Impex IGS-8859 Owner's Manual
Contents
1. Place the Seat Pad 24 onto the Seat Bracket 12 Secure it with four M8 x 1 3 8 Allen Bolts 59 and 5 8 Washers 65 Attach the Arm Curl Pad 25 to the Arm Curl Bracket 22 Secure it with two M8 x 5 8 Allen Bolts 60 and 5 8 Washers 65 Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand 15 Insert the M8 x 3 Le Allen Bolt 58 through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket Secure the Bolt with two 5 8 Washers 65 and one M8 Aircraft Nut 68 Do not over tighten the Nut and Bolt The Bolt needs to be able to slide on the track freely Insert the Arm Curl Stand into the storage post behind the upright beams when using the Lat Bar or Leg Developer DIAGRAM 4 STEP5 See Diagram 5 A Attach the Leg Developer 9 to the Main Seat Support 3 Secure it with one M10 x 3 Ye Allen Bolt 52 two 34 Washers 64 and one M10 Aircraft Nut 67 B Insert two Foam Tubes 20 halfway through the holes on the Leg Developer Push four Foam Rolls 30 onto the Tubes from both ends Plug four Foam Roll End Caps 37 into the ends Attach an Olympic Sleeve 34 onto the weight post on Leg Developer Attach a Spring Clip 28 onto the Sleeve Attach the Arm Curl Handle 16 to the back hole on the Leg Developer Secure it with one 3 Lock Pin 32 Attach the Abdominal Strap 31 to the front hole on the Leg Developer Sec2. Cable 48 to a Pulley 46 Attach the Pulley to the opening on top of the Lat Bar Frame Secure the Pulley with one M10 x 2 12 Allen Bolt 54 two Pulley Bushings 47 and one M10 Aircraft Nut 67 Draw the Cable over the Pulley to the open bracket on the back of the Lat Bar Frame Attach a Pulley to the bracket Secure it with one M10 x 1 9 Allen Bolt 56 two Y 3 Washers 64 one L shaped Bracket 21 and one M10 Aircraft Nut 67 Draw the Cable downward and to the open bracket on the Sliding Weight Holder 14 Secure the end of Cable to the bracket with one M10 x 1 Allen Bolt 57 two Y Y Washers 64 and one M10 Aircraft Nut 67 Insert a M10 x 2 3 8 Allen Bolt 55 through the hole on the Lat Bar Frame and secure it with a M10 Aircraft Nut 67 Attach an Olympic Sleeve 34 onto the weight post on the Sliding Weight Holder Attach a Spring Clip 28 to the Olympic Sleeve Connect the Lat Bar 11 to the Cable with a C clip 29 Place the Lat Bar onto the holder on the Lat Bar Frame Remove the entire Lat Bar apparatus and place it in the storage post behind the upright beams when using the Arm Curl or Leg Developer DIAGRAM 3 A A AUN e Vo e e o un v Y on dl e STEP4 See Diagram 4 A B x C D m Attach the Backrest Board 23 to the Backrest Supports 19 Secure it with four M8 x 1 3 8 Allen Bolts 59 and 5 8 Washers 65
3. However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 2 3 4 00 10 12 13 14 15 16 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine Only one person at a time should use the machine If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors Keep hands away from all moving parts Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer Do not place any sharp object around the machine Disabled person should not use the machine without a qualified person or physician in attendance Before using the machine to exercise always do stretching exercises to properly warm up Never operate the machine if the machine is not functioning properly A spotter is recommended during exercise Maximum user
4. M10 x3 Allen Bolt M10 x 2 34 Allen Bolt M10 x 2 1 Allen Bolt M10 x 2 3 8 Allen Bolt M10 x 1 3 Allen Bolt M10 x 1 Allen Bolt M8 x 3 12 Allen Bolt M8 x 1 3 8 Allen Bolt M8 x 5 8 Allen Bolt M6 x 5 8 Philips Screw ST3 x 3 8 Philips Screw amp 1 Washer Y Washer 5 8 Washer M12 Aircraft Nut M10 Aircraft Nut M8 Aircraft Nut Rotating Ring Plastic Ring Rotating Ring Bushing Rivet BNN 2N xNNN N0 222Nn 0pNn wesch IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by a IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or l
5. Please read all SH instructions carefully before using this product Table of Contents IRON GRIP STRENGTH Safety Notice DELUXE COMBO BEN CH Hardware Pack IGS 8859 Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model IGS 8859 Retain This Manual for Reference 08 21 07 OWNER S IMPEX INC MANUAL 14777 Don Julian Rd City of Industry CA 91746 Tel 800 999 8899 Fax 626 961 9966 TABLE OF CONTENTS BEFORE YOU BEGINN sanken 1 IMPORTANT SAFETY NEIE keete een 2 HARDWARE PAG ts SO 4 ASSEMBLY INSTRUCTIONS u 6 EXPLODED DIAGRAM nee 12 PARTS LIST ae er meee tere casado 13 WARRANTY E 14 EIER le Ee GE 14 BEFORE YOU BEGIN Thank you for selecting the IRON GRIP STRENGTH IGS 8859 COMBO BENCH by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guarantee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety
6. e selected slot on the Upright Beams to obtain the desired backrest incline STEP 2 See Diagram 2 A Connect the Left Support Frame 4 to the Right Support Frame 5 Align the holes Secure them together with two M10 x 3 9 Allen Bolts 51 four 9 Washers 64 and two M10 Aircraft Nuts 67 Do not tighten the Nuts and Bolts yet B Attach the Main Seat Support 3 to both Left amp Right Support Frames Attach the Front Post 10 to the Main Seat Support Align the holes Secure them together with four M10 x 2 9 Carriage Bolts 49 34 Washers 64 and M10 Aircraft Nuts 67 C Securely tighten all Nuts and Bolts previously installed DIAGRAM 2 STEP3 See Diagram 3 A D O O Attach the side holes on the two Backrest Supports 19 to the pivot on the Main Seat Support 3 Align the holes Secure them together with one M12 x 6 9 Allen Bolt 50 two Y 1 Washers 63 and one M12 Aircraft Nut 66 Do not over tighten the Nut and Bolt Make sure the Backrest Supports are able to swivel Attach the Seat Bracket 12 onto the Main Seat Support Secure it with two M10 x 2 9 Allen Bolts 53 four 34 Washers 64 and two M10 Aircraft Nuts 67 Slide the Sliding Weight Holder 14 onto the Lat Bar Frame 8 from the bottom Insert the Lat Bar frame into the opening on top of the Front Post 3 and secure it with a M18 x 83 8 Lock Knob 36 Attach the 59
7. iable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information Model Description of Parts Part Number Date of Purchase PONS 14
8. oty Qty Oty Oty Oty Qty 2 1 2 1 1 1 58 MB x 3 An Allen Bolt Qty 1 59 MB x 1 Allen Bolt Qty 8 60 MB x Bn Allen Bolt Qty 2 H 1 2 3 4 5 6 789 10 11 12 13 14 15 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 29 C clip Qty 1 32 3 Lock Pin Qty 2 28 Spring Clip Qty 2 47 Pulley Bushing Qty 2 0 63 21 Washer 64 Gin Washer 65 Washer Qty 2 Qty 26 Qty 12 E 66 M12 Aircraft Nut 67 M10 Aircraft Nut 68 M8 Aircraft Nut Qty 1 Qty 21 Qty 1 mm 0D 1 2 3 4 6 6 7 8 9 10 11 12 13 14 15 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended two or more people assembling this machine to avoid possible injury STEP1 See Diagram 1 A Attach the Left Support Frame 4 and the Rear Support 13 to the Left Upright Beam 1 Align the holes Secure them together with four M10 x 2 9 Carriage Bolts 49 Y 34 Washers 64 and M10 Aircraft Nuts 67 Do not tighten the Nuts and Bolts yet Repeat the same procedure to install the Right Support Frame 5 and the other Rear Support to the Right Upright Beam 2 B Insert two Crutches 7 into the openings on the top of the Upright Beams Secure them with two M18 x Y Lock Knobs 35 C Place the Backrest Adjustment Bar 6 on th
9. s weight 300 lbs Maximum weight on uprights 600 lbs Maximum weight on leg developer 100 lbs Maximum weight on Lat Bar 100lbs CARE AND MAINTENANCE 1 Inspect and tighten all parts before using the machine 2 The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS WARNING LABEL REPLACEMENT Y WARNING gt SERIOUS INJURY MAY OCCUR ercise or hang The Warning Labels shown here have been placed on the Support Frame and Lat Bar If the labels are missing or illegible please call customer service at 1 800 999 8899 for replacement Apply the labels in location shown 3 HARDWARE PACK NOTE The following parts are not drawn to scale Please use your own ruler to measure the size 50 M12 x 6 An Allen Bolt Qty 1 51 MIO x 3 An Allen Bolt 52 M10 x 3 4 Allen Bolt 53 M10 x 2 An Allen 54 M10 x 2 4 Allen SR 55 M10 x 2 Allen 56 M10 x 1 f Allen 57 M10 x 1 Allen Bolt Qty 1 49 M10 x 2 4 Carriage Bolt Oty 12 Bolt Bolt Bolt Bolt O
10. ure it with one 3 Lock Pin 32 Pull up and flip the Arm Curl Pad along the track to face the back when doing Abdominal exercises using the Abdominal Strap Remove the Arm Curl Stand Arm Curl Handle and Abdominal Strap when doing Leg Developer exercises C O m T DIAGRAM 5 11 A ME Oe Jas VW EXPLODED DIAGRAM PARTSLIST KEYNO DESCRIPTION 1 Left Upright Beam 2 Right Upright Beam 3 Main Seat Support 4 Left Support Frame 5 Right Support Frame 6 Backrest Adjustment Bar 7 Crutch 8 Lat Bar Frame 9 Leg Developer 10 Front Post 11 Lat Bar 12 Seat Bracket 13 Rear Support 14 Sliding Weight Holder 15 Arm Curl Stand 16 Arm Curl Handle 17 Abdominal Strap Connector 18 Strap Buckle 19 Backrest Support 20 Foam Tube 21 L shaped Bracket 22 Arm Curl Bracket 23 Backrest Board 24 Seat Pad 25 Arm Curl Pad 26 2 3 8 x 2 Sleeve 27 4 Sleeve 28 Spring Clip 29 C clip 30 Foam Roll 31 Abdominal Strap 32 3 Lock Pin 33 Y 1 Bushing 34 Olympic Sleeve 35 M18 x Lock Knob 36 M18 x 3 8 Lock Knob 37 Foam Roll End Cap 38 Y 1 End Cap 39 1 Square End Cap 40 2 Square End Cap 41 4 x Square End Cap 42 2 3 8 Square End Cap 43 1 5 8 Square End Cap 44 6 Handle Grip 45 Rubber Bumper 46 Pulley 47 Pulley Bushing 48 59 Cable 49 M10 x 2 Carriage Bolt 50 M12 x 6 Allen Bolt QTY 13 M10 x 3 34 Allen Bolt
Download Pdf Manuals
Related Search