Jasco 45142 Instruction Manual
Contents
1. There is loss of signal from the Sensor to the Control Center such as low battery or Sensor is out of range The system is armed The Control Center will sound three beeps to indicate it could not erase the Zone Testing a Sensor or your system Once all the Sensors have been assigned to Zones in the Control Center you can now test your system This allows you to test a Motion Sensor in Zones 1 2 3 without arming the system Ensure the Control Center can receive the signal from the intended location of the Sensor before permanently mounting a Sensor Step 1 Unplug AC adapter and remove batteries Step 2 Press and hold the Mute button and plug the AC adapter back into the Control Center When all the LED indicators turn on release the Mute button The Control Center is now in Test Mode and any Sensor can now be tested in any Zone Step 3 Set the Notification Mode to Alert position see Notification Mode switch Page 6 and begin activating Sensors one at a time Note For the Motion Sensor stand in front of the Sensor and remain motionless for 20 seconds Begin moving and if the Sensor is within range of the Control Center it will activate the Zone in the Control Center for 15 seconds Step 4 When testing is complete unplug the AC adapter then plug the AC adapter back in and reinstall batteries This returns the Control Center to standard operation mode Note The Control Center will automatically return to st2. Select the Zone to bypass Before arming the system press and hold the Zone button for three seconds The Control Center will sound a long tone while the button is pressed After three seconds the tone will stop and the Zone LED indicator will turn on The Zone has been set to bypass Note Sensors in a bypassed Zone will not trigger the Alarm Alert or Chime functions Step 2 Arm system HOME or AWAY Step 3 The Bypass setting can be removed by pressing and holding the Zone button again for three seconds or by disarming the system ACCESSORIES Silent Alert Alarm Siren and Signal Repeater Silent Alert The Silent Alert is designed to provide a visual warning BEFORE entering the home if an alarm has been triggered You can add any number of Silent Alert 5 LED indicators to the Choice Alert System o To add a Silent Alert to the system you will need to link it with the Control Center Adding a Silent Alert Step 1 Open the Silent Alert by gently inserting a small blade screwdriver into the tab slot on one end and gently pry upwards This action releases the cover from the base This procedure can be easily completed once the Silent Alert is mounted as well Install two 2 new AA batteries according to the polarity markings in the battery compartment Step 2 Press and hold the Learn button inside the Silent Alert One of the LED indicators on the front of the Silent Alert will begin to flash Step 3 W
3. the user s manuals There are no user serviceable parts 2 Handle with Care Avoid striking or shaking Improper use or storage could damage the Control Center Modifying or tampering with the device or its internal components can cause a malfunction and void the Control Center s warranty 3 If you feel the Control Center or any part of the Choice Alert system is not operating correctly or as described please contact Customer Service for assistance 1 800 654 8483 Before you begin to install your Choice Alert System you will need to plan your security needs Consider all the doors and windows that are likely to be used as points of entry by an intruder such as those poorly lit or an entrance or window that cannot be easily seen from the street You may want to know if the back gate is open whether the garage door is still up or if the storage shed in the backyard is secure Perhaps you re concerned about the hot water tank or the dishwasher leaking This system will help alleviate those concerns To start sketch a map of areas in and around your home and determine which doors and or windows need contact Sensors which areas that might best be served by a Motion Sensor etc The Choice Alert system can manage up to 16 Sensors a maximum of any four 4 Sensors in any of the four 4 protection Zones See diagram of the example sketch We recommend installing a Window Door Sensor on the door that you enter exit most
