Impex MWM-8900 Owner's Manual
Contents
1. 8900 IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 gt O x 24 lt 7 gt c e www impex fitness com info impex fitness com MWM Tel 800 999 8899 Fax 626 961 9966 NOTE Please read all instructions carefully before using this Table of Contents Safety Notice Hardware Pack Resistance Chart Ordering Parts Model MWM 8900 Retain This Manual for Reference 08 12 05 OWNER S MANUAL Assembly Instruction TABLE OF CONTENTS BEFORE YOU BEGIN aaa era ren 1 IMPORTANT SAFETENO TIE dado 2 HARDWARE PACK dea sia wg ake aja wg maea adidas 4 ASSEMBLY 7 PARTS LIS Tas AAA ai 29 RESISTANCE CHART eeu deque igap ren 30 WARRANTIN Ainaa aa adada 31 ORDERING PARIS ivan 31 BEFORE YOU BEGIN Thank you for seleciing the MARCY MWM 8900 CORNER GYM by IMPEK INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any guestions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Custome2. Slide fourteen Weight Plates 54 onto the rear set of Guide Rods 4 Make sure the groove on the plates all face toward the front of the machine B Insert a Selector Rod 53 into the center holes Slide a Selector Stem 34 onto the two Guide Rods Slide a Y 1 4 Rubber Bumper 34 onto the Selector Rod C Repeat procedures A amp B above to install the other fourteen Weight Plates onto the front two Guide Rods Make sure the grooves face the back of the machine DIAGRAM 3 6 9 2 OO NG E NS i Zoll NG D LIKE amp STEP 4 See Diagram 4 A Do not tighten all Nuts and Bolts in this step until instructed to do so B Attach the Right Vertical Frame 5 to the Right Base Frame 1 Secure it with two M10 x 2 V Carriage Bolts 98 Y Washers 21 and M10 Aircraft Nuts 18 C Attach the Left Vertical Frame 6 to the Left Base Frame 2 Secure it with one M10 x 2 7 Carriage Bolt 98 3 Washer 21 and M10 Aircraft Nut 18 D Attach the Rear Vertical Frame 7 to the Rear Base Frame 3 Secure it with one M10 x 2 V Carriage Bolt 98 34 Washer 21 and M10 Aircraft Nut 18 DIAGRAM 4 10 STEP 5 See Diagram 5 A Do nat tighten all Nuts and Bolts in this step until instructed to do so B Place the Upper Frame 8 onto the Right Vertical Frame 5 and two Guide Rods 4 Secure the Upper Frame to the R
3. 17 STEP 10 See Cable Loop Diagram amp Diagram 10 A Attach the 102 Upper Cable 36 to the front opening on the Upper Frame 8 Attach a Pulley 64 to the opening Secure it with one M10 x 2 3 8 Allen Bolt 96 two Pulley Bushings 63 and one M10 Aircraft Nut 18 Draw the Cable towards the back of the machine Note Make sure the Ball Stopper is underneath the frame B Attach a Pulley to the opening on the Upper Frame Secure it with one M10 x 2 3 8 Allen Bolt 96 two Pulley Bushings 63 and one M10 Aircraft Nut 18 C Draw the Cable around the Pulley and downward Install a Pulley to the two Double Floating Pulley Brackets 32 Secure it with one M10 x 1 9 Allen Bolt 95 two 34 Washers 21 and one M10 Aircraft Nut 18 Let the bracket hanging for now Draw the Cable around the Pulley then upward to the open bracket on the Upper Frame D Install a Pulley to the bracket with a L shaped Cable Retainer 60 E Draw the Cable around the Pulley then downward to the Selector Rod 53 Attach the ring on the Selector Pin 262 to the Selector Rod 53 Securely thread the end of the Cable into the Selector Rod Use the Nut at the end of the Cable to tighten down the Bolt 18 DIAGRAM 10 19 STEP 11 See Cable Loop Diagram amp Diagram 11 A Clip one end of the 76 Butterfly Cable 37 to the slot on the Left Butterfly Adjustment Frame 50 Draw the Cable through the sl
