Jasco 45254 Instruction Manual
Contents
1. Adjustment SQ Knob 1 Ensure power is turned on to the LED Light fixture 2 Loosen the adjustment knob and lock nut for the motion detection sensor and position it so points outward toward the approximate middle of the area to be detected 3 Angle the Motion sensor slightly downward ap proximately 10 15 This will create a maximum detection area with the most accuracy from 6ft to 60ft Best Option Too Far To Close Avoid pointing sensor too far downward as this will reduce detection cover age and overall distance If the sensor is pointed too high it may not detect movement closer to the fixture It may be necessary to make minor adjust ments until you have the sensor set to the optimum position 4 Position the sensor so any areas to the far left or far right are covered Distance outward from the sensor is fixed So no adjustments are necessary The detection pattern is similar to a half circle however it will detect farther ahead than on each side a i Important Note 1 Do not point motion sensor toward bright lights or reflective surfaces as this will affect accuracy of the motion sensor 2 Avoid areas with heavy traffic or pet areas as this may trigger lights consistently 3 Avoid pointing sensor directly towards severe temperature surfaces such as heating vents air conditioners driveway or asphalt surfaces large light colored objects that reflect heat or other light sources Thes2. one of the large openings of the gasket See Fig B 4 Locate black white and ground wires coming from LED light fixture Strip wires 3 8 9 5mm if not previously stripped Hold BLACK house wire and BLACK fixture wire together with ends even Align any frayed strands or con ductors Push wires into wire nut and screw ClockWise until two twists are visible in the wires Repeat above procedure for both the WHITE house wire and the WHITE fixture wire Repeat above procedure for both the GREEN or BARE COPPER house wire and the BARE COPPER fixture wire Gasket Mounting Plate Black to Black White to House ground wire to copper ground wire from fixture 5 Insert mounting bolt through center of cover housing as shown Align mounting bolt thru the small center hole of gasket to hold gasket in place Position cover housing and gasket over the junction box Align center bolt with center hole of mounting plate Using Phillios screwdriver screw mounting bolt into mounting plate until LED light fixture is snug do not over tighten 6 Cover mounting bolt by inserting GE badge into hole align badge with mounting slots Press in until snug 7 If a location junction box was not used caulk edge of cover housing surface with silicone weather resistant sealant not included ADJUSTING LIGHT HOUSINGS Adjustment 1 Slightly loosen adjustment knob and lock nut for one housing at a time Gently position
3. LED housing to final desired position Tighten adjustment knob and lock nut If necessary follow same adjusting for the other Light Housing 2 Turn on power at circuit breaker or fuse box Turn on light switch if pres ent Check LED light output to ensure proper coverage TEST MODE INITIAL SET UP Note After power is turned on the motion sensor requires approximately one minute to warm up before it will detect motion levels The LED light fixture is pre set to the TEST mode from the factory to help you position the mo Time Dark tion sensor so it can detect motion in the desired a area In TEST mode the LED lights will turn on for TRES approximately 5 seconds each time motion is de tected including during daylight After complet ing the test set up you can adjust the time the lights remain on from 1 to 10 minutes variable While in TEST mode the lights will turn on during daylight OPTIMIZED LIGHT OUTPUT Provides a variety of lighting applications Simply adjust the angle of the lights MOTION SENSOR POSITION SET UP Note The motion detection range has been set to a maximum sensitivity up to 60ft This is the optimum reliable distance At longer distances there is a greater tendency for false activations Maximum sensitivity distance will vary based on outside conditions temperature weather mounting location and detection angle
4. MOTION ACTIVATED LED Security Light User Manual www jascoproducts com 1 800 654 8483 Thank you for purchasing the GE LED Security Light with Motion Activation control This economical energy efficient LED light has been de signed to allow easy installation flexible mounting options and provide exceptional light output with minimum power consumption Please read all the Instructions carefully Keep them for future reference PARTS LIST Before installing please ensure all the following items are included in the package LED Security light with Mounting plate Gasket two light housings and screws and motion sensor OS 3 Wire Connectors Mounting Bolt GE Badge n m TOOLS NEEDED Phillips head screwdriver 2 aD W Questions Problems Missing Parts If you have any questions regarding the installation or operation of the product Before returning to Retailer please contact Technical Support at 1 800 654 8483 option 4 WARNING Turn power off at circuit breaker or fuse box Do Not rely on a wall switch alone to turn off power Consult a local licensed electrician or electrical contractor if you are not sure about the installation Always install wiring connections in accor dance with local code ordinances and National Electric Code WARNING The LED light output is strong enough to injure human eyes Do not stare directly at the LEDs for more than a few seconds INSTALLATION Select an ex
