Home

Intel PPC-7508F User's Manual

1. Page 3 2 PPC 7508F USER S MANUAL Chapter 3 Software Configuration 3 2 VGA DRIVER UTILITY The VGA interface embedded with our PPC 7508F can support a wide range of display You can display CRT LVDS simultaneously with the same mode 1 Win 98SE program 2 Win 2000 program 3 Win XP program 4 NT4 0 program 9 Linux program 3 3 1 Installation of VGA Driver To install the VGA Driver simply follow the following steps 1 Place insert the Utility Disk into Floppy Disk Drive A B or CD ROM drive 2 Under Windows 98SE NT4 0 2000 XP system go to the directory where VGA driver is located 3 Click Setup exe file for VGA driver installation 4 Follow the instructions on the screen to complete the installation 5 Once installation is completed shut down the system and restart in order for the changes to take effect LA Under the Windows 98 system after rebut computer there will have two error messages appear Can t find ikch8xx cat and isb8xx cat just skip the messages they will not cause any effects PPC 7508F USER S MANUAL Page 3 3 Chapter 3 Software Configuration 3 3 FLASH BIOS UPDATE 3 3 1 Introduction Users of PPC 7508F can use the program Awdflash exe contained in the Utility Disk for system BIOS update 3 3 2 Installation of system BIOS 1 Copy Awdflash exe from Driver Disk to Drive C 2 Type the path to Awdflash exe and execute the system BIOS AWDFLASH 7500xx
2. r as F PPC 7508F USER S MANUAL Page 1 3 Chapter 1 Introduction 1 3 SYSTEM SPECIFICATIONS MAINBOARD PROX 7500 e CPU TYPE Intel Celeron M ULV 1 0GHz on board non L2 cache Auto detect voltage regulator e CHIPSET Intel 852GM ICH4 o MEMORY DDR Up to 1GB 1 x So DIMM Socket e CACHE Depended on CPU e REAL TIME CLOCK Embedded in Intel ICH4 South Bridge e BIOS PhoenixAward PnP BIOS 4Mbytes with VGA BIOS e KEYBOARD CONNECTOR Mini DIN connector Supports PS 2 Keyboard e MOUSE CONNECTOR Mini DIN connector Supports PS 2 Mouse e BUS SUPPORT N A Page 1 4 PPC 7308F USER S MANUAL Chapter 1 Introduction e DISPLAY LCD Panel 8 4 800 600 SVGA e WATCHDOG Selectable for NMI or Reset function e IDE INTERFACE 1 One IDE port support up to two IDE device 2 Support Ultra DMA 33 66 100 3 Compact Flash is connected at secondary IDE bus e SERIAL PORT Four high speed 16550 Compatible UARTs with Send Receive 16 Byte FIFOs COMI D Sub Connector for RS 232 COM2 D Sub Connector for RS 232 422 485 COMI 2 contain 5V or 12V power capability with 9 pin D sub connector on rear panel e PARALLEL PORT One 25 pin D Sub connector on rear panel Support for SPP ECP EPP Function Bi directional parallel port LAN ADAPTER Intel Chip RJ 45 jack onboard Support for 10 100 Base T Ethernet Support Wake On LAN function e USB CONNECTOR 2 USB
3. MANUAL 5 PPC 7508F Intel Celeron M 8 4 Panel PC System PPC 7508F M1 Copyright Notice PPC 7508F Panel PC System With LCD Touch screen OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist users in installing and setting up the system The information contained in this document is subject to change without prior any notice This manual is copyrighted April 2007 You may not reproduce or transmit in any form or by any means electronic or mechanical including photocopying and recording ACKNOWLEDGEMENTS All trademarks and registered trademarks mentioned herein are the property of their respective owners CE NOTICE This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which ca
4. Standard CMOS Features gt Frequency Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Managemen Save to CMOS and EXIT Y N Y gt PnP PCI Configura gt PC Health Status Esc Quit Ne Select Item F10 Save amp Exit Setup Save Data to CMOS When you confirm that you wish to save the settings your system will be automatically restarted and the changes you have made will be implemented You may always call up the setup program at any time to adjust any of the individual items by pressing the lt Del gt key during boot up PPC 7508F USER S MANUAL Page 4 25 Chapter 4 Award BIOS Setup 4 15 EXIT WITHOUT SAVING If you wish to cancel any changes you have made you may select the EXIT WITHOUT SAVING and the original setting stored in the CMOS will be retained The screen will be shown as below Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Managemen Quit Without Saving Y N N gt PnP PCI Configura gt PC Health Status Esc Quit Ne Select Item F10 Save amp Exit Setup Abandon all Datas Page 4 26 PPC 7508F USER S MANUAL SYSTEM ASSEMBLY
5. miN LANI s min 2 23 LAN LED CONNECTOR LANLED1 LAN LED Connector The pin assignment is as follows LANLED1 Page 2 26 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 24 KEYBOARD CONNECTOR KB1 PC AT Keyboard Connector The pin assignments are as follows 6 KBCLK 09 LE IN SA 2 25 PS 2 MOUSE CONNECTOR MS1 PS 2 Mouse Connector The pin assignments are as follows 6 MSAK _______ lx PPC 7508F USER S MANUAL Page 2 27 Chapter 2 Hardware Configuration 2 26 HDD LED CONNECTOR HDLED1 HDD LED Connector The pin assignment is as follows i at i aca 2 27 POWER BUTTON JPW1 Power Button E B The pin assignments are as follows 2 28 POWER LED CONNECTOR PWLED1 Power LED Connector The pin assignments are as follows PWLED1 Page 2 28 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 29 UNIVERSAL SERIAL BUS CONNECTOR USB1 Universal Serial Bus Connector The pin assignments are as follows ASSIGNMENT 5V USBO USB2 Universal Serial Bus Connector The pin assignments are as follows PPC 7508F USER S MANUAL Page 2 29 Chapter 2 Hardware Configuration USB3 Universal Serial Bus Connector The pin assignments are as follows ASSIGNMENT USB4 Universal Serial Bus Connector The pin assignments are as follows 1 2 USB4 Page
6. 2 30 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 30 MEMORY INSTALLATION This system is enhanced with 1 DDR DRAM banks which support up to IG DRAM BANK CONFIGURA TION DIMM 1 TOTAL MEMORY 128M 128MB 256M 256MB 512M 512MB 2 31 INVERTER CONNECTOR JINV1 Inverter Connector The pin assignments are as follows 5 ENVEE Inverter backlight On Off control signal PPC 7508F USER S MANUAL Page 2 31 Chapter 2 Hardware Configuration 2 32 POWER MODULE POWER1 Power Module The pin assignments are as follows POWER1 Page 2 32 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 33 COMPACT FLASH CONNECTOR CF1 Compact Flash Connector The pin assignments are as follows PIN PIN DM 2 oz A4 Bo 2 DB JS D6 13 D4 GND 36 sw _____ OND LL mois 5V DO 46 PDIAG 233 bo 48 D X 25 50 PPC 7508F USER S MANUAL Page 2 33 Chapter 2 Hardware Configuration 2 34 PCI 104 CONNECTOR PC104PLUS1 PCI 104 Connector The pin assignments are as follows EA SS SS ON EAS PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT c ce ao be mesEN ADM fe ADI2 BS 133V PAR BIO DIO SDONE stor sii D11 GND BI DIZ DEVSELI RAMEI fen DIS 3 3V BI DIS CBE aos Bis DIS GND BIG DIG ADIO BIT DIT 133V msmo Bis D18 IDSEL2 HI BIO DIS PC104PLUS1 B20 D20 GND
7. B21 D21 AD27 B22 D22 ADSI B23 D23 NC GNTIO GND SV Page 2 34 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 35 CPU FAN CONNECTOR JCFANI CPU Fan Connector ASSIGNMENT GROUND JCFAN1 2 36 SYSTEM FAN CONNECTOR JSFAN1 System FAN Connector JSFAN1 2 37 SERIAL ATA CONNECTOR SATA1 Serial ATA Connector ASSIGNMENT GND 4 GND o P GND 4 6 SATAHDRRXPO 7 GND OO GND PPC 7508F USER S MANUAL Page 2 35 Chapter 2 Hardware Configuration 2 38 RESET amp SPEAKER CONNECTOR J1 Reset and Speaker Connector GND GND Page 2 36 PPC 7508F USER S MANUAL SOFTWARE UTILITIES Page 3 1 Chapter 3 Software Configuration 3 1 INTRODUCTION Enclosed with our PPC 7508F package 1s our driver utility which may comes in a form of a CD ROM disc or floppy diskettes For CD ROM disc user you will only need some of the files contained in the CD ROM disc please kindly refer to the following chart Assume that CD ROM drive is D For VGA driver installation D Driver FLASH For BIOS update utility D Driver LAN For LAN Driver installation D Driver Sound Realtel ALC202A AC97 For Sound driver installation D Driver UTILITY Intel Chipset Software Installation Utility For Win 2000 XP D Driver USB 2 0 USB 2 0 Software Installation Utility For Win 98SE 2000 ME XP D Driver TOUCH For Elo Touch screen driver
