Jasco 19200 User's Manual
Contents
1. GE Model 19200 www jascoproducts com Wireless Portable Chime Installation Instructions for Wireless Portable Door Chime Kit Required Tools Small flat blade screwdriver drill drill bit and phillips screwdriver Included Hardware 2 3x20mm screws 2 Double sided adhesive pads The portable wireless door chime Kit has two components Portable Chime receiver Push Button Transmitter How To Install The Batteries 1 On the bottom of the portable chime you will find a round battery release tab Push the tab inward and slide the cover in the direction of the arrow The battery cover will slide off Battery Release Tab pes E SS o _ 2 Install 4 C cell batteries we recommend Alkaline Batteries 3 Remove back of wireless push button and install the 12 volt battery included as shown below a Chime Tune Setting All wireless chimes may have more than one push button The chime tune for each push button is set with jumpers 7 9 Single Push Button Kit If you purchased a kit with a single push button the chime tune will be set to Ding Dong from the factory Dual Push Button Kit If you purchased a kit with two push buttons one push button will be set to Ding Dong and the other push button will be set to Westminster from the factory The following instructions explain how to change the tune on any wireless push button 1 Remove the battery from the push button transmitter 2 Loc2. ate the 9 position jumper shown below i 9 position jumper This pushbutton is set for Ding Dong Chime since 7 off 8 on and 9 off 3 Select the desired chime sound from the table below Chime Sound Table Position 7 8 9 Westminster ON OFF OFF Ding Dong OFF ON OFF Knock OFF OFF ON Bronze Chime ON ON OFF Cuckoo Clock ON OFF ON Foghorn OFF ON ON Gong ON ON ON ON Adda jumper to a location OFF Remove jumper from a location 4 Remove or add the jumpers to match the table 5 Store unused jumpers as shown parked position Setting The House Security Code Setting The House Security Code is pre set at the factory and no further adjustment is normally required However if you experience erratic or no operation from your chime you may want to reset the House Security Code Setting Each component has jumpers for setting the house security code The chime and pushbutton must be set to the same house security code for the combination to operate together Note The push button has 3 additional jumpers that are used to set the chime tune that will play The chime tune jumpers do not affect the house security code 1 Remove power or batteries from the chime 2 To remove the batteries from the pushbutton open the pushbutton case as shown below a 3 Locate the House Security Code door and screw located on the back of the AC Chime Remove the screw and take off the door 4 Locate the chime and pu
3. not work see TROUBLESHOOTING Operation 1 Slide power switch to High or Low to power the chime 2 Gently press transmitter button to sound chime Troubleshooting Chime doesn t work Make sure push button switch is depressed and held for at least 1 second Make sure plastic tag is removed from battery Make sure house code switches 1 6 on chime and push button match exactly Verify battery orientation in push button Try fresh batteries Make sure chime is not farther than 150 feet away from push button Ensure push button is not mounted on metal near metal studs or near the floor 8 Try anew location for the chime Se Ole el Functional range may be adversely affected by one or more of the following factors weather radio frequency interference low transmitter battery and obstructions between the transmitter and receiver This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept interference received including any interference that may cause undesired operation For technical support contact Jasco Products Company at 1 800 654 8483 or www jascoproducts com Made in China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC 311 N W 122nd Street Oklahoma City OK 73114 www jascoproducts com Rev 1 07 19200
4. shbutton jumpers shown below Lhe pi i Push Button Jumpers Chime Jumpers in battery compartment 5 Jumpers 1 6 are used to select 1 of 64 possible home security codes 6 To change the house code add or remove jumpers as needed It is recommended to change only one jumper at a time and then test the system for proper operation Positions 1 6 on the chime and pushbutton must match exactly T Push Button Mounting Instructions Note Avoid mounting the push button on metal surfaces as it may result in a reduced range of transmission Do not mount in an area of rain direct weather a Removing the back cover b Replacing the back cover 1 Push buttons are typically mounted at the same height as the door knob or handle between 36 and 44 above the floor 2 Before mounting choose a mounting location that is not farther than 150 feet from the chime unit location Not farther than 150 feet 3 Place the push button where you would like to mount it and with the chime as close to its final position as possible and test operation If it works mount the button If it does not work see TROUBLESHOOTING 4 Use back cover of push button as a template to mark two screw holes 5 Drill two holes with 3 32 size drill in marked locations 6 Secure back cover to the mounting surface with two supplied mounting screws 7 Press front housing onto back cover 8 Test operation If the chime does
Download Pdf Manuals
Related Search