEMENT z Printable Version B 2 IMPORTANT READ CAREFULLY This Supplemental End User License Agreement Supplemental EULA is a legal agreement between you either an individual or a single entity and Microsoft Corporation Microsoft for the Microsoft software that accompanies this Supplemental EULA which includes computer software and may include associated media printed materials online or electronic documentation and Internet based services the OS Components The OS Components are provided to update supplement or replace existing Functionality of the applicable Microsoft software for which the OS Components are designed any such software referred to here as OS Software An amendment or addendum to this Supplemental EULA may accompany the O5 Components YOU AGREE TO BE BOUND BY THE TERMS OF THE APPLICABLE OS gt The screen shows installing progress bars When the installing is complete the screen shows welcome page Click Next 3 Windows Media Player 9 Series Thank you for installing the all in one media player with smart jukebox technology that makes finding organizing and recording your digital media content easier than ever During setup Windows Media Player 9 Series will be set as the default player for playing your digital media content including music videos CDs
20. Strap Attach the wrist strap to your camera as shown Note Do not swing the camera when carrying by the wrist strap GETTING STARTED Using the Soft Case When not using the digital camera keep it in the soft case for protection pee 29D Ce NAMES OF PARTS Top Front Shutter button a Flash 2 Self timer mE lamp Strap ring Q Lens Power button A Microphone zm EL E E 4 Bottom Back Zoom W button Thumbnail Zoom T button Digital zoom playback mode button MENU button Operation lamp Battery card chamber cover LCD monitor 5 function button Mode button Tripod socket DISP button Side 5 function button Scene Delete Up button Macro Left Flash Right button button s USB connector E SET ADJ Self timer Continue Down button GETTING STARTED INSERTING THE BATTERIES The camera is powered by two AA size alkaline batteries or rechargeable Ni MH min 2000 mAh 1 2V to get 250 shots batteries 1 Slide the battery cover open ooo QU WY b BATTERY oo 6 0 OPEN 7 o 2 Insert two AA size alkaline batteries with the positive and negative poles matching the directions indicated inside the battery room 3 Close the battery cover
21. T UP SOUND 3 AS SELECT OK ADVANCE SETTINGS SETTING AUTO REVIEW When Auto Review is enabled you can view an image for a few seconds after you have taken it Option Deseription The captured image will not automatically display after shooing The captured image will display for 3 seconds after shooting The captured image will display for 5 seconds after shooting SETTING THE POWER SAVE For power consumption you can set your camera to turn off automatically for a period of time Option scription O The power will turn off automatically after 1 minute The power will turn off automatically after 3 minutes The power will turn off automatically after 5 minutes SETTING THE LANGUAGE The camera can display menus and other information in a number of different languages DEN SOUNDS English ESI AUTO REVIEW Francais 1 Set the camera to the Setup Menu P 2 Press A or V to select LANGUAGE 09 then press or the EE Power SAVE Espa ol SET button to launch the submenu ES pate 8 TIME Portugu s 3 Press A or V to select a language and press SET button to apply LANGUAGE fallano E the setting 4 Press the MENU button to close the menu 44 SELECT OK RESETTING THE FILE NUMBERS Use this function if the camera experiences a Folder cannot be created error or if you want to restart numbering for example after erasing all files Resetting the file number is useful for avoiding the file name dup
22. amera GmbH The two warnings will be shown orderly Please ignore them and click OK Warning Please REMOVE your camera if it is connected Step 7 Warning A You ss need Windows Installation CD for complete install Please prepare that before i install 32 SOFTWARE INSTALLATION FOR WINDOWS USERS Click Next JD 10 023 Easy Shot Setup Version 1 00 0000 d Welcome to the InstallShield Wizard for JD 10 023 Easy Shot The InstallShield Wizard will install JD 10 023 Easy Shot on your computer To continue click Next Step9 Install progress bar To ensure the complete installation and enable the camera to function well please do select restart your computer InstallShield Wizard Complete The InstallShield Wizard has successfully installed JD 10 023 Easy Shot Before you can use the program you must restart your computer Yes want to restart my computer now C No will restart my computer later Remove any disks from their drives and then click Finish to complete setup INSTALLING XVID CODEC Note To ensure the video clips can be played please install XviD Codec Step1 Make sure that your camera is not connected to the computer Step2 Make sure the computer is powered on and Windows 98SE ME 2000 XP is running Step3 Close any other applications or software you may be running Insert the supplied CD ROM into the CD ROM drive The installer will pop up automatically Not
23. and DVDs This setup process will allow you to customize these defaults and other installation options Choose the privacy options according to your preference then click Next Windows Media Player 9 Ser Select your Privacy Options Microsoft is committed to protecting your privacy To deliver an enhanced experience data is exchanged over the Internet and may be saved on your computer Privacy Statement Enhanced Playback Experience 0 Mote information IV Retrieve media information for CDs and DVDs from the Internet about these privacy options TV Update my music files WMA and MP3 files by retrieving missing media information from the Internet IV Acquire licenses automatically For protected content Note media information retrieved may not be in your local language Enhanced Content Provider Services F Send unique Player ID to content providers To view or change privacy settings that affect cookies click Cookies Cookies Customer Experience Improvement Program T 1 want to help make Microsoft software and services even better by sending Player usage data to Microsoft History IV Save file and URL history in the Player Select or dis select the file types that will player Then click Finish 1 Windows Media Player 9 Series Customize the Installation Options Configure your desktop and Windows Media Player 9 Series default settings File Types More Options Windows Media Player 9 Series will b