8. Hardware and click Device Manager button Double Click USB Root Hub Select Driver Click Install to install the driver Follow the instructions on the screen to complete the installation Click Finish after the driver installation 1s complete eee ae 3 8 TOUCH SCREEN DRIVER UTILITY To install kindly refer to the readme txt file found each separate file of the Driver Disc PPC 7508F USER S MANUAL Page 3 9 Chapter 3 Software Configuration 3 9 WATCHDOG TIMER CONFIGURATION The Watch dog Timer has a programmable time out ranging from 1 to 255 minutes with one minute resolution or 1 to 255 seconds with 1 second resolution The units of the WDT timeout value are selected via bit 7 of the WDT_TIMEOUT register which is located on I O Port address 0x865h The WDT time out value is set through the WDT VAL Runtime register which is located on I O Port address 0x866h Setting the WDT VAL register to 0x00 disables the WDT function Setting the WDT VAL to any other non zero value will cause the WDT to reload and begin counting down from the value loaded Setting the Register located on I O address 0x867h and 0x868h as 00h to finish timer configuration Example Program Example Code Enable Watch Dog Timer mov dx 800h 65h Time counting Unit minute or second mov al 80h al 00h minute or al 20h second out dx al mov dx 800h 66h mov al 20 al Watch Dog Timer Second s 20
9. 4 Award BIOS Setup VIA ONCHIP IDE DEVICE The options for these items are found in its sub menu By pressing the lt ENTER gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility OnChip IDE Device OnChip Primary PCI IDE Item Help IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA AR e OnChip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Secondary Slave UDMA IDE HDD Block Mode Enabled Tl Move Enter Select PU PD Value Fl0 Save ESC Exit Fl General Help FS Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 OnChip Primary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately 2 Primary Master Slave PIO Secondary Master Slave PIO The four IDE PIO fields allow you to set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes O through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device 3 Primary Master Slave UDMA Secondary Master Slave UDMA Ultra DMA 33 implementation 1s possible only 1f your IDE hard drive supports it and the operating environment includes a DMA driver Win
10. Diagram for System Power Assembly A 4 Exploded Diagram for I O Port Assembly A 5 Exploded Diagram for Motherboard cc cece eee eee A 6 Exploded Diagram for LCD Assembly A 7 Exploded Diagram for System Cable A 8 Exploded Diagram for System Inverter Board A 9 Exploded Diagram for Touch Panel A 10 Exploded Diagram for Front Panel A 11 Exploded Diagram for System I O Side A 12 Exploded Diagram for Heatsink cece cece eee eee ros A 13 Exploded Diagram for Hard Disk Drive A 14 Exploded Diagram for Hard Disk Drive Holder A 15 Exploded Diagram for Power Holder A 16 APPENDIX B TECHNICAL SUMMARY Block Dido a EE B 2 erupt MAD id dia B 3 REC Ce EMOS RAM Map casi etam eR epp B 4 Timer amp DMA Channels Map mm B 5 DOG Memory MID sata seios stis aset mee M B 6 INTRODUCTION Page 1 1 Chapter 1 Introduction 1 1 ABOUT THIS MANUAL Thank you for purchasing our Panel PC Itis an updated system designed to be comparable with the highest performance of IBM AT personal computers It provides faster processing speed greater expandability and can handle more tasks This manual 1s designed to assist you on how to make the proper Installation to set up the system I
11. Page A 1 Appendix A System Assembly EXPLODED DIAGRAM FOR CF CARD HOOK 02 7508 CF HOOK 20 025 03061098 M3 L5 F NYLOK 22 215 30005111 8 9kgf cm 1 Name P N No Torsion oy Page A 2 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR FANLESS BACK COVER 8 ul o 1 TL ul 0 PPC 7508F USER S MANUAL Page A 3 Appendix A System Assembly EXPLODED DIAGRAM FOR SYSTEM POWER ASSEMBLY I Ef TM jii Jj 480458 TILL A uH guit TL E 06 power ASSEMBLY gt Pl 05 M3_L5_F_NYLOK_ 22 215 30005111 8 9kgf cm 1 No Name P N No Torsion fory Page A 4 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR I O PORT ASSEMBLY ae qn p t i L1 Ene suas t 08 W3 L5 F NYLOK 22 215 30008111 B 9kar enl 5 01 COM Port BOSS 22 692 40048051 8 9kgf cm 6 No Name P N No Torsion fory PPC 7508F USER S MANUAL Page A 5 Appendix A System Assembly EXPLODED DIAGRAM FOR MOTHERBOARD ft tl ll 1900001 ll Prox 1500 gt 10 1 10 M3 L6 S W 22 232 30060211 6 Tkgf cm 7 No Nome P N No Desin ot Page A 6 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR LCD ASSEMBLY 1s r508 tco assener Cid a 1508 FANCES CASE 20 001 03061098 1 a usas Fanok __ 22 215 30005111 E 9igren 6 riz outs 10E Russen
12. cylinders e Head number of heads e Precomp write precompensation cylinders e Landz landing zone e Sector number of sectors e Mode Auto Normal Large or LBA Auto The BIOS automatically determines the optimal mode Normal Maximum number of cylinders heads sectors supported are 1024 16 and 63 Large For drives that do not support LBA and have more than 1024 cylinders PPC 7508F USER S MANUAL Page 4 5 Chapter 4 Award BIOS Setup LBA Logical Block Addressing During drive accesses the IDE controller transforms the data address described by sector head and cylinder number into a physical block address significantly improving data transfer rates For drives greater than 1024 cylinders VIDEO This category selects the type of video adapter used for the primary system monitor Although secondary monitors are supported you do not have to select the type in Setup Available Options are as follows EGA VGA Enhanced Graphics Adapter Video Graphics Array For EGA VGA SEGA SVGA or PGA monitor adapters CGA 40 Color Graphics Adapter power up in 40 column mode CGA 80 Color Graphics Adapter power up in 80 column mode MONO Monochrome adapter includes high resolution monochrome adapters HALT ON This category allows user to choose whether the computer will stop if an error is detected during power up Available options are All errors No errors All But keyboard All But Diske
13. please refer to our 2 5 COM RI and Voltage Selection Page 2 20 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 17 VGA CONNECTOR VGA1 VGA Connector The pin assignments are as follows PPC 7508F USER S MANUAL Page 2 21 Chapter 2 Hardware Configuration 2 18 LVDS CONNECTOR LVDS1 LVDS Connector The pin assignments are as follows EE ZCP OO 29 30 mim a C3 CIC LU LC Lc LE c LL LU mim Lc mim L1 L3 L3 cC LJ a 1 2 LVDS1 LVDS_VCC LVDS_VCC Page 2 22 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 19 POWER CONNECTOR JATX1 Power Connector The pin assignments are as follows PPC 7508F USER S MANUAL Page 2 23 Chapter 2 Hardware Configuration 2 20 HARD DISK DRIVE CONNECTOR IDE1 Hard Disk Drive Connector The pin assignments are as follows ASSIGNMENT ASSIGNMENT EE 43 44 IDE1 a PDA2 Page 2 24 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 21 PRINTER CONNECTOR JPRNT1 Printer Connector As to link the Printer to the card you need a cable to connect both DB25 connector and parallel port The pin assignments are as follows O 5900000000000 O 8000000000068 JPRNT 1 PPC 7508F USER S MANUAL Page 2 25 Chapter 2 Hardware Configuration 2 22 LAN CONNECTOR LANI LAN Connector The pin assignment is as follows 3 MIP 4 mir 5 min 6
14. ports on rear panel Internal USB ports use 2 0 pitch box header for connection All USB ports support USB 2 0 standard e SOUND ALC202A AC 97 Codec Interface Line IN Line OUT MIC IN PPC 7508F USER S MANUAL Page 1 5 Chapter 1 Introduction e HARDWARE MONITORING FUNCTION Monitor CPU Voltage CPU Temperature e LED INDICATOR Power LED HDD LED LCD PANEL TFT color LCD is manufactured by using very high brightness technology Some sequential pixels may not light or may light always but this is not a failure e LCD TYPE LCD Panel 8 4 Priority source AUO LVDS or similar model PIXEL PITCH According to the supplier s LCD specification e BRIGHTNESS According to the supplier s LCD specification e CONTRAST RATIO According to the supplier s LCD specification e POWER CONSUMPTION According to the supplier s LCD specification e VIEWING ANGLE According to the supplier s LCD specification e RESPONSE TIME According to the supplier s LCD specification e COLOR According to the supplier s LCD specification e LCD MTBF Page 1 6 PPC 7508F USER S MANUAL Chapter 1 Introduction According to the supplier s LCD specification e BACKLIGHT MTBF According to the supplier s LCD specification e DIMENSION According to the supplier s LCD specification TOUCH SCREEN ELO 8 4 5W Resistive touch screen E494781 GENERAL INFORMATION e POWER SUPP