4. each of the 4 Zones in the Choice Alert system Armed and Power Indicators These LEDs indicate status of the system Keypad Operations Arm button Use this button on the keypad to select the arm setting HOME or AWAY you wish to use Input DC 12 V AC adapter input jack Mute Button Used to mute a triggered Zone See pg 7 Armed Power Indicators Learn Button Used to link Sensors and Accessories to the main unit See pg 10 Features Battery Back up Control Center The Control Center offers battery backup up to 48 hours in case of power failure While the system will operate correctly without batteries it is highly recommended to install four 4 new AAA Alkaline batteries To install batteries unplug the AC adapter from the Control Center and rotate the unit bottom side up revealing the battery compartment on the base 5 Slide the battery compartment cover off in the direction of the arrow Install batteries according to the battery polarity diagram inside the battery compartment Replace the battery door Note The Control Center has an automatic internal battery tester After batteries are installed you can check the backup battery status at any time by unplugging the AC adapter If the batteries are acceptable the green Power LED indicator will be remain on If the batteries are low the LED indicator will flash slowly If the batteries are too low to power unit or dead the LED indic
5. indicate where Sensors are located around your home On the reverse side of the card are brief instructions for Arming Disarming the system and assigning a Sensor to a Zone Lets get started Use the following tips to select an ideal location Position it in a central location of the home within a few feet of an electrical outlet some place accessible and easily noticed Away from doors and windows where it could be easily noticed by intruders Away from heat sources such as an oven stove or vents Away from large metal objects such as refrigerators microwaves etc which could effect the wireless performance After you have selected a location for the Control Center you are ready to set up your system 1 Plug in the AC adapter to a nearby electrical outlet and plug the other end into the Input DC12V jack on the side of the unit All the LED indicators on the front of the unit will light up briefly and go out This indicates the Control Center has completed a brief system check Only the green power LED indicator should remain on 2 Place the Control Center in the selected location and rotate the antenna to the upright position for best reception The Control Center should be able to receive signals from Sensors and Accessories up to 150 feet away Creating a Personal Security Code The Security Code is used to arm and disarm the alarm system The Control Center comes with a factory def
6. keep waiting on the beep But nothing happens Why A There is a short beep that you hear as soon as you press the Learn button After you hold the Learn button for about 3 seconds you will hear a long beep once the long beep sounds you have 15 seconds complete the other steps in the process Q bought a new Sensor and the Control Center will not recognize it Why A First make sure that the batteries are new and that the battery is inserted into the Sensor according to polarityl markings Second make sure that you have assigned the Sensor to a Zone If the Sensor LED is flashing rapidly all the time remove and reinsert the battery Q put Sensors on Zone 4 and it will not set off the alarm Why A Zone 4 is a Dedicated Alert Zone and is designed to monitor Sensors in this Zone It will only issue an alert LED will flash continuous beeping will be heard Sensors in Zone 4 will not set off the alarm Use Zone 4 for water Sensors garage doors gates sheds or other areas that you want to monitor i e areas that you want to be alerted if there is a problem but do not want the alarm to sound Q have trim on my door and cannot match my Sensor to the magnet Will this work on my door A The Sensor can be up to apart from the magnet 16 Q erased a Sensor from a Zone and now all of my other Sensors in that Zone will not work Why A The system can only erase entire Zones You will need to ad
7. 45129 Wireless Alarm System Control Center User s Manual SsGholce ALERT Perio all Sens amp access6ries fro Onelocation Important Safeguards Designing a system Controls Indicators and Features Battery Backup Control Center The Choice Alert Operating Modes otification Mode Dedicated Alert Mode Zone 4 Armed Alarm Modes Mute Function Placement of the Control Center Creating a Personal Security Code Sensors and Zones Assigning a Sensor to a Zone Erasing a Sensor from a Zone Low Battery Indicators Control Center amp Sensors YO CO O NNN DDD HH LFW e e e O Table of Contents Testing a Sensor setting the Control Center into Test Mode Arming the System HOME or AWAY Disarming the System Bypassing a Zone Accessories Silent Alert Alarm Siren Signal repeater Q amp A Important Information FCC Warning Limitations of Alarm products Product Warnings 12 13 14 14 15 16 17 18 20 20 Before connecting or operating the Control Center please read these instructions carefully and save this manual for future reference Congratulations The GE Choice Alert Wireless Alarm System is one of the most affordable and expandable wireless alarm systems available You ll discover that the system offers many features typically found in custom installed Alarm systems The Choice Alert system is reliable and easy to