24. ard is inserted images and movie clips are stored on the memory card DCF Protocol The DCF protocol defines the format for image file data as well as the directory structure for the memory card Images that are taken by a DCF camera can be viewed on DCF compatible cameras from other manufacturers SETTING THE DATE AND TIME When the camera is first turned on the date and time setting will not be correct So before using be sure to set date and time 1 Press the MENU button using or to select SETUP AS and press the SET button 2 Press A or V to select DATE amp TIME SE then press or the SET button to launch the Date amp Time screen 3 Press A or y tto change the value of the highlighted field Press lt or to highlight another field 4 After adjusting the settings press the SET or the MENU button to apply the setting Note f you hold down A or y you can change the value quickly SETUP MENU 1 3 T DNE SOUNDS El AUTO REVIEW 3 SEC E power SAVE 1 MIN E DATE amp TIME Ecl LANGUAGE ENGLISH SELECT X amm EXIT amp DATE amp TIME 2005 12 25 12 00 YYMM DD 47 SELECT OK e Ifthe batteries are removed for about two days the Date amp Time setting will be lost In this case make these settings again BASIC OPERATIONS BASIC OPERATIONS TURNING THE POWER ON AND OFF 1 Press and hold the POWER button to turn on the camera in the Record mode Or you can press t
25. background out of focus Selecting a lower aperture value allows you to soft the background Hint The larger the aperture value the smaller the lens opening allowing less light to enter the camera Using the Shutter Priority In this mode you can set a shutter speed to match the brightness Faster shutter speeds allow you to take a sharp picture of a moving subject while slower speeds create a trail effect and allow you to shoot without a flash in dark areas Hint 1 250 indicates 1 250 second And quote marks indicate the decimal place so that 0 7 indicates 0 7 second and 2 indicates 2 seconds 16 RECORDING Using the Manual mode You can manually set the shutter speed and aperture to achieve a particular effect NOTE If the image would be underexposed or overexposed and correct exposure cannot be obtained press the shutter release button halfway the exposure value display on the LCD monitor turns red Setting the Resolution and Quality You can select lower image resolution and quality to decrease the image size to capture more images Choose a suitable setting according to the desired image quality and purpose Resolution 3648x2432 Printing in 3 2 ratio 3264x2448 Suitable for printing normal size paper 2560x1920 Suitable for printing on A4 paper 2048x1536 Suitable for printing on A5 paper 640x480 Suitable for attaching to e mails or using in websites le Stores the image with an extremely low compress
26. c docu e ds raura ramus nu oae a pR ecu a 30 SOFTWARE INSTALLATION 5 2 cia 31 SYSTEM REQUIREMENTS rcu ES 31 USING THE INSTALLER SPLASH SCREEN rear tee borrado n anu n Foe an rhe ree EUR sua Farneton dido 31 INSTALLING YOUR CAMERA DRIVER dei eoe e E E o ed ee eee citt ete Rh 32 INSTALLING XVID CODE C caia ee esses eee Lo xad esee re reg oun costilla 33 INSTALLING WINDOWS MEDIA PLAYERS rarior nadien rs 36 INSTALLING ARCSOFT PHOTOIMPRESSION ocn di ee 38 INSTALLING ADOBE ACROBAT READER 3 5 rrr tot ett tu eon eoe Eat ee eaaet EEEO SE 40 USING ARCSOFT PHOTOIMPBESSIQJIg i reste Ret I p cere E e seen ved aestu DUE 43 INSTALLING SOFTWARE FOR MAC USERS ee eeseeeeeiieeee nnn nnn nnn nnn nana 44 APPENDIX dice casi vaadsbeboner a a E 45 TROUBLESHOOTING aiis E a E eee Ms a 45 SPECIERCA TO NS E a a T ede 46 GETTING HELP oe ices RR a 47 SAFETY THPS ANDMANLTEBNANGE 2 ed 48 REGULATORY INFORMATION 2 2 5 2 5 5398200 to 50 GETTING STARTED GETTING STARTED STANDARD ACCESSORIES DD O A yz Camera USB Cable Video out Cable er Soft Case Strap 2 x AA Batteries Rechargeable Software Installation CD ROM Quick Start Guide Battery charger NOTE tems marked with are available as optional accessories Note that the shape of the charger plug depends on the area where you purchased the camera Attaching the Wrist
27. d OS X Minimum 64 MB RAM USB port CD ROM drive 800x600 pixels 16 bit color display compatible monitor Specifications are subject to change without prior notice Camera Driver Enables you to download the files taken with the camera Its an ISO MPEG 4 compliant video codec and enables you to XviD Codec ife compress decompress digital video Windows Media Player 9 Enables you to playback the video clips taken with the camera Arcsoft Photoimpression 5 Enables you to edit and enhance pictures Adobe Acrobat Reader Enables you to view the electronic version of the User s Guide Direct link to the electronic version of the User s Guide in different languages All User s Guides are saved in PDF format Concord S bpbort Website Direct link to our camera support website Ensure that an internet PP connection is established before clicking on the link USING THE INSTALLER SPLASH SCREEN User s Guide The installer will automatically detect which software applications need to be installed or if they are not necessary This will be indicated by the buttons on the splash screen that appears when the CD ROM is inserted into the computer Required or highly Yellow 0 recommended to install I Welcome to the Jenoptik JD 10 023 EasyShot Setup y Welcome to the JENOPTIK Jenoptik JD 10 023 EasyShot Setup x Install Camera Drivers x Install XviD Codec Y Install Microsoft Windows Media Player 9 x Install ArcSoft amp
28. dry cloth to clean the camera Cleaning the lens and LCD 1 Blow off dirt or dust with a blower or canned air 2 Gently wipe the lens and or LCD with a micro fiber cloth 3 To remove dirt or residue moisten the cloth with lens cleaning fluid and gently wipe the lens and or LCD CAUTION Do not apply the fluid directly onto the lens or LCD Cleaning the battery contacts As a matter of routine operation and handling should any debris or foreign contaminant deposit itself on the battery contacts in the camera and or on the batteries follow steps below to clean the battery contacts to ensure proper electrical operation 1 Wet the tip of a cotton bud swab with rubbing alcohol and squeeze the excess alcohol from the bud swab 2 Wipe the battery contacts inside the camera battery compartment and both ends of the batteries lightly with the damp bud 3 Allow the contacts to dry before placing batteries in the camera Caution 1 Do not press hard during cleaning as this will cause damage to the battery contacts 2 Do not use water to clean the contacts as this will increase the chance of oxidation 3 Do not use Acetone or Nail Polish remover to clean the contacts as this may adversely affect camera operation Safety Tips Precautions for the camera Do not attempt to modify this camera in any way This may cause a fire electric shock or severe damage to the camera Do not use the flash in close proximity to people or animals e W
