Jasco RM24993 User's Manual
Contents
1. 5 Press and release ENTER to install the 7S code Most users will store VCR codes under the VCR button Cable codes under CABLE etc If for example you want to store a VCR code under CABLE first follow the procedure for Direct Code Entry page 8 and press CABLE in step 2 of Direct Code Entry then enter ANY VCR code in step 3 of Direct Code Entry Then follow the steps above for Code Search Note If the device does not have a CHANNEL UP button use PLAY VCR only or POWER instead Code Search starts from the currently stored three digit number under that mode Sometimes the first code that works with your device may only allow limited functionality e g the MENU button might not work There may be a code that performs more functions Continue the code search process until the best code is found 8 Code Identification The Code Identification Feature allows you to identify the 4 digit library code stored under your device key For example if you want to find out what 4 digit code is stored under your TV device key follow the six steps below 1 Press and hold the SETUP button until er the red indicator stays on Release the SETUP button 2 Press and release the desired mode button TV VCR etc The red indicator blinks then stays lit 3 Press and release the SETUP button The red indicator blinks once and SA remains lit 4 To find the first digit for D 2 3 the code stored under the m2. G 2 G 4 Press and release the numeric buttons 01 99 for the time required 4 5 6 The LED will blink off to indicate button press 7 9 acceptance 3 5 TV Sleep Timer is set 6 Leave the Remote pointing towards the TV with an unobstructed path To cancel the Sleep Timer press and hold the Sleep button until the LED blinks or press and release the Power button in TV mode 13 Troubleshooting Remote does not operate your product Press the mode button of the product you want to control Program the remote with a new code Install new batteries You might have to reprogram your remote after installing new batteries Remote may not be compatible with your product Remote does not operate some features of your product e Sometimes a particular code might operate some features but not all Try programing remote with a new code Remote may not be able to operate all features of your product or button names might be different than your product Red Indicator blinks after you program a product code e Remote did not accept the code Try to program the code again or try a different code Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or pr
3. CR control buttons operate your VCR even when the remote bd is set to operate the TV Also operates DVD Scan Note the VCR keys also control DVD when in DVD Mode Button Functions cont Red Indicator CHANNEL Up Down Lights when any Changes the channels button is pressed SLEEP enables the remote to turn off your TV after a period of 1 to 99 minutes EXIT Exit On Screen Menus and or Return to previous On Screen selection INFO button brings up DVD Display or Control Menu for Chapter Track Title number Time re maining elapsed indica tion system information etc MENU Selects the on screen 8 menu NUMBERS Enter numbers for direct channel selection Some products require ENTER to be pressed after chan nel selection S HCL ae z 5 S 3 m Z 5 m 5 OBO M ENTER For some TV models used after direct chan nel number entry to immediately ON OFF Turns change to the device On or Off selected channel Universal Note The REC button must be pressed TWICE to record from your VCR For some brands of VCRs you might need to press the REC button once then press it again for three seconds DVD Functions This remote controls many DVD functions The descriptions may vary from your original remote descriptions REW and FF buttons control the speed of Fast Forward and Reverse Playback respectively CHAN CHAN buttons respecti
4. RM24993 Universal Remote Instruction Manual 8 ER S Bi 412 TY Jaee e We 3 gt a lt O ej la 4 4 a 5 Table of Contents SLAC o a 3 Battery Installation ooonooronnnn nn 3 Battery DIVE eE E E 3 Code Saver Ta aa aa a eaa inu 3 Gode Setup aneia 3 Button Functions 2 ceeeeeeeeeeeceeceeeeeeeeeeeeeeeeeees 4 DVD FUNCIONS sini A la 6 SAT Functions siae eaaa ei aa 6 Code ENIYE AE ER 7 Direct Code Entry a sseeesssensessrnesserrrnnsrrnnneseenna 7 Code Seara none eee ieee 8 Using Your REMmOte cccccceceeceeeeeeseeeeeeeeeeeeneeees 9 Code Identification ceeeeeeeeceeeeeeeeeees 9 Shifted Functions oooronncnnn zrn 10 Controlling Devices with Power On and Off 10 Controlling Combo Devices 10 VCR DVD DVR Punch Through ioooeo o 10 Volume Mute Control and Punch Through 11 All Volume Mute Control to any one Mode 11 Setting any Mode for its own Volume Mute 12 SCC Pinoa e aaee Sohn a ai 13 TrOUDIESNOOTING erea non 14 Congratulations on your purchase of the RM24993 Universal Remote Control The RM24993 is one of the most easy to use remote controls available today With the RM24993 juggling multiple remote controls is a thing of the past Your RM24993 controls up to seven devices including the most popular brands of TV VCR DVD SAT CBL and audio equipment Note Some functions from your original remote