8. allation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 18 Model 45 45 45 45 45 45 45 45 29 30 31 32 35 36 37 38 Description Control Center Garage Sensor Door Window Sensor Motion Sensor Water Leak Sensor Alarm Siren Silent Alert Signal Repeater Battery Type 4 AAA 1 2032 2032 Iov 2032 9V 2 AA o batteries Battery Life 24 months 24 months 24 months 9 months 24 months 24 months 18 months N A maximum potential life based upon usage and location 19 WARNING Limitations of Alarm Products This product should be tested periodically to make sur
9. andard 11 Operation mode after 5 hours Arm HOME No delay instant alarm This setting is used when you wish to secure the area but will be home and moving around within the armed area In the Arm HOME setting any Motion Sensors in Zone 1 2 and 3 will not operate All Sensors must be closed not activated in order to set the alarm To set the system in HOME mode HOME Mode L J To set the Alarm in Home Mode B step 1 ie i Enter four digit Security Code Step 2 s Press and HOLD Arm x button for two seconds Note Motion Sensors do not operate in HOME Mode The Armed LED indicator turns on C1 2 3 a am 3 4 Armed Power l Step 3 ee 2 Zre To disarm enter the four I digit Security Code Only Zones 1 2 and 3 Step 1 Enter your four digit Security Code Step 2 Press hold the Arm button for two seconds The red Arm LED indicator will turn on The system is now Armed Arm AWAY Delayed alarm for entry exit After the system is armed a 45 second delay begins This is to allow time to leave the protected area before system is active The Control Center will begin beeping and the Armed LED indicator will begin to flash During the last 10 seconds the beeping will speed up indicating the alarm will arm shortly Once the alarm has become active the red LED indicator will continue to flash until system is disarmed In the Arm AWAY setting al
10. ator will be off Low Battery Indicator Sensors The Control Center continuously monitors all the Sensors If the Control Center does not receive a signal from any Sensor it will begin rapidly flashing the Zone LED indicator This indicates one or more Sensors in the Zone may have low battery power and are unable to transmit a signal the necessary distance If all batteries and or Sensors are installed at the same time into a Zone it is recommended to replace the batteries in all Sensors in the Zone However you can check the Sensor s status independently by placing the Control Center in Test mode see Testing a Sensor on page 11 and trigger each Sensor separately i e open door If the Sensor does not trigger an alert then replace the batteries Note The Sensor detection system is range dependant which means Sensors located closer to the Control Center may seem to have batteries that last longer than those Sensors at a greater distance Also keep in mind because the Motion Sensor is continually checking for activity the battery life is less than the lithium cell batteries in the other Sensors An Alkaline 9V battery in the Motion Sensor can last up to 9 months the 6 Lithium cell batteries in the Door Window Garage and Water Leak Sensor can last up to two years If the Motion Sensor is ina Zone with other Sensors try replacing its battery first INTRODUCTION Let s review the different features function
11. ault Security Code setting of 1 23 4 It is recommended to establish your own Personal Security Code To change the Security Code locate the Learn button on the side and Arm button on top E m Step 2 n a Enter the current code ae Step 3 Ma 5 Enter new code Step 4 NS wf Re Enter new Input DC 12v stani 7 7 code to confirm oe tep Press and hold a the Learn button man Then press and A 1 2 3 A aml hold the Arm Al L nat button together a g d re Poker for three seconds Zone e e C Ld e C Note When setting the Security Code you have 15 seconds to begin making the change After 15 seconds the unit will time out and return to stand by mode If this happens you will need to start over Step 1 A Press and hold the Learn button unit will beep B While continuing to press the Learn button press and hold Arm button within three seconds C When Control Center sounds a long beep release buttons The green LED power indicator will begin flashingThis indicates the unit is ready to change the Security Code Step 2 While the LED indicator is flashing enter the current Security Code if new then enter the factory Security Code of 1 2 3 4 Step 3 Enter your new four digit Code Step 4 A Enter your new four digit Code again to confirm B Along beep will sound and the green LED indicator will stop flashing Your new Co
