INSTEON 2453-222(US) User's Manual
Contents
1. 9 5 2 26 E 10 10 ele eae eee ee eg ees 10 0 5 Ea 10 SPCCITICALIONS aar asaan ae T Sea cece estan Aae e aF reS aee aaa Ke Ee ao a oes enceb ends aaa EER 10 Troubleshoot EE EE A 12 Phase Bridge Detect Beacon RF Range 14 Replacing Fuse US version 14 Certification Maa een si e a aaa a aa a aa aaa aaa aaa 15 CEGAN ere REECE Cree 15 FCC and Industry Canada Compliance 15 Declaration Of vented al eater en aeaa iae Geeta ts abbot alten 15 LIMO Warranty axed eth exten ec adie et eee eee 15 fee 16 Page 2 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM About DIN Rail On Off Sense 1 Sense 2 Tools Needed2. Before you install DIN Rail behind a switch you must determine which type of switch have latching the default setting single momentary or dual momentary as each is wired differently If you are using DIN Rail with a single momentary or dual momentary switch you will program it for the corresponding switch after installation e Latching default mode switch has no central position it can be pressed on both the top and bottom and remains in that state once released e Single momentary switch can only be pressed in one place like a doorbell and returns to central position once released e Dual momentary switch can be pressed on both the top and bottom returns to central position once released Installation Turn off breaker fuse and verify power is off Disconnect wires from light fixture Strip away wire coating until you have 5 16 8mm of bare wire on the ends After ensuring the wires are not touching turn on breaker fuse Use a voltage meter to identify the fixture s line load and neutral wires then turn off breaker fuse again For reference write down the INSTEON I D on the side of the module and the load it is controlling Snap module onto DIN rail If installing next to another module allow 3 4 2 cm between modules for heat dissipation 7 Connect wires per diagram which corresponds to your installation Note sense lines carry very low current 0 35mA 240 0 17mA for 120 GOONS Without
3. 6 Adjust SettimnOS na pacandon eee 6 Change LED BriQhtni S N A E 6 ATE E E E 7 INSTEON Set 7 INSTEON Controllers Responders 1 nennen 7 Make DIN Raila Responde ii nentida A EA 7 Make DIN Rail a Controler 7 GOUD Sii iiaii SIE 8 gt 8 Make DIN Rail a Controller of Multiple 8 Remove DIN Rail as a Controller 9 Remove DIN Rail as a Responder 9 Remove DIN Rail as a Controller of Multiple Responders Unlink cccccccccccccececeeeeneceeeeececeeeeaeeeeaeeseeeeeseaeeeeaeeneneeeed 9 Factory OSCE
4. e The association between the controller and responder is called a link Link Controller Responder Note that a link is one way If you want control the other way making the responder a controller and the devices are capable of it simply add a link the other way Make DIN Rail a Responder Control DIN Rail from another INSTEON device 1 Press and hold controller button until it beeps Controller LED will start blinking 2 Tap DIN Rail paddle top or bottom to adjust load to on or off when scene is activated Connected load will respond appropriately 3 Press and hold DIN Rail set button until it double beeps DIN Rail Controller will double beep and its LED will stop blinking Controller Responder 4 Test by tapping controller button on and off Connected load will return to the state set in step 2 Note link just created is way See Make DIN Rail a Controller to add another link to keep the two products in synch or see Groups section Make DIN Rail a Controller Use DIN Rail to control other INSTEON devices 1 Press and hold DIN Rail set button until it beeps DIN Rail LED will start blinking green Page 7 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM 2 Turn responder on or any other state such as 50 or even off 3 Press and hold responder set button until it double beeps DIN Rail will double beep and its LED will stop blinking 4 Test by tapping DIN Rail padd
5. Optional PA pega Accessories Slotted screwdriver INSTEON Hub Wire cutter stripper Mini Remote Voltage Meter LED gt Paddle top on _ Fuse US only Paddle bottom Set a off button Neutral Line Installation Preparation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference This product is intended for installation in accordance with the local regulations in the regions intended for sale Use indoors only This product is not designed or approved for use on power lines other than 100 277VAC 50Hz or 60Hz single phase Attempting to use this product on non approved power lines may have hazardous consequences Use only indoors or in outdoor rated box sure that you have turned off the circuit breaker or removed the fuse for the circuit you are installing this product into Installing this product with the power on will expose you to dangerous voltages Connect using only copper or copper clad wire This product may feel warm during operation The amount of heat generated is within approved limits and poses no hazards To minimize heat buildup ensure the area surrounding this product is as clear of clutter as possible Each INSTEON product is assigned a unique INSTEON I D which is printed on the product s label reduce the risk of overheating and possible damage to other equipment do not use this prod