29. e If the installer does not appear automatically double click My Computer and then double click the CD ROM drive Select the language Click OK IF Choose Setup Lang Lx Select the language for the installation from the choices below a English Deutsch Espa ol Fran ais Italiano Nederlands Portugu s Brasil OK fl Cancel 33 SOFTWARE INSTALLATION FOR WINDOWS USERS The installation screen will appear Click on Install XviD Codec P Welcome to the Jenoptik JD 10 023 EasyShot Setup Welcome to the Jenoptik JD 10 023 EasyShot Setup Install Camera Drivers Y Install XviD Codec Y Install Microsoft Windows Media Player 9 Y Install ArcSoft Photolmpression 5 Y Install Adobe Acrobat Reader 6 x View User s Guide Visit Jenoptik Support Web Site Option Already Installed Or Not Necessary N The Jenoptik trademark is used by Concord Camera Corp and its subsidiaries under license Windows Media Player is either a trademark or a registered trademark of Microsoft Corporation in the United States and or other countries All other brands and product names are either registered trademarks or trademarks of their respective ovmurs 2006 Concord Camera GmbH S Select the language Click OK Select Setup Language xj QO Select the language to use during the installation XviD Click Next Welcome to the XviD Setup Wizard This will install XviD MPEG 4 Video Cod
30. e This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help C This product is in conformity with Directive 89 336 EEC Disposal of used Electrical amp Electronic Equipment Applicable in the European Union mms and other European countries with separate collection systems This symbol on the product or in the in the manual and in the warranty and or on its packaging indicates that this product shall not be treated as household waste Instead it
31. e light source cannot be specified Note Point the camera at a white piece of paper or similar object under the lighting conditions for which you want to set the white balance and then press the SET button Setting the ISO With the initial settings the ISO sensitivity is automatically set according to the brightness of the subject Option scription Sets the ISO sensitivity automatically ISO 50 Sets the sensitivity to ISO 50 equivalent ISO 100 Sets the sensitivity to ISO 100 equivalent ISO 200 Sets the sensitivity to ISO 200 equivalent Note Higher ISO speeds increase the image noise To take clean images use as low an ISO speed as possible Setting the Exposure Set the exposure value manually to compensate for unusual lighting conditions such as indirect indoor lighting dark backgrounds and strong backlighting 18 RECORDING Setting the Metering There are 3 different light metering options available on your camera Opin O Desepti n S O e Light is measured from the entire shooting screen but gives more importance to the values near the center Selects an exposure based on readings from multiple points in the subject area Selects an exposure based on a single reading taken from the center of your Le picture Setting the Sharpness You can select whether you want the image to have sharp or soft outlines Option Deseription O o The edges of the image are emphasized The edges w
32. e the default player for the file types that are selected in the Following list You must be logged an as an administrator or a member of the Administrators group to change these settings Description Y Windows Media Audio File wma andes fies wr v Windows Media Video file wmv extensione Y Windows Media file asf v Music CD Playback Y MP3 audio file mp3 Y Windows video File avi Y Windows audio file wav Y Movie file mpeg Y MIDI file midi M AIFF audio file aiff Y AU audio file au 37 SOFTWARE INSTALLATION FOR WINDOWS USERS The screen shows the Windows Media Player window Close the Windows Media player by clicking on the X on the left top corner or clicking File Exit Note If you have downloaded the video clips recorded with the camera onto your computer you can click File Open to view the video clips immediately INSTALLING ARCSOFT PHOTOIMPRESSION FOR ALL WINDOWS USERS OPTIONAL Step Make sure your camera is powered off and not connected to the computer Step 2 Make sure the computer is powered on and Windows is running Step3 Close any other applications or software you may be running Insert the supplied CD ROM into your computer s CD ROM drive Note If the installer does not start automatically within 30 seconds after the CD ROM has been inserted click on My Computer either on the Desktop or in the Start Menu and locate the CD
33. ec on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup Select accept the agreement then click Next gt mmm License Agreement Please read the following important information before continuing Please read the following License Agreement You must accept the terms of this agreement before continuing with the installation GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 59 Temple Place Suite 330 Boston M 02111 1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your C do not accept the agreement lt Back Cancel Click Next Information Please read the following important information before continuing When you are ready to continue with Setup click Next XviD 1 0 3 20122004 Final Release Based on CVS from 20 12 2004 08 00h MET Changelog XviD 1 0 3 20122004 xvidcore Fixed trellis optimization overflow for quant lt 2 vidcore Don t read too short streams This prevents from reading useless stream garbage vidcore Fixed 64 bit crashes because of addressing assuming 32bit integers Andre W erthman vidcore Fixed 2 diamond search bugs one was causing searches in wr
34. es mic ORE 15 SETTING THE RECORDING F NGTIONS 1 55 5 ORO OX PERI cuu helenae 15 Using the Scene ModE s tai e dd RATE 15 Using the Program MOUO ueste c oa etes tuere dod Deeds esp po Ru SUE 16 Using the Aperture POL ies tia er It ei 16 Using the Shutter PHOHLDy cette ert tuc eie caedi bert eee exe Rd aa cea 16 Using the Manual THOU NN dni 17 Setting the Resolution and Quality ocooococcconcconcconoconoconocononcnnncnnnnrnnn anna 17 oeftibg the MOVIO SIZQ 1 ete e aot ERE Reo id 17 Setting the Stabilizer us cH t e E net ned 17 Setting Ne WHE Balances T ads 18 Setting ICTS Oireann e II A 18 Setting TIE EDOS US sete A EAS ATRAE ARANA AAA tt 18 Setting MEME el Dd lls 19 Setting the SNAPE Ss a Etta Naat ld ic 19 DOHING the Photo EITeGE oed ert teet id e n ba P D e eke 19 Seti Dale SIamppisx io Me La Ead sss Ma tad ii M Lr uut 19 PLAYBACK sccundum oc ise as 20 PLAYING BACK IMAGES tene dedo uota Redde a Eu pm Es 20 Using the TRUM PNA MT 20 Magnifying and Trimming Still Images eise eiiis sessi sese eene enne nnn nnns snae 20 Playing Back Movie lt ea e te ee Rr Eee ere been HE 20 PLAYING BACK SOUNDS e cea 21 Recording a Voice METI reed a irae 21 Playing Back a Volce MENO it ete A AA ALAS TO EEE AA AA A 21 DELETING FILES e 21 Deleting a SNgle A II O henner addr seep eines te AAA ary 21 Deleting