5. e heat sources can generate false activations and reduce motion sensor distance 5 Ensure the Time knob is set to TEST rotate counter clockwise to left The Dark knob is set to the minimum position rotate counter clockwise tec7 to left In this TEST mode the lights will turn on for 5 seconds after motion is detected and then turn off In the TEST mode the lights will turn on during daylight 6 To test motion activation coverage walk through detection area noting your position when the lights turn on To increase the coverage area raise the motion sensor up slightly To reduce the coverage area position the sensor downward slightly Once optimum coverage set tighten lock nut and adjustment knob until snug Do not over tighten 7 Once you have completed the test set up adjust the Time setting from Test position from 1 to 10 minutes as desired When out of TEST mode the LEDs lights will not turn on during daylight hours when motion is detected Time Dark xN 10 DUSK DAWN LIGHT LEVEL ACTIVATION SETTING The LED light fixture has an adjustable light level activation setting labeled Dark This adjustment allows you to determine when the LED lights will turn on based upon the darkness level outside In some situations depending upon on where the fixture is located you may wish to have the LED lights turn on sooner example the LED light fixture is positioned
6. in a shaded area Or you may wish to have the LED lights turn on when it is darker outside example the LED light fixture is located in an area that receives direct afternoon sunlight Dark 1 To set lights to turn on under darker conditions rotate DARK knob to the right clockwise to Max position 2 To set lights to turn on under lighter conditions turn rotate knob to the left counter clockwise to Min position 3 It may be necessary to make minor adjustments until satisfied with activation levels 11 LED LIGHT ON TIME SETTING The LED light fixture has an adjustable time setting that determines the length of time the LED lights will remain on after motion is detected You can adjust the light on time from 1 minute to 10 minutes Adjust the Time setting from Test position from 1 to10 minutes as desired Note In the TEST setting the lights will turn on for 5 seconds after motion is detected and then turn off and will turn on during daylight approx 1mm approx 10 mm HOW DOES MOTION DETECTION WORK Motion sensors are actually heat sensors Motion Sensors detect motion by monitoring changes in heat within the detection area As a person enters the detection area the sensor compares the outside temperature with the body temperature of the person within the detection area As the person moves within the detection area the heat measurements change Motion Sensors determine these cha
7. isting light fixture either wall or eave mount for replacement Note The fixture must be connected to 120v 60Hz power source MOUNTING PREPARATION FOR THE LED LIGHT FIXTURE Note For maximum flexibility the LED Security Light can be mounted on a wall vertical or under the eave horizontal Eave Mount Wall Mount Lock Nut Adjustment Knob Cover Housing Mounting Plate Dusk Dawn Time Adjustment Adjustment for Lights Locate the adjustment knob and lock nut on the LED fixture Loosen both and position LED light housings into the approximate position prior to mount ing For wall mount the LED light housings should be positioned above the motion sensor For under eave mount position cover housing horizontally so that LED light housings are facing outward away from the wall and motion sensor is positioned in front of LED light housings Fine tune adjustment can be completed after LED light fixture is mounted to junction box WIRE CONNECTION WARNING Turn power off at circuit breaker or fuse box Do Not rely on a wall switch alone to turn off power 1 Remove the existing light fixture and disconnect house wires black white and ground 2 Install mounting plate to junction box as shown using two mounting screws included Install screws until snug so that mounting plate does not move Do not over tighten screws See Fig A 3 Position gasket over junction box Route black white and ground house wires through
8. nges to be movement All motion sensors are more sensitive to movement across the detection area and less sensitive to movement toward the sensor The Motion Sensor on the GE LED Security Light is designed to detect motion up to 180 and outward from the fixture from 6ft up to 60ft Less Sensitive More Sensitive FCC Statement This device complies with Part 15 of the FCC rules Operation is subject to Bieler cloctneehock the following two conditions 1 this Turn power off before servicing see device may not cause harmful interfer instructions ence and 2 this device must accept Properly ground fixture f ved includi Ensure that no bare wires are exposed any Interference received Including outside the electrical connections interference that may cause undesired Risk of injury operation LED light output is strong enough to injure human eyes Precautions must be be taken to prevent looking directly FCC Note The manufacturer is not at the LEDs with unaided eyes for more responsible for any radio or TV E lt econde interference caused by unauthorized Some metal parts in the fixture may modifications to the equipment Such have sharp edges To prevent cuts and modifications could void the user s scrapes wear gloves when handling the parts Account for small parts and destroy packing material as these may be NOTE This equipment has been tested hazardous to children and found to comply wi
9. th the limits for Risk of fire i a Class B digital device pursuant to E tec a PONLO Part 15 of the FCC Rules These limits Non replaceable LEDs are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communica tions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help authority to operate the equipment GE is a trademark of General Electric Company and is used under license to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 www jascoproducts com 45254 rev 5 23 11
Download Pdf Manuals
Related Search