15. the BIOS Basic Input and Output system a program stored on a ROM Read only Memory chip to initialize and configure your computer s hardware As the interface between the hardware and the operating system the BIOS enables you to make basic changes to your system s hardware without having to write a new operating system The following diagram illustrates the interlocking relationships between the system hardware BIOS operating system and application program Application Program O Operation System Z BIOS EX s o system Hardware Page 4 2 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 2 ENTERING SETUP When the system is powered on the BIOS will enter the Power On Self Test POST routines and the following message will appear on the lower screen PRESS lt DEL gt TO ENTER SETUP ESC TO SKIP MEMORY TEST As long as this message is present on the screen you may press the lt Del gt key the one that shares the decimal point at the bottom of the number keypad to access the Setup program In a moment the main menu of the Award SETUP program will appear on the screen Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Management Setup Set User Password gt PnP PCI Con
16. 2 V Fanl Speed Smart Fan1 Temperature N lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PC Health Status Setup Screen The PC Health Status Setup allows you to select whether to choose between monitoring or to ignore the hardware monitoring function of your system SHUTDOWN TEMPERATURE This item allows you to set up the CPU shutdown Temperature This function is only effective under Windows 98 ACPI mode CURRENT CPU TEMPERATURE This item shows you the current CPU temperature CURRENT SYSTEM FAN SPEED This item shows you the current System FAN speed 2 5 Vcore Vcc3 VBAT 5V 12V Show you the voltage of 2 5 Vcore Vcc3 VBAT 5V 12V Smart Fan1 Temperature To Set Fan control starting Temperature PPC 7508F USER S MANUAL Page 4 21 Chapter 4 Award BIOS Setup 4 10 FREQUENCY CONTROL Choose FREQUENCY CONTROL from the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Frequency Control Auto Detect PCI Clk Enabled Item Hel Spread Spectrum Enabled STR Menu Level N gt o lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Frequency Control Setup Screen This setup menu allows you to specify your settings for frequency control AUTO DETECT PCI CLK This item allows you to
17. 30 013 0120003 Wo None emo sim ory PPC 7508F USER S MANUAL Page A 7 Appendix A System Assembly EXPLODED DIAGRAM FOR SYSTEM CABLE 23 LCD RUBBER 30 013 0130003 E NVERTER CABLE 21 015 33203074 7 Far 7500 Lvos caste zr ozo sezonsi 1 aa iso Eno Touch CABLE 27 016 o9e0aTE2 1 is fio teo cunt zicore ossos0r 1 ie POWER LED CABLE 27 018 06906071 1 ir LED HOUSING _ 30 014 o4100008 2 MEAT AREA Etats 10 Mo Wone TIA Tein Jory Page A 8 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR SYSTEM INVERTER BOARD SEO TOUCH PCB _ s2 370 00T36801 1 21 IWERTER Pea 52101773680000 1 26 INVERTER MYLAR _ 30 056 02v00033 Pas scree SUPPORT 23 320 30320063 Monon fewo ese ju PPC 7508F USER S MANUAL Page A 9 Appendix A System Assembly EXPLODED DIAGRAM FOR TOUCH PANEL 34 ero TOUCH PANEL 5235100736814 ETE 3001315300044 si fau tco PaveL 52 351 00000002 30 Jero Lco HOLDER 20 029 03001068 Wem PW Wo ria vy Page A 10 PPC 7508F USERS MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR FRONT PANEL ATEO 4 rat ooe Jsacoricoziosoos al Cw uer erronee 1 35 Power ase _ 34 017 o2103009 17 Mo None Jem es CAT PPC 7508F USER S MANUAL Page A 11 Appendix A System Assembly EXPLODED DIAGRAM FOR SYSTEM I O SIDE az SWITCH CABLE ARTET
18. 6 ATAT100 Storage Support USB Support Identification of Intel Chipset Components in Device Manager 3 6 2 Installation of Utility for Windows 2000 XP The Utility Pack is to be installed only for Windows 2000 and XP program It should be installed right after the OS installation kindly follow the following steps 1 Place insert the Utility Disk into Floppy Disk Drive A B or CD ROM drive 2 Under Windows 2000 XP system go to the directory where Utility Disc is located Click Setup exe file for utility installation Follow the instructions on the screen to complete the installation 5 Once installation 1s completed shut down the system and restart in order for the changes to take effect p Page 3 8 PPC 7508F USER S MANUAL Chapter 3 Software Configuration 3 7 USB2 0 SOFTWARE INSTALLATION UTILITY 3 7 1 Installation of Utility for Windows 98SE 2000 XP Intel USB 2 0 Enhanced Host Controller driver can only be used on Windows 98SE Windows 2000 and Windows XP on Intel Desktop boards 1 Win 98SE program 2 Win 2000 program 3 Win XP program It should be installed right after the OS installation kindly follow the following steps 1 Place insert the Utility Disk into Floppy Disk Drive A B or CD ROM drive 2 Under Windows 98SE 2000 and XP system go to the directory where Utility Disc is located 3 Start the System wizard in control panel Click Start Settings Control Panel Select
19. A Ti rar coso 20 003 03002031 17 ao iome 20 003 0301031 17 Wo Nome PIN We resi bi Page A 12 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR HEATSINK 44 17508 HEATSINK po qo 43 M3 LS F NYLOK 22 215 30005111 8 9kgf cm 4 No Nome P N No Torsion ory PPC 7508F USER S MANUAL Page A 13 Appendix A System Assembly EXPLODED DIAGRAM FOR HARD DISK DRIVE EU Pad 21 006 06060001 1508 FANLESS pie COVER 20 004 03061097 Page A 14 PPC 7508F USER S MANUAL Appendix A System Assembly EXPLODED DIAGRAM FOR HARD DISK DRIVE HOLDER spo 22 212 3000601 20 029 03003031 5 49 212 No PPC 7508F USER S MANUAL Page A 15 Appendix A System Assembly EXPLODED DIAGRAM FOR POWER HOLDER s To 54 HDD BASE HOLDER2 20 029 03002031 53 M3 L6 22 212 30006011 8 9kgf cm EE T E 52 woo moLoeRz 20 029 03003031 2 si fron ruser soconscoriooos a ojos wase _ 23 312 30080101 ul 49 M3 L6 22 272 30006011 8 9kof cm 4 No Name P N No Torsion fory Page A 16 PPC 7508F USER S MANUAL TECHNICAL SUMMARY Page B 1 Appendix B Technical Summary BLOCK DIAGRAM IMVP IV VR Celeron M PROCESSOR asun opie KEE 478 Micro FCPGA Banias 130nmiDothan S nm 855GME GMCH VR FSB VCCP L SV 151 6225 133M HEA OOATH GG TH E 48 He DOMBULTCMISMPH 855GME i 732 Micro FCEGA MH DDR SO DI
20. A VOLTAGE SELECTION JP5 CPU VCCA Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION VCCA 1 8V VCCA 1 5V Manufacturing Default VCCA 1 8V PPC 7508F USER S MANUAL Page 2 17 Chapter 2 Hardware Configuration 2 15 CPU FREQUENCY SELECTION JP3 CPU Frequency Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION o Manufacturing Default 100MHz Page 2 18 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 16 COM PORT CONNECTOR There are four COM ports enhanced in this board namely COMI COM2 COM3 and COM4 COMI COM3 and COMA are fixed for RS 232 while COM2 is selectable for RS 232 422 485 COMI COMI Connector The COMI Connector assignments are as follows 6 DSRI COMI 8 CIS O9 RH o COM2 COM Connector The COM2 Connector assignments are as follows RS232 RS 422 RS 485 COM 6 DSR2 JRTS NC 8 CTS22 CTS nc fo R2 crs Nc PPC 7508F USER S MANUAL Page 2 19 Chapter 2 Hardware Configuration COM3 COM3 Connector The pin assignments are as follows ASSIGNMENT a0 OOOo 3000000 COM3 COMA COMA Connector The pin assignments are as follows 6 C L Z LI LJ e COM4 All COM port s pin 9 is selectable for RI 5V or 12V For more information