35. etup Menu You can change the basic settings of the camera in Record mode and Playback mode 1 Press the MENU button to display the menu The menu displays depends on whether you are in the Record mode or the Playback mode Press lt or to select SETUP AT and then press the SET button to display the Setup menu Press A or y to select a menu item and then press or the SET button to launch the submenu Press A or y to select an option and press the SET button to apply the setting Press the MENU button to close the menu Quos TS BASIC OPERATIONS en em maese SSS English Spanish German French Italian Portuguese Dutch Czech Language Hungarian Polish Turkish Russian Japanese Korean S Chinese T Chinese Resets all camera settings to initial default 10 BASIC OPERATIONS USING THE LCD MONITOR The LCD monitor is used to compose images while recording adjust settings and replay images LCD Screen Indicator 1 2 3 4 5 6 In Recording 1 Mode icon 11 Aperture value 2 Flash 12 Shutter speed 3 Macro 13 Metering 4 Self timer Burst 14 Exposure 5 Zoom indicator 15 ISO 6 Battery 16 White balance 7 Storage media 17 Sharpness 8 Focus area 18 Quality 9 Shake warning 19 Resolution 10 Shots remaining 13 12 11 1 2 3 4 5 In Playback 1120 al 1 Mode icon 6 Storage media a d gt 2 Protect 7 Capture date amp time 3 Voice memo 8 DPOF Date stamp 4 File number Total 9 DPOF ind
36. f the camera while it is in process of reading writing or formatting etc SD cards are delicate electronic devices Please do not bend or drop them Please do not place the SD card in or near to an environment of strong electronic or magnetic fields such as loud speakers or TV receivers Please keep the SD card in its bag or case when not in use Its normal that the SD card is warm after use Please make sure you switch off the camera before you remove the SD card Do not open the battery memory card door or remove the SD Memory Card while the camera is reading writing or formatting the card 49 APPENDIX REGULATORY INFORMATION FC INFORMATION FCC WARNING This equipment meets the limits for a Class B digital device pursuant to Part 15 of FCC rules Only the cable supplied with the camera should be used Operation with other cables is likely to result in interference to radio and TV reception and could void the user s authorization to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesired operation Tested to comply with FCC standards for HOME OR OFFICE USE Changes or modifications not expressly approved by the manufacturer may void the user s authority to operate this equipment USER INFORMATION Not
37. he gt button to turn on the camera in the Playback mode Press the POWER button again to turn the power off Hint You can turn on the camera by pressing and holding the POWER or the gt button over 1 5 seconds Power Saving Function If the camera is turned off by Power Save feature press any button to turn it on again The Power Save feature does not work in the following situation Using the USB connector During a slideshow Recording movies or voices Playing back a video or audio file SWITCHING BETWEEN RECORD AND PLAYBACK You can switch between the Record mode and the Playback mode in following ways Press the MODE button to cycle through the still image shooting voice recording and movie recording e Press the gt button to switch to the Playback mode Note If you switch to Playback mode the lens will retract after approximately 10 seconds Capture Mode For shooting still images Voice Recording Mode For recording audio files Video Mode For shooting video clips For viewing the recorded images ye DPOUE and video clips T Power button GED Playback mode button Playback mode button BASIC OPERATIONS USING THE MENUS Recording Menu Playback Menu When a menu screen is displayed the arrow button and the SET button are used to make the desired settings 1 Press the MENU button to display the menu The menu displays depends on
38. hen taking photographs never point the lens of the camera directly into very strong light Please do not use this product in close proximity to flammable or explosive gases as this could increase the risk of explosion For safety reasons keep this product and accessories out of reach of children or animals to prevent accidents Do not swallow batteries or small camera accessories Keep the camera away from water and other liquids and never let it get wet Do not use outdoors when it is raining or snowing e Should any form of liquid enter the camera do not use it Switch the camera off and then remove the batteries Do not continue to use the camera as this may cause a fire or electric shock Do not insert or drop metallic or inflammable foreign objects into the camera through access points e g card slot and battery chamber This may cause a fire or electric shock Do not operate this camera with wet hands This could pose a risk of electric shock Under the environment with electrostatic discharge the camera may malfunction and require the user to reset the camera Under the environment with electrical fast transients EFT the camera may lose function and require user to reset the camera e Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits Please avoid using the camera in high or low temperature Operation temperature range 32 F 104 F 0 C 40 C e Itis normal that the
39. icator 9 5 Battery 10 Resolution 2005 10 15 15 15 T Switching the Screen Display Press the DISP button changes the next display mode of the LCD monitor as shown below In Record mode In Playback mode 2 1 OSD on 2 Guide line 3 OSD off 4 OSDon 5 OSD off Hint Use the Guide line mode to compose images easily before shooting images Note When the LCD display is not in OSD on press Macro Self timer Flash will change the display mode to OSD on automatically 11 RECORDING RECORDING RECORDING STILL IMAGES 1 Hold the camera with both hands and make sure the camera is stable 2 Set the camera to the y mode 3 Aim the focus area to the subject that you want to take and press the shutter release button halfway e The focus area on the LCD monitor will light green when the camera is in focus e If the shutter speed is slow or the possibility that image may be blurred the shake warning icon Nj may appear on the LCD monitor To avoid it use a tripod to stabilize the camera when recording images 4 Fully press the shutter release button to take an image Note Make sure that your fingers or the wrist strap does not block the lens e When the shutter release button is pressed halfway down check the exposure value that appears on the LCD monitor to make sure that it is appropriate for the lighting conditions Using the Zoom Function Zoom W button Thmbnail You
