Jasco 45265 Instruction Manual
Contents
1. 5 Locate Horizontal Mount Extension Tube with extension jumper wire Horizontal Mount Extension Tube with Jumper Wire 6 Connect jumper wire to wire coming from LED Motion Tracking fixture Insert extension tube onto fixture knuckle Secure with extension tube screws provided See Fig 6 15 7 Connect wire coming from mounting base to wire coming from extension tube Insert extension tube into mounting base taking care to not pinch ex tension wire When properly inserted the extension tube will snap into place See Fig 7A Tighten screw on securing collar until snug See Fig 7B Do not over tighten 14 POWER UP When the power is turned on to the fixture the front lights will turn on and the light housing will rotate to the far left and then to the far right It will then rest at the center position The bottom Perimeter LEDs will begin blinking This indicates the fixture is in a warm up period this allows the motion sen sors time begin detecting the surrounding area During the warm up period the fixture will not detect movement or respond to any commands from the remote control When the bottom LEDs stop blinking the fixture will be set into AUTO security Mode and start operating SET UP AND OPERATION The LED Motion Tracking Spot Light has three individual motion Front Motion sensors two adjustable sensors Sensor located on2. is equal in size to the left and right detection zones The total detection range with the both sensors in the Narrow position is up to 150 When the adjustable sensors are set to the Wide position more emphasis is given to the far left and far right detection zones The center zone becomes smaller The Motion tracking light will continue to track movement across the center zone but there will be a slight delay before light moves to the center position The total detection range with both sensors in the Narrow position is up to 180 16 Narrow Position sensors positioned together large overlap CN Combined Sensors detection Right zone Ps detection Center w A 4 G detection zone Combined Sensors Left ZA Right detection detection zone zone detectioh zone Both motion sensors can be adjusted together within a 240 range This field of view allows the maximum adjustment for the distance the light housing will rotate Within this field of view the motion sensors can be set to the narrow or wide positions The light housing will rotate only as far as the outside edge of each sensor ty HOW DOES MOTION DETECTION WORK Motion sensors are actually heat sensors Motion Sensors detect motion by monitoring changes in heat within the detection area As a person enters the detection area the sensor compares the outside temperature with the body temperature of the person within the de
3. not move TEST MODE 2 After you have completed the sensor angle set up point the remote at the IR window located in front of the fixture Press and hold the TEST button until the light housing begins to rotate and release the button The light housing will rotate to the far left then to the far right and rest in the center position The red indicator light will blink slowly In TEST Mode 2 the fixture will begin motion tracking with the lights on regardless of daylight levels This will allow you to make minor adjustments to the sensors as well as the angle of the fixture PLACING FIXTURE IN AUTOMATIC SECURITY MODE Point the remote at the IR window located in front of the fixture Press and hold the AUTO button until the light housing begins to rotate and release the button The fixture is now in Automatic Security Mode In this mode the sensors are active and the light housing will track motion but the lights will not turn on during daylight hours However the fixture will continue to detect for motion and the light housing will continue to rotate in the direction of the movement The red indicator on the front will begin blinking at a medium rate to indicate the motion tracking light is operating law 19 MANUAL Recreational MODE After dusk the light fixture can be taken out of AUTO security motion tracking mode and placed into temporary manual mode This will allow you to point the light housing in a specific dir
4. 5pm Central Standard Time Zone WARNING Turn power off at circuit breaker or fuse box Do Not rely on a wall switch alone to turn off power Consult a local licensed electrician or electrical contractor if you are not sure about the installation Always install wiring connections in accordance with local code ordinances and National Electric Code Risk of electric shock Turn power off before servicing see instructions Ensure that no bare wires are exposed outside the electrical connections Risk of injury LED light output is strong enough to injure human eyes Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds Some metal parts in the fixture may have sharp edges To prevent cuts and scrapes wear gloves when handling the parts Account for small parts and destroy packing material as these may be hazardous to children Risk of fire Minimum 90 C supply conductors No serviceable parts Non replaceable LEDs INSTALLATION Select an existing outdoor light fixture either wall or eave mount for replace ment The fixture must be connected to 120v 60hz power source MOUNTING PREPARATION FOR THE LED SPOT LIGHT FIXTURE For maximum flexibility the LED Security light can be mounted on a wall vertical or under the eave horizontal Wall Mount Eave Mount LED Security Spotlight Features