12. d the other Sensors back in that Zone to the Control Center again Q Why does one of my Zones continually flash A This can be caused by 1 of 2 conditions First condition if it is a rapid flash it means a Sensor in the Zone has a low battery If more than one Sensor is in a Zone you will need to test each Sensor by putting the unit into test mode see pg 11 of manual It may also be that a Sensor is out of range and cannot make contact with the Control Center If this is the case you may need to move the Control Center closer or use a Range Repeater The Second condition if it is a slow flash one of the Sensors is triggered Check all Sensors to ensure the Sensors in the Zone are reset i e close door window etc Q If one Sensor has a low battery should replace all of the batteries A If Sensors were added at the same time chances power are good all the batteries will need to be replaced Q How do know if any Sensors have low batteries A The Control Center will indicate if any Sensor does not have sufficient power to transmit a status signal battery is low You can also check each Sensor independently by using the Test Mode see pg 11 in manual Q If one Sensor has a low battery will the other Sensors in the Zone or other Zones continue to operate A Yes as long as the other Sensors have sufficient battery power they will continue to transmit information to the Control Center and the system wil
13. de has been set Note If the Security Code is lost or forgotten you can restore the Control Center back to factory default Security Code setting 1 2 3 4 Remove the batteries and AC adapter Press and hold the Learn button and plug the AC adapter back in continue pressing the Learn button Wait until all 4 Zone LED indicators are on and the Zone 1 LED indicator begins to flash The Control Center will need four hours to reset the Security Code back to the factory Default 1 2 3 4 Once all Zone LED indicators turn off the system will be reset to the factory default The alarm system cannot be used during this four hour reset process Sensors and Zones There are four Zones and each Zone can hold up to four Sensors Any combination of Sensors Motion Door Water or Garage can be assigned to any of the four Zones If you decide to expand it is important to know you can always add more Sensors 16 total Zones 1 2 and 3 are designated for Arm Alarm or Notification modes 8 Na Ay MO Control Center has gt AR three Mode settings Mut Alert Continuous Tone team Chime Single Tone a ae Off Lights only 1 2 3 4 am Xl a peal _ Notification switch 4 A O 4 e on affects Zone 1 2 3 only Zre e e XX Zone 4 is designated for detected Alerts only Use Zone 4 for areas you wish to continuously monitor but
14. designed for continuous monitoring It works independently of the Notification Mode switch and the Alarm System Sensors in Zone 4 will not trigger an alarm HOME or AWAY Sensors in Zone 4 do not respond to the Off Chime Alert Notification Mode switch Mode 3 Armed Alarm Mode Zones 1 2 3 Arm HOME Instant alarm In this setting the alarm is instant no delay when a Sensor is triggered All Sensors except Motion Sensors in Zones 1 2 and 3 will trigger the alarm Sensors in Zone 4 will not trigger the alarm Zone 4 is for Alerts only Arm AWAY Delayed alarm In this setting there is a 45 second exit delay before system is armed This allows time to leave the protected area There is also a 30 second entry delay this allows time to enter the protected area and disarm the system before alarm sounds All Sensors in Zones 1 2 and 3 will trigger the alarm Sensors in Zone 4 will not trigger the alarm Zone 4 is for Alerts only Disarm Entering the 4 digit Security Code anytime the system is armed will immediately disarm the system regardless of HOME or AWAY setting Bypass You can bypass a Zone so that any Sensors in that Zone 1 2 and or 3 will not trigger the alarm regardless of HOME or AWAY setting Quick Reference Card The Control Center comes with a quick reference card and clear storage envelope Attach the clear envelope using the peel off adhesive and press it to the bottom of the Control Center Use a pencil to
