Impex MSS-1280 User's Manual
Contents
1. Make sure the Backrest Supports are able to swivel DIAGRAM 3 21 STEP 4 See Diagram 4 A Attach the Backrest Board 13 to the Backrest Supports 3 Secure it with four M8 x 1 5 8 Allen Bolts 34 and four Y 5 8 Washers 30 B Attach the Seat Pad 12 to Front amp Rear Seat Bracket 4 amp 5 Secure them with four M8 x 1 5 8 Allen Bolts 34 and four Y 5 8 Washers 30 C Pull up the Backrest Adjustment Support 8 or press down the Backrest Adjustment Lever 9 to adjust the Backrest incline position DIAGRAM 4 22 STEP 5 See Diagram 5 A Attach the Leg Developer 2 to Main Seat Support 1 Secure it with one M10 x 3 1 8 Allen Bolt 38 two 34 Washers 31 and one M10 Aircraft Nut 33 B Insert two Foam Tubes 10 halfway through the holes on Leg Developer Push four Foam Rolls 16 onto the Tubes from both ends Plug four Foam Roll End Caps 17 into the ends C Slide an Olympic Sleeve 28 on the weight post on Leg Developer Attach a Spring Clip 27 to the Sleeve DIAGRAM 5 23 BENCH EXPLODED DIAGRAM BENCH PARTS LIST KEY NO DESCRIPTION Main Seat Support Leg Developer Backrest Support Front Seat Bracket Rear Seat Bracket Bench Base Frame Rear Stabilizer Backrest Adjustment Support Backrest Adjustment Lever 10 Foam Tube 11 Spring 12 Seat Pad 13 Backrest Board 14 2 34 Grip 15 2 x 1 5 8 Rubber Bumper 16 Foam Roll2. to the lower hole G Slide Lower Left Safety Stop Frame 9 onto a Guide Rod 11 Slide one Safety Stop Frame 18 onto the Guide Rod Insert the bottom of the Guide Rod into the hole on the left Base Frame Attach the top of the Guide Rod to the bracket on Left Upright Beam Secure each end of Guide Rod with one M10 x 34 56 and one Y Washer 57 Repeat the same step to install the Lower Right Safety Stop Frame 10 the other Safety Stop Frame and the other Guide Rod to the other side H Turn and attach the hooks on the Lower Left amp Right Safety Stop Frame to the selected slot on Left amp Right Upright Beam 1 amp 2 DIAGRAM 2 STEP 3 See Diagram 3 A Attach two 2 3 8 x 2 Rubber Bumpers 30 to the holes on the Cross Brace 7 Insert the two Rear Short Guide Rods 17 through the two Rubber Bumpers into the holes on Cross Brace B Secure each Guide Rod to the Cross Brace with one M10 x 34 Allen Bolt 56 and one Y 34 Washer 57 from bottom C Slide the Sliding Weight Post 16 onto the two Rear Short Guide Rods Make sure the Pulley bracket on the Weight Sliding Frame faces upward D Attach the Rear Upper Frame 15 to the two Rear Short Guide Rods Secure each Guide Rod to the Rear Upper Frame with one M10 x 9 Allen Bolt 56 and one Y 34 Washer 57 E Attach the front of Rear Upper Frame to the Top Beam 4 Attach the Front Upper Frame 14 to the Top Beam fro
3. 2 2 20DPODOUI DO R DDDARD DNDDD D DD ch hc ch PD ch ch AAA AHA A ty 16 M10 x 1 Allen Bolt M10 x 1 3 Allen Bolt M10 x 4 1 8 Allen Bolt M10 x 4 Allen Bolt M10 x 3 1 Allen Bolt M10 x 34 Allen Bolt Y Washer M10 Aircraft Nut ST3 8 Philips Screw Rivet M8 x 3 8 Allen Bolt Spring Clip M10 x 5 8 Allen Bolt 7 8 x 34 End Cap 5 8 End Cap 34 End Cap BENCH HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 34 M8 x 1 M Allen Bolt Qty 12 I 35 M8 x 5 i Allen Bolt Qty 1 m 36 M10 x 2 Allen Bolt Qty 1 J qam 38 M10 x 3 i Allen Bolt Qty 1 To mm 40 M10 x 4 Allen Bolt Qty 2 1 qul 39 M10 x 6 i Allen Bolt Qty 1 2 sf amp 6 7 8 Y 10 ff 12 15 14 TE 17 BENCH HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 41 M10 x 4 Carriage Bolt Qty 5 27 Spring Clip Qty 1 31 Y i Washer 30 Y 3 Washer Qty 14 Qty 18 EZE oD 33 M10 Aircraft Nut 32 M8 Aircraft Nut Qty 9 Qty 5 01 2 5 4 5 6 7 8 9 10 11 12 13 14 15 18 BENCH ASSEMBLY INSTRUCTION STEP 1 See Diagram 1 A Attach the Bench Base Frame 6 to the Rear Stabilizer 7 Secure the side holes with two M10 x 4 Carriage Bolts 41 two 9 Washers 31 and two M10 Aircraft Nuts 33 Secure the top hole w
4. 17 Foam Roll End Cap 18 1 5 8 x 3 1 8 End Cap 19 1 Square End Cap 20 1 End Cap 21 2 End Cap 22 Base Frame End Cap 23 Rear Stabilizer Left End Cap 24 Rear Stabilizer Right End Cap 25 Wheel Set 26 Lever Cover 27 Spring Clip 28 Olympic Sleeve 29 Y4 Leg Developer Bushing 30 5 8 Washer 31 34 Washer 32 M8 Aircraft Nut 33 M10 Aircraft Nut 34 M8 x 1 5 8 Allen Bolt 35 M8 x 5 1 8 Allen Bolt 36 M10 x 5 8 Allen Bolt 37 M10 x 2 Allen Bolt 38 M10 x 3 1 8 Allen Bolt 39 M10 x 6 Y Allen Bolt 40 M10 x 4 Allen Bolt 41 M10 x 4 Carriage Bolt OO JO Om PS Go 25 IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products
5. If the labels are missing or illegible please call customer service at 1 800 888 8899 for replacements Apply the labels in the location shown SMITH MACHINE HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 63 M10 x CH Allen Bolt Qty 2 m 56 M10 x 3 Allen Bolt Qty 12 am 51 M10 x 1 Allen Bolt Oty 1 36 Hook Oty 5 d mm 452 M10 x 1 j Allen Bolt Qty 2 58 M10 Aircraft Nut 8 Hun Qty 28 55 M10 x 3 3 Allen Bolt Qty 4 O Ho mm 54 M10 x 4 Allen Bolt Qty 7 57 Y i Washer Qty 58 53 M10 x 4 i Allen Bolt Qty 2 mm D123 4 5 6 7 8 9 10 11 12 13 14 15 CAGE MACHINE HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size GT 43 10 link Chain Qty 1 42 15 link Chain Qty 1 CSS 44 5 link Chain Qty 1 62 Spring Clip Qty 8 NA 50 M10 x 2 n Carriage Bolt Qty 8 III lli 49 M10 x 4 i Carriage Bolt Qty 2 mm 2 3 4 5 6 7 8 9 10 11 12 13 14 18 SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended that two or more people assemble this machine to avoid possible injury STEP 1 See Diagram 1 A Note Do not tighten the Nuts and Bolts until instructed to do so B Connect the two Base Frames 3 by
6. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MSS 1280 Retain This Manual for Reference 08 03 09 OWNER S MANUAL saQcear DELUXE SMITH MACHINE MSS 1280 E AS t p I l y A d auf IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN cosas rated 1 IMPORTANT SAFETY NOTIGES a a a ana 2 SMITH MACHINE HARDWARE PACK AE 4 SMITH MACHINE ASSEMBLY INSTRUCTIONS eeeeene 6 SMITH MACHINE EXPLODED DIAGPRAM eene 15 SMITH MACHINE PARTS EIST a a eri ae 16 BENCH HARDWARE PACK oa een 17 BENCH ASSEMBLY INSTRUCTION AAA 19 BENCH EXPLODED DIAGRAM utr th rrr ben Ripe bx ad taxi Rn Rad raa aa 24 BENGELUPAFTSSBIS Tz stasera led Ae eut sube a p datu cel 25 WARRANTY S atn t ide ion eb SN see 26 ORDERING PARTS eere en eot etna eph net eph ara rao epa aaa nV MR aene 26 BEFORE YOU BEGIN Thank you for selecting the SA GEAR DELUXE SMITH MACHINE MSS 1280 IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you comple
7. ing replacement parts always give the following information Model Description of Parts Part Number Date of Purchase AUH 26
8. ith one M10 x 5 8 Allen Bolt 36 and one 34 Washer 31 B Attach the Wheel Set 25 to the bracket on Rear Stabilizer Secure it with one M8 x 5 1 8 Allen Bolt 35 two 5 8 Washers 30 and one M8 Aircraft Nut 32 DIAGRAM 1 19 STEP 2 See Diagram 2 A Attach the Main Seat Support 1 to the Bench Base Frame 6 Secure it with three M10 x 4 Carriage Bolts 41 three Y 37 Washers 31 and three M10 Aircraft Nuts 33 B Attach the Front amp Rear Seat Bracket 4 amp 5 to Main Seat Support Secure each Bracket with one M10 x 4 Allen Bolt 40 two 37 Washers 31 and one M10 Aircraft Nut 33 DIAGRAM 2 20 STEP 3 See Diagram 3 A Align the bracket on the Backrest Adjustment Support 8 in between the two Backrest Supports 3 Secure it with four M8 x 1 5 8 Allen Bolts 34 eight 5 8 Washers 30 and four M8 Aircraft Nuts 32 Do not tighten the Nuts and Bolts yet B Insert the Backrest Adjustment Support into the opening on the Main Seat Support 1 Press or step down on the Backrest Adjustment Lever 9 to allow the Support to go through C Attach the bottom side holes on the two Backrest Supports to the pivot on the Main Seat Support Secure it with one M10 x 6 1 2 Allen Bolt 39 two Y 32 Washers 31 and one M10 Aircraft Nut 33 D Securely tighten all Nuts and Bolts in B amp C E Do not over tighten the Nut and Bolt in C F
9. le 26 to the open bracket on the Cross Brace 7 Attach a Pulley 33 to the bracket Secure it with one M10 x 1 37 Allen Bolt 52 two Y 34 Washers 57 one L shaped Cable Retainer 24 and one M10 Aircraft Nut 58 B Draw the Cable underneath the Pulley then upward to the 170 Upper Cable 25 installed in Step 4 C Connect the Lower Cable to a Hook 36 Connect the Hook to the 5 link Chain 44 Secure the 5 link Chain to the end of Upper Cable with one M10 x 1 Allen Bolt 51 two 34 Washers 57 and one M10 Aircraft Nut 58 Adjust the tension of the Cable system by moving the Hook position to the Chain If the tension is too loose then move the hook up the chain If the tension is too tight then move down the Hook D Connect the Shiver Bar 21 to the ball stopper on Lower Cable with two Hooks 36 and one 15 link Chain 42 WE STEP 6 See Diagram 6 A Place the Lifting Sleeve 8 in between the two Safety Stop Frames 18 Align the holes Insert the Weight Bar 13 from outside of one Safety Stop Frame through the Lifting Sleeve to the other Safety Stop Frame on the other side B Turn and attach the two safety catch hooks on the Lifting Sleeve 8 to the selected slots on the Left and Right Uptight Beams 1 amp 2 C Attach two Weight Bar Sleeves 35 onto the Weight Bar from both ends Attach two Spring Clips 62 to the Sleeves D Attach four Weight Posts 12 int
10. m front Align the holes Secure them together with two M10 x 2 34 Carriage Bolts 47 two 34 Washers 57 and two M10 Aircraft Nuts 58 F Securely tighten all Nuts and Bolts installed in Step 1 Step 2 and Step 3 DIAGRAM 3 10 CABLE LOOP DIAGRAM STEP 4 See Diagram 4 amp Cable Loop Diagram A Attach the 170 Upper Cable 25 to the opening on the Front Upper Frame 14 B Attach a Pulley 33 to the opening Secure it with one M10 x 4 Allen Bolt 54 two 34 Washers 57 and one M10 Aircraft Nut 58 C Draw the Cable over the Pulley toward the back of the machine Note The Ball stopper on the Cable needs to be under the Frame D Draw the Cable to the first opening on the Rear Upper Frame Repeat B to install a Pulley E Draw the Cable around the Pulley then downward to the open Pulley bracket on the Sliding Weight Post 16 F Attach a Small Pulley 32 to the bracket Secure it with one M10 x 1 37 Allen Bolt 52 two 34 Washers 57 and one M10 Aircraft Nut 58 G Draw the Cable around the Pulley then upward to the rear opening on the Rear Upper Frame Repeat B to install a Pulley H Draw the Cable around the Pulley and let the Cable hanging just for now Connect the Lat Bar 21 to the ball stopper on the Cable with two Hooks 36 and one 10 link Chain 43 x 12 STEP 5 See Diagram 5 amp Cable Loop Diagram A Attach the 62 Lower Cab
11. o the holes on Left amp Right Rear Support 5 amp 6 Secure each Weight Post to the Support with one M10 x 34 Allen Bolt 56 and one Y 34 Washer 57 Slide four Olympic Sleeves 34 to the four Weight Posts Attach four Spring Clips to the Sleeves 14 SMITH MACHINE EXPLODED DIAGRAM 15 SMITH MACHINE PART LIST KEY NO DESCRIPTION 1 Left Upright Beam 2 Right Upright Beam 3 Base Frame 4 Top Beam 5 Left Rear Support 6 Right Rear Support 7 Cross Brace 8 Lifting Sleeve 9 Lower Left Safety Stop Frame 10 Lower Right Safety Stop Frame 11 Guide Rod 12 Weight Post 13 Weight Bar 14 Front Upper Frame 15 Rear Upper Frame 16 Sliding Weight Post 17 Rear Short Guide Rod 18 Safety Stop Frame 19 Lat Bar 20 Shiver Bar 21 Rotate Ring 22 4 34 x 3 Va Bracket 23 4 x 2 3 8 Curved Bracket 24 L shaped Cable Retainer 25 170 Upper Cable 26 62 Lower Cable 27 3 ve Upright Beam End Cap 28 1 5 8 x 3 1 8 End Cap 29 Y 3 Upper Frame End Cap 30 Y 2 3 8 x 2 Rubber Bumper 31 Q 34 x 2 Cover 32 Small Pulley 33 Pulley 34 Olympic Sleeve 35 Weight Bar Sleeve 36 Hook 37 1 End Cap 38 Q 1 34 End Cap 39 Plastic Ring 40 Ankle Strap 41 Single Handle 42 15 link Chain 43 10 link Chain 44 5 link Chain 45 6 Grip 46 Sliding Sleeve 47 M10 x 2 34 Carriage Bolt 48 M10 x 4 Carriage Bolt 49 M10 x 4 1 8 Carriage Bolt 50 M10 x 2 3 8 Carriage Bolt o ODDD R 2
12. te satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FHEE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufac
13. the Cross Brace 7 Secure each end of the Cross Brace to each Base Frame with four M10 x 2 3 8 Carriage Bolts 50 one 4 34 x 3 4 Bracket 22 four 34 Washers 57 and four M10 Aircraft Nuts 58 C Attach the Left Rear Support 5 onto the left Base Frame Secure it with two M10 x 3 VG Allen Bolts 55 four 34 Washers 57 and two M10 Aircraft Nuts 58 Repeat the same step to install the Right Rear Support 6 onto the other Base Frame DIAGRAM 1 STEP 2 See Diagram 2 A Do not tighten Nuts and Bolts until instructed to do so B Attach the Left Upright Beam 1 to the Left Rear Support 5 and onto the left Base Frame 3 C Secure it to the Base Frame with two M10 x 4 Allen Bolts 54 four 34 Washers 57 and two M10 Aircraft Nuts 58 D Secure it to the Left Rear Support with one M10 x 4 Carriage Bolt 48 one Y 34 Washer 57 and one M10 Aircraft Nut 58 from side Secure with one M10 x 5 8 Allen Bolt 63 and one Y 3 4 Washer 57 from top E Repeat A to D to install the Right Upright Beam 6 to the right Base Frame F Attach the Top Beam 4 to the Left amp Right Upright Beam Secure each end of the Top Beam to each Upright Beam with one 4 x 2 3 8 Curved Bracket 23 one M10 x 4 1 8 Allen Bolt 53 and one Y 34 Washer 57 to the upper hole one M10 x 4 1 8 Carriage Bolt 49 one Y 34 Washers 57 and one M10 Aircraft Nut 58
14. turer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is recommended during exercise 00 CARE AND MAINTENANCE Lubricate moving parts and Guide Rods with WD 40 or light oil periodically Inspect and tighten all parts before using the machine ON DO NOT use solvents Maximum user s weight 300 lbs Maximum weight on the Sliding Weight Post 300 Ibs Maximum weight on Leg Developer 100 Ibs Maximum weight on Weight Bar 300lbs Maximum weight Capacity 600 Ibs ONDA WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS The machine can be cleaned using a damp cloth and mild non abrasive detergent WARNING LABEL PLACEMENT d G A C S wi JAN NV L AA ction a The warning labels shown here have been placed on the back of Rear Support and Upper Frame
15. used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When order
Download Pdf Manuals
Related Search