6. Switch Latching Sense 1 Neutral Neutral Neutral Neutral Single Momentary Dual Momentary Sense 1 Sense 1 Switch Neutral Neutral Neutral Neutral 8 After ensuring wires are firmly connected and that there is no exposed wire turn on breaker fuse After a few seconds load will turn on and DIN Rail LED will turn green 9 Test by tapping DIN Rail paddle top and bottom Load will turn on and off DIN Rail LED will turn green when load is on and red when load is off Page 4 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Switch Operation Mode By default DIN Rail is programmed for a latching switch If you are installing DIN Rail behind a single momentary or dual momentary switch you must change DIN Rail s local control switch operation to single momentary mode or dual momentary mode Change Mode 1 If installing a single momentary dual momentary switch change mode as follows a Press and hold set button until it beeps LED will start blinking green b Press and hold set button until it beeps a second time LED will start blinking red c Press and hold set button until it beeps a third time LED will start blinking green d Perform the step that applies e For single momentary slowly tap set button four times LED will continue blinking green e For dual momentary slowly tap set button five times LED will start double blinking green e To switch back to latching slowly tap set button six times LED wil
7. audited and that the manufacturer has agreed to a program of quarterly factory follow up inspections to verify continued conformance FCC and Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada RSS 210 Rev 7 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference including interference that may cause undesired operation of the device Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorise aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi mme si le brouillage est susceptible d en compromettre le fonctionnement The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio and television reception However there is no guarantee that interference will not occur in a particular installation If this device does cause such interfe
8. even after factory reset Scene memberships exist in the responder Check fuse to ensure it is not broken Look in the rear of the box for a group of wires all tied together with a wire nut Those are the Neutral wires Pull a Neutral from nearby junction box Install additional INSTEON devices to strengthen INSTEON signals US applications Add a Range Extender Move controller within range of DIN Rail Power line signals can t travel through some power filters Plugging the controller directly into a wall outlet works best Install filters where device s are causing line noise Install additional INSTEON devices to strengthen INSTEON signals Install a power line signal blocker in your home to keep X10 signals from neighboring homes from interfering Consider not using DIN Rail in X10 mode Use software to remove membership or perform a factory reset Install an in line noise filter between the load and DIN Rail Install additional INSTEON devices to strengthen INSTEON signals Connect power to the device If the INSTEON device is still available remove it from DIN Rail and then re add it Perform a factory reset Power cycle the device Perform a factory reset Add responder to scene again at desired scene on level Add DIN Rail to scene again at desired scene on level Remove responder from DIN Rail scene Page 13 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Phase Bridge Dete
9. from device A and then device B The and both devices LEDs will remain in synch Scenes Devices in a scene can each have different settings This provides for advanced lighting audio etc scene creation Software is recommended for scene management Example of a scene with 1 controller and DIN Rail as a member with the load on Press hold controller button until it beeps Controller LED will start blinking green 2 Tap controller set button Controller LED will start double blinking green 3 Tap DIN Rail on DIN Rail LED will be green Press and hold DIN Rail set button until it double beeps For each additional scene member a Adjust member to desired scene brightness b Press and hold set button until it double beeps 6 Press and hold controller set button until it double beeps Controller LED will stop blinking 7 Test by tapping controller button on and off DIN Rail and other scene responders will all respond appropriately a Make DIN Rail a Controller of Multiple Responders 1 Press and hold DIN Rail set button until it beeps LED will start blinking green 2 Tap DIN Rail set button LED will start double blinking green Page 8 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM 3 For each responder you are adding a Adjust responder to desired scene brightness state b Press and hold set button until it double beeps 4 Press and hold DIN Rail set button until it double beep