5. ired mode button TV VCR etc The red indicator v blinks then stays lit 3 Enter the 4 digit code from the code tables 1 on separate sheet Note after a valid 4 s code entry the red indicator turns off For an invalid code the 7 red indicator flashes 4 With your device on press ON OFF If the device turns off no further programming is required Note If some buttons do not operate your equipment try one of the other codes for your brand Write your codes down here for easy reference later En 1171 esus verax Code Search If your device does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps 1 Manually turn on the device TV VCR etc to be controlled 2 Press and hold the SETUP button until ru the red indicator stays on then release the SETUP button SHIFT 3 Press and guickly release the desired mode button TV VCR etc The red indicator blinks off once 4 Press the CHANNEL UP button lt 7 NNN repeatedly up to 300 times lt ONE gt until the device to be controlled LNY changes channel The red indicator blinks off with each button press If you accidentally overshoot the code required press the CHANNEL DOWN button to backtrack through the library until the device changes channel Pressing CHANNEL UP changes direction to forward again
6. k rapidly for three seconds if the Mode you have selected has no Volume Mute control O All other Modes will now punch through to your chosen Mode for Volume Mute control 11 Using Your Remote cont Setting any Mode to use its own Volume Mute Control This routine can set any Mode to use only its own Volume Mute control Note If your chosen Mode has no Volume Mute functions of its own then the Volume Mute buttons will do nothing 1 Press and hold the MUTE button until Press and release the desired Mode Press and release the VOLUME Press and hold the SETUP button until the red indicator turns on then release r the button di the red indicator blinks off then release the button O button TV VCR etc the red indicator blinks then stays on Down button the red indicator blinks then stays on Press and release the MUTE button and K the red indicator turns off OU Your chosen Mode will now use its own Volume Mute control 12 Using Your Remote cont Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below The remote must be in TV mode to set a Sleep Timer This feature works even if your TV does not have a sleep feature 1 Press and release the TV device button 2 Press and hold the Sleep button until the LED remains lit about 2 3 sec onds SHIFT J 3 Release the Sleep button
7. may not be controlled by this remote Use the original remote if available to control such functions Sometimes buttons other than described in these instructions may actually perform the function For example the CHAN and VOL buttons might be used to navigate through menu choices We recommend you experiment with the remote to identify if such situations pertain to your equipment The RM24993 is easy to use easy to program and it gives you total control at the touch of your fingertips 2 Battery Installation 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAA Alkaline batteries 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck in a place where the buttons remain depressed e g between the sofa cushions Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed However do not press any buttons until batteries are installed in the remote If buttons are pressed without batteries in the remote all codes will be lost Code Setup The SETUP button is used to setup the remote You can either setup the remote using the code for your brand of product from the code tables on separate sheet o
8. ode key pressed in step 2 press each numeric 4 s s key from 0 9 in turn The 0 8 8 number that causes the indicator light to blink is INPUT ENTER the first digit in your code o O 5 To find the second digit repeat step 4 6 Repeat step 4 again to find the third and fourth digits This time the red indicator turns off and stays off Using Your Remote SHIFT Press SHIFT Setup prior to the shifted key func tion e g for MENU press and release SHIFT Setup then MENU Info UP press and release SHIFT then UP Chan DOWN press and release SHIFT then DOWN Chan LEFT press and release SHIFT then LEFT Vol RIGHT press and release SHIFT then RIGHT Vol OK press and release SHIFT then OK Mute EXIT press and release SHIFT then EXIT Sleep The red indicator blinks for each keypress Controlling Devices with Separate Power On and Off Buttons Some GE RCA and ProScan models require you to press the device button for more than one second to turn the device on and the POWER button to turn the device off Controlling Combo Devices Some Combo devices e g TV VCR TV DVD DVD VCR etc will require you to set up two different Mode buttons to control both parts of the Combo device For example if you have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND a separate code under any other Mode button to control the DVD pa
