Jasco RM24930 User's Manual
Contents
1. MENU Enters Menu mode CHANNEL UP DOWN Cursor Up Down for Menu navigation VOLUME UP DOWN Cursor Right Left for Menu navigation MUTE OK command for Menu selections Press TV or any other Device key to Exit Clear or Quit the Device Menu and return the remote to normal operation red indicator will turn off For certain RCA GE and ProScan devices pushing the MENU button selects the highlighted item The numeric buttons may also be used to select the MENU choice Note Some functions in some brands might not be fully supported Direct Code Entry 1 Press and hold the SETUP button until SETUP the red indicator stays on then release the SETUP button 2 Press and release the desired device button TV VCR etc The red indicator blinks then stays lit O 000 000 000 4 With your device on press ON OFF ON OFF Ifthe device turns off no further programming is required Note If some buttons do not operate your equipment try one of the other codes for your brand 3 Enter the 4 digit code from the code tables on separate sheet Note after a valid code entry the red indicator turns off For an invalid code the red indicator flashes Write your codes down here for easy reference later Code Search If your device does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps 1 Manually turn on2. functions Sometimes buttons other than described in these instructions may actually perform the function For example the CHAN and VOL buttons might be used to navigate through menu choices We recommend you experiment with the remote to identify if such situations pertain to your equipment 2 Battery Installation 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAAAlkaline batteries 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck in a place where the buttons remain depressed e g between the sofa cushions Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed However do not press any buttons until batteries are installed in the remote If buttons are pressed without batteries in the remote all codes will be lost SETUP Code Setup The SETUP button is used to setup the remote You can either setup the remote using the code tables on separate sheet or you can search through the library of codes until you find a code that works for your product Please refer to Code Search on page 8 for more information on using the code search feature to learn how to search through the library
3. the device TV VCR etc to be controlled Press and hold the SETUP button until SETUP Using Your Remote Code Identification The Code Identification Feature allows you to identify the four digit library code stored under your device button For example ifyou want to find out what four digit code is stored under your TV device button follow the six steps below 1 Press and hold the sETUP button until the red indicator stays on then release the sETUP button 3 Press and guickly release the desired Iv device button TV VCR etc The red indicator blinks off once 4 Press the ON OFF button repeatedly ON OFF up to 300 times until the device to be controlled turns off The red indicator blinks off with each button press ENTER 5 Press and release ENTER to install the code Most users will store VCR codes under the VCR button Cable codes under CABLE etc If for example you want to store a VCR code under DVD AUX first follow the procedure for Direct Code Entry previous page and press DVD AUX in step 2 of Direct Code Entry then enter ANY VCR code in step 3 of Direct Code Entry Then follow the steps above for Code Search Note Code Search starts from the currently stored four digit number under that mode Sometimes the first code that works with your device may only allow limited functionality e g the MENU button might not work There may be a code that performs more functions Continue the
4. RM24930 Universal Remote Instruction Manual Table of Contents Introduction Ban 3 eo A EVE DIJO 3 Battery Installation 3 Battery Saver une 3 Code SAVER i 3 Code Setup 3 Button FUNCUONS u 4 Menu Operation 6 Direct Code EMY u aaa 7 Code Search 8 Using Your Remote 4sssnn 00H nennen 9 Code Identification 9 Sleep FUNCION ia sani tds 10 Controlling Devices with Power On and Off 11 Controlling Combo Devices 11 VCR DVD DVR Punch Through 11 Volume Mute Control and Punch Through 12 All Volume Mute Control to any one Mode 12 Setting any Mode for its own Volume Mute 13 Troubleshooting 224444ennsssnnnnnnnnne seen 14 Congratulations on your purchase ofthe RM24930 Universal Remote Control The RM24930 is one of the most easy to use remote controls available today With the RM24930 juggling multiple remote controls is a thing of the past Your RM24930 controls up to four devices including the most popular brands of TV VCR DVD CBL and SAT The RM24930 is easy to use easy to program and it gives you total control at the touch of your fingertips Note Some functions from your original remote may not be controlled by this remote Use the original remote if available to control such
5. code search process until the best code is found To find the first digit for SETUP the red indicator stays on Release the O SETUP button Press and release the desired device TV button TV VCR etc The red indicator blinks then stays lit Press and release the SETUP button SETUP The red indicator blinks once and remains lit the code stored under the device button pressed in step 2 press each numeric button from 0 9 in turn The number that causes the indicator light to blink is the first digit in your code To find the second digit repeat step 4 Repeat step 4 to find the third and fourth digit This time the red indicator turns off and stays off Using Your Remote cont Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below The remote must be in TV mode to seta Sleep Timer This feature works even if your TV does not have a sleep feature 1 Press and release the TV device button O 2 Press and hold the Sleep button until the LED remains lit about 2 3 seconds 3 Release the Sleep button O required The LED will 4 5 6 blink off to indicate button press accep noe 000 5 TV Sleep Timer is set 6 Leave the Remote pointing towards the TV with an unobstructed path 4 Press and release the numeric buttons 01 99 for the time To cancel the Sleep Timer press and hold the Sleep button until th