15. don t want to trigger the alarm e g notification of water leaks garage door is up back gate left L CIN Continuosly Monitors any area in and around the home using any combination of the four Sensors Note Zone 4 is not affected by Notification mode switch and does not activate alarm Deticated Alert Zone Zone 4 open storage sheds or work shops unsecured etc Sensors placed in Zone 4 will not activate the Alarm or Chime When a Sensor is triggered in Zone 4 the Control Center will sound a repeating Alert 4 beeps and the Zone 4 LED indicator will flash continuously These Alerts will continue until the Sensor is closed You can Mute the repeating Alert sound but the LED indicator will continue to flash until the Sensor is reset deactivated i e door is closed Here are Some examples of possible Sensor Zone combinations Example 1 4 Sensor system Zone 1 Door Sensor front door Zone 2 Motion Sensor living room Zone 3 Window Sensor bedroom Zone 4 Water Leak Sensor hot water tank Example 2 6 Sensor system Zone 1 Two Door Sensors front door amp patio door Zone 2 Two Window Sensors kitchen amp bedroom Zone 3 Motion Sensor living room Zone 4 Water Leak Sensor washing machine Example 3 10 Sensor system Zone 1 Two Door Sensors front door amp back door Zone 2 Four Window Sensors bedroom o
16. e it is working properly The product if used properly may reduce the risk of burglary robbery or other adverse events However JASCO is not an insurer this product is neither insurance nor a guarantee that such an event will be prevented and users should protect themselves with proper insurance JASCO makes no representation that this product cannot be compromised or circumvented that it will provide an adequate warning or that it will prevent any personal injuries property damage or other losses Like any alarm product including expensive commercial systems it may be bypassed it is subject to compromise and it may fail to warn for a variety of reasons including but not limited to improper installation or positioning improper maintenance tampering dead or improperly installed batteries sensing limitations component ailures receivers intrusions may be outside of a product s designed range and certain environmental conditions may impact performance and audible alarm signals may be outside of hearing range muted by doors walls and floors unheard by deep sleepers or the hearing impaired or overwhelmed by other sounds is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC 10 E Memorial Road Oklahoma City OK 73114 This Jasco product comes with a 1 year limited warranty Visit www jascoproducts com for details WARNING Risk of personal injury e Prolong
17. ed exposure to alarm siren may cause permanent hearing loss Battery Warning e Remove batteries before storing the Alarm for extended periods e Batteries may leak harmful liquids or ignitable materials or explode causing injury and product damage e Do not mix old and new or other battery types e Replace all batteries at the same time e Replace fully discharged batteries immediately 45129 1 11 02 07
18. hile continuing to press the Learn button in the Silent Alert press and hold the Mute button on the side of the Control Center for three seconds The Control Center will sound two beeps and flash the green power indicator a test signal to the Silent Alert When the Silent Alert receives the test Signal the LED indicator will stop flashing indicating it has been linked with your Control Center Reattach the Silent Alert to the base Anytime the alarm is triggered in Armed HOME or AWAY the siren sounds and the Control Center will send a signal to the Silent Alert to begin alternately flashing its LED indicators The Silent Alert will continue to flash the LED indicators until the Control Center sends a disarm signal Note Even if the Control Center is disconnected from power or destroyed the Silent Alert will continue to flash LED indicators Test the Silent Alert Step 1 After the Silent Alert has been successfully linked with the Control Center press and hold the Mute button on the Control Center for three seconds This action sends a test signal Step 2 When the Silent Alert receives the test signal from the Control Center one LED indicator on the Silent Alert will begin to flash once a second It will continue to flash for 30 seconds Alarm Siren The Alarm Siren will increase your system s sound Use in areas where Control Center Siren cannot be heard Adding a Alarm Siren Step 1 Remove cover vob La a o
