Jeep 50-0283x-017 SERIES User's Manual
Contents
1. and discard 2 two screws which secure mounting bracket item 7 pg 2 to housing Insert CD changer if equipped into mounting bracket and secure in original manner using 6 six O E screws See Fig 8 FIGURE 8 10 Remove and discard 4 four screws from VCP Loosely install 4 four 8 X 3 4 screws item 1 pg 2 in those locations See Figure 9 FIGURE 9 HI INSTALLATION OF HOUSING IF VECHICLE IS NOT EQUIPPED WITH A FACTORY 10 DISC CD CHANGER PROCEED TO STEP 13 11 Install CD player and bracket over O E studs and secure using original hardware See Fig 10 12 Connect wiring to CD player FIGURE 10 5 13 Align top holes in VCP mounting bracket item 7 pg 2 with holes in vehicle See Figure 11 14 Insert 2 two well nuts item 2 pg 2 into top holes and secure using 2 10 32 x 1 screws item 3 pg 2 and 2 two 10 washers item 4 pg 2 See Figure 11 15 Secure bracket to vehicle using 4 four 10 X 1 2 screws item 5 pg 2 IF VECHICLE IS EQUIPPED WITH A FACTORY 10 DISC CD CHANGER PROCEED TO STEP 16 FIGU 2 17 Make all necessary wring connections to VCP 18 Check function of VCP See operating instructions included with components For further assistance refer to the video system manual for the technical support phone number listed for your area Align screws in VCP with slots in bracket and slide into position Make sure screws are positioned at bottom of slot See Fi2. INSTALLATION INSTRUCTIONS FOR 50 0283x 017 SERIES 1181323 50 0283x 018 SERIES 1181328 50 0283x 019 SERIES 1181325 JEEP GRAND CHEROKEE VIDEO CASSETTE PLAYER HOUSING These instructions are intended for use only by experienced professionals in the automotive customizing business Special tools and equipment as well as specialized handling and care of product during installation may be required Before beginning this installation carefully read through the following instructions Use extreme care when cutting headliner material Check for wiring or other componentry above headliner material Cut only where indicated Materials Tools required for this installation 1 2 Phillips screwdriver 2 Powered screwdriver or drill with adapter 3 1 4 hex socket bit 4 Razor knife or similar 5 10 mm deep socket 6 Pin router or similar 7 Audiovox VCP AVP 7180 or equiv MATERIALS PROVIDED FOR INSTALLATION June 7 1999 INSTALLATION INSTRUCTION 44 0033A Printed in the U S A ITEM 10 11 Description SCREW 8 X 3 4 PPH WELL NUT 10 32 SCREW 10 32 x 1 PPH WASHER 10 SCREW 10 X 1 2 HWH SCREW 8 X 9 16 PWH CD VCP MOUNTING BRACKET HOUSING MOUNTING BRKT HOUSING TOP STORAGE POCKET HOUSING BOTTOM QTY 4 1 2 2 2 3 2 4 4 a 0 3 AS 2 6 amm June 7 1999 INSTALLATION INSTRUC ONT PREPARATION OF VEHICLE INTERIOR Printed in the U S A 2 IF VECHICLE IS NOT EQUIPPED WITH A FAC
3. TORY 10 DISC CD CHANGER PROCEED TO STEP 5 FIGURE 1 Disconnect wiring from CD changer See Figure 2 Using a 10mm deep socket remove and retain 4 four 6mm nuts which secure bracket to vehicle See Figure 2 FIGURE 3 IF VECHICLE IS EQUIPPED WITH A FACTORY 10 DISC CD CHANGER PROCEED TO STEP 6 3 _ Locate the O E M CD changer housing mounted to the rear passenger side of vehicle Remove and discard 4 four screws Remove and discard housing by moving it upward and outward See Figure 1 FIGURE 2 Remove bracket from vehicle Remove and retain 6 six screws which secure CD changer to bracket See Figure 3 Lay CD changer in a safe place Discard bracket 5 Locate the O E M storage pocket mounted to the rear passenger side of vehicle Remove and discard pocket by moving it upward and outward See figure 4 FIGURE 4 Using a pin router razor knife or suitable tool carefully trim plastic panel as shown to allow clearance for VCP bracket See Figure 5 Caution Before cutting panel check for wiring or other componentry behind panel Cut only where indicated FIGURE 5 7 Install 2 two housing mounting brackets item 8 pg 2 as shown and secure using 3 three 8 X 9 16 screws item 6 pg 2 on each side See Figure 6 FIGURE 6 8 Route video and audio cables to rear passenger side VCP location See Figure 7 aCCRSSOTY controlled source FIGURE 7 9 Remove
4. gure 13 CAUTION Do not overtighten screws 19 Install housing bottom f KRE Bo 2 and carefully FIGURE 14 16 Remove and discard storage pocket item 10 pg 2 Using a razor knife carefully trim away plastic flange to allow for CD player See Figure 12 Make diagonal cuts at the corners to make it easier when breaking tabs ma i fold carpet away from each side to gain access to mounting holes Secure to VCP mounting bracket using 2 two 8 X 9 16 screws item 6 pg 2 on each side Make sure contour of housing matches floor of vehicle See Figure 14 Carefully tuck carpet behind O E plastic panel 20 Carefully install housing top item 9 pg 2 and press firmly along bottom edge to secure Velcro tape
Download Pdf Manuals
Related Search