Jasco RM24945 User's Manual
Contents
1. FRONT CENTER REAR TEST LEVEL LEVEL buttons to adjust speaker levels Direct Code Entry 1 Press and hold the CODE SEARCH Cceseara button until the red indicator stays on w then release the CODE SEARCH button 3 Enter the 3 digit code 1 2 3 from the code tables cD TAPE TUNER on separate sheet 4 5 6 Note after a valid code 2 Press and release the desired device button TV VCR etc The red indicator blinks then stays lit S entry the red indicator turns off For an invalid code the red indicator flashes Cr 4 With your device on press ON OFF If the device turns off no further programming is required Note If some buttons do not operate your equipment try one of the other codes for your brand Write your codes down here for easy reference later Type stored Code VIDEOI VIDEO2 Code Search If your device does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps 1 Manually turn on the device TV VCR etc to be controlled 2 Press and hold the CODE SEARCH button until the red indicator stays on then release the CODE SEARCH button 3 Press and quickly release the desired device button TV VCR etc The red iy indicator blinks off once 4 Press the ON OFF button repeatedly up to 300 times until the device to2. Mute Control to any one Mode This routine can set all Modes to punch through to any one chosen Mode for Volume Mute button control without the needing to change to that Mode 1 Press and hold the CODE SEARCH button until the red indicator turns on then release the button 2 Press and hold the MUTE button until MUTE the red indicator blinks off then O release the button 3 Press and release the desired Mode button TV VCR etc for Volume Mute control O the red indicator blinks then stays on Lie 4 Press and release the MUTE button and the red indicator turns off The red MUTE indicator will blink rapidly for three seconds if the Mode you have selected has no Volume Mute control All other Modes will now punch through to your chosen Mode for Volume Mute control 14 Using Your Remote cont Setting any Mode to use its own Volume Mute Control This routine can set any Mode to use only its own Volume Mute control Note If your chosen Mode has no Volume Mute functions of its own then the Volume Mute buttons will do nothing 1 Press and hold the CODE SEARCH button until the red indicator turns on then release the button 2 Press and hold the MUTE button until MUTE the red indicator blinks off then release the button 3 Press and release the desired Mode Ow button TV VCR etc the red indicator blinks then stays on 4 Press and release the VOLUME erg Down button the red indicato
3. RM24945 Set Universal Remote Instruction Manual K24945 Locator Keyfob R24945 Remote Table of Contents Introduction 3 SEelUp iiccisca lola ai 3 Battery Installation 3 Battery Saver iui iaia 3 COE SAVER iii 3 Code Setup ua 3 Button Functions 4 Audio FUNGHions canina 6 AM FM Tuner and Home Theater Functions 7 Surround Sound Feature 8 Direct Code Entry ii 9 Code Search suisse nia 10 Using Your Remote 11 Code Identification nennen 11 Sleep FUNCTION renn 12 Controlling Devices with Power On and Off 13 Controlling Combo Devices 13 VCR DVD DVR Punch Through 13 Volume Mute Control and Punch Through 14 All Volume Mute Control to any one Mode 14 Setting any Mode for its own Volume Mute 15 FIND IT Operation rnnr rennene 16 Troubleshooting ias 21 Congratulations on your purchase of this 6 function FIND IT Universal Remote Control This remote is one of the most easy to use remote controls available today Now juggling multiple remote controls is a thing of the past Your Universal Remote controls up to six devices including the most popular brands of TV VCR DVD CBL and SAT It is easy to use easy to program and it gives you total control at the touch of your fingertips And when used
4. be controlled turns off The red indicator blinks off with each button press NTER E 5 Press and release ENTER to install the O code Most users will store VCR codes under the VCR button Cable codes under CABLE etc If for example you want to store a VCR code under CABLE first follow the procedure for Direct Code Entry previous page and press CABLE in step 2 of Direct Code Entry then enter ANY VCR code in step 3 of Direct Code Entry Then follow the steps above for Code Search Note Code Search starts from the currently stored three digit number under that mode Sometimes the first code that works with your device may only allow limited functionality e g the MENU button might not work There may be a code that performs more functions Continue the code search process until the best code is found 10 Using Your Remote Code Identification The Code Identification Feature allows you to identify the three digit library code stored under your device button For example if you want to find out what three digit code is stored under your TV device button follow the six steps below 1 Press and hold the CODE SEARCH button until the red indicator stays on Release the CODE SEARCH button 2 Press and release the desired device button TV VCR etc The red Ow indicator blinks then stays lit 3 Press and release the CODE SEARCH button The red indicator blinks once and remains lit 4 To find th