40. ill become sharp but noise may occur in the recording image A EN Lh a Setting the Photo Effect You can add special effects to your images in II mode Gmm Bee Note This function is not available to resolution 8M Setting Date Stamp The Date Stamp function can be used to add a date to your pictures as you take them Option scription O Do not add the recorded date amp time to printed images Only add the recorded date to printed images Date amp Time Add the recorded date amp time to printed images 19 PLAYBACK PLAYING BACK IMAGES 1 Set the camera to the Playback mode PLAYBACK 2 Press 4 to play back the previous image press gt to play back the next image Hint Holding down lt or gt scrolls images in a high speed Using the Thumbnail When in Playback mode you can view all your stored images in thumbnail format 1 Set the camera to the Playback mode 2 Press the zoom lever W a thumbnail screen is displayed 3 Use the arrow button to select the desired image and press T or the SET button to show the selected image in full screen d and Trimming Still Images Set the camera to the Playback mode Press lt or gt to select the image that you want to magnify or trimming 3 Press T to magnify the image and the central portion of the image is displayed You can use the arrow button to view different parts of the magnified image Press the MENU butt
41. ion Stores the image with a low compression x Stores the image with normal compression Setting the Movie Size Movie clips can be shot with different size DTO AO z z Setting the Stabilizer Use this function to create smooth gliding shots when you re walking or moving around reducing the camera shakes lt only works when the memory card has been inserted and the camera is ensured to set in video mode Option Description O Turn off the frame stabilizer Quality Helps you to prevent camera shake When you turn on this function the frame range becomes narrow and preview frames may not display smoothly RECORDING Setting the White Balance Adjust the white balance to match different light sources such as sunlight incandescent tungsten lighting or fluorescent lighting Opin Ion O AUTO Automatically corrects white balance Ideal for general photography Adjusts for bright sun conditions or natural light conditions Adjusts for cloudy days or twilight conditions Adjusts for normal indoor lighting conditions Corrects the orange hue of household light bulbs Ideal for indoor photos under tungsten or halogen lighting without a flash Adjusts for fluorescent lighting Corrects the green hue of fluorescent lighting a for indoor E ES ET E E under fluorescent lighting without a flash For more accurate For more accurate adjustment or when the light source cannot be specified or when th
42. ity has been reached Note The voices are recorded from the microphone of the camera Be careful to avoid touching the microphone while recording SETTING THE RECORDING FUNCTIONS Using the Scene Mode You can select from various scene mode for specific shooting conditions 1 Set the camera to the Record mode The scene mode function only used in still image shooting 2 Press the sc f button to show the Scene Mode screen 3 Use the arrow button to select a desired scene mode and press the SET button to confirm the setting 15 RECORDING ae on o sorteo Te tran ve sot meat gene The Aperture value and Shutter speed can be set manually in Blurring the background to focus on the subject Used for the wide scenic views m e v NETA Backlight Shooting the image of backlight object by changing metering a Enhance the red hue for recording sunset images Close up shooting for small subject I N Enhance the black amp white contrast Fast shutter speed to capture fast moving subjects Slow shutter speed to take fireworks exploding Using the Program Mode In this mode you can specify any settings other than the shutter speed and aperture The aperture value and shutter speed will display on the LCD monitor when you half press the shutter release button Using the Aperture Priority In this mode you can set an aperture value to match the brightness A higher aperture value brings the
43. lication when images are downloaded to a computer ption 3 DeHpion S Senes Store the latest used file number no matter deleting files or inserting a new memory card Reset file numbering each time the memory card is changed About the Folder amp File Name The digital camera automatically creates a directory of folders in the internal memory or memory card that it uses to organize still images movie clips and other information 26 ADVANCE SETTINGS File Naming File name are followed by a 4 digit number that increases in sequence File numbering starts from 0001 when a new folder is created If the highest folder number is 999 and highest file number exceeds 9999 the camera will display the warning message Folder cannot be created When it appears try one of the following ways e Reset the file number and plug in a new memory card Format the memory The folder number and file number are initialized and renumbered from 100 and 0001 respectively Note Do not change the folder and file names in the memory card using your computer It may be unable to playback the data using the digital camera SETTING THE TV OUT Your camera can be connected to a TV allowing you to preview images and movie clips on the television screen TV Out should be set to either NTSC or PAL depending on your region Opin Despon NTSC America Japan Taiwan Korea SETTING USB PORT You can set USB mode
44. nd direct sunlight when using and for when storing Do not open the battery card cover or remove the SD Memory Card while data is being read or written Do not dismantle or modify The recorded data may be lost if the card is affected by strong static electricity electrical shock during card repair or malfunction When using SD Memory Cards do not change the attributes read only etc of the files pictures JPEG or video clips AVI on the card Doing so may prevent the camera from working properly when deleting etc Do not change the file names or the directory name of the pictures or video clips using a computer or save files other than pictures or video clips taken by this camera onto the SD memory card Pictures or video clips that have been edited or added to the SD memory card with the computer may not play back and it may cause the camera to malfunction The SD Memory Card includes a write protect switch Sliding this switch downward prevents data from being written to the card and pictures and video clips saved on the card are protected Please note that pictures and video clips cannot be taken or deleted when the write protect switch is on When using a large capacity card writing reading and deleting may take some time Do not store the card in places with high humidity dusty places or where static electricity or electromagnetic fields are likely to occur Images stored in the memory card may be ruined or damaged if you turn of