21. I 1 2 Page 2 8 PPC 7508F USER S MANUAL RI default o Chapter 2 Hardware Configuration 2 6 COM 3 RI amp VOLTAGE SELECTION JP9 COM3 RI amp Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION PPC 7508F USER S MANUAL Page 2 9 RI default o Chapter 2 Hardware Configuration 2 7 COM 4 RI amp VOLTAGE SELECTION JP8 COMA RI amp Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION Page 2 10 PPC 7508F USER S MANUAL RI default o Chapter 2 Hardware Configuration 2 8 RS232 422 485 COM2 SELECTION JP13 RS 232 422 485 COM2 Selection COM2 is selectable for RS 232 422 485 function The jumper settings are as follows COM 2 JUMPER SETTING JUMPER ILLUSTRATION FUNCTION pin closed 1 RS 232 default 1 2 3 4 9 10 1 2 5 6 7 8 PPC 7508F USER S MANUAL Page 2 11 Chapter 2 Hardware Configuration 2 9 BRIGHTNESS VOLTAGE SELECTION JP1 Brightness Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION 5V 2 default 3 Page 2 12 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 10 LVDS VOLTAGE SELECTION JP12 LVDS Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION o VCC 5 PPC 7508F U
22. LY DC 16V 30V input ATX 60W output e DRIVE BAYS Optional Ix Slim HDD Ix Compact Flash Type II Slot IDE On Board e CONSTRUCTION Electo Galvanized steel chassis Aluminium front bezel e DIMENSIONS 247mm x 185mm x 82mm 9 73 x 7 3 x 3 23 e NET WEIGHT 5kg PPC 7508F USER S MANUAL Page 1 7 Chapter 1 Introduction 1 4 SAFETY AND NOTIFICATION Following messages are safety reminders on how to protect your systems from damages And thus helps you lengthen the life cycle of the system 1 Check the Line Voltage a The operating voltage for the power supply should cover the range of DC 16V 30V otherwise the system may be damaged 2 Environmental Conditions a b C Es Place your PPC 7508F on a sturdy level surface Be sure to allow enough room on each side to have easy access Avoid extremely hot or cold places to install your PPC Avoid exposure to sunlight for a long period of time for example in a closed car in summer time Also avoid the system from any heating device Or do not use PPC 7508F when it s been left outdoors in a cold winter day Bear in mind that the operating ambient temperature is from O C up to 40 C Avoid moving the system rapidly from a hot place to a cold place or vice versa because condensation may come from inside of the system Place PPC 7508F against strong vibrations which may cause hard disk failure Do not place the syste
23. MM SS he Montara Modules i a 200266434 MHz LI Hub Link Inerface 1 5 emo fes E i ATA i CF CARD ICH4 82801 DB KETI 1 1 2 0 EXE 421 BGA 6 KETI Firm Ware Hub 4MB Flash KIOS E SIO Audio Code i 114 ALC202 CON COMA Kevbonrd COMI Page B 2 PPC 7508F USER S MANUAL Appendix B Technical Summary INTERRUPT MAP ASSIGNMENT System TIMER interrupt from TIMER O Keyboard output buffer full Cascade for IRQ 8 15 Serial port 2 Serial port 1 Available Floppy Disk adapter Parallel port 1 RTC clock ACPI Compliant System Serial port 3 Serial port 4 PS 2 Mouse Math coprocessor Hard Disk adapter Hard Disk adapter PPC 7508F USER S MANUAL Page B 3 Appendix B Technical Summary RTC STANDARD RAM BANK 114 Bytes of User RAM 00 01 02 03 04 05 06 07 08 09 OA OB OC OD Page B 4 PPC 7508F USER S MANUAL Appendix B Technical Summary TIMER amp DMA CHANNELS MAP Timer Channel Map Timer Channel System timer interrupt DRAM Refresh request Speaker tone generator DMA Channel Map DMA Channel Available 1 Available 2 Floppy Disk adapter 3 Available 4 Cascade 5 Available Available Available PPC 7508F USER S MANUAL Page B 5 Appendix B Technical Summary I O 8 MEMORY MAP Fixed I O Ranges Decoded by ICH2 I O Address Internal Unit Oh 08h DMA 9h 0Eh DMA Fh DMA Oh 18h DMA 9h 1Eh DMA Fh DMA Oh 21h Interrupt 4
24. Palette Snoop Disabled using a Plug and Play capable operating system Select No if you need the BIOS to configure non boot devices Toe Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PNP PCI Configuration Setup Screen The PNP PCI Configuration Setup describes how to configure PCI bus system PCI also known as Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers technical items which is strongly recommended for experienced users only RESET CONFIGURATION DATA Normally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system configuration has caused such a serious conflict that the operating system cannot boot RESOURCE CONTROLLED BY The Award Plug and Play Bios can automatically configure all of the booth and Plug and Play compatible devices However this capability means PPC 7508F USER S MANUAL Page 4 19 Chapter 4 Award BIOS Setup absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 By choosing manual you are allowed to configure the IRQ Resources and DMA Resources IRQ RESOURCES The options for these items are found in i
25. SER S MANUAL Page 2 13 Chapter 2 Hardware Configuration 2 11 LVDS PANEL RESOLUTION SELECTION JP10 LVDS Panel Resolution Selection The selections are as follows JUMPER SETTING JUMPER DUNG TION pin closed ILLUSTRATION 640 x 480 800 x 600 10 4 default 1024 x 768 15 1280 x 1024 Page 2 14 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 12 CMOS FUNCTION SELECTION JP2 CMOS Function Selection The selections are as follows JUMPER SETTING JUMPER al pin closed ILLUSTRATION NORMAL default CLEAR CMOS 1 2 To clear CMOS data user must power off the computer and set the jumper to Clear CMOS as illustrated above After five to six seconds set the jumper back to Normal and power on the computer PPC 7508F USER S MANUAL Page 2 15 Chapter 2 Hardware Configuration 2 13 RESET NMI SELECTION JP4 Reset NMI Clear Watchdog Selection The selections are as follows JUMPER FUNCTION JUMPER SETTING ILLUSTRATION Reset default JA User may select to use the Reset or NMI watchdog NMI also known as Non Maskable Interrupt is used for serious conditions that demand the processor s immediate attention it cannot be ignored by the system unless it is shut off specifically To clear NMI command user should short the Clear Watchdog pin via push button Page 2 16 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 14 CPU VCC
26. Win 98SE program 2 Win 2000 program 3 Win XP program 4 NT4 0 program 5 Linux program For more details on Installation procedure please refer to Readme txt file found on LAN DRIVER UTILITY Page 3 6 PPC 7508F USER S MANUAL Chapter 3 Software Configuration 3 5 SOUND DRIVER UTILITY 3 5 1 Introduction The Realtek ALC202A sound function enhanced in this system is fully compatible with Windows NT 4 0 Windows 2000 Windows XP and Linux Below you will find the content of the Sound driver 1 Win 2000 program 2 Win XP program 3 NT4 0 program 4 Linux program 3 5 2 Installation Procedure for Windows 9x NT 2000 XP 1 From the task bar click on Start and then Run In the Run dialog box type D Sound setup where DASoundipathname refers to the full path to the source files Click on the OK button or press the ENTER key Click on the Next and OK prompts as they appear 5 Reboot the system to complete the driver installation us PPC 7508F USER S MANUAL Page 3 7 Chapter 3 Software Configuration 3 6 INTEL CHIPSET SOFTWARE INSTALLATION UTILITY 3 6 1 Introduction The Intel Chipset Software Installation Utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured This is needed for the proper functioning of the following features Core PCI and ISAPNP Services AGP Support IDE ATA33 ATA6
27. bled TR CPU L1 amp L2 Cache Enabled SEA Y CPU L3 Cache Enabled Quick Power On Self Test Enabled Meest de First Boot Device SATA SCSI id Second Boot Device HDD 0 Boot Up Floppy Seek Enabled Boot Up NumLock Status On Typematic Rate Setting Disabled x Typematic Rate Chars Sec 6 x Typematic Delay Msec Security Option N gt o lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help FS Previous Values F6 Fail Safe Defaults F7 Optimized Defaults BIOS Features Setup Screen The BIOS FEATURES SETUP allow you to configure your system for basic operation The user can select the system s default speed boot up sequence keyboard operation shadowing and security A brief introduction of each setting is given below Virus Warning Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and alarm beep CPU L1 amp L2 CACHE This item allows you to enable LI amp L2 cache Page 4 8 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup QUICK POWER ON SELF TEST This item allows you to speed up Power On Self Test POST after power up the computer When enabled the BIOS will shorten or skip some check items during POST FIRST SECOND BOOT DEVICE The BIOS attempt to load the operating system from the devices in the sequenc
