Impex PWR SURGE User's Manual
Contents
1. Tools Required to Assemble the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended this machine to be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1 A Connect the Right and Left Upright Beams 1 amp 2 by a Cross Brace 4 in the mid span Align the holes then secure the out side of the Upright Beam with a large Washer 59 and M10 x 1 Allen Bolt 55 on each end of the Cross Brace B Align the holes and secure them with two Brackets 26 four M10 x 3 7 Carriage Bolts 41 four 34 Washers 44 and four M10 Aircraft Nuts 47 on each end of the Cross Brace C Place Backrest Adjustment Bar 3 between the two Upright Beams on the selected bar holder to obtain desired incline of Backrest D Attach two Squat Bar Catches 13 to the top of the Upright Beams Secure them with two L shaped Pins 48 E Insert the Left Bar Catch 10 into the selected hole on the Left Upright Beam 2 Turn the Bar Catcher clockwise to lock it Repeat the same step for the other side DIAGRAM 1 STEP 2 See Diagram 2 A Slide the Sliding Block 7 onto the Main Seat Support 6 Secure it with a 3 8 Lock Knob 50 to a selected hole on the Main Seat Support B Attach the Front Stabilizer 8 to the Main Seat Support 6 Secure it with one M10 x 2 Ve Carriage Bolt 60 two M10 x 2 34 Carriage Bolts 42 34 Washers 44 and2. Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is recommended during exercise WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS HARDWARE IDENTIFIER PLACE WASHER END OF BOLT OR SCREW ON CIRCLE TO CHECK FOR CORRECT SIZE REPLACEMENT PARTS MILLIMETERS Thank you for purchasing IMPEX product Although we go to great effort to ensure O C C the quality of our products Occasionally errors or omissions occur Should you H Me me find either a defective or missing part in this product Please contact us for INCHES a replacement at the telephone number QUESTION sa 1 800 999 8899 1 2 5 8 3 4 NOTE When installing a Aircraft Nut also called Nylon or Lock Nut Please use two adjustable wrenches to tighten down the Nut Hold down the Bolt with one wrench and use the other wrench to turn the Nut clockwise Length o HEX HEAD BOLT C CE3 dumm 0 CARRIAGE BOLT ALLEN BOLT AIRCRAFT NUT FLAT WASHER ASSEMBLY INSTRUCTION
3. to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Ser
4. will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST www impex fitness com nfo impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10
5. End Cap 2 3 8 x 1 5 8 End Cap Axle Bushing Bracket Olympic Sleeve Foam Roll Olympic Spring Clip 2 3 8 Square End Cap 2 Square End Cap 1 Square End Cap 1 Square End Cap 1 End Cap 1 Round End Cap Foam Roll End Cap M10 x 4 34 Allen Bolt M10 x 5 8 Allen Bolt M6 x 1 3 8 Hex Bolt M8 x 5 8 Allen Bolt M10 x 3 Carriage Bolt M10 x 2 4 Carriage Bolt M8 x 34 Allen Bolt 34 Washer Vo Washer 5 8 Washer M10 x Aircraft Nut L shaped Pin 2 x 134 Sleeve 3 8 Lock Knob 2 3 8 x 2 Sleeve Arm Curl Pad Panel Screw Rubber Bumper M10 x 1 Allen Bolt Lock Pin Ye Lock Knob 2 Cone shaped End Cap Large Washer M10 x 2 Ve Carriage Bolt z N ANWDAAANNDOLDANDEOLORLANOOODKDAOOAOADRAOLONADDEONAARARARAANARRAA HA HAN Am o IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage
6. M10 Aircraft Nuts 47 C Attach the back of Main Seat Support 6 to the Cross Brace 4 Secure it with two Brackets 26 four M10 x 2 34 Carriage Bolts 42 34 Washers 44 and M10 Aircraft Nuts 47 D Insert the Leg Developer Holder 16 into the opening on the Front Stabilizer 8 Secure it with a v2 Lock Knob 57 E Attach two Backrest Supports 5 to the long pivot on the Sliding Block 7 Place the Headrest Bracket 12 in between the two Backrest Supports 5 Align the holes and lock the desired Headrest position with a Lock Pin 56 F Attach the Seat Bracket 9 to the short pivot on the Sliding Block 7 Secure it with one M10 x 4 3 Allen Bolt 37 two 34 Washers 44 and one M10 Aircraft Nut 47 DIAGRAM 2 STEP 3 See Diagram 3 A Attach the Leg Developer 15 to the bracket on the Leg Developer Holder 16 Secure it with an Axle 24 two 34 Washers 44 and two M10 x 5 8 Allen Bolts 38 B Insert one Foam Roll Tube 21 halfway through the holes on the Leg Developer Holder 16 Then insert two Foam Roll Tubes 21 halfway through the holes on the Leg Developer 15 Push six Foam Rolls 28 onto the Tubes from both sides Plug six Foam Roll End Caps 86 to the ends Slide the Olympic Sleeve 27 onto the weight post in front of the Leg Developer Attach the Olympic Spring Clip 29 to the Sleeve C NOTE When using the decline position to do A
7. NOTE Please read all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model PWR SURGE Retain This Manual for Reference 07 23 01 OWNER S MANUAL MP FITNESS PRODUCTS MARCY POWER SURGE BENCH IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 www impex fitness com pu TABLE OF CONTENTS BEFORE YOU BEGIN io de Ns aa dope Ee Oe EE ea GEN Dee N eR REI eek 1 IMPORTANT SAFETY NOTIGE SE HE ide bee ee de eb ee be se 2 HARDWARE IDENTIEIER ed sd ee ede bd ee ed ee ee eed be ed bn 3 ASSEMBLY INS TRUG HONS Si et se es es es een ee nak nnda o 4 EXPLODED DIAG RAM ics oue ke EG EE Ie aran A Fa KA bae Ve Et E Ge E N ee 8 PARTS EIS TEE SA ER Gua Ee calc s QuE 9 WARRANTY ainiai eg a De re d 10 ORDERING PARTS uses sg a aa BERG ke ee Iud M EG Re 10 BEFORE YOU BEGIN Thank you for selecting the MARCY Power Surge Weight Bench by IMPEX FITNESS PRODUCTS For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents
8. b exercise place at least 30lbs of weights on the post to hold down the Leg Developer DIAGRAM 3 STEP 4 See Diagram 4 A Place the Headrest Board 17 onto the Headrest Bracket 12 Secure it with two M8 x 34 Allen Bolts 43 and 5 8 Washers 46 B Place the Backrest Board 18 onto the Backrest Supports 5 Secure it with four M6 x 1 3 8 Hex Bolts 39 and 7 Washers 45 C Place the Seat Pad 19 onto the Seat Bracket 9 Secure it with four M8 x 5 8 Allen Bolts 40 and 5 8 Washers 46 Insert a L shaped Pin 48 into the selected hole on the Seat Bracket 9 to obtain the desired incline of the Seat D Attach the Arm Curl Pad 52 to the Arm Curl Stand 14 Secure it with two M8 x 5 8 Allen Bolts 40 and 5 8 Washers 46 Insert the Stand into the holder behind the Right Upright Beam For Arm Curl exercises remove the Leg Developer and Insert the Arm Curl Stand into the opening on the Front Stabilizer DIAGRAM 4 EXPLODED DIAGRAM PARTS LIST A m lt z O OONDOAARWDNY DESCRIPTION Right Upright Beam Left Upright Beam 1 Backrest Adjustment Bar Cross Brace Backrest Support Main Seat Support Sliding Block Front Stabilizer Seat Bracket Left Bar Catch Right Bar Catch Headrest Bracket Squat Bar Catch Arm Curl Stand Leg Developer Leg Developer Holder Headrest Board Backrest Board Seat Pad Upright Beam Panel Foam Roll Tube 2 3 x 2
9. vice Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts 4 2 3 Part Number 4 Date of Purchase 10
Download Pdf Manuals
Related Search