5. buttons CHAN CHAN may change tracks on CD Players AM FM Tuner Functions Press the AUDIO button Press the TUNER 3 button Press the AM FM button to toggle between AM and FM 4 Use the preset CHAN or CHAN buttons to move up and down channel presets WIN Home Theater Systems With GE receivers a second press of the TV button turns the receiver on _ Turn the TV on 2 Press the AUDIO button Select the audio input either by using the labeled number buttons or the FUNCTION button 4 Press the VOL or VOL buttons to control volume oO NOTE The volume buttons may operate both the TV and the receiver volume at the same time If this presents a problem it may be resolved by disabling the TV speakers by going into the TV menu Surround Sound Feature The surround sound feature may be turned ON OFF by pressing the SURR ON OFF button 1 Press the DSP ON OFF button to Press the LEVEL or LEVEL Press the SURR MODE button STOP PAUSE i until the desired mode is found Lss ue Press DELAY or DELAY to achieve the desired delay affect REW PLAY FORWARD ON DELAY DELAY DSP on off turn DSP Digital Sound Processor ON or OFF Press the DSP mode button until the gt desired effect is achieved Mode SLEEP Press the TEST button to listen to speaker levels ra Press FRONT CENTER PIE SWAP INPUT SLEEP or REAR buttons to select speakers
6. duct If the Remote does not operate some features of your device e Sometimes a particular code might operate some features but not all Try programing remote with a new code e Remote may not be able to operate all features of your product or button names might be different than your product If the Red Indicator blinks after you program a product code e Remote did not accept the code e Try to program the code again or try a different code Tips on using the FIND IT feature For best results hold the Remote with the LED pointing away from you Walk around while trying to find the item you re looking for while repeatedly pressing the appropriate button on the Remote Reduce or eliminate noises so you can hear the beeping unit you are looking for Keep the Remote away from large metal objects and other radios sources that might reduce its range as do weak batteries also 21 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of
7. e first digit for the code stored under 1 the device button pressed in step 2 4 5 6 press each numeric TV VIDEOI VIDEO2 button from 0 9 in turn The number that 8 9 causes the indicator light to blink is the 0 first digit in your code cD TAPE TUNER 5 To find the second digit repeat step 4 6 Repeat step 4 again to find the third digit This time the red indicator turns off and stays off 11 Using Your Remote cont Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below The remote must be in TV mode to seta Sleep Timer This feature works even if your TV does not have a sleep feature 1 Press and release the TV device button Ow SLEEP 2 Press and hold the Sleep button until the LED remains lit about 2 3 seconds TEST 3 Release the Sleep button 4 Press and release the 1 2 3 numeric buttons 01 cD TAPE TUNER 99 for the time 4 5 6 required The LED will 3 8 blink off to indicate button press accep 7 8 9 tance 5 TV Sleep Timer is set 6 Leave the Remote pointing towards the TV with an unobstructed path To cancel the Sleep Timer press and hold the Sleep button until the LED blinks or press and release the Power button in TV mode 12 Using Your Remote cont Controlling Devices with Separate Power On and Off Buttons Some GE RCA and ProScan models req