28. d parallel port controller with which I O address Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal Compatible or SPP unless you are certain your hardware and software both support one of the other available modes ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode Page 4 16 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup ONBOARD SERIAL PORT 3 ONBOARD SERIAL PORT 4 Select a logical COM port name and matching address for the third and forth serial ports Select an address and corresponding interrupt for third and forth serial port 4 7 POWER MANAGEMENT SETUP Choose POWER MANAGEMENT SETUP option on the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled Power Management User Define Video Off Method DPMS Video Off In Suspend Yes MODEM Use IRQ 3 Suspend Mode Disabled Soft Off by PWR BTTN Instant Off Menu Level gt PWRON After PWR Fail Off Wake on LAN Enabled Power On by Ring Disabled Resume by Alarm Disabled x Date of Month Alarm 0 x Time hh mm ss Alarm 0 0 0 Reload Global Timer Events FDD COM LPT Port Disabled PCI PIRQ A D Disabled Toe Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Power Managem
29. dows 95 OSR2 or a third party IDE bus master driver If you hard drive and your system software both support Ultra DMA 33 Page 4 14 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup select Auto to enable BIOS support IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support ONBOARD DEVICE The options for these items are found in its sub menu By pressing the lt ENTER gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility Onboard Device USB Controller Enabled Item Hel USB 2 0 Controller Enabled PE USB Keyboard Support Disabled AC97 Audio Init Display First USB Mouse Support Disabled Menu Level Auto Onboard AGP Tl Move Enter Select PU PD Value Fl0 Save ESC Exit Fl General Help FS Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 PPC 7508F USER S MANUAL USB Controller This should be enabled 1f your system has a USB installed on the system board and you want to use 1t Even when so equipped 1f you add a higher performance controller you will need to disable this feature USB Keyboard Support Select Enab
30. e Selection 2 10 2 8 RS232 422 485 COM2 Selection 2 11 2 9 Brightness Voltage Selection 2 12 2210 LVDS Voltage Selection 2n Ee dave 2 13 2 11 LVDS Panel Resolution Selection 2 14 2 12 Clear CMOS Selecon aaasta 2 15 2 13 Watchdog Reset NMI Selection eee eee 2 16 2 14 CPU VCCA Voltage Selection 0 cece 2 17 2 15 CPU Frequency Selection ccc eee eee 2 18 2AG COM Port Conn cior sidecar aadli eda 2 19 21 VOA COMECON as a 2 21 2 18 ALVDS COMECIOL uidet ansiosa ENSIS RE 2 22 219 Power CONNMEC ON iria oad lens eale 2 23 2 20 Hard Disk Drive Connector ccc cece eee eee ee ees 2 24 2 21 Primer Connector sra ds 2 25 2 22 LAN CONECT uriaddol dc 2 26 2223 LAN LED Connector seria 2 26 2 24 Keyboard Connector aii 2 27 2 29 9 2 Mouse CONMECL NS idad iii 2 27 2 26 HDD LED Connector 25 tese debate soi obiret eo ss 2 28 2 2 POWE BUON oeste inci 2228 2 20 Power LED Connector eii ico 2 28 2 29 Universal Serial Bus Connector uuuuue 2 29 2 50 Memory Installation iii edi Mo Le td diio 2 31 Contents 2 31 Inverter Connector usen 2 31 2232 Power Module autusse 2 32 2 33 Compact Flash Connector eee 2 33 2344 PE LOA Connector ridad dde 2 34 2235 CPU FanConnccor aint oda iran 2 35 2 30 System Pan Connector ia 2 35 2237 Denda ATA Conn
31. e Selection LVDS Voltage Selection LVDS Panel Resolution Selection CMOS Function Selection Watchdog Reset NMI Selection CPU_VCCA Voltage Selection CPU Frequency Selection VGA Connector LVDS Connector COM Port Connector Power Connector Hard Disk Drive Connector Printer Connector LAN Connector LAN LED Connector Keyboard Connector PS 2 Mouse Connector HDD LED Connector Power Button Power LED Connector USB Connector Memory Installation Inverter Connector IDE Power Module Compact Flash Connector PC104 Connector CPU Fan Connector System Fan Connector Serial ATA Connector Reset amp Speaker Connector Page 2 2 2 1 JUMPER amp CONNECTOR QUICK REFERENCE TABLE JP6 JP7 JP9 JP8 JP13 JP1 JP12 JP10 JP2 JP4 JP5 JP3 VGAI LVDSI COMI COM2 COM3 COMA JATXI IDEI JPRNT1 LANI LANLEDI KB1 MS1 HDLEDI JPWI PWLEDI USBI USB2 USB3 USB4 DIMMI JINVI POWERI CFI PC104PLUS1 JCFANI JSFANI SATAI JI PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 2 COMPONENT LOCATIONS INTEL 855GME E JPWIHDLED1 JPA ela MA SR Germ PPC 7508F Connector Jumper and Component locations PPC 7508F USER S MANUAL Page 2 3 Chapter 2 Hardware Configuration 2 3 HOW TO SET THE JUMPERS You can configure your board by setting the jumpers Jumper 1s consists of two or three metal pins with a plastic base mounted on the card and by using a small plastic cap Also k
32. e econ Selection 2101014 2 4 1121013 13 EB 4 LILI 2 100 MHz default LVDS Voltage LVDS Panel Resolution Selection VA S Selection ER THE d Lr 7 no oe VCC5V es T T BEE oh default COM 4 ae voce A CMOS Function electio n LEMA ka led Selection Olt sh cada 21 31 an E P 0 Normal Clear CMOS v VB PT O LESS COM 3 RI amp Voltage EEI psp RS232 422 485 COM2 Selection C7 Bj Selection I1 DO 20801 a E ka ae ES COM 1 RI 8 Voltage E ey Le Selection Uh Ld J Brightness Voltage Selection 1 ED OA OO EE Aat 4 aa Sel T i sine sos sus c o lg PET Ne 14 RI 12V E m 5V 25V default a ien default COM 2 RI amp Voltage i EE a Reset NMI Selection Selection LJ E 7100010 10000 D for a 2 E28 ERES H ES Reset NMI bo SILILIS ss default RI SV 12V default Page 2 6 PPC 7508F USER S MANUAL Chapter 2 Hardware Configuration 2 4 COM 1 RI amp VOLTAGE SELECTION JP6 COMI RI amp Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION PPC 7508F USER S MANUAL Page 2 7 RI default o Chapter 2 Hardware Configuration 2 5 COM 2 RI amp VOLTAGE SELECTION JP7 COM2 RI amp Voltage Selection The selections are as follows JUMPER SETTING JUMPER SELECTION Pin Closed ILLUSTRATION E
33. e selected in these items BOOT UP FLOPPY SEEK You may enable disable this item to define whether the system will look for a floppy disk drive to boot at power on or proceed directly to the hard disk drive BOOT UP NUMLOCK STATUS Select power on state for NumLock TYPEMATIC RATE SETTING Enable this item if you wish to be able to configure the characteristics of your keyboard Typematic refers to the way in which characters are entered repeatedly if a key is held down For example if you press and hold down the A key the letter a will repeatedly appear on your screen on your screen until you release the key When enabled the typematic rate and typematic delay can be selected TYPEMATIC RATE CHARS SEC This item sets the number of times a second to repeat a key stroke when you hold the key down TYPEMATIC DELAY MSEC The item sets the delay time after the key is held down before it begins to repeat the keystroke PPC 7508F USER S MANUAL Page 4 9 Chapter 4 Award BIOS Setup SECURITY OPTION This category allows you to limit access to the system and Setup or just to Setup The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt The system will boot but access to Setup will be denied if the correct password is not entered at the prompt A To disable security select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not ty