4. 1 x 12 Bushing 1 x O 7 8 Bushing Y x Y 3 8 Bushing 4 3 8 x 1 34 Bracket 1 7 8 x 1 5 8 Rubber Bumper Y 2 12 x 1 Rubber Bumper 1 12 x 5 8 Rubber Bumper Short Chain C clip Long Chain 21 Cone shaped End Cap M10 x 2 7 8 Allen Bolt M10 x 5 8 Allen Bolt M10 x 1 Allen Bolt M10 x 1 34 Allen Bolt M10 x 2 3 8 Allen Bolt M10 x 2 34 Carriage Bolt M10 x 2 12 Carriage Bolt M12 x 4 3 8 Hex Bolt M12 x 3 Hex Bolt M8 x 2 1 Allen Bolt M8 x 1 5 8 Allen Bolt N 2 IT TIANG NHNANNNHNAN ANAH 2 NDOA wm MWM 900 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 Low Pulley 35 45 55 65 75 85 95 Lat Pull 15 25 35 45 55 65 75 Butterfly 10 17 24 31 38 45 52 Leg Press 30 50 70 90 110 130 150 Front Press 35 50 65 80 95 110 125 Vertical Press 30 43 56 69 82 95 108 WEIGHT PLATE Station 8 9 10 11 12 13 14 Low Pulley 105 115 125 135 145 155 165 Lat Pull 85 95 105 115 125 135 145 Butterfly 73 80 87 94 101 108 115 Leg Press 170 190 210 230 250 270 290 Front Press 140 155 170 185 200 215 230 Vertical Press 121 134 147 160 173 186 200 Numbers are approximate Actual weight may v
5. 431 previously installed in Step 12 Secure the end of Cable to the Bracket with one M10 x 1 Allen Bolt 94 two 34 Washers 21 and one M10 Aircraft Nut 18 DIAGRAM 13 23 STEP 14 See Diagram 14 Attach a Short Chain 88 to the open bracket on the Rear Vertical Frame 7 Secure it with one M10 x 1 Allen Bolt 94 two 9 Washers 21 and one M10 Aircraft Nut 18 B Connect the 94 Vertical Press Cable 39 to the Short Chain with a C clip 89 C Install a Pulley to an Angled Floating Pulley Bracket 31 D Draw the Cable around the Pulley then upward to the first open bracket on the Top Socket Assemble 9 E Install a Pulley to the bracket with a L shaped Cable Retainer 60 Draw the Cable over the Pulley to the second open bracket Repeat the same procedure to install another Pulley F Draw the Cable around the Pulley then downward to the Selector Rod 53 Attach the ring on the Selector Pin 62 to the Selector Rod Securely thread the end of the Cable into the Selector Rod Use the Nut at end of the Cable to tighten down the Bolt G After completing the cable installations come back to this step and adjust the length of the Short Chain 88 If the cables are too loose shorten the Chain 24 DIAGRAM 14 25 STEP 15 See Diagram 15 w m Attach the 216 Leg Press Cable 40 to the bracket on the back of Leg Press Frame 25 Secure it with
6. one M10 x 1 Allen Bolt 94 two 34 Washers 21 and one M10 Aircraft Nut 18 Draw the Cable to the open bracket on the Left Seat Support 11 Install a Pulley to the bracket Draw the Cable around the Pulley then back to the open bracket on the Leg Press Frame Install another Pulley Draw the Cable around the Pulley then through the opening on the Left Seat Support 11 and Left Vertical Frame 6 to the open bracket on the Left Base Frame 2 Install a Pulley to the bracket Draw the Cable underneath the Pulley then upward to the open bracket on the Vertical Press Base 23 Install a Pulley Draw the Cable around the Pulley then downward to the open bracket on the Rear Base Frame 3 Install a Pulley to the bracket Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket installed in Step 14 Secure it with one M10 x 1 Allen Bolt 94 two 34 Washers 21 and one M10 Aircraft Nut 18 26 STEP 16 See Diagram 16 A Place a Seat Pad 42 onto the Seat Incline Adjustment Frame 27 Secure it with two M8 x 1 5 8 Allen Bolts 102 and Y 5 8 Washers 20 Insert the Frame into the opening on the Left Seat Support 11 Use a Lock Knob 68 to secure the Seat at selected height B Insert two Foam Tubes 13 halfway through the holes on the Right Seat Support 10 and the Leg Developer 26 Push four Vinyl Foam Rolls 58 onto the Tube