5. MOTION TRACKING LED Security Spotlight User Manual www jascoproducts com 1 800 654 8483 TABLE OF CONTENTS Parts List Questions Missing Parts Installation Wall mount Installation Eave mount Power up set up and Operation Motion detection Set up Narrow position vs Wide position How Does Motion detection Work Test Mode Manual Mode Auto Security Mode Adjusting Light Levels Perimeter Motion Detection FCC Statement Warning Statement 6 9 10 13 14 15 17 17 19 19 19 19 20 21 Thank you for purchasing the GE Motion Tracking LED Security Spotlight Activation control This economical energy efficient outdoor LED light has been designed to allow easy installation flexible mounting options and provide exceptional light output with minimum power consumption Please read all the Instructions carefully Keep them for future reference PARTS LIST Before installing please ensure all the following items are included in the package Motion Tracking Light Mounting Base 2 Mounting Screws 2 Wire Connectors a ll ag Gasket Horizontal Mount Extension Tube Remote Control and Extension Tube Screws 4 TOOLS NEEDED Phillips head screwdriver 2 p Questions Problems Missing Parts If you have any questions regarding the installation or operation of the product Before returning to Retailer please contact Technical Support at 1 800 654 8483 option 4 Monday thru Friday 8am
6. Rotating Light ee LED Heat Sink Housing Mounting Base LED Lights 4 Thumb Screw g Decoy Camera and os B Red Indicator LED Mounting Holes Dual Motion Sensors Securing Collar Collar Screw Bottom mount LEDs po eee and Motion sensor Adjustment Knuckle WARNING Turn power off at circuit breaker or fuse box Do Not rely on a wall switch alone to turn off power VERTICAL WALL MOUNT AND WIRE CONNECTION 1 Remove the existing light fixture and disconnect house wires black white and ground See Fig 1 2 Route black and white wires coming from back of mounting base through the bottom hole of the gasket See Fig 2 Align the two mounting screw holes on the gasket to the two mounting screw holes on the mounting base and press the gasket flush to the mounting base 3 Locate black and white wires coming from back of mounting base Strip wires 3 8 9 5mm if not previously stripped Hold BLACK house wire and BLACK fixture wire together with ends even Align any frayed strands or conductors Push wires into wire nut and screw Clockwise until two twists arevisible in the wires See Fig 3 Repeat above procedure for both the WHITE house wire and the WHITE fixture wire Black to Black Note The Motion Tracking Spot Light does not utilize a house ground wire because of the plastic material of the mounting base The house ground wire does not attach to the mounting base If a house ground wire i
7. Such modifications could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica tions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 22 FIVE YEAR LIMITED WARRANTY Jasco Products Company warrants this product to be free from manufacturing defects for a period of five years from the original date of consumer purchase This warranty Is limited to the repair or replacement of this product only and does not extend to consequential
8. ection and the lights will remain on until daylight or if returned to AUTO mode To place fixture into Manual mode point the remote at the IR window in front of the fixture Press and hold either the left arrow lt or the right arrow gt to move the light housing to the desired position The fixture will return to AUTO mode when daylight is detected AUTO Security Motion tracking MODE The light fixture can be placed into AUTO mode at any time except during initial power up When the fixture is set in Auto mode it will detect motion in front of the fixture provided it is within range of either adjustable sensor Once motion is detected it will begin tracking movement To place fixture into AUTO mode point the remote at the IR window in front of the fixture Press the AUTO button After the fixture receives the command the light housing will rotate to the far left and then to the far right Release the button and the fixture will pause at the center position and wait for movement to be detected The red LED in front will continue to blink at a medium rate when the fixture is in Auto Mode This helps focus attention to the operation of the fixture You can also adjust the light levels of the LEDs by pressing the g button The levels will be adjusted in the following cycle 100 66 33 Off 20 PERIMETER MOTION TRACKING DETECTION Underneath Fixture The Light fixture has a separate motion detection sensor and dow
9. n firing LEDs located on the bottom When movement is detected underneath the fixture the down firing Perimeter LEDs will turn on and illuminate the area directly underneath the fixture They will remain on for 90 seconds unless motion continues to be detected In addition the main LED s on the front of the fixture will also turn on for 90 seconds Motion sensor Risk of electric shock Turn power off before servicing see instructions Ensure that no bare wires are exposed outside the electrical connections Risk of injury LED light output is strong enough to injure human eyes Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds Some metal parts in the fixture may have sharp edges To prevent cuts and scrapes wear gloves when handling the parts Account for small parts and destroy packing material as these may be hazardous to children Risk of fire Minimum 90 C supply conductors No serviceable parts Non replaceable LEDs 21 This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interfer ence and 2 this device must accept any interference received including interference that may cause undesired operation FCC Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to the equipment