9. ogramming instructions you can find available on our website www jascoproducts com 14 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 15 RM24993 3 Universal Remote aS Instruction Manual Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 Made in China RM24993 2 07
10. r you can search through the library of codes until you find a code that works for your product Please refer to Programming with Code Search page 9 for more information on using the code search feature to learn how to search through the library of codes for your products NOTE You can store any kind of code under any mode except TV I E you can store a VCR code under the CABLE button or a DVD code under the VCR button etc However you can only store TV codes under the TV button 3 Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling E G LAST may be called RECALL or ENTER may be called DISPLAY These differences depend on the brand and model of your product Also this remote can only operate features that exist on your product E G your product must have LAST ability for the LAST button to operate this feature TV DVD etc Selects prod uct to be operated VOLUME UP DOWN Changes the volume level of the product normally the TV MUTE Turns off the TV sound while the picture remains OK Selects menu items for the device you are controlling PREV CH Returns to the previously selected channel SETUP For setup SHIFT Accesses shifted functions INPUT For some TVs press repeatedly to select from available viewing sources antenna cable box VCR etc RECORD PLAY STOP ON OFF REW FF PAUSE V
11. rt VCR DVD Punch Through This remote allows the 6 VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch Through control from any Mode programmed with TV SAT or Cable codes to the last VCR or DVD programmed Mode you used This feature will not operate if the programmed TV SAT or Cable code has its own VCR transport button control e g a TV Combo SAT PVR etc 10 Using Your Remote cont Volume Mute Control and Punch Through This remote lets you select which device Mode controls your Volume Mute buttons The remote is initially set for all device Modes to use their own Volume Mute control if present If the programmed code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode Setting ALL Volume Mute Control to any one Mode This routine can set all Modes to punch through to any one chosen Mode for Volume Mute button control without the needing to change to that Mode 1 Press and hold the SETUP button until the red indicator turns on then release the button 2 Press and hold the MUTE button until the red indicator blinks off then release the button A A fe 3 Press and release the desired Mode button TV VCR etc for Volume Mute control the red indicator blinks then stays on 4 Press and release the MUTE button and the red indicator turns off The red indicator will blin
12. vely locate the succeeding or preceding Chapters or Tracks on a disc INFO button brings up DVD Display or Control Menu for Chapter Track Title number Time remain ing elapsed indication system information etc MENU brings up the DVD disc Menu screen use with the UP DOWN LEFT amp RIGHT navigation buttons OK button is used for on screen Menu selection Note some DVD players require the Play button to be used EXIT Exit On Screen Menus and or Return to pre vious On Screen selection PLAY button is used to start Disc playback and for Menu selection on some DVD players STOP button stops Disc playback PAUSE button pauses Disc playback press PLAY to resume INPUT brings up the DVD Players Setup Menu Note not all DVD Players support all the functions described above SAT Functions CHAN and CHAN buttons perform the Page and Page function for on screen Guide Menus used by some Satellite systems INFO button brings up Satellite Display screen for current Channel and system information MENU brings up the Satellite Menu screen use with the UP DOWN LEFT amp RIGHT navigation buttons OK button is used for on screen Menu selection EXIT button is used to Exit or Clear on screen Menu displays INPUT button performs the Satellite TV SAT function Direct Code Entry 1 Press and hold the SETUP button until the red indicator stays on then release the SETUP button R 2 Press and release the des
Download Pdf Manuals
Related Search