7. upward to the Double Floating Pulley Bracket 32 previously installed in Step 10 Install a Pulley to the Brackets on selected hole After completing all the Cable installation come back to this step and check the tension of the Cable loop system If the cables are too loose move up the Pulley on the Bracket Move down the Pulley if the Cables are too tight F Draw the Cable around the Pulley then downward Install a Pulley to an Angled Floating Pulley Bracket 31 G Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket 31 previously installed in Step 11 Secure the Cable to the Bracket with one M10 x 1 Allen Bolt 94 two Y 32 Washers 21 and one M10 Aircraft Nut 18 21 DIAGRAM 12 STEP 13 See Diagram 13 A x xe J Attach the 49 Front Press Cable 38 to the small opening on the Right Vertical Frame 45 Secure the head of the Cable to the small opening with one M10 x 2 3 8 Allen Bolt 96 two 34 Washers 21 and one M10 Aircraft Nut 18 Draw the Cable to the open bracket on the Front Press Base 29 Install a Small Pulley 65 to the bracket Draw the Cable around the Small Pulley then back to the opening on the Right Vertical Frame 5 then to the open bracket on the Right Base Frame 1 Install a Pulley to the bracket with a L shaped Cable Retainer 60 Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket
8. ary Value for butterfly is for each arm 30 IMPEX ING LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Acc
9. d M10 Aircraft Nut 18 E Insert the Leg Press Adjustment Frame into the Leg Press Frame Use a Lock Knob 68 to secure it in selected position DIAGRAM 7 STEP 8 See Diagram 8 Insert the on the Right Butterfly 15 through a Butterfly Adjustment Frame 50 into the Butterfly Support Frame 12 Secure it with one M10 x 5 8 Allen Bolt 93 34 Washer 21 and Lock Ring 33 B Thread a T shaped Pull Pin 66 into the hole on the Right Butterfly from the bottom Use the Pin to adjust the Butterfly position C Repeat the same procedures A amp B above to install the Left Butterfly 14 D Attach the Front Press Base 29 to the Right Base Frame 1 Secure it with one Axle 59 two 34 Washers 21 and two M10 Aircraft Nuts 18 E Place the Front Press 16 onto the Front Press Base Secure it with four M10 x 2 9 Carriage Bolts 97 34 Washers 21 and M10 Aircraft Nuts 18 DIAGRAM 8 STEP 9 See Diagram 9 A Attach the Vertical Press Base 23 to the pivot on the Rear Vertical Frame 7 Secure it with one Axle 59 two Y 34 Washers 21 and two M10 Aircraft Nuts 18 Attach one Vertical Press Arm 24 to the Vertical Press Base Secure it with two M10 2 7 Carriage Bolts 98 34 Washers 21 and M10 Aircraft Nuts 18 C Repeat the same procedure to install the other Vertical Press Arm DIAGRAM 9 16 CABLE LOOP DIAGRAM
10. ight Vertical Frame with two M10 x 2 7 Carriage Bolts 98 one 4 3 8 x 1 9 Bracket 84 two 34 Washers 21 and two M10 Aircraft Nuts 18 C Secure the Upper Frame to the two Guide Rods with two M10 x 1 Allen Bolts 94 and Y 34 Washers 21 D Place the Top Socket Assembly 9 onto the two Guide Rods on the rear Secure them with two M10 x 1 Allen Bolts 94 and Y Washers 21 E Connect the Top Socket Assembly 9 Rear Vertical Frame 7 Upper Frame 8 and Left Vertical Frame 6 together Align the holes and secure them with two M10 x 2 7 Carriage Bolts 98 Y 34 Washers 21 and M10 Aircraft Nuts 18 STEP 6 See Diagram 6 A Securely tighten all Nuts and Bolts previously installed B Attach the Right Seat Support 10 to the Right Base Frame 1 Secure it with one M10 x 2 12 Carriage Bolt 98 Ya Washer 21 and M10 Aircraft Nut 18 C Attach the Right Seat Support 10 to the Right Vertical Frame 5 Secure it with two M10 x 2 Carriage Bolts 98 one 4 3 8 x 1 37 Bracket 84 two Y 34 Washers 21 and two M10 Aircraft Nuts 18 D Attach the Leg Developer 26 to the bracket on the Right Seat Support Secure it with a M10 x 2 7 8 Allen Bolt 92 two Y 34 Washers 21 and one M10 Aircraft Nut 18 Do not over tighten the Nut and Bolt Make sure the Leg Developer is able to swivel E Attach the Butterfly Support Fra
