Impex MWB-2001 Owner's Manual
Contents
1. IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lie2. recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do stretching exercises to properly warm up Never operate the machine if the machine is not functioning properly A spotter is recommended during exercise WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS HARDWARE PACK 28 5 3 4 L shaped Pin Qty 2 60 4 L shaped Pin Qty 1 31 3 L shaped Pin P 35 Spring Clip Qty 3 52 M10 x 5 8 Allen Bolt Qty 13 54 M8 x 5 8 Allen Bolt Qty 6 36 Axle Qty 1 mm 09123 4 5 67 8 9 101112131415 HARDWARE PACK 49 M10 x 4 3 4 Carriage Bolt Qty 8 50 M10 x 2 3 4 Carriage Bolt Qty 4 51 M10 x 2 1 2 Carriage Bolt Qty 1 WM 53 M10 x 4 3 4 Allen Bolt Qty 1 a 855 M8 x 1 5 8 Allen Bolt Qty 4 58 M10 Aircraft Nut Qty 14 56 Washer Qty 30 57 Washer Qty 10 mm 92234685 6 8 9 101112131415 ASSEMBLY IN
3. to the pivot on the Sliding Block Secure it with one M10 x 4 3 Allen Bolt 53 two 34 Washers 56 and one M10 Aircraft Nut 58 C Place the Seat 22 onto the Seat Bracket Secure it with four M8 x 5 8 Allen Bolts 54 and 5 8 Washers 57 D Insert a 4 L shaped Pin 60 into the selected hole on the Seat Bracket to obtain the desired Seat inclined position DIAGRAM 3 7 STEP 4 See Diagram 4 A Attach the Leg Developer 11 to the Leg Developer Holder 9 Secure it with an Axle 36 two M10 x 5 8 Allen Bolts 52 and two 3 4 Washers 56 B Insert one Foam Tube 24 halfway through the hole on the Leg Developer Holder Insert two Foam Tubes halfway through the holes on the Leg Developer Push six Foam Rolls 30 onto the Tubes from both ends Plug six Foam Roll End Caps 38 into the ends C Slide an Olympic Sleeve 34 onto the weight post on the Leg Developer Attach a Spring Clip 35 to the Sleeve DIAGRAM 4 STEP 5 See Diagram 5 A Attach the Arm Curl Pad 63 to the Arm Curl Stand 10 Secure it with two M8 x 5 8 Allen Bolts 54 and 2 5 8 Washers 57 B Insert the Arm Curl Stand into the top opening on the Leg Developer Holder Use a M18 x Lock Knob 33 to secure the Stand C Attach the Curl Bar Handle Frame 18 to the bracket on the Leg Developer 11 Secure it with a 3 L shaped Pin 81 D Remove the Arm C
4. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model AX 2001 Retain This Manual for Reference 04 05 05 OWNER S MANUAL OLYMPIC BENCH MWB 2001 IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN scwcd ite a a E a 1 IMPORTANT SAFETY NOTICE Ss AAE 2 HARDWARE 3 ASSEMBLY 61 1 2 911 10 2189 5 EXPLODED DIAGRAM erronea E 10 WARRANTY AAAA A AA N E A a aE 12 ORDERING PART he lcd 5 arie eera a 12 BEFORE YOU BEGIN Thank you for selecting the MARCY MWB 2001 OLYMPIC BENCH by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you com
5. STRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended this machine to be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1 A Attach the Right Upright Beam 1 to a Rear Stabilizer 3 Secure it with two M10 x 4 Carriage Bolts 49 one 5 x 2 Bracket 29 two 34 Washers 56 and two M10 Aircraft Nuts 58 Do not tighten the Nut and Bolts yet B Attach the bottom of the Dumbbell Rack 4 to the Rear Stabilizer 3 Secure it with two M10 x 5 8 Allen Bolts 52 and 3 4 Washers 56 C Attach the top of the Dumbbell Rack to the Right Upright Beam 1 Secure it with two M10 x 5 8 Allen Bolts 52 and 34 Washers 56 D Repeat Steps A B and C above to install the Left side E Connect the Left amp Right Upright Beams with a Cross Brace 5 in the mid span Secure each end with two M10 x 4 34 Carriage Bolts 49 one 5 1 x 2 Bracket 29 two Washers 56 and two M10 Aircraft Nuts 58 Securely tighten all Nuts and Bolts F Place the Backrest Adjustment Bar 12 onto the selected slot between the Upright Beams DIAGRAM 1 STEP 2 See Diagram 2 A Slide the Sliding Block 7 onto the Main Seat Support 6 Thread a M18 x 3 8 Lock Knob 32 into the selected hole to hold the Sliding Block in position B Attach the Leg Developer Holde
6. plete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOOL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 10 11 12 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not
7. r 9 to the Front Stabilizer 25 Secure it with three M10 x 5 8 Allen Bolts 52 and 3 4 Washers 56 C Attach the Main Seat Support 6 to the Leg Developer Holder Secure it with one M10 x 2 V2 Carriage Bolt 51 from the top two M10 x 2 Carriage Bolts 50 from the side three Washers 56 and three M10 Aircraft Nuts 58 D Attach the Main Seat Support 6 to the Cross Brace 5 Secure it with two M10 x 2 34 Carriage Bolts 50 one 5 x 2 3 Bracket 27 two 3 4 Washers 56 and two M10 Aircraft Nuts 58 E Attach the two Squat Bar Catches 13 to the back of the two Upright Beams Secure each Catch with a 5 34 L shaped Pin 28 F Insert a Weight Post 19 into the side hole on the Upright Beam Secure it with one M10 x 54 Allen Bolt 59 and Washer 56 Slide an Olympic Sleeve 34 onto the Weight Post Attach a Spring Clip 35 to the Sleeve Repeat for the other side G Insert the Right amp Left Bar Catches 14 amp 15 Right amp Left Safety Catch 16 amp 17 into the selected holes on the Upright Beams 1 amp 2 DIAGRAM 2 STEP 3 See Diagram 3 A Attach the holes on the end of the Backrest Supports 20 to the pivot on the Sliding Block 7 Attach the Backrest Board 21 to the Backrest Supports Secure it with four M8 x 1 5 8 Allen Bolts 55 and 5 8 Washers 57 B Attach the Seat Bracket 8
8. u of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase 65 3 gt 12
9. url Stand and the Curl Bar Handle when using the Leg Developer DIAGRAM 5 EXPLODED DIAGRAM PARTS LIST KEY NO DESCRIPTION OONOARWND Right Upright Beam Left Upright Beam Rear Stabilizer Dumbbell Rack Cross Brace Main Seat Support Sliding Block Seat Bracket Leg Developer Holder Arm Curl Stand Leg Developer Backrest Adjustment Bar Squat Bar Catch Left Bar Catch Right Bar Catch Right Safety Catch Left Safety Catch Curl Bar Handle Frame Weight Post Backrest Support Backrest Board Seat Chrome Panel Foam Tube Front Stabilizer Curl Bar Handle 5 V2 x 2 Bracket 5 52 L shaped Pin 5 2 x 2 Bracket Foam Roll 3 L shaped Pin M18 x 34 Lock Knob M18 x 1 1 8 Lock Knob Olympic Sleeve Spring Clip Axle 2 3 8 x 1 Sleeve Foam Roll End Cap 1 End Cap 2 1 Cone Shaped End Cap 1 Square End Cap 4 x 2 End Cap 2 3 8 Square End Cap 1 5 8 x 2 3 8 End Cap 1 2 Bushing 2 3 8 Bushing 57 Bushing Curl Bar Handle Grip M10 x 4 34 Carriage Bolt M10 x 2 Carriage Bolt lt 11 M10 x 2 Carriage Bolt M10 x 5 8 Allen Bolt M10 x 434 Allen Bolt M8 x 5 8 Allen Bolt M8 x 1 5 8 Allen Bolt 5 Washer 5 8 Washer M10 Aircraft Nut M10 x amp Allen Bolt 4 L shaped Pin Rubber Bumper Chrome Panel Screw Arm Curl Pad 2 3 8 x 2 Sleeve IMPEX INC LIMITED WARRANTY IMPEX Inc
Download Pdf Manuals
Related Search