34. e setup menus TO SET A PASSWORD When you select this function the following message will appear at the center of the screen to assist you in creating a password Enter Password Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press the lt Enter gt key You may also press lt Esc gt to abort the selection and not enter a password LA User should bear in mind that when a password is set you will be asked to enter the password everything you enter CMOS setup Menu TO DISABLE THE PASSWORD To disable the password select this function do not enter any key when you are prompt to enter a password and press the lt Enter gt key and a message will appear at the center of the screen PASSWORD DISABLED Press any key to continue Press the lt Enter gt key again and the password will be disabled Once the password is disabled you can enter Setup freely Page 4 24 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 14 SAVE amp EXIT SETUP After you have completed adjusting all the settings as required you must remember to save these setting into the CMOS RAM To save the settings select SAVE amp EXIT SETUP and press lt Enter gt a display will be shown as follows Phoenix AwardBIOS CMOS Setup Utility
35. ector mirra dali 2 35 2 38 Reset amp Speaker Connector eee 2 36 CHAPTER 3 SOFTWARE UTILITIES Sl Introduction ie 3 2 32 NGA Diver UL is in 3 3 do Blas DIOS Update uste ias 3 4 3 4 LAN Driver UI aiii 3 6 259 Sound Driver UU sesos lan isos 3 7 3 6 Intel Chipset Software Installation Utility 3 8 3 7 USB2 0 Chipset Software Installation Utility 3 0 3 8 Touch Screen Driver Utility cce 3 10 3 9 Watchdog Timer Configuration ccccocccnnnnnnnnnnnnnnnnnnnnnnnnnss 3 11 CHAPTER 4 AWARD BIOS SETUP Al TOTROCUCHOM Ge lalla alasi taala a 4 2 4 7 Ehete SCN ase 4 3 4 3 The Standard CMOS Features essere 4 4 4 4 The Advance BIOS Features occcccccccnnnnnnnnnoniononcnnnnnnnnos 4 8 4 5 The Advanced Chipset Features oo 4 11 4 6 Integrated Peripherals irem 4 13 4 7 Power Management Setup sic eee e eee ee eens 4 17 4 8 PNP PCI Configuration erre 4 19 49 PC AEA Status aparar i temale aata 4 21 4 10 Frequency Voltage Control nine 4 22 4 11 Load Fail Safe Defaults eee 4 23 4 12 Load Optimized Defaults n erre 4 23 4 13 Password Setting i12 rtt eee Eutr Se eet 4 24 4 14 Save amp Exit Setup eee erit enne 4 25 4 15 Exit WitlhOUL Saving iier uiri DERI ERR SD 4 26 Contents APPENDIX A SYSTEM ASSEMBLY Exploded Diagram for CF Card Hook sssss A 2 Exploded Diagram for Fanless Back Cover A 3 Exploded
36. enable or disable auto detect PCI Clock SPREAD SPECTRUM When the system clock generator pulses the extreme values of the pulse generate excess EMI Enabling pulse spectrum spread modulation changes the extreme values from spikes to flat curves thus reducing EMI This benefit may in some cases be outweighed by problems with timing critical devices such as a clock sensitive SCSI device Page 4 22 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 11 LOAD FAIL SAFE DEFAULTS By pressing the lt ENTER gt key on this item you get a confirmation dialog box with a message similar to the following Load Fail Safe Defaults Y N 2 N To use the BIOS default values change the prompt to Y and press the Enter gt key CMOS is loaded automatically when you power up the system 4 12 LOAD OPTIMIZED DEFAULTS When you press lt Enter gt on this category you get a confirmation dialog box with a message similar to the following Load Optimized Defaults Y N N Pressing Y loads the default values that are factory setting for optimal performance system operations PPC 7508F USER S MANUAL Page 4 23 Chapter 4 Award BIOS Setup 4 13 PASSWORD SETTING User 1s allowed to set either supervisor or user password or both of them The difference is that the supervisor password can enter and change the options of the setup menus while the user password can enter only but do not have the authority to change the options of th
37. ent Setup Screen The Power Management Setup allows the user to configure the system to the most effectively save energy while operating in a manner consistent with your own style of computer use PPC 7508F USER S MANUAL Page 4 17 Chapter 4 Award BIOS Setup ACPI FUNCTION Users are allowed to enable or disable the Advanced Configuration and Power Management ACPI POWER MANAGEMENT This item allows you to select the Power Management mode SOFT OFF BY PWR BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The choices are Delay 4 Sec and Instant Off PWRON After PWR Fail This item allows you to select if you want to power on the system after power failure The choice Off On Former Sts WAKE ON LAN An input signal from PME on the PCI card awakens the system from a soft off state RESUME BY ALARM When Enabled your can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode Page 4 18 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 8 PNP PCI CONFIGURATION Choose PNP PCI CONFIGURATION from the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Resources Controlled By Auto ESCD Menu Level b x IRO Resources Press Enter Select Yes 1f you are PCI VGA
38. figurations Save amp Exit Setup gt PC Health Status Exit Without Saving Esc Quit Ne Select Item F10 Save amp Exit Setup Time Date Hard Disk Type Setup program initial screen You may use the cursor the up down keys to highlight the individual menu items As you highlight each item a brief description of the highlighted selection will appear at the bottom of the screen PPC 7508F USER S MANUAL Page 4 3 Chapter 4 Award BIOS Setup 4 3 THE STANDARD CMOS FEATURES Highlight the STANDARD CMOS FEATURES and press the lt ENTER gt key and the screen will display the following table Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Wed Feb 23 2005 Time hh mm ss Dos 324 52 Menu Level gt IDE Primary Master gt IDE Primary Slave Change the day IDE Secondary Master month year and IDE Secondary Slave century Video EGA VGA Halt On All But Keyboard Base Memory 640K Extended Memory 1013760K Total Memory 1014784K Toe Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults CMOS Setup screen In the above Setup Menu use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item Date lt Month gt lt Date gt and lt Year gt Ranges for each value are in the CMOS Setup Screen a
39. h 000D FFFFh Main Memory TOM registers in Host Controller 0010 0000 TOM Top of Memory 000E 0000h 000F FFFFh FWH Bit 7 1n FWH Decode Enable Register is set FFC8 0000h FFCF FFFFh FWH Bit 1 in FWH Decode Enable A Regt FFD8 0000h FFDF FFFFh FWH Bit 3 in FWH Decode Enable EE UM FFE8 0000h FFEF FFFFh FWH Bit 5 in FWH Decode Enable a O UE FFBO 0000h FFB7 FFFFh Register is set FFF8 0000h FFFF FFFFh FWH Always Enabled FFB8 0000h FFBF FFFFh The top two 64K blocks of this range can be swapped as described 1n Section 6 4 1 FF30 0000h FF3F FFFFh Register is set FF20 0000h FF2F FFFFh Register is set FF10 0000h FF1F FFFFh Register is set FFOO 0000h FFOF FFFFh Register is set Anywhere in 4GB range D110 LAN Controller Enable via BAR in Device 29 Function O D110 LAN Controller All Other Page B 8 PPC 7508F USER S MANUAL
40. h 25h Interrupt 8h 29h Interrupt Ch 2Dh Interrupt Eh 2Fh orwarder to LPC Oh 31h Interrupt 4h 35h Interrupt 8h 39h Interrupt Ch 3Dh Interrupt 0h 42h PIT 8254 3h IT E 4F orwarder to LPC 0h 52h IT 3h IT Oh orwarder to LPC Ih Processor I F 2h orwarder to LPC 3h Processor I F 4h orwarder to LPC Sh Processor I F 6h Forwarder to LPC Th Processor I F Oh RTC Ih RTC 2h RTC 3h RTC 4h RTC 5h RTC 6h RTC Th RTC Page B 6 PPC 7508F USER S MANUAL Appendix B Technical Summary I O Address Read Target Write Target Internal Unit 80h DMA Controller DMA controller amp DMA LPC PCI 81h 83h DMA Controller DMA Controller 84h 86h DMA Controller DMA Controller amp DMA LPC or PCI DMA Controller DMA Controller 88h DMA Controller DMA Controller amp DMA LPC or PCI 89h 8Bh DMA Controller DMA Controller 8Ch 8Eh DMA Controller DMA Controller amp DMA LPC or PCI FOh See Note 3 FERR IGNNE Processor interface Interrupt Controller Notes 1 Only if IDE Standard I O space is enabled for Primary Drive Otherwise the target is PCI 2 Only if IDE Standard I O space is enabled for Secondary Drive Otherwise the target is PCI 3 If POS DEC EN bit is enabled reads from FOh will not be decoded by the ICH2 If POS DEC EN is not enabled reads from FOh will forward to LPC PPC 7508F USER S MANUAL Page B 7 Appendix B Technical Summary Memory Decode Ranges From Processor Perspective 0000 0000