11. me 12 and the Butterfly Pulley Support 46 to the Right Vertical Frame Align the holes and secure them together with two M10 x 2 7 Carriage Bolts 98 Ya Washers 21 and M10 Aircraft Nuts 18 F Attach two Swivel Pulley Brackets 49 to the Butterfly Pulley Support 46 Secure each Bracket with one M12 x 4 3 8 Hex Bolt 99 two Y 1 Washers 22 and one M12 Aircraft Nut 19 Do not over tighten the Nut and Bolt Make sure each Bracket is able to swivel 12 DIAGRAM 6 Sy amp u 5 E XR ies NG OF YA 2 a AO YA Quay Cy gt CNN W A PAS STEP 7 See Diagram 7 A Attach the Left Seat Support 11 to the Left Base Frame 2 Secure it with one M10 2 V Carriage Bolt 98 34 Washer 21 and M10 Aircraft Nut 18 B Attach the Left Seat Support 11 to the Left Vertical Frame 6 Secure it with two M10 x 2 7 Carriage Bolts 98 one 4 3 8 x 1 34 Bracket 84 two Y 34 Washers 21 and two M10 Aircraft Nuts 18 C Attach the Leg Press Frame 25 to the bracket on the Left Base Frame Secure it with one M12 x 3 Hex Bolt 100 two Y 1 Washers 22 and one M12 Aircraft Nut 19 DO not over tighten the Nut and Bolt Make sure the Leg Press Frame is able to swivel D Attach the Leg Press Plate 52 to the Leg Press Adjustment Frame 47 Secure it with one M10 x 2 Y Carriage Bolt 98 34 Washer 21 an
12. ng exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly CARE AND MAINTENANCE 1 Lubricate moving parts with WD 40 or light oil periodically 2 Inspect and tighten all parts before using the machine 3 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents 4 Maximum user s weight 300 lbs WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL REPLACEMENT AA en Ne EEN 7 Venen eg ES missing or illegible please call customer service at 1 800 888 8899 for replacements Apply the labels The warning labels shown here have been placed on the Rear Base and Upper Frame If the labels are in location shown HARDWARE PACK 90 Long Chain Qty 1 3 897 M10 x 2 3 4 Carriage Bolt Qty 4 um 98 M10 x 2 1 2 Carriage Bolt Qty 23 95 M10 x 1 3 4 Allen Bolt Qty 18 Lo 894 M10 x 1 Allen Bolt Qty 13 93 M10 x 5 8 Allen Bolt Qty 10 9 10 11 12 13 14 15 HARDWARE PACK 99 M12 x 4 3 8 Hex Bolt Qt
13. ordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time www impex fitness com info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase PONS 31
14. ot then to the open Swivel Pulley Bracket 49 B Attach a Pulley 64 to the bracket Secure it with one M10 x 1 34 Allen Bolt 95 two Ya Washers 21 and one M10 Aircraft Nut 18 C Draw the Cable around the Pulley then downward Install a Pulley to an Angled Floating Pulley Bracket 31 Let the Bracket hanging for now D Draw the Cable upward to the right Swivel Pulley Bracket on the opposite side Install another Pulley E Draw the Cable to the Right Butterfly Adjustment Frame and clip the end of the cable to the slot DIAGRAM 11 20 STEP 12 See Cable Loop Diagram amp Diagram 12 A Attach the 146 Lower Cable 35 to the lower opening on the Leg Developer 26 Attach a Pulley 64 to the opening Secure it with one M10 x 2 3 8 Allen Bolt 96 two Pulley Bushings 63 and one M10 Aircraft Nut 18 B Draw the Cable underneath the Pulley to the opening on the bottom of Right Seat Support 10 Attach a Pulley to the opening and secure it with one M10 x 2 3 8 Allen Bolt 96 two Pulley Bushings 63 and one M10 Aircraft Nut 18 C Draw the Cable underneath the Pulley then through the bottom opening on the Right Vertical Frame 5 to the second open bracket on the Right Base Frame 1 D Attach a Pulley to the second open bracket Secure it with one M10 x 1 9 Allen Bolt 95 two 34 Washers 21 and one M10 Aircraft Nut 18 E Draw the Cable around the Pulley then
15. r Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the same station 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretchi
16. rt Butterfly Support Frame Foam Tube Left Butterfly Right Butterfly Front Press M6 5 8 Philips Screw 10 Aircraft Nut 12 Aircraft Nut 5 8 Washer Washer 1 Washer Vertical Press Base Vertical Press Arm Leg Press Frame Leg Developer Seat Incline Adjustment Frame Single Handle Front Press Base Weight Stack Cover Angled Floating Pulley Bracket Double Floating Pulley Bracket Lock Ring 1 34 Rubber Bumper 146 Lower Cable 102 Upper Cable 76 Butterfly Cable 49 Front Press Cable 94 Vertical Press Cable 216 Leg Press Cable Backrest Board Seat Arm Pad Manual Left Seat Support End Cap Butterfly Pulley Support Leg Press Adjustment Frame Lat Bar Swivel Pulley Bracket Butterfly Adjustment Frame Q1 12 x 7 8 Bushing Leg Press Plate Selector Rod Weight Plate Selector Stem o lt o Bn HAH KH yNNnNnnapa A dd HNP dp 29 Arm Curl Handle Arm Curl Handle Bar Vinyl Foam Roll Axle L shaped Cable Retainer 2 Square End Cap Weight Selector Pin Pulley Bushing Pulley Small Pulley T shaped Pull Pin 2 x 1 34 Sleeve Lock Knob Foam Roll End Cap 2 x 1 End Cap 1 Square End Cap Ankle Strap 1 2 Square End Cap 1 Y4 Square End Cap 2 Cone shaped End Cap 6 Handle Grip 17 Vertical Press Handle Grip 6 Allen Wrench Tool 5 Allen Wrench Tool 1 Ye x 1 Bushing
17. s from both ends Plug four Foam Roll End Caps 69 into the ends C Connect the Arm Curl Handle 56 to the 146 Lower Cable 35 with one Long Chain 90 and two C clips 89 D Connect the Lat Bar 48 to the 102 Upper Cable 36 with one Short Chain 88 and two C clips 89 E Cover the Weight Plates with four Weight Stack Covers 30 Secure each Weight Stack Cover with two M10 x 5 8 Allen Bolts 93 and 32 Washers 21 Y EA X IS y amp X 27 STEP 17 See Diagram 17 Attach the Backrest Board 41 to the Right 8 Left Vertical Frames 5 8 6 Secure each Board with two M8 x 2 2 Allen Bolts 101 and 5 8 Washers 20 B Place the Seat 42 onto the Right Seat Support 10 Secure it with two M8 x 2 7 Allen Bolts 101 and Y 5 8 Washers 20 Attach four Arm Pads 43 to the Right and Left Butterfly 15 amp 14 Secure each Arm Pad with two M8 x 2 12 Allen Bolts 101 and Y 5 8 Washers 20 D To maximize the performance of the gym it is recommended to use light lubricant such as WD 40 on the four chrome Guide Rods which the weight plates slide up and down on to minimize friction DIAGRAM 17 PARTS LIST KEY DESCRIPTION Right Base Frame Left Base Frame Rear Base Frame Guide Rod Right Vertical Frame Left Vertical Frame Rear Vertical Frame Upper Frame Top Socket Assembly Right Seat Support Left Seat Suppo
18. y 2 100 M12 x 3 Hex Bolt Qty 1 101 M8 x 2 1 2 Allen Bolt Qty 10 mm 102 M8 x 1 5 8 Allen Bolt Qty 2 9 d 818 MIO Aircraft Nut 819 M12 Aircraft Nut Qty 60 Qty 3 22 9 1 Washer 21 9 3 4 Washer 20 9 5 8 Washer Qty 6 Qty 94 Qty 12 mm 012 3 4 5 6 7 8 9 10 11 12 13 14 15 MP 5 HARDWARE PACK U 33 Lock Ring Qty 2 63 Pulley Bushing Qty 8 59 Axle Qty 2 CSS SS 88 Short Chain Qty 2 O mm C 92 M10 x 2 7 8 Allen Bolt Qty 1 89 C clip Qty 5 10 11 12 13 14 15 ASSEMBLY INSTRUCTION Tools Reguired Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended two or people assembling this machine to avoid possible injury STEP1 See Diagram 1 A Place the Right Base Frame 1 on a flat surface Make sure there is enough space around to assemble the machine B Insert four Guide Rods 4 into the holes on the Right Base Frame Secure each Guide Rod from the bottom with a M10 x 1 Allen Bolt 94 C Slide four 2 1 2 x 1 Rubber Bumpers 86 onto the Guide Rods DIAGRAM 1 STEP 2 See Diagram 2 A Attach the Left Base and the Rear Base Frame 2 8 43 to the Right Base Frame 1 B Align the holes and secure them with two M10 x 2 Carriage Bolts 98 34 Washers 21 and M10 Aircraft Nuts 18 DIAGRAM 2 STEP 3 See Diagram 3
Download Pdf Manuals
Related Search