6. e LED blinks or press and release the Power button in TV mode 10 Using Your Remote cont Controlling Devices with Separate Power On and Off Buttons Some GE RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ONeOFF button to turn the device off Controlling Combo Devices Some Combo devices e g TV VCR TV DVD DVD VCR etc will reguire you to set up two different Mode buttons to control both parts ofthe Combo device For example ifyou have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND a separate code under any other Mode button to control the DVD part VCR DVD Punch Through This remote allows the 6 VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch Through control from any Mode programmed with TV SAT or Cable codes to the last VCR or DVD programmed Mode you used This feature will not operate if the programmed TV SAT or Cable code has its own VCR transport button control e g a TV Combo SAT PVR etc 11 Using Your Remote cont Using Your Remote cont Volume Mute Control and Punch Setting any Mode to use its own Through Volume Mute Control This remote lets you select which device Mode This routine can set any Mode to use only its own controls your Volume Mute buttons The remote is Volume Mute control Note If your chosen Mode initially set for all device Modes t
7. me Mute control the red indicator blinks then stays on 4 Press and release the MUTE button and PONE the red indicator turns off The red indicator will blink rapidly for three seconds if the Mode you have selected has no Volume Mute control All other Modes will now punch through to your chosen Mode for Volume Mute control 12 13 Troubleshooting Remote does not operate your product Press the device button of the product you want to control Program the remote with a new code Install new batteries You might have to reprogram your remote after installing new batteries Remote may not be compatible with your product Remote does not operate some features of your product Sometimes a particular code might operate some features but not all Try programing remote with a new code Remote may not be able to operate all features of your product or button names might be different than your product Red Indicator blinks after you program a product code Remote did not accept the code Tryto program the code again or try a different code Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or programming instructions you can find available on our websi
8. o use their own has no Volume Mute functions of its own then the Volume Mute control if present If the programmed Volume Mute buttons will do nothing code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode 1 Press and hold the SETUP button until the red indicator turns on then release the button n m 4 Cc kJ Z Cc I m 2 Press and hold the MUTE button until Any Mode chosen for Volume Mute control o e l the red indicator blinks off then release MUST have its own Volume Mute function or O the Volume Mute buttons will do nothing the button 3 Press and release the desired Mode p4 Setting ALL Volume Mute Control to button TV VCR etc the red indicator O any one Mode blinks then stays on This routine can set all Modes to punch through to 4 Press and release the VOLUME any one chosen Mode for Volume Mute button Down button the red indicator blinks control without the needing to change to that Mode then stays on 1 Press and hold the SETUP button until SETUP the red indicator turns on then release 5 Press and release the MUTE buttonand the button the red indicator turns off 2 Press and hold the MUTE button untilthe MeV Your chosen Mode will now use its own Volume TRR NE blinks off then release the Mute control utton 3 Press and release the desired Mode button sa TV VCR etc for Volu
9. of codes for your products NOTE You can store any kind of code under any mode except TV I E you can store a VCR code under the CBL SAT button or a Cable code under the DVD AUX button etc However you can only store TV codes under the TV button 3 Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling E G PREV CH may be called RECALL or ENTER may be called DISPLAY These differences depend on the brand and model of your product Also this remote can only operate features that exist on your product E G your product must have PREV CH ability for the PREV CH button to operate this feature Red Indicator Lights when any button is pressed TV CBL SAT VCR DVD AUX Selects product to be operated PREV CH Returns to the previously selected chamnel INFO Shows the date and time if your TV or VCR has that feature Works the same way as a Display button MENU Brings up device Main Menu Use Chan and Vol buttons as cursor buttons and Mute as Okay o war Press TV to Exit ENTER 5 Used to complete S channels selection for some brands of TV Also used to complete the 4 code entry process REVERSE lt OD RECORD PLAY STOP REW FF PAUSE VCR control buttons operate your VCR even when the remote is set to operate the TV Also operates DVD Scan Note the VCR but
10. te www jascoproducts com 14 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to conseguential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or conseguential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 15 RM24930 Universal Remote Instruction Manual Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 Made in China RM24930 02 05
11. tons also control DVD when in DVD Mode Universal Button Functions cont ON OFF Turns product On or Off SETUP Used to setup the remote and for code search function SLEEP enables the remote to turn off your TV after a period of 1 to 99 minutes MUTE Turns off the TV sound while the picture remains SETUP TV CBL SAT VCR DVD AUX O DOT PREV CH VOLUME UP DOWN Changes the volume level of the product normally the TV CHANNEL Up Down Changes the channels The Channel buttons also control DVD SKIP functions INPUT Selects the video inputs of your TV if equipped with that feature 0 9 Enter numbers for direct channel selection Some products require ENTER to be pressed after channel selection TVIVCR gt REVERSE Pi S za o PAUSE JA 90v 0 TV VCR Operates the TV VCR function of your VCR Universal Note The REC button must be pressed TWICE to record from your VCR For some brands of VCRs you might need to press the REC button once then press it again for three seconds Menu Operation The Menu button puts the remote in and out of Menu Mode Pressing Menu brings up your device Menu While in Menu mode the remote s red indicator light blinks continuously The remote will exit Menu Mode after 20 seconds if no keys are pressed When in Menu Mode the Menu Channel Volume Mute and Device keys operate as follows
Download Pdf Manuals
Related Search