19. l operate normally Q programmed all my Sensors to a Zone but only 4 work Why A This system is designed to hold 4 Sensors per Zone If you add more than 4 then the first Sensor added will be deleted to make room for the new Sensor If you have more than 4 Sensors you will need to use multiple Zones Q switched the Control Center to off but the lights are still on Why A More than likely you are changing the position of the Zone Notification switch to the off position When you set this switch to off position this turns the chime and alert notification sounds off It does not turn the Control Center off The Control Center does not have an off switch to disable the Control Center you will need to unplug the adaptor and remove the batteries Q When I arm the system my motion Sensor doesn t trigger the alarm Why A The motion Sensor is designed to work in the AWAY mode but not the HOME mode This allows you to have the system armed and still be able to move about the house 17 Q The manual states there is a 48 hour back up Do have to reprogram the Zones if it has been without power longer than 48 hours A No The Control Center will store the Zone and Security Code Settings indefinitely Q One of my Sensors was damaged and the Control Center keeps flashing how to I stop this A First unplug the adaptor and remove the batteries for 5 seconds Then replace the batteries and plug in the ada
20. l Sensors in Zones 1 2 and 3 will trigger the Alarm System All Sensors must be closed not activated in order to set alarm To set system in AWAY mode Step 1 Enter your four digit Security Code Step 2 Press the Arm button two times The red alarm LED indicator will flash continuously AWAY Mode E p To set the Alarm in Away Mode CON ta Eo digit Security Code NS 2 A Baer button twice The Armed LED indicator t _ begins flashing 45 seconds to exit Step3 To disarm enter the four digit Security Code 30 seconds to enter e 1 2 c EERE zr e Only Zones 1 2 and3 Note If a Sensor is triggered in Zone 4 it will not activate the alarm It will sound an alert tone only See Zone 4 page 9 Disarming the System When you return to the protected area the unit will trigger and give you 30 seconds to disarm the system To disarm the system at any time enter the four digit Security Code Entering the four digit Security Code will disarm the system during the 30 second delay entry period or even if the alarm has been triggered and the siren is sounding Bypass a Zone For all Zones and Modes There may be occasions when you would like to temporarily prevent the Sensors in a Zone from triggering the alarm In this situation you can bypass a Zone when setting the alarm Once the alarm is disarmed the Bypass setting will be removed Step 1
21. n top of the Alarm Siren Plug in the AC adapter Insert the O O antenna and slide mode switch to the ON position Step 2 Press and hold the Learn button inside the Alarm Siren The ON indicator on the front will begin to flash and it will sound three beeps Step 3 While continuing to press the Learn button press and hold the Mute button on the side of the Control Center for three seconds The Control Center will send a test signal to the Alarm Siren When the Alarm Siren receives the test signal it will sound a long tone and the ON indicator will stop 14 flashing This indicates the Alarm Siren has been linked with the Control Center Replace cover to Alarm Siren Test the Alarm Siren Step 1 After the Alarm Siren has been successfully linked with the Control Center press and hold the Mute button on the Control Center for three seconds Step 2 When the Alarm Siren receives the test signal from the Control Center one LED indicator on the Alarm Siren will begin to flash It will continue to flash for 30 seconds This indicates it has received the test signal The Signal Repeater will extend the range of the Choice Alert system up to 150 feet from its location Effectively repeating the signal from any Sensor back to the Control Center should a Sensor be located out of range The Signal Repeater does not send or receive signals to the Silent Alert or Alarm Siren Adding a Signal Repeate
22. nd In this mode when a Sensor is activated the Control Center will issue a continuous Alert beeping sound and a visual Alert flashing Zone LED indicator Both the flashing LED indicator and the beep sound will continue until Sensor is deactivated door or window is closed etc The number of beeps will be determined by which Zone has an activated Sensor Zone 1 you will hear 1 beep 1 beep 1 beep etc Zone 2 you will hear 2 beeps 2 beeps 2 beeps etc If a Sensor in more than one Zone is triggered i e Zone 1 and Zone 2 then you will hear 1 beep 2 beeps 1 beep 2 beeps etc Note A Motion Sensor in Zones 1 2 and 3 will not respond in the Alert mode It only functions as an Alarm Sensor A Motion Sensor can be used for an Alert in Zone 4 only Mute Use this button while in Alert mode to temporarily stop the continuous beeping Alert e g a window open or leaving the garage door up To activate mute for a certain Zone press the Mute button after the beeping starts All triggered Sensors in the Zone will be muted and the LED indicator will continue to flash until the Sensor has been reset To deactivate the mute reset the Sensor close door or window lower garage door remove water etc for that Zone If more than one Zone has a triggered Sensor pressing the Mute button will mute all triggered Zones Mode 2 Dedicated Alert Mode Zone 4 is a dedicated Zone for alerts only it is
23. ne two amp three Zone 3 Two Motion Sensors computer room and living room Zone 4 Door Sensor back yard gate Water Leak Sensor hot water tank Garage door Sensor 10 Assigning a Sensor to a Zone Assigning a Sensor into a Zone is an easy step process however there are a few points to remember Only one Sensor can be assigned at a time A Sensor cannot be assigned to two different Zones Up to four Sensors can be added per Zone if a fifth Sensor is added then the first Sensor will be replaced Batteries must be active in the Sensor before it can be assigned to a Zone Sensors can be assigned to a Zone and then mounted or can be mounted and then assign to a Zone The Door Sensor Garage Sensor and Water Leak Sensor use Lithium batteries To activate the batteries remove the yellow battery activation strip For the Motion Sensor attach the 9V battery leads to the battery Follow these steps to assign a Sensor to a Zone Step 1 Press and hold the Learn button on the Control Center for three seconds The Control Center beeps once Release the Learn button L ie 8 Step 1 na J Press and hold J the Learn button ag Jj for three seconds Step2 pades Select the Zone number u Step 3 litan Activate the Sensor poe amp team 1 2 3 4 am Z At S Q lt 1 2 38 4 Armed Power j on Zone Step 2 Press the Zone button 1 2 3
24. often and another at your secondary exit A Motion Sensor can be positioned in the area that has traffic such as stairs or hallways It can also be placed in main rooms living rooms dens computer rooms Additional Sensors can be added for exterior areas like garage door outside gate storage sheds and workshops You can also use the Water Leak Sensor to provide an Alert for potential water damage areas such as around a hot water tank washing machine dishwasher or air conditioner condensation pan Supplies needed Clean sheet of paper ruler and pencil with an eraser Note Motion Sensors can also be used to protect specific items that might be targeted by intruders i e electronic equipment TV s stereos and or computers Point the Motion Sensor directly at the equipment from an opposing wall or corner and if they are disturbed the alarm will be triggered Indoor Window Door Sensor 6 Water Leak Detectors 2 Motion Sensor i Garage Water Leak Sensor Garage Door Sensor Outside Motion Sensor I Window Door Sensor Antenna ek Side wW Alarm Siren Input DC 12V Input DC 12V O eB Mute Mute Keypad Xp team Learn C1 2 3 4 arm to at Chime Chime ouneanon off Switch 2 3 4 Armed Power 5 o 1 Zone Indicators Control Indicators and Features Zone Indicators These LEDs indicate Sensor status for
25. or 4 for the Zone you want to assign to the Sensor The LED indicator for that Zone will begin to flash Step 3 Release the Zone button Note Zone 4 is for dedicated alerts only Sensors in this Zone will not trigger an alarm or chime Step 4 Activate the Sensor For the Window Door Sensor separate the two pieces or if mounted open the door or window For the Garage Sensor lower the detection rod to its full extension if mounted raise the garage door For the Water Leak Sensor place the contacts in a small bowl of water or use a metal paperclip and ouch both contacts For the Motion Sensor press the Learn button ocated inside the battery compartment or if mounted wave your hand in front of the Sensor red LED indicator will flash inside lens area in front of Motion Sensor Erasing a Sensor from a Zone Note If you need to remove a Sensor from a Zone the system will erase the entire Zone so any other Sensors will need to be put back into that particular Zone Step 1 To erase a Zone press and hold the Learn button on the Control Center The unit will beep once Step 2 While holding the Learn button press and hold the Zone button to be erased After five seconds the Control Center will sound two beeps and the Zone LED indicator will flash twice Step 3 Release all buttons Note The Zone Sensor cannot be erased if The Zone has been triggered for an Alert or alarm The Sensor Zone must be reset
26. ptor Next You will need to clear the Zone see pg 11 and re assign all of the Sensors to the Zone including the replacement Sensor Q have my garage door Sensor in Zone 4 If want to leave the door open how do stop the continuous beeping A Press the Mute button on the Control Center This will temporarily mute the beeping sound for all Sensors in Zone 4 The Zone 4 LED will continue to flash until the door is closed Sensor is reset Once the Sensor is reset beeping will start again when Sensor door is opened Q The Silent Alert is flashing how do make it stop A On the Control Center arm the system in HOME mode and then disarm the system This will send a reset signal to the Silent Alert which will stop the flashing FCC Warning Any unauthorized changes or modifications to the equipment would void the user s warranty and may conflict with both state and federal laws The Choice Alert system complies with part 15 of the FCC rules Operation is subject to the following conditions 1 The Choice Alert system may not cause harmful interference 2 The Choice Alert system may accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential inst
27. r Step 1 Find an electric outlet near the Sensor having trouble communicating with the Control Center Make certain the location is between the Sensor and Control Center Plug the Signal Repeater into the outlet and press the Test button on the side of Signal Repeater It will send a test signal out to the Control Center and the LED indicator on the Signal Repeater will flash rapidly for about one second then go out Step 2 When the Control Center receives the Signal Repeater s test signal it will flash the green power indicator This means a confirmation signal was sent back to the Signal Repeater Release all buttons Step 3 When the Signal Repeater receives the confirmation signal the LED indicator will flash five times If the Signal Repeater does not receive the confirmation signal from the Control Center the LED indicator on the Signal Repeater will not flash You will need to move the Signal Repeater closer to the Control Center and retest Step 4 To Ensure the Signal Repeater can receive the signal from the Sensor activate the Sensor The Signal Repeater s LED indicator should flash rapidly and the Control Center should respond to the Sensor s signal This process will help you locate the Signal Repeater to the best farthest position from the Control Center in order to extend the range of the Sensor 15 Choice Alert Control Center F A Q S Q I am trying to program my security code and
28. s and terminology of the Control Center The Choice Alert System operates in three different modes 1 Notification Mode Zones 1 2 3 2 Dedicated Alert Mode Zone 4 3 Armed Alarm Mode Zones 1 2 3 Mode 1 Notification Mode Off Chime Alert Zones 1 2 3 Perfect for Windows Doors amp Motion Sensors alarmed areas Unarmed immediate notification mode User is notified of triggered Sensor based on position of notification switch Mode settings B gt gt Th B CON Control Center has three Mode settings cD Alert Continuous Tone Chime Single Tone off Lights only ani Notification switch or affects Zone 1 2 3 only 1 2 3 4 arm 4 Armed Power e e o a 1 2 3 zone Notification switch settings Off In this mode when a Sensor is activated the Control Center will issue a visual Alert only flashing Zone LED indicator no audio will be heard The LED indicator will continue to flash as long as the Sensor is activated door or window is open garage door is up etc Chime In this mode when a Sensor is activated the Control Center will issue a two tone chime sound In addition a visual Alert flashing Zone LED indicator will continue as long as the Sensor is activated open Note A Motion Sensor in Zones 1 2 or 3 will not respond in the Chime mode It only functions as an Alarm Sensor Alert Beeping sou
29. use With Choice Alert you can select from a line of Sensors and Accessories start small and expand as you need or create a system that meets all your needs The Choice Alert System is protected by Priority Code Selection technology which provides increased security and trouble free wireless connections It also guarantees the Control Center will only respond to signals from your Sensors in and around your home and prevents anyone from tampering with your system The user manual explains in simple steps how to install use and care for your new Choice Alert Control Center If you have any questions or would like additional information please visit our web site www jascoproducts com or contact our Customer Service Group at 1 800 654 8483 Important safeguards 1 Cleaning Unplug adapter and remove batteries before cleaning Do not use strong or abrasive cleaners Use a dry cloth to clean the surface of the Control Center In case the dirt is hard to remove use a damp not wet cloth for cleaning 2 Water and Moisture Do not use any component of this system in an exposed outdoor area except those specifically designed for that purpose such as the Door Window Sensor Motion Sensor Silent Alert LED indicator Water Leak Sensor Do not operate this system in the presence of explosive or flammable fumes Precautions 1 Do not attempt to disassemble the Control Center or any of the Sensors or Accessories unless described in
Download Pdf Manuals
Related Search