41. ight consider making any changes would be if you discovered that data was being lost while using your system PPC 7508F USER S MANUAL Page 4 11 Chapter 4 Award BIOS Setup DRAM TIMEING SELECTABLE The value in this field depends on performance parameters of the installed memory chips DRAM Do not change the value from the factory setting unless you install new memory that has a different performance rating than the original DRAMs CAS LATENCY TIME When synchronous DRAM 1s installed the number of clock cycles of CAS latency depends on the DRAM timing DRAM RAS TO CAS DELAY This item let you insert a timing delay between the CAS and RAS strobe signals used when DRAM is written to read from or refreshed Fast gives faster performance and Slow gives more stable performance This field applies only when synchronous DRAM is installed in the system The choices are 2 and 3 DRAM RAS PRECHARGE TIME If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh the refresh may be incomplete and the DRAM may fail to retain data Fast gives faster performance and Slow gives more stable performance This field applies only when synchronous DRAM is installed in the system The choices are 2 amp 3 SYSTEM BIOS CACHEABLE Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a s
42. led 1f your system contains a Universal Serial Bus USB controller and you have a USB keyboard USB Mouse Support Select Enabled 1f your system contains a Universal Serial Bus USB controller and you have a USB Mouse AC97 Audio This item allows you to enable disable to support AC97 Audio Init Display First Select the initial Display type Page 4 15 Chapter 4 Award BIOS Setup SUPER IO DEVICE The options for these items are found in its sub menu By pressing the lt ENTER gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA SuperIO Device Enabled 3F8 IRQ4 2F8 IRQ3 378 IRQ7 SPP 3 Item Help Menu Level PF Tl Move Enter Select PU PD Value Fl0 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 Onboard FDC Controller Select Enabled if the system has a floppy disk controller FDC installed on the system board and you wish to use it If you install and in FDC or the system has no floppy drive select Disabled Onboard Serial Port 1 2 Select an address and corresponding interrupt for the first and second serial ports Onboard Parallel Port This item allows you to determine access onboar
43. m too close to any radio active device Radioactive device may cause interference 3 Handling a Avoid putting heavy objects on top of the system b C Do not turn the system upside down This may cause the floppy drive and hard drive to mal function Do not remove the diskette from the Floppy drive while the light is still on If you remove the diskette while the light is on you may damage the information on the diskette 4 Good Care a When the outside of the case 1s stained remove the stain with neutral washing agent with a dry cloth Never use strong agents such as benzene and thinner to clean the system If heavy stains are present moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth If dust has been accumulated on the outside remove it by using a special made vacuum cleaner for computers Page 1 8 PPC 7508F USER S MANUAL CHAPTER SYSTEM 2 CONFIGURATION Helpful information that describes the jumper amp connector settings and component locations Section includes Jumper amp Connector Quick Reference Table Component Locations Configuration and Jumper settings O Connector Pin Assignments Page 2 1 COMI RI amp Voltage Selection COM2 RI amp Voltage Selection COM3 RI amp Voltage Selection COM4 RI amp Voltage Selection Chapter 2 Hardware Configuration RS232 422 485 COM Selection Brightness Voltag
44. nd the week day will skip automatically Time lt Hour gt lt Minute gt and lt Second gt Use 24 hour clock format 1 e for PM numbers add 12 to the hour For example 4 30 P M You should enter the time as 16 30 00 Page 4 4 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup IDE Primary Master Slave IDE Secondary Master Slave The BIOS can automatically detect the specifications and optimal operating mode of almost all IDE hard drives When you select type AUTO for a hard drive the BIOS detect its specifications during POST every time system boots If you do not want to select drive type AUTO other methods of selecting drive type are available 1 Match the specifications of your installed IDE hard drive s with the preprogrammed values for hard drive types 1 through 45 2 Select USER and enter values into each drive parameter field 3 Use the IDE HDD AUTO DETECTION function in Setup Here 1s a brief explanation of drive specifications Type The BIOS contains a table of pre defined drive types Each defined drive type has a specified number of cylinders number of heads write precompensation factor landing zone and number of sectors Drives whose specifications do not accommodate any predefine type are classified as type USER e Size Disk drive capacity approximate Note that this size is usually greater than the size of a formatted disk given by a disk checking program e Cyls number of
45. nown as the jumper cap with a metal contact inside you are able to connect the pins So you can set up your hardware configuration by opening or closing pins The jumper can be combined into sets that called jumper blocks When the jumpers are all in the block you have to put them together to set up the hardware configuration The figure below shows how this looks like JUMPERS AND CAPS de da T 2 Pin Jumper 3 Pin Jumper Jumper Block Jumper Cap If a jumper has three pins for example labelled PINI PIN2 and PIN3 You can connect PINI amp PIN2 to create one setting and shorting You can either connect PIN2 amp PING to create another setting The same jumper diagrams are applied all through this manual The figure below shows what the manual diagrams look and what they represent Page 2 4 PPC 7508F USER S MANUAL JUMPER DIAGRAMS 55 JUMPER SETTINGS 7 Z y AM q Ni Chapter 2 Hardware Configuration Jumper Cap looks like this 2 pin Jumper looks like this 3 pin Jumper looks like this Jumper Block looks like this coo El E O 0O O 2 pin Jumper closed enabled looks like this 1 3 pin Jumper 2 3 pin closed enabled O looks like this 1 Ea Jumper Block 1 2 pin closed enabled looks like this oro 1 2 PPC 7508F USER S MANUAL Page 2 5 Chapter 2 Hardware Configuration PPC 7508F Jumper Illustration VCCA Voltage E CPU Frequency z
46. pe anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely Page 4 10 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 5 ADVANCED CHIPSET FEATURES Choose the ADVANCED CHIPSET FEATURES from the main menu the screen shown as below Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable X CAS Latency Time em Help Active to Precharge Delay X DRAM RAS to CASH Delay X DRAM RAS Precharge kaid DRAM Data Integrity Mode System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15M 16M Delayed Transaction AGP Aperture Size MB VGA Setting On Chip VGA On Chip Frame Buffer Size Boot Display CRT LFP PCI SERR NMI Disabled Tl Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Chipset Features Setup Screen This parameter allows you to configure the system based on the specific features of the installed chipset The chipset manages bus speed and access to system memory resources such as DRAM and the external cache It also coordinates communications between conventional ISA bus and the PCI bus It must be stated that these items should never need to be altered The default settings have been chosen because they provide the best opera ting conditions for the system The only time you m
47. se the user will be required to correct the interference at his own expense You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions WARNING Some internal parts of the system may have high electrical voltage And therefore we strongly recommend that qualified engineers can open and disassemble the system The LCD and touch screen are fragile please handle them with extra care All information contained in this document is subject to change without prior notice Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION Il About This Manual 4252 pmo reped i keenlase 1 2 12 Case TIOS AO cc 1 3 9 System Specification io 1 4 1 4 Safety and Notification esses 1 9 CHAPTER 2 SYSTEM CONFIGURATION 2 1 Jumper amp Connector Quick Reference Table 2 2 2 2 Component Locations diia 2 3 2 3 Howto sebthe JUIIDOIS section lo 2 4 2 4 COM IRI amp Voltage Selection 2 7 2 5 COM2RI amp Voltage Selection 2 8 2 6 COM3RI amp Voltage Selection uuuuuse 2 0 2 COM4RI amp Voltag