10. person shall be binding upon Seller or modify the terms of the above warranty and disclaimer Home automation devices have the risk of failure to operate incorrect operation or electrical or mechanical tampering For optimal use manually verify the device state Any home automation device should be viewed as a convenience but not as a sole method for controlling your home In no event shall Seller be liable for special incidental consequential or other damages resulting from possession or use of this device including without limitation damage to property and to the extent permitted by law personal injury even if Seller knew or should have known of the possibility of such damages Some states do not allow limitations on how long an implied warranty lasts and or the exclusion or limitation of damages in which case the above limitations and or exclusions may not apply to you You may also have other legal rights that may vary from state to state U S Patent No 7 345 998 International patents pending Copyright 2011 INSTEON 16542 Millikan Ave Irvine CA 92606 866 243 8022 www insteon com Page 16 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM
11. 50 brightness but it can be set anywhere from off to 100 brightness by following these steps 1 Press and hold set button until it beeps LED will start blinking green 2 Press and hold set button until it beeps a second time LED will start blinking red 3 Press and hold set button until it beeps a third time Page 6 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM LED will start blinking green 4 Tap set button once LED will start double blinking green 5 Press and hold set button until it beeps LED will turn green at brightness of connected load Press and hold DIN Rail on off buttons to brighten or dim LED to desired brightness 7 Tap set button until it double beeps DIN Rail will double beep and return to ready mode Error Blink By default DIN Rail LED blinks red for a few seconds to acknowledge a communication error with a responder This setting is adjustable via software or central controller only INSTEON Setup Some products have subtle differences in their setup procedures Please refer to the other device s owner s manual for details INSTEON Controllers Responders and Links Let s define a few terms e The INSTEON transmitter is called a controller e The INSTEON receiver is called a responder Note Some devices are controllers only e g motion sensors handheld remotes some are responders only e g FanLinc and some can be controllers and responders e g switches and dimmers
12. 522 Rev 1 21 2014 7 51 AM Weight 6 17 oz 175g Operating environment Indoors Operating temperature range 32 to 104 F 0 to 40 C Operating humidity range 0 90 relative humidity Storage temperature range 4 to 158 F 20 to 70 C Electrical Voltage 100VAC to 240VAC RF Frequency Electrical Frequency US 915 MHz EU 869 MHz AUS NZ 921 MHz 50 60Hz auto detected at power up Resistive Load type s Inductive capacitive Low voltage halogen US 15 240VAC EU 16A 240VAC AUS NZ 10A 240VAC Maximum load 3600W 240VAC Resistive 700W 240VAC Inductive Capacitive 2000W 240VAC Bulbs Low Voltage Halogen Minimum load None US 16A 5x20mm slow blow burn glass fuse BSeLIeRareapie ae No user replaceable fuse AUS NZ Hardwired remote control Yes either latching or momentary switches supported Retains all settings without power Yes saved in non volatile EEPROM Standby power consumption lt 1 watt Safety approval s ETL C Tick FCC 15 107 15 109 15 249 RSS 210 Certifications EN 300 220 2 301 489 3 AS NZS 4268 CISPR 22 UL 1472 IEC 60669 2 1 FCC ID SBPDR0O1 Troubleshooting Problem The LED on DIN Rail is not turning on at all and won t control my light Page 12 of 16 Possible Cause DIN Rail is not getting power tight and no bare wires are expo
13. DIN Rail On Off Owner s Manual 2453 222 US 2453 422 EU 2453 522 AUS NZ INSTEON Page 1 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM About DIN 3 Installation Preparation AA AEAEE OE chonscesdanducescututdeeenepesueunetecectstecersantuceseune 3 Identifying the Electrical Wires in Your Home North America 1 3 Identifying the Electrical Wires in Your Home Europe Australia N w 2 3 Identify SWITCH A 4 installati n 4 Switch Operation Mode 5 errr rere meer 5 3 Way Toggle Mode Latching Switches Only nnmnnn 5 Local Control Operations aa a ara eaea aaea a aaraa 6 Latching Wall Switch Default oer 6 Single Momentary Wall Switch sist erraria 6 Dual Momentary Wall
14. actical or add an additional dual band device RF Range Test e f LED is blinking Device is within RF communication range e If LED is not blinking Device is not within RF communication range Relocate if necessary and practical or add an additional dual band device 7 Tap set button DIN Rail module will stop beeping Other device LEDs will stop blinking If you have tried these solutions reviewed this owner s Manual and still cannot resolve an issue you are having with DIN Rail please call 866 243 8022 Replacing Fuse US version only Note Only the US version has a user replaceable fuse EU AUS NZ versions do not have a user replaceable fuse Turn off power to device Use a small screwdriver or similar tool to pry up fuse cover Remove fuse cover and fuse Replace fuse with 16A 5x20mm slow blow burn glass fuse Ensure fuse is centered in fuse holder and firmly press fuse and cover into place Restore power to device Ensure device is functioning properly 14 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO a nationally recognized independent third party testing laboratory The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U S and Canadian device safety standards that the manufacturing site has been
15. ct Beacon RF Range Test On Off module automatically bridges the electrical phases in your home via communications with other dual band devices on the other phase This is only important in 2 homes with powerline only INSTEON products or buildings with both 2 and 3 phase circuits The phase bridge detect beacon can also be used as an RF range test to see if your devices are within communication range You will need at least one other INSTEON dual band device installed 1 Press and hold set button until it beeps LED will start blinking green 2 Press and hold set button until it beeps a second time LED will start blinking red 3 Press and hold set button until it beeps a third time LED will start blinking green 4 Slowly tap set button 2 times LED will continue blinking green 5 Press and hold set button until it beeps Micro module will start beeping once per second LED will turn solid green 6 Check the LED behavior of other dual band devices Phase Bridge Detect Beacon e If the other dual band device is blinking green it is on the other phase Device provides a phase bridge to DIN Rail module e If the other dual band device is blinking it is on the same phase Device does not provide a phase bridge to DIN Rail module Relocate if necessary and practical e If the other dual band device is not blinking Device is not within RF range of DIN Rail module so it does not provide a phase bridge Relocate if necessary and pr
16. e disabled via software Blinks red or green during setup LED brightness Adjustable from off to bright Local control Commands supported as controller Yes On off Fast on off Begin brighten dim End brighten dim Commands supported as responder On off Fast on off Beep Software configurable Yes RF range Up 150 feet 50 meters open air Range may vary due to local interference Phase detect beacon Yes INSTEON device category INSTEON device subcategory amp X10 address X10 transmitter X10 status response X10 resume dim X10 minimum transmit level X10 minimum receive level X10 messages repeated lt n gt lt lt 2 0x02 Switched Lighting Control all frequencies US Ox2E EU 0x33 AUS NZ 0x34 1 optional comes unassigned Yes Supported Supported by setting local on level to zero 3 2 Vpp into 5 Ohms 20mV into 5 Ohms Screw DIN Rail connections Mechanical Mounting 35mm top hat DIN Rail Wires NA Max Cable Size 4 2 12 AWG 2 72mm Diameter Min Cable Size 1 5 2 15 AWG Line Neutral Load Sense 1 Sense 2 Case color White Set button Yes Plastic UV stabilized polycarbonate Beeper Yes Beep on button press Optional off by default LED 1 RGB Dimensions 3 14 H x 2 05 W x 2 48 D 80mm x 52mm x 63mm Page 11 of 16 2453 222 2453 422 2453
17. l start blinking green e Once the mode is selected press and hold set button until it double beeps LED will stop blinking and turn green if load is on or red if load is off 2 Test mode change by following the switch actions in the Latching Single Momentary or Dual Momentary tables below Load will respond appropriately 3 Way Toggle Mode Latching Switches Only Default Because DIN Rail module comes programmed for latching switches 3 way toggle mode is enabled by default Normally a latching switch reads the switch s up position as on and down position as off For example if you turn DIN Rail module on from the latching switch and off from another controller the switch is still in the up on position turning DIN Rail module back on from the switch would require you to tap the switch down then up again The 3 way toggle mode overrides this sense feature so in that same scenario turning DIN Rail module on at the switch and off from another controller so switch is in up on position you could then turn DIN Rail module on at the switch by tapping it down If you are installing DIN Rail module behind a single or dual momentary switch 3 way toggle mode is ignored If desired you can disable or re enable 3 way toggle mode by performing these steps Press and hold set button until it beeps LED will start blinking green Press and hold set button until it beeps a second time LED will start blinking red 3 Press and hold set button
18. le top and bottom Responder load will respond appropriately DIN Rail DIN Rail LED will turn green when load is on and red when load Is off Responder Controller Notes add multiple responders repeat steps 1 4 The link just created is one way See Make DIN Rail a Responder to add another link to keep the two products in synch or see Groups section Groups Devices a group share all the same settings e g on level ramp rate This keeps all group members synchronized Every device in a group is both a controller of and responder to all the other devices The most common example of a group is a 3 way lighting circuit 2 switches For simplicity we will assume that the desired group level is on The following steps will create a virtual 3 way circuit including device A and device B Turn devices Device loads will turn on 2 Press and hold device A set button until it beeps Device A status LED will start blinking green 3 Press and hold device set button until it double beeps Device A will double beep and its LED will stop blinking device A is now a controller of device B 4 Press and hold device B set button until it beeps Device B LED will start blinking green 5 Press and hold device A set button until it double beeps Device B will double beep and its LED will stop blinking device B is now a controller of device A Test by turning load on and off
19. mbol Environmental Information for Customers in the European Union European Directive 2002 96 EC requires that the equipment bearing this symbol on the product and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product DECLARATION OF CONFORMITY TO R amp TTE DIRECTIVE 1999 5 EC for the European Community Switzerland Norway Iceland and Liechtenstein Product category general consumer category 3 English This equipment is in compliance with the essential requirements and other relevant provisions of the European R amp TTE Directive 1999 5 EC Deutsch German Dieses Gerat entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999 5 EU Nederlands Dutch Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999 5 EC Svenska Swedish Denna utrustning star 6vere
20. n of the product in this Owner s Manual This warranty shall not apply to defects or errors caused by misuse or neglect If the product is found to be defective in material or workmanship or if the product does not perform as warranted above during the warranty period Seller will either repair it replace it or refund the purchase price at its option upon receipt of the product at the address below postage prepaid with proof of the date of purchase and an explanation of the defect or error The repair replacement or refund that is provided for above shall be the full extent of Seller s liability with respect to this product For repair or replacement during the warranty period call INSTEON at 866 243 8022 with the Model and Revision of the device to receive an RMA and send the product along with all other required materials to INSTEON ATTN Receiving 16542 Millikan Ave Irvine CA 92606 5027 Page 15 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Limitations The above warranty is in lieu of and Seller disclaims all other warranties whether oral or written express or implied including any warranty or merchantability or fitness for a particular purpose Any implied warranty including any warranty of merchantability or fitness for a particular purpose which may not be disclaimed or supplanted as provided above shall be limited to the two year of the express warranty above No other representation or claim of any nature by any
21. nsstammelse med de vasentliga egenskapskrav och relevanta bestammelser som framgar av direktiv 1999 5 EG Fran ais French Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999 5 EC Espanol Spanish Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999 5 CE Portugu s Portuguese Este equipamento esta em conformidade com os requisitos essenciais outras provis es relevantes da Directiva 1999 5 EC Italiano Italian Questo apparato conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999 5 CE Norsk Norwegian Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU direktiv 1999 5 EF Suomi Finnish Tama laite tyttaa direktiivin 1999 5 EY olennaiset vaatimukset siin asetettujen muiden laitetta koskevien m r ysten mukainen Dansk Danish Dette udstyr er i overensstemmelse med de v sentlige krav og andre relevante bestemmelser i Direktiv 1999 5 EF Polski Polish Urz dzenie jest zgodne z og lnymi wymaganiami oraz szczeg lnymi warunkami okreslonymi Dyrektyw UE 1999 5 EC Limited Warranty Seller warrants to the original consumer purchaser of this product that for a period of two years from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the descriptio
22. ps with no X10 address assigned Assign an X10 Address 1 Press and hold DIN Rail set button until it beeps DIN Rail LED will start blinking green 2 Send the X10 address times with or without commands Example A1 A1 A1 AON or A1 AON A1 AON A1 AON DIN Rail will double beep and its LED will stop blinking 3 Test by sending X10 on and off commands Load will turn on and off Remove X10 Address 1 Press and hold DIN Rail set button until it beeps DIN Rail LED will start blinking green 2 Press and hold DIN Rail set button until it beeps a second time DIN Rail LED will start blinking red 3 Send the X10 address times with or without commands DIN Rail will double beep and its LED will stop blinking 4 Test by sending X10 on and off commands Load will not respond Specifications General Product name DIN Rail On Off Brand manufacturer INSTEON US 2453 222 Manufacturer product number EU 2453 422 AUS NZ 2453 522 US 813922012828 UPC EU 813922012835 AUS NZ 813922012842 Warranty 2 years limited INSTEON INSTEON powerline mesh repeater Yes INSTEON RF mesh repeater Yes INSTEON controller Yes INSTEON responder Yes Maximum links scenes 400 Page 10 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Load brightness levels 32 locally 256 with software LED Green when load is on red when load is off Blinks red when responder does not acknowledge can b
23. rence which can be verified by turning the device off and on the user is encouraged to eliminate the interference by one or more of the following measures Re orient or relocate the receiving antenna of the device experiencing the interference Increase the distance between this device and the receiver Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver Consult the dealer or an experienced radio TV technician WARNING Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Declaration of Conformity Hereby INSTEON declares that this device is in compliance with the essential requirements and other relevant provisions of the following Directives 1 Low Voltage Equipment Directive 2006 95 EC 2 Electromagnetic Compatibility Directive 2004 108 EC 3 Hazardous Substance Directive 2005 95 EC Technical data and copies of the original Declaration of Conformity are available and can be obtained from INSTEON 16542 Millikan Ave Irvine CA USA User Information for Consumer Products Covered by EU Directive 2002 96 EC on Waste Electric and Electronic Equipment WEEE This document contains important information for users with regards to the proper disposal and recycling of INSTEON products Consumers are required to comply with this notice for all electronic products bearing the following sy
24. s DIN Rail LED will stop blinking 5 Test by tapping DIN Rail on and off All the responders will turn on and off Remove DIN Rail as a Controller Unlink If you no longer want DIN Rail to control another device or are removing DIN Rail it is important that you follow the instructions below for each responder 1 Press and hold DIN Rail set button until it beeps DIN Rail LED will start blinking green 2 Press and hold DIN Rail set button until it beeps a second time DIN Rail LED will start blinking red 3 Press and hold responder set button until it double beeps DIN Rail will double beep and LED will stop blinking 4 Test by tapping DIN Rail on and off Former responder will not respond Remove DIN Rail as a Responder Unlink If you no longer want a controller button to control DIN Rail follow these directions Note If you ever wish to un install DIN Rail remove all DIN Rail responder links otherwise controllers will retry commands repetitively creating network delays 1 Press and hold controller button until it beeps Controller LED will start blinking green 2 Press and hold controller button until it beeps a second time Controller LED will start blinking red 3 Press and hold DIN Rail set button until it double beeps Controller LED will stop blinking 4 Test by tapping controller button on and off DIN Rail will no longer respond Remove DIN Rail as a Controller of Multiple Responders Unlink Press and hold DIN Rail set but
25. sed Solution Make sure the circuit breaker is turned on Check junction box wires to ensure all connections are Check the light fixture to ensure all connections are tight and no bare wires are exposed 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM DIN Rail needs a Neutral wire in order to operate The switch I m replacing only has two wires DIN Rail and the controller are not within range of each other DIN Rail is not receiving signals from a controller The controller is plugged into a power strip Other appliance s are causing line noise Another controller a timer or stray X10 signals triggered DIN Rail DIN Rail may have an undesired responder membership The load turned on by itself Load connected to DIN Rail is producing electrical noise that is interfering with DIN Rail reception of power line signal DIN Rail responds to on commands but not off commands When press a button on DIN Rail it takes a long time for other INSTEON devices it is controlling to respond DIN Rail is trying to control a scene responder that is not powered on A surge or excessive noise DIN Raitis Tocked up on the power line occurred DIN Rail can turn off my responder but nothing happens when I send an on Responder scene level is off Controller can turn off DIN Rail DIN Rail does not respond to on DIN Rail may be added to a scene at its off state DIN Rail still controls devices
26. ton until it beeps DIN Rail LED will start blinking green 2 Press and hold DIN Rail set button until it beeps a second time DIN Rail LED will start blinking red 3 Tap DIN Rail set button DIN Rail LED will start double blinking red For each responder you are removing press and hold responder set button until it double beeps 5 Press and hold DIN Rail set button until it double beeps DIN Rail LED will stop blinking 6 Test by tapping DIN Rail on and off None of the former responders will respond Factory Reset All settings and scenes will be erased and return to factory default settings 1 Remove scene memberships from all controllers otherwise controllers will retry commands repetitively creating network delays see Remove DIN Rail as a Responder Unlink 2 Press and hold DIN Rail set button until it beeps LED will start blinking green 3 Press and hold DIN Rail set button until it beeps a second time LED will start blinking red 4 Press and hold DIN Rail set button until it beeps a third time LED will start blinking green Page 9 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM 5 Slowly tap set DIN Rail button 3 times LED will start double blinking green 6 Press and hold DIN Rail set button and don t let go DIN Rail will begin a long beep 7 Release DIN Rail set button after beeping has stopped After a few seconds DIN Rail will double beep DIN Rail will turn on and LED will turn green X10 Setup DIN Rail shi
27. uct to control loads in excess of the specified maximum s or install in locations with electricity specifications which are outside of the product s specifications If this device supports dimming please note that dimming an inductive load such as a fan or transformer could cause damage to the On Off the load bearing device or both If the manufacturer of the load device does not recommend dimming use a non dimming INSTEON on off switch USER ASSUMES ALL RISKS ASSOCIATED WITH DIMMING AN INDUCTIVE LOAD Identifying the Electrical Wires in Your Home North America only Line usually black may also be called hot live or power carries 100 277VAC electricity into the wall box Neutral usually white or white wire bundle commonly daisy chained from box to box Load usually black from a separate cable jacket Ground bare copper wire or metal fixture if grounded Identifying the Electrical Wires in Your Home Europe Australia New Zealand As wire colors vary from country to country make sure you always check your electrical wires with a voltage meter to correctly identify line load neutral and ground wires IMPORTANT If you have any difficulties or questions consult an electrician If you are not knowledgeable about and comfortable with electrical circuitry you should have a qualified electrician install the product for you Page 3 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Identify Switch
28. until it beeps a third time LED will start blinking green 4 Press and hold set button until it beeps a fourth time LED will start blinking red 5 Tap set button DIN Rail module will beep LED will start double blinking red 6 Press and hold set button until it double beeps LED will stop blinking 3 way toggle mode is now disabled or re enabled a4 5 of 16 2453 222 2453 422 2453 522 Rev 1 21 2014 7 51 AM Local Control Operations DIN Rails switch operation mode affects how it responds to commands so it s important to properly program DIN Rail for the correct type of switch you are installing DIN Rail on off buttons function exactly like the top and bottom of your wall switch Note LED will blink red for a few seconds if one or more responders do not acknowledge a message Latching Wall Switch Default Note that this table refers to the latching switch operation if 3 way toggle mode is disabled it is enabled by default Connected load responders Latching switch LED On ramped Off ramped Single Momentary Wall Switch Connected load responders Single momentary switch Double tap On Off On Off ramped instant Switch Dual Momentary Wall Switch Connected load responders Dual momentary switch Double tap Poe te leo Top ramped instant Off Off Bottom ramped instant Adjust Local Settings Change LED Brightness DIN Rail s LED is set at a default
Download Pdf Manuals
Related Search