45. on to return to the normal size 4 Press the SET button to set the image trimming 5 Press the SET button again to trim the selected image and save it as a new one Press the MENU button to cancel it NOTE Only still images can be magnified and trimmed d Back Movie Clips Set the camera to the Playback mode a Press lt or gt to select the movie clip that you want to playback 3 Press the SET button to start the movie e The movie clip will play on the LCD monitor 4 Press the MENU button to stop the movie or press the SET button to pause the movie e When movie clip paused press the SET button again to resume Hint e During movie playing back press to fast forward or press lt to rewind it Press the shutter button to capture the still image from the movie clip while it is paused 20 a MF as mt 5 s pM E ty Dis s s ZR Y MN 5 A i6 ade TU oec Miani Sn 2005 840 1 0 00 oD 2005 12 25 15 15 ae gt FF SET tt MENU m PLAYBACK PLAYING BACK SOUNDS Set the camera to the Playback mode Press lt or to select the audio clip that you want to playback Press the SET button to start playing the audio clip Press the MENU button to stop the audio clip or press the SET button to pause it When audio clip paused press the SET button again to resume pepe Recording a Voice Memo You can add a voice memo to the still images after you record it
46. ong directions lt Back Cancel SOFTWARE INSTALLATION FOR WINDOWS USERS Click Next Setup XviD Select Destination Location Where should XviD be installed S Setup will install XviD into the following folder To continue click Next If vou would like to select a different folder click Browse Browse At least 1 1 MB of free disk space is required Click Next gt Select Start Menu Folder Where should Setup place the program s shortcuts m Setup will create the program s shortcuts in the following Start Menu folder To continue click Next If you would like to select a different folder click Browse Browse Click Next m LEO Lx Select Additional Tasks N Which additional tasks should be performed E Select the additional tasks you would like Setup to perform while installing XviD then click Next Decoding Optio lt Back Cancel Click Install Ready to Install Setup is now ready to begin installing XviD on your computer Click Install to continue with the installation or click Back if you want to review or change any settings Destination location C Program Filest lt wiD Start Menu folder XviD Additional tasks Decoding Options Decode all supported FourCCs DivX DX50 MP4V 35 SOFTWARE INSTALLATION FOR WINDOWS USERS Step 15 Install progress bar Click Finish S Setup XviD Completing
47. ory card into a card reader by connecting the camera to a computer using the included USB cable Eject the memory from the camera and insert it in a card reader that is connected to a computer Open My Computer or Windows Explorer and double click the removable drive icon that represents the memory card choice on the computer s hard disk Note If you are using a PC card reader with a notebook computer first insert the memory card into the PC card adapter optional and then insert the PC card adapter into the computer s PC card slot Connecting the Camera to a Computer with a USB Cable 1 Install the USB software driver included with the bundled CD ROM Connect the supplied USB cable to the computer s USB port Turn on the camera The LCD screen turns off when the connection to the computer has been successfully completed Open My Computer or Windows Explorer A Removable Disk appears in the drive list Double click the Removable Disk icon to view its contents Files stored on camera are located in the folder name DCIM Note e You don t have to turn off the computer or camera when making this connection Refer to your computer s manual for information regarding the USB port location The camera will turn off automatically if the USB cable is disconnected e Windows 98SE If this is the first time the camera has been connected to the computer Windows detects the camer as an Unkno
48. ow and press the SET button again to resume SADA 3SEC i NO ME Lc 2005 1045 15 15 Note The slideshow function is not available for the movie clips and voice recording COPYING THE FILES You may want to copy the data from the camera s internal memory to the memory card for convenience WON CONDOS Be sure you had inserted a memory card to your digital camera Set the camera to the Playback mode Press the MENU button using or gt to select COPY TO CARD Ch and press the SET button Press A or V to select SINGLE then press the SET button Press lt or to select the image you want to copy to a card Press the SET button to start copy Repeat step 5 6 to copy other images Press the MENU button to complete the setting 5 120 EPA SET om MENU gt 2005 10 15 15 15 Hint To copy all images to a memory card in a time select ALL in step 4 and press the SET button ADVANCE SETTINGS ADJUSTING SOUNDS You can adjust the sound volume and set different sounds as the start up sound 1 2 3 Set the camera to the Setup Menu Press A or y to select SOUNDS uif and then press or the SET button to enter the sounds screen Use the arrow button to adjust the volume and select a desired start up sound Press the SET or the MENU button to apply the setting Press the MENU button to close the menu 25 1 SOUNDS VOLUME m al STAR
49. r ArcS H e Setup will add program icons to the Program Folder listed below You may type a new folder name or select one from the existing folders list Click Next to continue Program Folders ArcSoft Photolmpression 5 Existing Folders Online Services lt Back Cancel Step 11 The screen will show the status of the installation You can choose to install DirectX 9 or not then click Finish ArcSoft Photolmpression 5 Setup InstallShield Wizard Complete Microsoft Direct 9 or later is required to use Photolmpression Photolmpression can automatically launch the Direct installation Please be sure to restart the system before running the software for the first time INSTALLING ADOBE ACROBAT READER OPTIONAL Step1 Make sure your camera is powered off and not connected to the computer Make sure the computer is powered on and Windows is running Close any other applications or software you may be running Insert the supplied CD ROM into your computer s CD ROM drive Note If the installer does not start automatically within 30 seconds after the CD ROM has been inserted click on My Computer either on the Desktop or in the Start Menu and locate the CD ROM Drive Double click on the CD ROM Drive icon for installation and proceed to Step 5 Select the language for the installation from the choices below O English Deutsch Espa ol Francais ltaliano Nederlands Portugu s B