8. ediately goes into setup mode The LED flashes continuously to indicate that the Keyfob is ready to be set up Please see Setting the ITEM on the next page 18 FIND IT Locator Functions cont To set the ITEM for the Keyfob b Enter setup mode as on the previous page LED flashing continuously c Press a button 1 thru 6 to program the ITEM The Keyfob beeps the number of times corresponding to the ITEM Important if you used the default code of 1 for your Remote s item then you will need to set your Keyfobs to something other than 1 i e 2 thru 6 If you purchase additional keyfobs then simply follow the steps above to set them up Using the FIND IT Remote to Find Misplaced Items To find an object with a missing FIND IT Locator Keyfob attached simply press FIND on your FIND IT Remote the Remote warbles and the LED lights up release FIND then press the key 1 thru 6 corresponding to the missing unit If the object is in range the FIND IT Locator Keyfob on the missing object will begin to flash and beep You can use any Keyfob or Remote to locate any other Keyfob or Remote The maximum distance the lost item can be from the Remote is about 30 ft Therefore it may be necessary to walk to various points in your home in order for it to function 19 FIND IT Locator Functions cont Using a FIND IT Keyfob to find a misplaced FIND IT Remote To find a misplaced FIND IT Remote simply pr
9. ess the button on one of your FIND IT Keyfobs corresponding to the item you set your FIND IT Remote to 1 thru 6 If the Remote is in range it will begin to flash its LED and beep The maximum distance the lost Remote can be from the Keyfob is about 30 ft Therefore it may be necessary to walk to various points in your home in order for it to function Occasionally it may be necessary to press the number on the Keyfob more than once even when the Remote is within range due to interference or other factors Checking Your Setup To verify the ITEM of a Remote Press and hold the FIND button on the Remote then press and release button 2 then release the FIND button The LED flashes and beeps to indicate the ITEM For example if the Remote you are checking is defined as ITEM 4 you would hear 4 beeps To verify the ITEM of a Keyfob Press and hold the 5 and 6 buttons on the Keyfob simultaneously until the LED lights up then release The LED flashes and beeps to indicate the ITEM For example if the Keyfob you are checking is defined as ITEM 5 you would hear 5 beeps 20 Troubleshooting If the Remote does not operate your device TV VCR Cable Box etc e Press the device button of the product you want to control e Program the remote with a new code e Install new batteries You might have to reprogram your remote after installing new batteries e Remote may not be compatible with your pro
10. incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or programming instructions you can find available on our website www jascoproducts com 22 FCC Statement The FCC wants you to know This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturers instructions it may cause interference to radio and television reception It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub Parts B and C of Part 15 of FCC Rule
11. product normally the TV CODE SEARCH For setup 0 9 Enter numbers for direct channel selection Some products require ENTER to be pressed after channel selection TAPE TUNER ENTER For some TV models used after direct channel number entry to immediately change to the selected channel FUNCTION ne RECORD Ce DELAY UO OL O 3 g PAUSE ON OFF SURR MODE I SLEEP 5 oad PIP SWAP INPUT PIP and SWAP operate your TV s Picture in Picture features INPUT selects the video input of your TV 3 Universal Button Functions cont ON OFF Turns product On or Off Navigation buttons and SELECT used to move through on screen menuing and guides With some DBS models the DISP button should be used to select the highlighted item Use the navigation buttons to move the highlighted choice up down left or right O 0 A SAT CBL AUDIO DVD DISP Display button shows date and time if your TV or VCR has that feature CLEAR Removes the on screen display to return to normal viewing PREV CH Returns to the previously selected channel CHANNEL Up Down Changes the channels TRACK controls DVD CD track selection i e DVD CD Track Skip Up Down in DVD and CD modes ENTER TV YCR PLAY EF ON S Or STOP PAUSE SWAP INPUT SLEE TV VCR Operates the same as the TV VCR or antenna keys on your original remote
12. r 4 blinks then stays on O MUTE Your chosen Mode will now use its own Volume Mute control 5 Press and release the MUTE button and the red indicator turns off 15 Using the FIND IT Locator Functions You can use the FIND IT remote to find the Keyfob whether it has keys attached or if it s attached to something else Or you can use the Keyfob to find your misplaced Remote The Keyfob and the Remote are a set and need to be programmed to find each other Here are the simple steps 1 Insert the Batteries in the Remote Insert 2 AAA alkaline batteries in the battery compartment on the back of the Remote Observe the and notations FIND For setup and for finding up to 6 items RECORD STOP PAUSE me ee ae Universal 16 FIND IT Locator Functions cont 2 Set the ITEM for the Remote NOTE The remote is automatically set as 1 This means to find the lost Remote just press 1 on the Keyfob and the Remote should start beeping Wait about 20 seconds after inserting the batteries before testing it Should the Remote not automatically default to 1 or if you wish to change the Remote to Item 2 3 4 5 or 6 then follow the steps below To change the setting a Press and hold the FIND button and then press and release the 1 button on the Remote The Remote beeps and the LED continues to blink b While holding the FIND button press the 1 2 3 4 5 or 6 on the Remote s ke