48. sec 5 cut dx al mov dx 800h 67h mov al Ooh out dx al mov dx 800h 68h Start Watch Dog Timer mov al 00h out ax al mov dx 800h 66h Disabled Watch Dog mov al 00n out dx al mov dx 800hn 67h mov al 00h out dx al mov dx 800h 68h Clear Status Bit mov al 00h out dx al Page 3 10 PPC 7508F USER S MANUAL CHAPTER AWARD 4 BIOS SETUP This chapter shows how to set up the Award BIOS Section includes O Introduction O Entering Setup O The Standard CMOS Features O The Advanced BIOS Features O The Advanced Chipset Features O Integrated Peripherals Power Management Setup O PNP PCI Configuration O PC Health Status O Frequency Control O Load Fail Safe Defaults O Load Optimized Defaults O Password Setting O Save and Exit Setup O Exit Without Saving Page 4 1 Chapter 4 Award BIOS Setup 4 1 INTRODUCTION This chapter will show you the function of the BIOS in managing the features of your system The PPC 7508F Panel PC is equipped with the BIOS for system chipset from Award Software Inc This page briefly explains the function of the BIOS in managing the special features of your system The following pages describe how to use the BIOS for system chipset Setup menu Your application programs such as word processing spreadsheets and games rely on an operating system such as DOS or OS 2 to manage such things as keyboard monitor disk drives and memory The operating system relies on
49. t contains five chapters The user can use this manual for configuration according to the following chapters Chapter 1 Introduction This chapter introduces you to the background of this manual illustration of the case and the specifications for this system The final page of this chapter indicates some safety reminders on how to take care of your system Chapter 2 System Configuration This chapter outlines the Prox 7500 components locations and their functions In the end of this chapter you will learn how to set jumper and how to configure the system for your own needs Chapter 3 Software Utilities This chapter contains helpful information for proper installations of the VGA utility LAN utility Sound utility and Flash BIOS update It also describes the function of the Watchdog Timer Chapter 4 Award BIOS Setup This chapter indicates on how to set up the BIOS configurations Appendix A System Assembly This section gives you the exploded diagram for the whole system unit Appendix B Technical Summary This section gives you the information about the Technical maps Page 1 2 PPC 7508F USER S MANUAL Chapter 1 Introduction 1 2 CASE ILLUSTRATION FRONT VIEW REAR VIEW o 000 0 0 070 o202080208090808 El RIGHT SIDE VIEW LEFT SIDE VIEW For FIX BOTTOM VIEW to qe unn t is e EB Ll aum m e mn Lo 1 3 H aum ome
50. ts sub menu By pressing the lt ENTER gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility IRQ Resources Item Help IRQ 3 assigned to PCI Device Menu Level 5 IRQ 4 assigned to IRQ 5 assigned to IRQ 7 assigned to PCI Device PCI Device PCI Device IRQ 10 assigned to IRQ 11 assigned to IRQ 12 assigned to IRQ 14 assigned to IRQ 15 assigned to Ti Move Enter Select F5 Previous Values Descriptions on each item above are as follows IRQ n Assigned to IRQ 9 assigned to PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device F6 Fail Safe Defaults Legacy ISA for devices compliant with the original PC AT bus specification PCI ISA PnP for devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture PU PD Value Fl0 Save ESC Exit Fl General Help F7 Optimized Defaults You may assign each system interrupt a type depending on the type of device using the interrupt Page 4 20 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup 4 9 PC HEALTH STATUS Choose PC HEALTH STATUS from the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature Disabled Item Help Current CPU Temperature 2 5V Menu Level gt VCore VCC3 VBAT 5V 1
51. tte and All But Disk Key BASE MEMORY Displays the amount of conventional memory detected during boot up EXTENDED MEMORY Displays the amount of extended memory detected during boot up TOTAL MEMORY Displays the total memory available in the system Page 4 6 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup HARD DISK ATTRIBUTES Type Cylinders Heads V P comp LZone Sect Capacity 306 128 305 17 10 615 300 615 17 20 615 300 615 17 940 512 940 17 940 512 940 17 615 65535 615 17 642 256 511 17 733 65535 733 17 900 65535 901 17 820 65535 820 17 855 65535 855 17 855 65535 855 17 306 128 319 17 733 65535 733 17 000 0000 000 00 612 0000 663 17 977 300 977 17 977 65535 977 17 1024 512 17 733 300 732 17 733 300 732 17 300 17 0000 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 17 65535 65535 65535 65535 65335 AUTO Award Hard Disk Type Table 4 4 6 8 6 4 8 5 15 3 5 7 8 7 0 4 5 7 7 5 7 5 4 5 9 7 11 15 8 11 11 9 a ata aa NnanM pwno PPC 7508F USER S MANUAL Page 4 7 Chapter 4 Award BIOS Setup 4 4 THE ADVANCED BIOS FEATURES Choose the ADVANCED BIOS FEATURES in the main menu the screen shown as below Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features Virus Warning Ena
52. xx bin 3 The screen will display the table below FLASH MEMORY WRITER V7 XX C Award Software 2001 All Rights Reserved Flash Type 49LF004B File Name to Program 7500xxxx bin Error Message Do You Want To Save BIOS Y N If you want to save up the original BIOS enter Y and press lt Enter gt If you choose N the following table will appear on screen FLASH MEMORY WRITER V7 XX C Award Software 2001 All Rights Reserved Flash Type 49LF004B File Name to Program 7500xxxx bin Error Message Are You Sure To Program Y N Select Y and the BIOS will be renewed When you are refreshing the BIOS do not turn off or reset the system or you will damage the BIOS Page 3 4 PPC 7508F USER S MANUAL Chapter 3 Software Configuration After you have completed all the programming the screen displays the table below FLASH MEMORY WRITER V7 XX C Award Software 2001 All Rights Reserved Flash Type 49LF004B File Name to Program 7500xxxx bin Verifying Flash Memory 7FFFF OK OU Write OK LINo Update UO Write Fail Fl Reset F10 Exit Please reset or power off the system then the Flash BIOS is fully implemented PPC 7508F USER S MANUAL Page 3 5 Chapter 3 Software Configuration 3 4 LAN DRIVER UTILITY 3 4 1 Introduction The PPC 7508F Panel PC is enhanced with LAN function that can support various network adapters Installation programs for LAN drivers are listed as follows 1
53. ystem error may result VIDEO BIOS CACHEABLE Select Enabled allows caching of the video BIOS resulting in better system performance However if any program writes to this memory area a system error may result On Chip VGA To Enable Disable the onboard display chip Boot Display To select the boot up display type Page 4 12 PPC 7508F USER S MANUAL Chapter 4 Award BIOS Setup PCI SERR NMI To Enable Disable the PCI SERR interrupt 4 6 INTEGRATED PERIPHERALS Choose INTEGRATED PERIPHERALS from the main setup menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals Laas ies ea gt Onboard Device Press Enter eH P SuperIO Device Press Enter Menu Level Onboard Serial Port 3 3E8 IRQ10 Onboard Serial Port 4 2E8 IRO11 WatchDog Support Disabled Toe Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Integrated Peripherals Setup Screen By moving the cursor to the desired selection and by pressing the lt F1 gt key the all options for the desired selection will be displayed for choice Ifbios setup menu item supports USB device boot it will cause Win9x detects the same storages twice when the system is rebooted and USB HDD will fail Note this cause just happen under Win9x the phenomenon is a limitation PPC 7508F USER S MANUAL Page 4 13 Chapter

Intel PPC-7508F User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents