Infinity PS210W User's Manual
Contents
1. PS210W PS212W WIRELESS POWERED SUBWOOFERS OWNER S GUIDE 120V IMPORTANT SAFETY PRECAUTIONS READ First 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufac turer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for2. Status LED WARNING TO REI DONOT EXPOSE Low Pass Selector Wireless Input Only Antenna Crossover Adjustment Subwoofer Level Control 120V 60Hz 2 Phase Switch Antenna A PS212W gt Antenna Sub Transmitter Antenna Transmitter Power Supply Input Transmitter 10 Selector Transmitter Sub Input PS210W PS210W PS212W 120V SYSTEM GONNECTIONS Choose either Wireless or Wired Connection then follow the appropriate instructions WIRELESS Connecting the Subwoofer for Wireless Applications SUBWOOFER OR LFE OUTPUT a Step 1 Connect a subwoofer cable from the subwoofer or LFE output of your receiver to the Sub In on the transmitter Step 2 Plug the transmitter module into the wall outlet and connect the included power supply and power cord to the transmitter Make sure the Transmitter Antenna is extended upward Step 3 Set the ID Code on the transmitter and subwoofer to the same position as described on page 6 When connected properly the LED on the rear of the subwoofer will be orange Step 4 Set the Low Pass Selector to the Off position NOTE Some receivers have two subwoofer outputs In that case use either conne
3. MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove finger prints or to wipe off dust The grille may be gently vacuumed Stains may be removed with an aerosol cleaner following its instructions Do not use any solvents on the grille All wiring connections should be inspected and cleaned or remade periodically The frequency of maintenance depends on the metals involved in the connections atmospheric conditions and other factors but once per year is the minimum In the event that your subwoofer ever needs service contact your ocal Infinity dealer or visit www infinitysystems com for a service center near you SPECIFICATIONS Frequency Response Amplifier RMS Power Amplifier Peak Power Crossover Frequencies Driver Operating Range RF Operating Frequency Dimensions x W x 0 Speaker with grille Transmitter Weight Speaker Transmitter t The peak dynamic power is measu voltage measured across the outpu of the transducer using a 50Hz si Features specifications and appearance are subject to change wit PS212W 2982 150 348 400 Watts 100 Watts 50Hz 150Hz when activated PS210W 27Hz 150 308 300 Watts 500 Watts 50Hz 150Hz when activated 24dB octave continuously adjustable 24dB octave continuously adjustable 12 300mm Up to 75 23m depending upon conditions 2 4GHz 8
4. x 14 3 8 x 18 3 4 457mm x 365mm x 476mm 1 8 x 4 7 8 x 3 7 8 29mm x 124mm x 98mm 20 3kg 0 5 10 0 2kg 0 250 Up to 72 22m depending upon conditions 2 4GHz 6 3 4 x 12 1 2 x 20 7 8 425mm x 318mm x 530mm 1 8 x 4 7 8 x 3 7 8 29mm x 124mm x 98mm 43 Ib 19 5kg 0 5 Ib 0 2kg ed by recording the highest center to peak tof a resistive load equal to wave burst cycles on 17 inimum impedance cycles off out notice PS210W PS212W 120V TECHNOLOGY PERFORMANCE DESIGN Harman Consumer Group Inc 250 Crossways Park Drive Woodbury NY 11797 USA 516 674 4468 USA only www infinitysystems com Infinity and MMD are trademarks of Harman International Industries Incorporated registered in the United States and or other countries Dolby is a registered trademark of Dolby Laboratories DTS is a registered trademark of DTS Inc Part No 406 000 05856 E 9 08 2008 Harman International Industries Incorporated All rights reserved H A Harman International Company
5. at least 10 apart can be operated using the same transmitter Simply set the channel selector on the transmitter and on the two subwoofers to the same channel Word About Wireless Products Infinity wireless subwoofers utilize advanced wireless transceivers operating in the 2 4GHz frequency band This is the same frequency band that is used for wireless home networks and high quality cordless phones It also allows for the transmission of high performance full spectrum sound to remote locations wirelessly Like all wireless devices your Infinity wireless subwoofer s operating range may vary depending upon variables such as building construc tion methods and materials atmospheric conditions and other sources of interference Please consult your Infinty dealer or visit www infinitysystems com for further information or assistance Wall Mounting the Transmitter Module NOTE The customer is responsible for the correct selection and use of mounting hardware available through hardware stores that will ensure the proper and safe wall mounting of the transmitter Step 1 Insert the two M3 x 4 machine screws through the wall bracket and into the rear of the transmitter module as shown in the figure below Step 2 Attach the transmitter module with wall bracket to the wall using suitable hardware and if necessary wall anchors ea O XX Q
6. long periods of time FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reason able protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a partic ular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help PS210W PS212W 120V 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus or the apparatus has been exposed to rain
7. acket for transmitter 2 x Pan head x 4 machine screws for attaching wall mount bracket to transmitter 4 x Small round self adhesive feet to be attached on transmitter s left side panel if transmitter is to be used vertically PLACEMENT ection very carefu gt call your dealer or visit www infinitysyst the listening room and how you align t nd right speakers is also of critical impo at the subwoofer integrate smoothly wit subwoofer s volume level too high wil oomy bass Setting the volume level too of the subwoofer are several additional facts on insta It is generally believed by most audio aut below 125Hz woofer within any listening room is not cri that the larger wavelengths of extremely nondirectional the fact is that when instal limited confines of a room reflections sta generated within the room will strongly inf any subwoofer system As a result the spec becomes important and it is strongly reco with placement before choosing a final loc ince the installation of a subwoofer can be somewhat more complicated an installing full range speakers it is essential that you read this ly prior to connecting the subwoofer to your system ould you have questions relating to your installation it is advisable ems com for assistance he performance of the subwoofer is directly related to its placement subwoofer with its
8. ation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation INTRODUCTION Infinity PS210W PS212W Powered Subwoofers The PS210W and PS212W powered subwoofers continue the long standing Infinity commitment to accurate sound reproduction Proprietary technology and engineering resources work together to deliver uncom promising low frequency performance in any stereo or multichannel home theater system Now that same exceptional Infinity low frequency performance is available wirelessly UNPACKING THE SUBWOOFER Carefully unpack the system If you suspect damage from transit report it immediately to your dealer and or delivery service Keep the shipping carton and packing materials for future use Open the package and verify the following contents Included 1 x Owner s manual 1 x USA warranty sheet 1 x Subwoofer 1 x 120V AC power cord for subwoofer 1 x 15 Audio cable RCA RCA 1 x Transmitter module 1 x Power supply for transmitter 1 x 120V AC power cord for transmitter power supply 1x 6 Audio cable RCA RCA 1 x Wall mount br
9. ctor WIRED Connecting the Subwoofer for Wired Applications If you have a Dolby Digital or DTS receiver processor with a low frequency effects LFE or subwoofer output SUBWOOFER OR LFE OUTPUT Sien Wireless ID Code A 2 s 0 LFE ey GW Phase 50Hz 150 2 fin Max 180 If your receiver processor does not contain a Dolby Digital or DTS processor but has subwoofer outputs RECEIVER PROCESSOR SUB OUT TH Wireless V LFE NOTE If your receiver processor has only one sub out you may use either the L or R input PS210W PS212W 120V C5 OPERATION Power On Connect your signal source such as an A V receiver or preamplifier to the transmitter if using a wireless connection or to the subwoofer if using a wired connection Two single RCA cords are provided While you would ordinarily use the short cable to connect to the transmitter or the long one to connect to the subwoofer either cable can be used depending on proximity to the signal source There is no need or benefit gained from connecting the same source to both the transmitter and the subwoofer However you could connect two separate sources to the subwoofer by utilizing both its wired and wireless connections Both signals will essentially be mixed and output by the subwoofer Plug your transmitter s if using a wireless connection and subwoofer s AC cord i
10. mines the highest frequency at which the subwoofer reproduces sounds If your main speakers can comfortably reproduce some low frequency sounds set this control to a lower frequency setting between 50Hz and 100Hz This will con centrate the subwoofer s efforts on the ultradeep bass sounds required by today s films and music If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies set the Crossover Adjustment control to a higher setting between 120Hz and 150Hz NOTE This control will have no effect if the LFE Input is used wired connection or if the Low Pass Selector is in the Off position wireless connection If you have a Dolby Digital or DTS processor receiver the Low Pass Frequency is set by the processor receiver Consult your owner s manual to learn how to view or change this setting ID Codes In the unlikely event that you experience interference when operating the system or if you have more than one set of subwoofer transmitters and receivers in operation you may change the channel in which the system operates On both the transmitter module and the subwoofer there is a four position D Code Selector Try setting both selectors to a different position Make sure that the Transmitter ID Code Selector and the Subwoofer 10 Selector are set to the same position the system won t function properly unless the positions match A maximum of two subwoofers
11. nto a wall outlet Do not use the outlets on the back of the receiver for the subwoofer Initially set the Subwoofer Level Control to the Min position Turn on your sub by pressing the Power Switch the rear panel Turn on your entire audio system and start a CD or movie soundtrack at a moderate level Auto On Standby Transmitter Wireless Connection Only The Status LED not shown will be lit in red when the unit is in Standby mode When the transmitter receives an audio signal from the source it will immediately turn on and the LED will turn to blinking green or solid green RED STANDBY No signal detected transmitter off GREEN BLINKING Transmitter is ON but has not established ink with the wireless sub GREEN SOLID Transmitter is ON and has already established a link with the wireless sub gt The transmitter will automatically enter Standby mode after mately 10 minutes when no signal is detected from your system Subwoofer With the Power Switch the position the Status LED on the back panel will remain lit to indicate the On Standby mode of the subwoofer RED STANDBY No signal detected Amp Off GREEN SUB ON Wired signal detected Amp On ORANGE SUB ON Wireless link with transmitter active The subwoofer will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system The sub
12. or moisture does not operate normally or has been dropped 15 Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the apparatus 16 To completely disconnect this apparatus from the AC Mains disconnect the power supply cord plug from the AC receptacle 17 The mains plug of the power supply cord shall remain readily operable 18 Do not expose batteries to excessive heat such as sunshine fire or the like The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture FCC Caution To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices FCC Radiation Exposure Statement This equipment complies with FCC RF radi
13. satellite peakers Setting the volume of the subwoofer in relation to the left rtance because it is essential the entire system Setting result in an overpowering ow will negate the benefits ation that may prove useful orities that low frequencies are nondirectional and therefore placement of a sub ical While in theory it is true ow frequencies are basically ing a subwoofer within the nding waves and absorptions uence the performance of ific location of the subwoofer mmended that you experiment ation Since your new wireless subwoofer does not need to be physically connected to your receiver or processor this process is now even easier Placement will depend upon your room and the amount and quality of bass required for example whether or not your room permits placement of the subwoofer near either satellite Be sure to leave a minimum of six inches between the wall and the por on the s bwoofer lt SUB RIGHT CHANNEL SPEAKER PRIMARY AREA Figure 1 This example shows the subwoofer positioned behind the right channel satellite speaker to re creat the actual location of bass instruments in an orchestra and or add impact to movie soundtracks PS210W PS212W 120V CONTROLS AND CONNECTIONS Rear Panels g gt Power Switch Line Level Input LFE Input Subwoofer ID Code Selector
14. woofer will then power on instantly when a signal is detected During periods of normal use the Power Switch can be left on You may turn off the Power Switch for extended periods of nonoperation e g when you are away on vacation Getting Started Confirm that the Status LED on the transmitter is on red or green the Status LED on the subwoofer is on red orange or green and an RCA cable is connected from a source unit to either the LFE Input of the subwoofer or transmitter L and inputs on the subwoofer Play a CD or video Use a selection that has ample bass information If using a wireless connection the Status LED on the transmitter should be lit solid green and the Status LED on the subwoofer should turn orange if connected wirelessly If the LED on the transmitter is blinking green and the LED on the subwoofer is in red or green a wireless link has not been established between the transmitter and the subwoofer If connecting directly to the subwoofer without using the wireless link the Status LED on the subwoofer should be lit green If the LED on the subwoofer remains red check CE PS210W PS212W 1201 that the RCA cable from the source to subwoofer wired connection or transmitter wireless connection is functioning properly and that it is fully inserted at both ends or that the Transmitter ID Code Selector and the Subwoofer ID Code Selector are set to the same channel Once
15. you have a green or orange LED on the subwoofer turn your Subwoofer Level Control up halfway so that the knob indicator points up You should now be hearing bass information coming from the subwoofer Adjust Level Set the overall volume control of the preamplifier or stereo to a com fortable level Adjust the Subwoofer Level Control until you obtain a pleasing blend of bass Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range Many users have a tendency to set the sub woofer volume too loud adhering to the belief that a subwoofer is there to produce lots of bass This is not entirely true subwoofer is there to enhance bass extending the response of the entire system so the bass can be felt as well as heard However overall balance must be maintained or the music will not sound natural An experienced istener will set the volume of the subwoofer so that its impact on bass response is always there but is never obtrusive Phase Control The Phase Switch determines whether the subwoofer speaker s piston like action moves in and out with the main speakers 0 or opposite the main speakers 180 Proper phase adjustment depends on several variables such as room size subwoofer placement and listening position Adjust the phase switch to maximize bass output at the listening position Crossover Adjustment The Crossover Adjustment Control deter
Download Pdf Manuals
Related Search