Impex MWB-36780B Owner's Manual
Contents
1. 48 j Large Washer Qty 2 437 M10 x 5 J Allen Bolt Qty 2 42 ST5 Screw Qty 2 35 M8 x j Allen Bolt Qty 6 41 3 Washer Qty 8 40 j Washer Qty 8 39 j Washer Qty 10 ET imi 43 M10 Aircraft Nut 44 M8 Aircraft Nut 51 M10 Hex Nut Qty 6 Qty 1 Qty 2 h 1 2 3 4 5 6 T 8 9 biblia lo i zr id Ld 5 6 ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended that two or more people assemble this machine to avoid possible injury STEP 1 See Diagram 1 A Bench should be placed on flat surface The incline or decline of surface should be limited to a 3 or less for best performance and safety B Do not tighten Nuts and Bolts until instructed to do so C Install the two Upright End Caps 17 onto the bottom of the Right amp Left Upright Beams 1 amp 2 Secure each Cap with a ST5 Screw 42 D Connect the two Upright Beams by a Cross Brace 4 in the Mid span Secure them with two M10 x 3 1 8 Carriage Bolts 33 one Curved Bracket 12 two 34 Washers 39 and two M10 Aircraft Nuts 43 on each end of the Cross Brace E Place the Backrest Adjustment Bar 32 onto the selected slots on the Upright Beams to obtain desired incline for the Backrest DIAGRAM 1 STEP 2 See Diagram 2 A Do not2. 13 2DRwWLoOoNRLBOLBLBLBlRNONMBRMBROLA UNM v v o oaloalnlo o VNYUYVYNAAAHANBDO IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights for products return to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or lim
3. Clip 19 to each end of the Bar to hold the plates in position D Place the Weight Bar 14 onto the Left amp Right Upright Beam 2 amp 1 E When unloading weight plates Weight plates on the Bar must be taken off in equal amounts at the same time to prevent the bar being unevenly weighted which will cause the Bar to tip It is strongly recommended always move the Bar from Uprights to ground when loading and unloading Weight Plates DIAGRAM 7 11 PARTS LIST KEY NO DESCRIPTION QUANTITY Right Upright Beam Left Upright Beam Main Seat Support Cross Brace Front Leg Arm Curl Stand Leg Developer Butterfly Main Seat Stabilizer Backrest Support Foam Tube Curved Bracket Butterfly Handle Weight Bar 1 Square End Cap 1 End Cap Upright End Cap 34 Bushing Spring Clip Front Leg End Cap 2 3 8 x 2 Sleeve 2 End Cap 134 End Cap 1 1 8 End Cap 1 Bushing 25lb Weight Plate 15lb Weight Plate Foam Roll Arm Curl Pad Seat Pad Backrest Board Backrest Adjustment Bar M10 x 3 1 8 Carriage Bolt M10 x 2 3 8 Carriage Bolt M8 x 5 8 Allen Bolt M8 x 3 1 8 Allen Bolt M10 x 5 7 8 Hex Bolt M6 x 1 3 8 Hex Bolt 4 Washer 5 8 Washer 12 Washer ST5 Screw M10 Aircraft Nut M8 Aircraft Nut M10 x 2 5 8 Lock Knob M6 x 1 1 2 Hex Bolt M10 x 5 8 Allen Bolt 34 Large Washer Butterfly Grip M10 Butterfly Lock Knob M10 Hex Nut
4. However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands and feet away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is recommended during exercise CARE AND MAINTENANCE Lubricate moving parts w
5. tighten Nuts and Bolts until instructed to do so B Install a Front Leg End Cap 20 onto the bottom of Front Leg 5 Attach the Front Leg to the Main Seat Support 3 Secure it with three M8 x 5 8 Allen Bolts 35 and three 5 8 Washers 40 C Attach the Main Seat Support 3 to the Cross Brace 4 Attach the Main Seat Stabilizer 9 to the Main Seat Support Align the holes Secure the Main Seat Support Main Stabilizer and Cross Brace together with two M10 x 2 3 8 Carriage Bolts 34 two 34 Washers 39 and two M10 Aircraft Nuts 43 D Attach the other end of Main Seat Stabilizer 9 to the Front Leg 5 Secure it with one M8 x 5 8 Allen Bolt 35 and 5 8 Washer 40 E Securely tighten all Nuts and Bolts previously installed DIAGRAM 2 STEP 3 See Diagram 3 A Attach the Leg Developer 7 to the Front Leg 5 Secure it with one M8 x 3 1 8 Allen Bolt 36 two 5 8 Washers 40 and one M8 Aircraft Nut 44 B Insert two Foam Tubes 11 halfway through the holes on the Leg Developer Push four Foam Rolls 28 onto the Tubes from both sides C Attach a Spring Clip 19 to the weight post on Leg Developer DIAGRAM 3 STEP 4 See Diagram 4 A Attach the Backrest Supports 10 onto both ends of the pivot on the Main Seat Support 3 Place the other end rest against the Backrest Adjustment Bar 32 B Place the Backrest Board 31 onto the Back
6. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MWB 36780B Retain This Manual for Reference 110624 OWNER S MANUAL VIP EX MARCY BENCH W S0LB WEIGHT SET MWB 36780B IMPEX INC 2801 S Towne Ave Pomona CA 91766 Tel 800 999 8899 Fax 626 961 9966 www impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN IMPORTANT SAFETY NOTICE HARDWARE IDENTIFIER ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM PARTS LIST WARRANTY ORDERING PARTS BEFORE YOU BEGIN Thank you for selecting the MARCY MWB 36780B Bench w 80lb weight set by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST www impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety
7. itation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line www impex fitness com IMPEX INC 2801 S Towne Ave Pomona CA 91766 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase Desa dad 14
8. ith WD 40 or light oil periodically Inspect and tighten all parts before using the machine The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents 4 Maximum weight capacity on the uprights 200 Ibs 5 Maximum user s weight 300 Ibs 6 7 ons Maximum weight capacity on the leg developer 100 Ibs Assembled Dimension 65 x 54 x 50 WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace If the label is missing or illegible please call customer service at 1 800 999 8899 for replacement Apply the label in location shown HARDWARE IDENTIFIER NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 0 33 M10 x 3 j Carriage Bolt Qty 4 Imm m 434 M10 x 2 j Carriage Bolt Qty 2 amp mm 36 M8 x 3 Jj Allen Bolt Qty 1 B uum 47 M10 x j Allen Bolt Qty 2 38 M6 x 1j Hex Bolt Qty 4 HL Han 46 M6 x 1j Hex Bolt Qty 4
9. rest Supports Secure it with four M6 x 1 1 2 Hex Bolts 46 and 7 Washers 41 C Place the Seat Pad 30 onto the Main Seat Support Secure it with four M6 x 1 3 8 Hex Bolts 38 and 1 Washers 41 DIAGRAM 4 STEP 5 See Diagram 5 A Attach the Arm Curl Pad 29 to the Arm Curl Stand 6 Secure it with two M8 x 5 8 Allen Bolts 35 and 5 8 Washers 40 B Insert the Arm Curl Stand into the top opening on the Front Leg Secure it with a M10 x 2 5 8 Lock Knob 45 C When using Leg Developer remove the Arm Curl Stand from the Front Leg DIAGRAM 5 STEP 6 See Diagram 6 A Attach one Butterfly 8 to the pivot on Left Upright Beam 2 Secure it with one M10 x 5 7 8 Hex Bolt 37 two 34 Washers 39 one M10 Hex Nut 51 and one M10 Butterfly Lock Knob 50 Do not over tighten the Knob Make sure the Butterfly is able to move freely B Insert a Butterfly Handle 13 through the opening on the Butterfly arm from front Secure the Handle with one M10 x 5 8 Allen Bolt 47 and one 4 Large Washer 48 Attach a Spring Clip 19 to the weight post on the Butterfly C Repeat Procedure A and B to install the other Butterfly to Right Upright Beam 1 DIAGRAM 6 10 STEP 7 See Diagram 7 A Load 25 lbs two Weight Plates 26 onto each end of the Bar B Load 15 Ibs two Weight Plates 27 onto each end of the Bar C Attach a Spring
Download Pdf Manuals
Related Search