13. s FRONT CENTER REAR Universal TEST SLEEP enables the remote to turn off your TV after a period of 1 to 99 minutes RECORD PLAY STOP REW FF PAUSE VCR control buttons operate your VCR even when the remote is set to operate the TV Also operates DVD Scan Note the VCR keys also control similar functions of your DVD player when in DVD Mode Note The REC button must be pressed TWICE to record from your VCR For some brands of VCRs you might need to press the REC button once then press it again for three seconds 5 Audio Button Descriptions Press the AUDIO device button to enable the AUDIO MODE Audio functions are indicated by the blue button descriptions LEVEL LEVEL Sets the level of the speakers during test tone mode DSP ON OFF Enables the receiver s Digital Sound Processing mode DSP MODE When the DSP mode is enabled pressing this button lets you toggle through the various DSP modes CD TAPE TUNER TV VIDEO Used to directly select the device you want to control Works in AUDIO mode AM FM Lets you select the AM FM band on your audio receiver FUNCTION Toggles the different audio input devices The number buttons also select the function labels below the buttons when in AUDIO mode DELAY ON DELAY Increases or decreases the delay between the surround and main speakers when the receiver is in surround sound mode ON OFF SURR MODE Toggles the surround modes on and off SURR MODE
14. s which are designed to provide reasonable protection against such interference ina residential installation However there is no guarantee that interference will not occur ina particular installation If this equipment does cause interference to radio or television reception which can be determined by unplugging the equipment try to correct the interference by one or more of the following measures e Reorient the antenna of the radio TV experiencing the interference e Relocate the equipment with respect to the radio TV e Move the equipment away from the radio TV e Plug the equipment into an outlet on a different electrical circuit from the radio TV experiencing the interference e Ifmecessary consult your local dealer for additional suggestions The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifica tions to this equipment Such modifications could void the user s authority to operate the equipment 23 RM24945 Set Universal Remote Instruction Manual Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 Made in China RM24945 09 05
15. sing the code tables on separate sheet or you can search through the library of codes until you find a code that works for your product Please refer to Code Search on page 10 for more information on using the code search feature to learn how to search through the library of codes for your products NOTE You can store any kind of code under any mode except TV I E you can store a VCR code under the CBL button or a Cable code under the DVD button etc However you can only store TV codes under the TV button 3 Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling E G PREV CH may be called RECALL or CLEAR may be called EXIT These differences depend on the brand and model of your product Also this remote can only operate features that exist on your product E G your product must have previous channel ability for the PREV CH button to operate this feature GUIDE displays TV VCR etc satellite or cable Selects product to on screen be operated program guide Red Indicator Lights when any button is pressed MENU PROG Brings up the main menu If you are ready in the menu system press SELECT to select a highlighted choice Use the arrow buttons to move through the menu selections MUTE Turns off the TV sound while the picture remains VOLUME UP DOWN Changes the volume level of the
16. toggles through the receiver s various surround sound mode settings FRONT CENTER REAR TEST Adjusts the levels of the front center and rear speakers respectively The test tone must be enabled first by pressing the TEST button PRESET Used to operate preset channels while in the AUDIO mode Operating Audio Functions Note Not all functions work for all brands Turning on the Receiver or Mini System Point the remote control at the receiver and press the AUDIO button The receiver should turn on In some cases you might need to press the AUDIO button and then the ON OFF button to turn the system on Selecting a device Input Device inputs such as CD Player or Tape Deck may be selected depending on the features of your receiver or mini system Input selection may be made either by pressing the labeled number function or by pressing the FUNCTION button to toggle through the inputs available on your system 6 Audio Functions cont Using the number buttons to change audio inputs To select a device press the number button 1 6 that corresponds to the device you want to operate CD TAPE TUNER TV or VIDEO Using the function buttons to change audio devices To select a device press the FUNCTION button until the input you want to operate appears on your system Operating a CD player or Tape Deck Use the Play Forward Reverse Record Stop and Pause buttons for CD Players and Tape Decks In some case the Preset
17. uire you to press the device button for more than one second to turn the device on and the ON OFF button to turn the device off Controlling Combo Devices Some Combo devices e g TV VCR TV DVD DVD VCR etc will require you to set up two different Mode buttons to control both parts of the Combo device For example if you have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND a separate code under any other Mode button to control the DVD part VCR DVD Punch Through This remote allows the 6 VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch Through control from any Mode programmed with TV SAT or Cable codes to the last VCR or DVD programmed Mode you used This feature will not operate if the programmed TV SAT or Cable code has its own VCR transport button control e g a TV Combo SAT PVR etc 13 Using Your Remote cont Volume Mute Control and Punch Through This remote lets you select which device Mode controls your Volume Mute buttons The remote is initially set for all device Modes to use their own Volume Mute control if present If the programmed code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode Any Mode chosen for Volume Mute control MUST have its own Volume Mute function or the Volume Mute buttons will do nothing Setting ALL Volume
18. with the Locator Keyfob you can easily find your misplaced Remote or any item attached to the Keyfob Note Some functions from your original Remote may not be controlled by this remote Use the original remote if available to control such functions Sometimes buttons other than described in these instructions may actually perform the function For example the CHAN and VOL buttons might be used to navigate through menu choices We recommend you experiment with the remote to identify if such situations pertain to your equipment 2 Battery Installation for Remote Control 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAA Alkaline batteries not included 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck ina place where the buttons remain depressed e g between the sofa cushions Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed However do not press any buttons until batteries are installed in the remote If buttons are pressed without batteries in the remote all codes will be lost Code Setup The CODE SEARCH button is used to set up the remote You can either set up the remote u
19. ypad whatever number you wish to assign to the Remote and release both buttons The LED blinks and the Remote beeps the number of times correspond ing to the number you pressed on the Remote The Remote is now assigned as that number c Test it by pressing on the Keyfob the number that you just set the Remote to For example if you pressed the 6 in step b above then press 6 on the Keyfob The Remote should start beeping Notes A Keyfob or a Remote cannot find a Remote or a Keyfob that is set to the same code as itself After setting the ITEM wait about 20 seconds before testing the FIND IT Remote Removing the batteries will cause your Remote to lose its setting it will revert to ITEM 1 If you want to change its settings you will need to reprogram it using the steps above 17 FIND IT Locator Functions cont 3 Set the ITEM for the Keyfob a Remove the plastic tab from the battery compartment The Keyfob beeps and immediately goes into setup mode The LED blinks continuously to indicate that the Keyfob is ready to be set up To enter the setup mode at any other time press and hold the 1 and 3 buttons simultaneously for about 3 seconds A warble beep is emitted and the LED flashes SULL continuously To Replace the Battery e Open the battery compartment on the back e Insert the battery with the positive side up e Close the battery compartment The Keyfob beeps and imm
Download Pdf Manuals
Related Search