10. ng base through the basket See Fig 2 Align the two mounting screw holes on the gasket to the two mounting screw holes on the mounting base and press the gasket flush to the mounting base See Fig 2 11 3 Locate black and white wires coming from LED light fixture Strip wires 3 8 9 5mm if not previously stripped Hold BLACK house wire and BLACK fixture wire together with ends even Align any frayed strands or conductors Push wires into wire nut and screw Clockwise until two twists are visible in the wires Repeat above procedure for both the WHITE house wire and the WHITE fixture wire White to White ig Black to Black Gasket Note The Motion Tracking Spot Light does not utilize a house ground wire because of the plastic material of the mounting base The house ground wire does not attached to the mounting base Position house ground wire inside junction box 4 Position mounting base and gasket over the junction box Ensure wires and wire nuts are positioned inside the junction box Align holes of mount ing base with holes in junction box Insert mounting screws as shown See Fig 4 Ensure that gasket is evenly positioned around mounting base Using a screwdriver screw mounting screws into junction box until mount ing base is snug do not over tighten 12 Note If a wet location junction box was not used caulk edge of mounting base with silicone weather resistant sealant not included
11. or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 10 E Memorial Road Oklahoma City OK 73114 ao is a trademark of General Electric Company and is used under license to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 www jascoproducts com 45262 rev 9 2 11
12. s present position inside junction box 4 If mounting to a wall in vertical position ensure the mounting base is correctly oriented with the collar screw positioned downward See Figure 4A Position mounting base and gasket over the junction box Ensure wires and wire nuts are positioned inside the junction box Align holes of mounting base with mounting holes in junction box Insert mounting screws as shown See Fig 4B Ensure that gasket is evenly positioned around mounting base Using screwdriver screw mounting screws into junction box until mounting base is snug do not over tighten Note If a wet location junction box was not used caulk edge of mounting base with silicone weather resistant sealant not included 5 Plug the wire connector from the base into the wire connector from the LED Motion Tracking fixture See Fig 5A Next insert adjustment knuckle into mounting base collar opening Position connectors and wire inside adjustment knuckle take care not to pinch the wire When properly inserted adjustment knuckle will snap into place Tighten collar screw of securing collar until snug See Fig 5B Do not over tighten 10 HORIZONTAL EAVE MOUNT AND WIRE CONNECTION 1 Remove the existing light fixture and disconnect house wires black white and ground if present See Fig 1 2 Route the black and white wires coming from the back of the mounti
13. tection area As the person moves within the detection area the heat measurements change Motion Sensors determine these changes to be movement All motion sensors are more sensitive to movement across the detection area and less sensitive to movement toward the sensor The Motion Sensor on the GE LED Motion Tracking Security Light is designed to detect motion up to 180 and outward from the fixture up to 40ft Less Sensitive More Sensitive TEST MODE TEST MODE 1 Once the fixture is mounted and positioned you can test the detection range for each adjustable sensor by placing the fixture into TEST Mode 1 Locate the infrared remote control Point the remote at the infrared window located in front of the fixture and press and release the TEST button once Note you 18 must be in front of the fixture witin a 15 angle and within 15 ft When the fixture receives the commana the lights will turn on and the light housing will automatically rotate to the far left and then to the far right It will then rest at the center position The red indicator light on the front will blink rapidly You may now walk around the fixture testing the motion detection angles When either or both sensors detect motion the lights will turn on for 3 seconds and then turn off This will allow you to ensure the sensors are to set to detect mo tion in the desired areas In this test mode the light housing will
14. the front and one perimeter motion sensor located on the bottom The dual adjustable sensors are used to detect and track motion in front of the LED light fixture The perimeter motion sensor on the bottom is used to detect motion underneath the LED light fixture Locate the adjustment thumb screw on the side of the adjustment knuckle Loosen the thumb screw slightly to allow adjustment of the light fixture angle Depending on the mounting height you may need to angle the light fixture at a slight downward angle so the motion sensors are able to detect motion near the light fixture The front adjustable motion sensors have a fixed detection range up to 45ft By adjusting the angle of the fixture you will adjust the motion detection range See Fig 8 Minimum Detection Average Detection Maximum Detection Distance Distance Distance MOTION DETECTION RANGE SET UP Each adjustable motion sensor can detect motion in front of the light fixture up to 100 The upper sensor is sensitive to motion on the left side of the light fixture the lower sensor is sensitive to motion on the right side of the light fixture The overlap area from the two sensors creates a Center detection area in front of the light fixture When the adjustable sensors are set to the Narrow position equal emphasis is given to the left right and center detection zones The center detection zone
Download Pdf Manuals
Related Search