50. r camera has a combination of optical and digital zoom functions that allow you to zoom in on far away subjects or zoom out for a wide angle shot Zoom T button Digital zoom The optical zoom is achieved by mechanically adjusting the lens of the camera The digital zoom enlarges or shrinks the image using a software process When the zoom lever is pressed the zoom bar appears on the LCD monitor Press W to zoom out for a wide angle shot Press T to zoom in for a telephoto shot When the optical zoom factor is at maximum zooming stops temporarily Press the T again the camera switches to the digital zoom automatically and zooming continues Digital zoom works by enlarging the center portion of an image through a software interpolation process The digital zoom is used to achieve magnification levels up to approx 4 times Note Digital zoom is unavailable when recording movies 12 RECORDING Using the Flash Press flash button on the camera to set the various flash modes A symbol appears on the LCD screen to indicate the flash mode The flash cannot be used in movie recording mode 1 Set the camera to the IIl mode e The flash function is only used in still image recording mode Flash 2 Press the 4 button to change the flash mode il Flash fires automatically when shooting Auto flash z i hir conditions require extra lighting Flash strobes to let the subject s eyes adjust to the
51. rasil ox Cancel Select the language Click OK UIN JENOPTIK SOFTWARE INSTALLATION FOR WINDOWS USERS The installation screen will appear Click on Install Adobe Acrobat Reader 6 IF Welcome to the Jenoptik JD 10 023 EasyShot Setup E Welcome to the JENOPTIK de Jenoptik JD 10 023 EasyShot Setup ws Media Player S Install ArcSoft amp Photolmpression 5 Install Adobe Acrobat Reader 6 View User s Guide Y Visit Jenoptik Support Web Site AAA Ne 2006 Concord Camera GmbH y Recomposing data status bar appear Note for Win 98 SE users As Adobe Reader 6 requires Internet Explorer 5 01 or greater you may see below information ip Adobe Reader 6 0 Installer Information NE xj A Adobe Reader 6 0 requires Internet Explorer 5 01 or greater Please visit www microsoft com to upgrade Internet Explorer Note for Win 2000 users As Adobe Reader 6 need EZEzsppos the support of Win 2000 SP2 you may See below IN This version of Windows 2000 is not supported You should upgrade to Service Pack 2 and run setup again 1 1 4 Setup will now terminate information i Adobe Reader 6 0 Setup In this case please click OK to close the message screen and then click Finish to terminate the Adobe Reader 6 installation Then go to www E A microsoft com website to upg rade your system and n UN been modified To complete installation at then to install the Adobe Reader 6 again Wiza
52. rd Completed another time please run setup again Click Finish to exit the wizard If your Internet Explorer is version 5 01 or above the installation of Adobe Reader 6 will start The screen shows screen as below Click Next gt Adobe Reader 60 41 SOFTWARE INSTALLATION FOR WINDOWS USERS Click Next gt E Adobe Reader 6 0 Setup Welcome to the Setup Wizard for Adobe Reader 6 0 The Wizard will install Adobe Reader 6 0 on your computer To continue click Next WARNING This program is protected by copyright law and international treaties SES cos Click Next gt The files will be saved into C Program Files Adobe Acrobat 6 0 automatically You may change the default folder by clicking Change Destination Folder and selecting a different folder in your computer E Adobe Reader 6 0 Setup Destination Folder Click Next to install to this Folder or click Change to install to a different Folder Install Adobe Reader 6 0 to C Program Files Adobe Acrobat 6 01 Change Destination Folder Click Install to start install the Adobe Reader 6 1 Adobe Reader 6 0 Setup Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation Tf you want to review or change any of your installation Folder click Back Click Cancel to exit the wizard Click Finish Setup Wizard Completed The Wizard has successfully installed Adobe Reader
53. reement Please read the following license agreement carefully A rc S H e Press the PAGE DOWN key to see the rest of the agreement Soft End User License Agreement PLEASE READ THE FOLLOWING TERMS Agreement CAREFULLY USE OF THE SOFTWARE defined below PROVIDED BY ARCSOFT IS PERMITTED ONLY UNDER D IN ACCORDANCE WITH THIS AGREEMENT IF YOU DO NOT AGREE TO BE BOUND BY THIS AGREEMENT PLEASE DO NOT USE THIS SOFTWARE IF YOU OBTAIN THIS SOFTWARE IN FORM OF CD WITHOUT PRINT COPY OF THIS GREEMENT AND YOU DO NOT HAVE OPPORTUNITY TO READ THIS AGREEMENT YOU MAY RECEIVE A FULL REFUND OF THE ORIGINAL PURCHASE PRICE IF YOU i DO NOT USE THIS SOFTWARE AND ii RETURN IT WITH PROOF gt Do you accept all the terms of the preceding License Agreement If you choose No the setup will close To install Photolmpression you must accept this agreement InstallStiele Click Next gt ArcSoft Photolmpression 5 Setup x Choose Destination Location Select folder where Setup will install files ArcSoft Setup will install Photolmpression in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder C Program Files 4rcS oft Photolmpression 5 InstallShield 39 SOFTWARE INSTALLATION FOR WINDOWS USERS Click Next gt ArcSoft Photolmpression 5 Setup x Select Program Folder Please select a program folde
54. riority Manual Portrait Landscape Sunset Scene Mode Night Scene Text Backlight Kids Beach amp Snow Close up Sports Fireworks Sensitivity Auto ISO 50 ISO 100 ISO 200 White Balance eae Cloudy Tungsten Fluorescent H Fluorescent L Exposure Control 2EV to 2EV in 1 3 step Metering Center weighted Multi Spot Burst 4 shot snap Self timer 2 sec 10 sec Double Flash Auto Red eye reduction Always on Slow sync Always off Photo Effect Black amp White Sepia Negative Art Mosaic Storage 32MB internal memory 9 SD slot TV system NTSC PAL AA rechargeable Ni MH battery X2 AA alkaline battery X2 Operating 0 C to 40 C Storage 20 to 60 C Dimension 89 x 60 5 x 28 1 Max 32 7 lens LCD mm Power Supply Ambient temperature Weight Camera Body w o battery Approx 140 g These specifications are subject to change without notice 46 APPENDIX GETTING HELP You can get help from the troubleshooting section FAQ or Customer Support on our website Troubleshooting Section in this User s Guide Please refer to the Troubleshooting section first as it contains some of the most common problems that users encounter Website FAQ Please visit our website at www jenoptik camera com to view the Frequently Asked Questions FAQ Website Customer Support If the problem you are encountering is not listed in the FAQ section please send us an email through
55. ss A or y to select SINGLE and then press the SET button SET Qj MENU 5 4 Press d or gt to select the image you want to delete 2005 10 15 15 15 21 PLAYBACK 5 Press the SET button to delete the image or press the MENU button to cancel 6 Repeat step 4 5 to delete images Hint To quickly delete the current display image 1 Select the image you want to delete 2 Press the HW button to show a confirmation bar 3 Press the SET button to delete the current display image Deleting All Files You can use the Playback Menu to delete multiple files Set the camera to the playback mode Press the MENU button then press lt or to select DELETE ij Press A or V to select ALL and then press the SET button Press the SET button to delete all images or press the MENU button to cancel RON gt Note The protect images cannot be deleted with the delete function Protecting Files Files stored on your camera or on a memory card can be protected to prevent accidental deletion 1 Set the camera to the Playback mode LCOKALL 2 Press the MENU button then press or to select PROTECT UNLOCK ALL On 3 Press A or V to select SINGLE and then press the SET button 4 Press lt or gt to select the file you want to protect 5 Press the SET button to protect the file or press the MENU button to cancel When the file is locked the On displays on the LCD monitor 6 Repeat step 4 5 to protect images
56. temperature of the camera body rises after being in use for a long period Do not leave this camera in places subject to extremely high temperatures such as in a sealed vehicle direct sunlight or other places with extreme variances in temperature Exposure to extreme 48 APPENDIX temperatures may adversely affect the camera s internal components and could cause a fire Always use the camera and its accessories in a well ventilated area Allowing dust to accumulate in the camera over a long period of time is hazardous and in extreme circumstances may cause a fire It is best to clean your camera prior to seasonal periods of high humidity Precautions for batteries Dispose of the battery in a manner that complies with applicable laws Leakage overheating or burst battery could result in fire or injury Do not short circuit heat or dispose of batteries in fire Ensure the battery is positioned correctly with regard to polarity Battery may lose power if kept inside the camera for a long time without using Please remove the battery while the camera is not in use Batteries may not work normally under 32 F 0 C Precautions for SD Memory Cards In the event of malfunction or damage it is possible that data may be lost Concord Camera is not responsible in any way for such data loss Do not touch the terminals with hands or metal objects Keep dust water and foreign objects away from the terminal section Avoid heat liquid a
57. to connect the camera with a printer or computer Option Dewnpin O To connect your camera to a PC To connect your camera to a printer CHOOSING A STARTUP IMAGE You can choose a recorded image as the start up image 1 Set the camera to the Playback mode 2 Press or gt to select a desired image 3 Press the MENU button then press lt or gt to select S MAGE fg Press A or V to select an option and then press the SET button 4 4 5 Set the camera to the Setup Menu 6 Le S IMAGE Press A or V to select S IMAGE Kg then press gt or the SET button SELECT SET Men 7 Press A or V to select a desired image and press the SET or the MENU button to apply the setting 8 Press the MENU button to close the menu Note The start up image will not be deleted even if the original image is deleted or memory formatted 27 MAKING CONNECTIONS FORMATTING THE MEMORY To erase all data stored in the memory card if you are using a card or all data stored in the internal memory if there is no card inserted 1 Set the camera to the Setup Menu 2 Press A or y to select FORMAT 3 then press or the SET button 3 Press the SET button to start format or press the MENU button to cancel it e A BUSY PLEASE WAIT message displays and the memory card is starting format e A COMPLETED message displays when finish formatting Note All data will be deleted including protected
58. whether you are in the Record mode or the Playback mode 2 Press lt or gt to select a menu item 3 Press A or y to change the setting n playback menu press A or V to select an option and then press the SET button to display a confirmation screen or apply the setting 4 Press the MENU or the SET button to save the settings and close the menu n playback menu press the MENU button to close the menu lable Setting for still image Resolution 10M 3 2 9M 9M 3M 2M X64 Quality t qe E Metering e Le Menu tem Available Setting for movie Metering e m Le Stabilizer Off On Mena tem Avalable Seting or playa 8 BASIC OPERATIONS ADJ Menu You can quickly adjust the Aperture Value Shutter Speed White Balance ISO Exposure in Record mode 1 Press the SET button to display the menu Aperture Priority Shutter Priority can be adjusted X can not be adjusted 2 Press A or V to select a menu item 3 Press lt or to select an option 4 Press the SET button to confirm the settings and close the menu Menultem Available Setting F2 8 F3 2 F3 6 F4 0 F4 5 F5 1 F5 7 FGA 8 5 6 4 2 8 2 1 4 1 0 7 1 2 1 3 1 4 1 5 1 8 1 11 1 16 1 23 1 30 1 42 1 60 1 85 1 125 1 177 1 250 1 354 1 500 1 707 1 1000 1 1414 1 2000 AUTO 2 amp x 1 8 1 ERI RE m AUTO 50 100 200 Exposure 2 0 to 2 0 S
59. wn device and automatically completes the required software installation 29 PRINGTING PICTURES DIRECTLY PRINGTING PICTURES DIRECTLY There are two ways to print the stored pictures without the help of computer Printing Pictures by Using SD Card 1 Transfer the stored pictures from internal memory to SD card 2 Set the DPOF refer to the section Setting the DPOF 3 Insert the SD card into the SD card slot of the direct printing compatible printer 4 Refer to the instruction manual of the printer to print the pictures Printing Pictures by Using a USB Cable Set the camera to the Playback mode Press the MENU button using or to select SETUP menu and press the SET button Press A or V to select USB then press or the SET button to launch the submenu Press or y to select PRINTER and then press the SET button to apply the setting Connect the camera to the printer with the supplied USB cable The camera s LCD will show PICTBRIDGE MENU Follow the camera s on screen display and the printer s instruction manual to print the pictures prosa D 30 SOFTWARE INSTALLATION FOR WINDOWS USERS SOFTWARE INSTALLATION FOR WINDOWS USERS SYSTEM REQUIREMENTS Windows PC with processor better than MMX Pentium 233 MHz Windows XP 2000 ME 98SE Minimum 32 MB RAM USB port CD ROM drive 800x600 pixels 16 bit color display compatible monitor Macintosh e Power Mac G3 or later Mac OS 9 0 9 1 9 2 an

Jenoptik 10.0Z3 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents