Impex Marcy MWM-8150 User's Manual
Contents
1. i STEP 3 See Diagram 3 A Attach the Seat Support 8 to the Vertical Frame 4 Secure it with two M10 x 2 1 Carriage Bolts 65 one 4 x 2 Bracket 23 two 9 Washers 80 and two M10 Aircraft Nuts 82 Do not tighten the Nuts and Bolts yet B Attach the two Seat Support Frames 10 to the Seat Support and the Main Base frame 1 from each side Secure them to the Seat Support and Main Base Frame with two M10 x 2 9 Allen Bolts 75 four Y 34 Washers 80 and two M10 Aircraft Nuts 82 C Securely tighten all Nuts and Bolts installed in this step D Attach the Seat Pad 31 to Main Seat Support Secure it with two M8 x 2 v2 Allen Bolts 78 and two Y 5 8 Washers 79 E Attach two 1 Bushings 44 to the hole on the Leg Developer 9 Attach the Leg Developer to the open bracket on Main Seat Support Secure it with one M12 x 3 Allen Bolt 67 two O 1 Washers 81 and one M12 Aircraft Nuts 63 F Insert two Foam Tubes 21 halfway through the holes on Main Seat Support and Leg Developer Push four Foam Rolls 41 onto the Tubes from each end Plug four Foam Roll End Caps 60 into the Ends 12 STEP 4 See Diagram 4 A Attach two Y 1 Bushings 44 to the holes on the Upper Frame 5 Attach the Front Press Base 11 to the two Bushings Secure it with one M12 x 4 1 8 Allen Bolt 68 two 1 Washers 81 and one M12 Aircraft Nuts 62. The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase ROD 23
3. 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands and feet away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 N
4. Qty 1 67 M12 x 3 Allen Bolt Qty 1 Mm 77 M10 x 3 An Allen Bolt Qty 1 1 76 M10 x 3 Allen Bolt Qty 1 MM 75 M10 x 2 3 Allen Bolt Qty 8 0 2 8 4 5 6 7 8 9 10 11 12 13 14 15 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler or scale to measure the size 66 M10 x 2 4 Carriage Bolt Qty 2 65 M10 x 2 An Carriage Bolt Qty 6 ss 74 M10 x 2 3 Allen Bolt Qty 8 T D 73 M10 x 2 Allen Bolt Qty 2 Mm 72 M10 x 1 4 Allen Bolt Qty 8 n 78 M8 x 2 3 Allen Bolt Qty 4 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler or scale to measure the size MM 71 M10 x 1 Allen Bolt Qty 5 70 M10 x 3 Allen Bolt Qty 6 TT O 63 M12 Aircraft Nut 81 Y 1 Washer Oty 4 Qty 8 79 Y Washer Oty 4 80 3 Washer m Qty 61 82 M10 Aircraft Nut Qty 34 10 11 12 13 14 15 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler or scale to measure the size amp 39 L Shaped Pin 44 Y 1 Bushing Qty 1 Oty 4 38 C clip Qty 3 43 x 3 Pulley Bushing Qty 8 42 x 4 Long Pulley Bushing Qty 2 37 Chain Qty 1 ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine Two Adjustable Wrenches two Allen Wrenches and one Philips Screwdriver NOTE It
5. 3 Do not over tighten the Nut and Bolt Make sure the Front Press Base is able to move smoothly B Attach the Right Butterfly 13 to the Front Press Base Secure it with one M12 x 4 3 8 Allen Bolt 69 two O 1 Washer 81 and one M12 Aircraft Nut 63 C Repeat the Steps B above to install the Left Butterfly 12 D Attach a Butterfly Pulley Bracket 15 to the Vertical Frame 4 Secure it with one M10 x 3 2 Allen Bolt 77 two Y Y Washers 80 and one M10 Aircraft Nut 82 E Attach one Swivel Pulley Brackets 16 to each end of the Butterfly Pulley Bracket Secure each Bracket with one M10 x 2 Allen Bolt 74 two Y Washers 80 and one M10 Aircraft Nut 82 Do not over tighten Make sure the Brackets are able to swivel freely F Attach the Backrest Board 30 to the Vertical Frame Secure it with two M8 x 2 12 Allen Bolts 78 and Y 5 8 Washers 79 CABLE LOOP DIAGRAM STEP 5 See Diagram 5 8 Cable Loop Diagram A B C Attach the 153 Upper Cable 34 to the opening at the front of the Upper Frame 5 Note The Ball Stopper on the cable should be underneath the Frame Attach a Pulley 47 to the opening Secure it with one M10 x 2 we Allen Bolt 74 two 7 8 x 5 8 Pulley Bushings 43 and one M10 Aircraft Nut 82 Draw the Cable towards the back of the machine to the opening on the Upper Frame Attach a Pulley to the opening Secure i
6. Double Floating Pulley Bracket 29 If the cables are too loose move the Pulley up one hole If the cables are too tight move the Pulley down one hole For best performance of the machine adjust the Cables so the Selector Stem Top Plate on the weight stack is 14 above the first plate To select the weight push down on the Selector Stem to close the gap then insert the selector pin This will remove the slack in the cable system so the range of motion is smooth and tight Connect the Shiver Bar 20 to a Chain 37 with a C clip 38 Connect the Chain to the Lower Cable with another C clip 19 DIAGRAM 7 Bis i gt i S IN NO PARTS LIST KEY NO DESCRIPTION OONDOARWND Main Base Frame Rear Base Frame Vertical Support Frame Vertical Frame Upper Frame Top Socket Assembly Guide Rod Seat Support Leg Developer Seat Support Frame Front Press Base Left Butterfly Right Butterfly Front Press Handle Butterfly Pulley Bracket Swivel Pulley Bracket Crossed Double Floating Pulley Bracket Rotating Ring Lat Bar Shiver Bar Foam Tube Foot Plate 4 x 2 Bracket 4 x 2 Bracket 1 7 8 Square Bracket L shaped Cable Retainer Weight Stack Cover Selector Rod Double Floating Pulley Bracket Backrest Board Seat Pad Selector Stem Weight Plate 153 Upper Cable 125 Butterfly Cable 131 Lower Cable Chain C Clip L shaped Pin Butterfly Foa
7. IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or prolits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you
8. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MW M 8150 Retain This Manual for Reference 08 04 08 OWNER S MANUAL FITNESS PRODUCTS MARCY HOME GYM MWM 8150 4 KA NN SD IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN ati 1 IMPORTANT SAFETONOWSE nee 2 HARDWARE PACK alienate ental chasers tenet ddd dd a nds 4 ASSEMBLY INSTRUCTIONS ac akc bk ae ehe 8 PARIS LIS Radka ooh Z de Eege 21 RESISTANGE GHAR Tirana 22 WARRANT Y OO O ANNC AA 23 ORDERING GE 23 BEFORE YOU BEGIN Thank you for selecting the Marcy Home Gym MWM 8150 by IMPEX FITNESS PRODUCTS For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri
9. O 16 STEP 6 See Diagram 6 8 Cable Loop Diagram A Attach one end of the 125 Butterfly Cable 35 to the hook on the Right Butterfly 13 B Draw the Cable to the right Swivel Pulley Bracket 16 C Attach a Pulley to the bracket Secure it with one M10 x 1 9 Allen Bolt 72 two Y 34 Washers 80 and one M10 Aircraft Nut 82 D Draw the Cable around the Pulley then downward Attach the Cable to a Crossed Double Floating Pulley Bracket 17 Install another Pulley Let the Bracket hang for now E Pull the Cable around the Pulley then upward to the left Swivel Pulley Bracket Repeat Procedure C above to install a Pulley F Draw the Cable to the left Butterfly Attach the end to the hook on the Left Butterfly G Push one Butterfly Foam Roll 40 onto the Right Butterfly Attach a Front Press Handle 14 to the Right Butterfly Secure it with one M10 x 2 9 Allen Bolt 75 and Y Y Washer 80 Repeat the same procedure to install the Foam Roll and Handle to Left Butterfly 17 DIAGRAM 6 STEP 7 See Diagram 7 8 Cable Loop Diagram A B C D m a O I Attach the 131 Lower Cable 36 to the opening on the bottom of the Leg Developer 9 Attach a Pulley to the opening Secure it with one M10 x 2 12 Allen Bolt 74 two 7 8 x 5 8 Pulley Bushings 43 and one M10 Aircraft Nut 82 Draw the Cable underneath the Pulley to the opening in
10. between the two Seat Support Frames 10 Attach a Pulley to the opening Secure it with one M10 x 2 34 Allen Bolt 75 two Y 34 Washers 80 and one M10 Aircraft Nut 82 Insert a M10 x 2 1 2 Allen Bolts 74 through the hole on the two Seat Support Frames under the Pulley Secure the Bolt with two Y 34 Washers 80 and one M10 Aircraft Nut 82 Draw the Cable underneath the Pulley along the Main Base Frame to the opening on the bottom of the Vertical Frame 4 Repeat Procedure B above to install another Pulley Pull the Cable upward to the Crossed Double Floating Pulley Bracket 17 previously installed in Step 6 Install another Pulley with one M10 x 1 9 Allen Bolt 72 two Y Washers 80 and one M10 Aircraft Nut 82 Draw the Cable over the Pulley then downward to the opening on the bottom of Vertical Support Frame 3 Repeat Procedure B to install another Pulley Pull the Cable around the Pulley then upward to the Double Floating Pulley Bracket 29 previously installed in Step 5 Install another Pulley with one M10 x 1 Allen Bolt 72 two Y Washers 80 and one M10 Aircraft Nut 82 Draw the Cable around the Pulley then pull downward to the bracket on the back of the Vertical Support Frame Secure the Cable to the bracket with one M10 x 1 Allen Bolt 71 two Y Washers 80 and one M10 Aircraft Nut 82 Adjust the tension of the Cable by adjusting the Pulley position on the
11. ever operate the machine if the machine is not functioning properly 12 A spotter is recommended during exercise CARE AND MAINTENANCE 1 Lubricate moving parts with WD 40 or light oil periodically 2 Inspect and tighten all parts before using the machine 3 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents 4 Maximum user s weight 300 lbs WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL REPLACEMENT AOL foo 3 Wj EF EE EE E A MN DO NOT MISUSE THIS EQUIPMENT The possibility of serious injuries or ith or both applicable may occur if caution is not used All ings and inst Read users mus The warning labels shown here have been placed on the Rear Base and Upper Frame If the labels are missing or illegible please call customer service at 1 800 888 8899 for replacements Apply the labels in the location shown 3 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler or scale to measure the size mlm 69 M12 x 4 Allen Bolt Qty 2 68 M12 x 4 Allen Bolt
12. is strongly recommended that this machine to be assembled by two or more people to avoid possible injury STEP 1 See Diagram 1 A B Gj Insert the two Guide Rods 7 into the holes on the Rear Base Frame 2 Secure it with two M10 x 1 Allen Bolts 71 and 34 Washers 80 from the bottom Slide two O 2 1 2 Rubber Bumpers 53 onto the Guide Rods from top to bottom Attach the Vertical Frame 4 onto the Main Base Frame 1 Secure it with two M10 x 2 Y2 Carriage Bolts 65 one 4 4 x 2 Bracket 23 two 34 Washers 80 and two M10 Aircraft Nuts 82 NOTE Do not tighten all the Nuts and Bolts until instructed to do so D Attach the Main Base Frame to the Rear Base Frame Attach the Vertical Support m Frame 3 onto the Rear Base Frame Align the holes Secure them together with two M10 x 2 4 Carriage Bolts 66 two 3 4 Washers 80 and two M10 Aircraft Nuts 82 Attach the top of Vertical Support Frame to the Vertical Frame Secure it with two M10 x 5 8 Allen Bolts 70 and two Y 3 4 Washers 80 Attach the two Foot Plates 22 to the front of Main Base Frame from each side Align the holes Secure the two Foot Plates to the Main Base Frame with two M10 x 2 e Carriage Bolts 65 two 34 Washers 80 and two M10 Aircraft Nuts 82 DIAGRAM 1 9 STEP 2 See Diagram 2 A Slide 14 Weight Plates 33 onto the Guide Rods Make sure the deep groo
13. m Roll Foam Roll O 7 8 x Y Long Pulley Bushing O 7 8 x 5 8 Pulley Bushing Y 1 Bushing Plastic Ring Rivet Pulley Main Base Frame End Cap Handle Grip 1 7 8 x 1 7 8 Rubber Bumper Q ty 4 51 4 1 8 x 2 1 8 Rubber Bumper 4 52 139 Rubber Bumper 4 53 Y 2 12 Rubber Bumper 4 54 Y 1 ve Rubber Bumper 4 55 1 12 Bushing 4 56 1 End Cap 2 57 2 Square End Cap 4 58 1 Cone shaped End Cap 4 59 Y 1 End Cap 2 60 Foam Roll End Cap 4 61 Single Handle 4 62 Ankle Strap 1 63 M12 Aircraft Nut 2 64 M6 x 5 8 Philips Screw 4 65 M10 x 2 Lei Carriage Bolt 2 66 M10 x 23 Carriage Bolt 4 67 M12 x 3 Allen Bolt 2 68 M12 x 4 1 8 Allen Bolt 4 69 M12 x 4 3 8 Allen Bolt 4 70 M10 x 5 8 Allen Bolt 2 71 M10 x 1 Allen Bolt 2 72 M10 x 1 9 Allen Bolt 2 73 M10 x 2 Allen Bolt 4 74 M10 x 2 12 Allen Bolt 2 75 M10 x 23 Allen Bolt 2 76 M10 x 3 Allen Bolt 4 77 M10 x 3 12 Allen Bolt 4 78 M8 x 2 1 Allen Bolt 2 79 5 8 Washer 4 80 Y Washer 4 81 1 Washer 4 82 M10 Aircraft Nut 14 5 Allen Wrench Tool 4 6 Allen Wrench Tool 1 8 Allen Wrench Tool 4 4 3 1 2 4 2 8 4 4 4 16 4 6 1 21 00O9PP 00POoO0OOD DO P P D _ NDPrR D _ ULB yes JO ue yIepng Jo SANIE Aiea Aeu sjyBjem enjoy ejewIXOJdde eJe sioquiny M PALO 0 06 os Le z 22
14. t with one M10 x 3 Allen Bolt 76 two O 7 8 x 34 Long Pulley Bushings 42 and one M10 Aircraft Nut 82 Draw the Cable around the Pulley then pull back towards the open bracket on the Front Press Base 11 Attach a Pulley to the bracket Secure it with one M10 x 1 9 Allen Bolt 72 two 9 Washers 80 and one M10 Aircraft Nut 82 Draw the Cable around the Pulley through the hole on the Vertical Frame to the open bracket on the rear of Vertical Frame 4 Repeat Procedure E above to install another Pulley Draw the Cable around the Pulley then downward Attach the Cable to in between the two Double Floating Pulley Brackets 29 Repeat Procedure E to install a Pulley Let the bracket hanging for now Draw the Cable around the Pulley then pull the Cable upward to the open bracket on the Top Socket Assembly 6 Attach a Pulley to the bracket Secure it with one M10 x 2 Allen Bolt 73 one L shaped Cable Retainer 26 two Y 3 4 Washers 80 and one M10 Aircraft Nut 82 Draw the Cable to the other open bracket on the Top Socket Assembly Repeat Procedure to install another Pulley Pull the Cable downward between the two Guide Rods through a O 1 9 Rubber Bumper 52 to the Selector Rod 28 Fully thread the bolt at the end of the Cable into the top opening on the Selector Rod Connect the Lat Bar 19 to the Upper Cable with a C clip 38 15 DIAGRAM 5 x mM IN 4 zai L
15. ve on the Weight Plates all facing the front of the machine and downward Insert the Selector Rod 28 through the center hole on the Weight Plates Slide the Selector Stem 432 onto the Guide Rods Use the L shaped Pin 439 to select total weights to exercise Please refer to the Weight Resistance Chart in page 22 B Place the Upper Frame 5 onto the Vertical Frame 4 Secure them with one M10 x 2 Allen Bolt 75 two Y 34 Washers 80 and one M10 Aircraft Nut 82 from the side One M10 x 2 39 Allen Bolt 75 one 1 7 8 Square Bracket 25 two Y Y Washers 80 and one M10 Aircraft Nut 82 from front C Attach the holes on the Top Socket Assembly 6 onto the two Guide Rods 7 Secure it with two M10 x 1 Allen Bolts 71 and two Y 9 Washers 80 D Attach the other end of Top Socket Assemble to the Upper Frame Secure it with one M10 x 2 Allen Bolts 75 one M10 x 2 1 Allen Bolt 74 two Y Y Washers 80 one 4 x 2 Bracket 24 one 9 Washer 80 and one M10 Aircraft Nuts 82 E Attach the Weight Stack Cover 27 to Rear Base Frame 2 and Top Socket Assembly Secure it with four M10 x 5 8 Allen Bolts 70 and four 3 4 Washers 80 F Securely tighten all Nuts and Bolts previously installed in Sept 1 and Step 2 10 DIAGRAM 2 a 63 60 Naja LA ma d MEL Lib hb i tt AL FA A A TEN TE M jaj EI a w a a awa ama
Download Pdf Manuals
Related Search