Impex IGS-5100 Owner's Manual
Contents
1. STEP 1 See Diagram 1 A Do not tighten all nuts and bolts until instructed to do so B Attach one Guide Rod 12 onto a Base Frame 1 Secure the Guide Rod to the Base Frame with one M10 x 1 Allen Bolt 74 and Y 94 Washer 86 from the bottom C Slide one Lower Safety Stop Frame 90 onto the Guide Rod from the top then slide one Safety Stop Frame 26 onto the Guide Rod D Attach the Base Frame 1 to the Left Vertical Frame 3 Attach the Cross Brace 8 to the back of the Left Vertical Frame 8 Align the holes and secure the Base Frame Left Vertical Frame and the Cross Brace together with two M10 x 2 34 Carriage Bolts 70 two 34 Washers 86 and two M10 Aircraft Nuts 83 E Insert the top of the Guide Rod 12 into the tube on the Left Vertical Frame 3 Secure it with one M8 x 1 5 8 Allen Bolt 76 and M8 Aircraft Nut 75 F Attach one Front Vertical Frame 2 onto the Base Frame 1 Secure it with two M10 x 2394 Carriage Bolts 70 one 4 x 2 Bracket 36 two Y 32 Washers 86 and two M10 Aircraft Nuts 83 G Attach the top of the Front Vertical Frame 2 to the top of the Left Vertical Frame 3 Secure it with two M10 x 1 Allen Bolts 74 and Y 34 Washers 486 H Attach a Safety Hook 91 to the Lower Safety Stop Frame 90 Securely it with one M10 x 1 Allen Bolt 74 two 34 Washers 86 and one M10 Aircraft Nut 83 Attach the Safety Hook into the2. 2 4 2 21 N o o 00 19 19 09 09 9 21 007 09210 Sc PO DD III DD FERIEN MULTI PURPOSE BENCH HARDWARE PACK 41 M8 x 5 8 Allen Bolt Qty 2 MULTI PURPOSE BENCH HARDWARE PACK d d 50 M10 Aircraft Nut 51 M8 Aircraft Nut Qty 7 Qty 2 39 3 4 Washer 38 0 5 8 Washer Qty 16 Qty 14 U 52 0 1 2 Bushing Qty 2 EOS NN 5 20 Lock Pin Qty 2 40 M10 x 5 8 Allen Bolt Qty 6 S 37 Spring Clip Qty 1 mm I Wt MULTI PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended this machine be assembled by two or more people to avoid possible injury STEP1 See Diagram 1 A Attach the Front Post 3 to the Front Stabilizer 17 B Secure it with three M10 x 5 8 Allen Bolts 40 and 5 8 Washers 39 DIAGRAM 1 24 STEP 2 See Diagram 2 A Attach the rear of Main Seat Support 1 to the Rear Stabilizer 4 Secure it with two M10 x 2 3 8 Carriage Bolts 47 one 5 1 8 x 2 3 8 Bracket 21 two Y 34 Washers 39 and two M10 Aircraft Nuts 50 B Attach the Wheel 14 to the Rear Stabilizer Secure it with one M8 x 5 1 8 Allen Bolt 44 two 5 8 Washers 38 and one M8 Aircraft Nut 51 C Place the Main Seat Support onto the Front Post 3 Secure it with two M10 x 2 37 Carriage Bolts 49
3. on the Leg Developer Secure it with a Lock Pin 20 E Pull up and flip the Arm Curl Pad along the track to face the back of the machine when doing abdominal exercises using the Abdominal Strap F Remove the Arm Stand and Abdominal Strap when doing Leg Developer exercises MULTI PURPOSE BENCH PARTS LIST KEY NO DESCRIPTION Main Seat Support Leg Developer Holder Front Post Rear Stabilizer Seat Bracket Arm Curl Stand Backrest Incline Support Seat Pad Backrest Board Backrest Support Arm Curl Pad Leg Developer Y 2 Leg Developer Bushing Wheel T shaped Lock Pin Foam Tube Front Stabilizer Axle Arm Curl Handle Lock Pin 5 1 8 x 2 3 8 Bracket 5 1 8 x 234 Bracket Arm Curl Bracket Abdominal Strap Abdominal Strap Connector Strap Buckle Vinyl Foam Roll Olympic Sleeve Y 2 Cone shaped End Cap Y 1 Cone shaped End Cap Foam Roll End Cap 6 Grip Sleeve 1 Square End Cap Y 1 End Cap Lock Knob Spring Clip Y 5 8 Washer 34 Washer M10 x 5 8 Allen Bolt M8 x 5 8 Allen Bolt M10 x 1 37 Allen Bolt M10 x 7 14 Allen Bolt M8 x 5 1 8 Allen Bolt M8 x 3 12 Allen Bolt M8 x 1 5 8 Allen Bolt M10 x 2 3 8 Carriage Bolt M10 x 3 Carriage Bolt M10 x 2 34 Carriage Bolt M10 Aircraft Nut M8 Aircraft Nut Y v2 Bushing 1 x 3 8 Bushing 31 O ty OF IMPEX INC LIMITED WARRANTY IMPEX Inc IMPEX warrants this product to be free fro
4. selected hole on the back of Front Vertical Frame I Repeat Procedure B through H to install the other side DIAGRAM 1 STEP 2 See Diagram 2 A Attach the Rear Vertical Frame Base 7 to the Cross Brace 8 from the bottom Attach the Rear Vertical Frame 6 onto the Cross Brace on the top Align the holes and secure them together with two M10 x 2 34 Carriage Bolts 70 34 Washers 86 and M10 Aircraft Nuts 83 B Attach the Backrest Board 34 to the Rear Vertical Frame Secure it with two M8 x 3 37 Allen Bolts 80 and 5 8 Washes 87 DIAGRAM 2 STEP 3 See Diagram 3 A Attach the Weight Glide Post 5 to the bracket on the Rear Vertical Frame Base 7 Secure it with two M10 x 2 Carriage Bolts 72 34 Washers 86 and M10 Aircraft Nuts 83 B Slide the Sliding Weight Post 22 onto the Weight Glide Post from the top Make sure the Cable connecting bracket on the Sliding Weight Post faced up C Attach the rear of the Upper Frame 11 to the top of the Weight Glide Post 5 Secure it with two M10 x 2 Carriage Bolts 72 94 Washers 86 and M10 Aircraft Nuts 83 D Attach the Upper Frame to the Rear Vertical Frame 6 Secure it with one M10 x 2 Carriage Bolt 72 94 Washer 86 and M10 Aircraft Nut 83 E Attach each end of the two Upper Support Frames 9 to the two Front Vertical Frames 2 Secure each Upper Support Frame with one 4 Ben
5. NOTE Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model IGS 5100 Retain This Manual for Reference 08 15 06 OWNER S MANUAL VI X IRON GRIP STRENGTH DELUXE SMITH MACHINE IGS 5100 IMPEX INC 14777 DON JULIAN RD CITY OF INDUSTRY CA 91746 Tel 800 999 8899 Fax 626 961 9966 ww impex fitness com info impex fitness com TABLE OF CONTENTS BEFORE YOU BEGIN ea 1 IMPORTANT SAFETY NOTICES nen 2 SMITH MACHINE HARDWARE PACK cocciccoccnnccccccconnnnnnncnnnannnnnnnnnnnnnnncnnnnnnos 4 SMITH MACHINE ASSEMBLY 5 8 EXPLODED DINARS een ehe ee 20 SMITH MACHINE PARTS LIS T 255 uh st ox ia a ei 21 MULTI PURPOSE BENCH HARDWARE DACH eee 22 MULTI PURPOSE BENCH ASSEMBLY INSTRUCTIONS 24 EXPLODED DIAGRAM rumes cx bt OK Taa dana 30 MULTI PURPOSE BENCH PARTS UGIN 31 WARRANTY aid AKAKAN kuky Ki KN 32 ORDERING PARTS iiid edge 32 BEFORE YOU BEGIN Thank you for selecting the IRON GRIP STRENGTH IGS 5100 Smith Machine by IMPEX INC For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to provide you complete customer satisfaction If you have any questions or find there are missing or damaged parts we guar
6. STEP 5 See Diagram 5 amp Cable Loop Diagram A Attach the 133 Cable 31 to the front opening on the Upper Frame 11 Attach a Pulley 38 to the opening Secure it with one M10 x 2 1 8 Allen Bolt 73 two Y 1 x 4 Pulley Bushings 51 and one M10 Aircraft Nut 83 Make sure the ball stopper on the Cable is underneath the Frame B Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper Frame Attach a Pulley to the opening Secure it with one M10 x 2 1 8 Allen Bolt 73 two Y 1 x 14 Pulley Bushings 51 and one M10 Aircraft Nut 83 C Draw the Cable around the Pulley then downward Attach a Pulley in between the two Double Floating Pulley Brackets 35 Secure the Pulley with one M10 x 1 9 Allen Bolt 77 two Y 34 Washers 86 and one M10 Aircraft Nut 83 Let the Bracket hanging for now D Draw the Cable around the Pulley then up to the back opening on the Upper Frame Attach a Big Pulley 39 to the bracket Secure it with one M10 x 2 1 8 Allen Bolt 73 two O 1 x 14 Pulley Bushings 51 and one M10 Aircraft Nut 83 E Draw the Cable around the Pulley then down to the Sliding Weight Post 22 Secure the Cable to the Sliding Weight Post with one M10 x 1 Allen Bolt 74 two Y 34 Washers 86 and one M10 Aircraft Nut 83 Attach two Olympic Sleeves 47 to the Sliding Weight Post Attach two Spring Clips 46 to the Sleeves F Conne
7. antee you complete satisfaction through direct assistance from our factory To avoid unnecessary delays please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you Toll Free Customer Service Number 1 800 999 8899 Mon Fri 9 a m 5 p m PST ww impex fitness com info impex fitness com IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions 1 Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine 2 Only one person at a time should use the machine 3 If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY 4 Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors 5 Keep hands away from all moving parts 6 Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine 7 Use the machine only for its intended use as described in this manual DO NOT use attachments not recommende
8. at 1 800 888 8899 for replacements Apply the labels in the location shown 3 SMITH MACHINE HARDWARE PACK 80 M8 x 3 3 4 Allen Bolt Qty 2 H mm 72 M10 x 2 Carriage Bolt Qty 8 71 M10 x 2 3 8 Carriage Bolt Qty 1 J m 70 M10 x 2 3 4 Carriage Bolt Qty 10 J mw 69 M10 x 3 1 2 Carriage Bolt Qty 2 SMITH MACHINE HARDWARE PACK INN III 76 M8 x 1 5 8 Allen Bolt Qty 2 74 M10 x 1 Allen Bolt Qty 16 au 77 M10 x 1 3 4 Allen Bolt Qty 6 0 amm 73 M10 x 2 1 8 Allen Bolt Qty 4 LE RR 78 M10 x 2 1 2 Allen Bolt Qty 1 amm 79 M10 x 3 1 2 Allen Bolt Qty 4 SMITH MACHINE HARDWARE PACK U 50 01 x 1 2 Pulley Bushing 51 01 x 1 4 Pulley Bushing Qty 2 Qty 8 j E 7 85 M6 Aircraft Nut 83 M10 Aircraft Nut 75 M8 Aircraft Nut Qty 2 Qty 38 Qty 2 86 03 4 Washer 87 05 8 Washer 57 Lock Ring Qty 59 Qty 6 Qty 2 mm 82 M6 x 1 1 4 Allen Bolt Qty 2 867 0 1 1 2 Washer Qty 2 SMITH MACHINE HARDWARE PACK 63 Short Chain Qty 1 62 Long Chain Qty 1 46 Spring Clip 49 C clip Qty 10 Qty 4 SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine Two Adjustable Wrenches and Allen Wrenches NOTE It is strongly recommended two or more people assembling this machine to avoid possible injury
9. ble underneath the Pulley to the opening on the Rear Vertical Frame Base 7 Install a Pulley with a M10 x 2 1 8 Allen Bolt 73 two Y 1 x 14 Pulley Bushings 51 and one M10 Aircraft Nut 83 Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket 35 previously installed in Step 5 Install another Pulley with one M10 x 1 9 Allen Bolt 77 two Y 34 Washers 86 and one M10 Aircraft Nut 283 Note After finishing the entire cable assembly come back to this step and adjust the tension of the cables To increase the tension move up the Pulley on the Double Floating Pulley Brackets To decrease the tension move the Pulley down D Draw the Cable around the Pulley then downward to the open bracket on the back of the Rear Vertical Frame 6 Install another Pulley E Draw the Cable around the Pulley and upward to the Single Floating Pulley Bracket 23 previously installed in Step 6 Secure the Cable to the Bracket with one M10 x 1 Allen Bolt 274 two Y 34 Washers 86 and one M10 Aircraft Nut 83 F Connect the Long Chain 62 to the Cable with a C clip 49 Depends on the exercise connect one of the Shiver Bar 24 V Bar 43 Ankle Strap 60 Single Handle 61 or the Triceps Rope 45 to the Chain with another C clip 17 DIAGRAM 7 STEP 8 See Diagram 8 A NOTE Help of another person is strongly recommended for this step Place the Lifting Sleeve 13 in betw
10. ct the Lat Bar 37 to the Cable with a Short Chain 63 and two C Clips 49 STEP 6 See Diagram 6 amp Cable Loop Diagram A Attach one end of the 78 Butterfly Cable 32 to the clip on the Right Butterfly 21 Draw the Cable to the right Butterfly Pulley Bracket 15 B Attach a Pulley 38 to the right Bracket Secure it with one M10 x 1 37 Allen Bolt 77 two Y Washers 86 and one M10 Aircraft Nut 83 C Draw the Cable around the Pulley then downward Attach the Cable to a Single Floating Pulley Bracket 23 Repeat Procedure B above to install a Pulley Let the Bracket hanging for now D Draw the Cable upward to the left Butterfly Pulley Bracket Repeat Procedure B above to install another Pulley E Draw the Cable around the Pulley they clip it to the Left Butterfly 20 DIAGRAM 6 STEP 7 See Diagram 7 amp Cable Loop Diagram A Insert the tip of the 133 Cable 31 through the opening on the Foot Plate 10 to the opening on the bottom of the Rear Vertical Beam 6 B Attach a Pulley 38 to the opening Attach the Foot Plate 10 to the Frame Align the holes and secure the Foot Plate Rear Vertical Frame and the Pulley with one M10 x 2 Allen Bolt 78 two 1 x 7 Pulley Bushings 50 and one M10 Aircraft Nut 83 Secure the Foot Plate to the Frame with one M10 x 2 3 8 Carriage Bolt 71 34 Washer 86 and M10 Aircraft Nut 83 C Draw the Ca
11. d by the manufacturer 8 Do not place any sharp object around the machine 9 Disabled person should not use the machine without a qualified person or physician in attendance 10 Before using the machine to exercise always do stretching exercises to properly warm up 11 Never operate the machine if the machine is not functioning properly 12 A spotter is recommended during exercise CARE AND MAINTENANCE Lubricate moving parts with WD 40 or light oil periodically Inspect and tighten all parts before using the machine The machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents 4 Maximum user s weight 300 lbs 5 Maximum weights on the rack 600 Ibs 6 Maximum weights on Leg Developer 100 lbs O N WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT IMPEX INC ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THESE INSTRUCTIONS G k JAN H IN WARNING LABEL PLACEMENT a Oc o g 228 2 2 5 ase lt 2 E S22 03 ac TT wo The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame If the labels are missing or illegible please call customer service
12. een the two Safety Stop Frames 26 Align the holes and insert the Weight Bar 28 all the way through Center the bar and secure it with two M8 x 3 8 Allen Bolts 88 on each side B Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the selected holes on the Front Vertical Frames 2 Attach a Long Olympic Sleeve 48 to each end of the Weight Bar Attach a Spring Clip 46 to the Sleeve C Attach six Weight Posts 27 to the Left amp Right Vertical Frames 4984 Secure each Weight Post with one M10 x 1 Allen Bolt 74 and Y 32 Washer 86 D Attach six Olympic Sleeves 47 to the Weight Posts Attach six Spring Clips 46 to the sleeves Insert the Left amp Right Bar Holders 16 amp 18 the Left amp Right Safety Catches 17 amp 19 into the selected holes on the Front Vertical Frames 2 EXPLODED DIAGRAM PARTS LIST KEY NO DESCRIPTION O 0 JO 0 Pt ON Base Frame Front Vertical Frame Left Vertical Frame Right Vertical Frame Weight Glide Post Rear Vertical Frame Rear Vertical Frame Base Cross Brace Upper Support Frame Foot Plate Upper Frame Guide Rod Lifting Sleeve Butterfly Base Butterfly Pulley Bracket Left Bar Holder Left Safety Catch Right Bar Holder Right Safety Catch Left Butterfly Right Butterfly Sliding Weight Post Single Floating Pulley Bracket Shiver Bar Shiver Bar Handle Safety Stop Frame Weight Post Weight Bar Pane
13. l 4 Bent Bracket 133 Cable 78 Butterfly Cable Butterfly Arm Pad Backrest Board Double Floating Pulley Bracket 4 x 2 Bracket Lat Bar Pulley Big Pulley 2 Square End Cap 5 34 Rubber Bumper 3 3 8 Rubber Bumper V Bar Linear Bearing Triceps Rope Spring Clip Olympic Sleeve Long Olympic Sleeve C clip 1 x V Pulley Bushing Q ty 2 51 1 x 44 Pulley Bushing 2 52 1 End Cap 1 53 1 Cone shaped End Cap 1 54 Y 2 End Cap 1 55 Y 1 1 8 x 5 8 Bushing 1 56 1 x 1 x Bushing 1 57 Lock Ring 1 58 1 x 5 8 Rubber Bumper 2 59 1 v2 Sleeve 1 60 Ankle Strap 1 61 Single Handle 2 62 Long Chain 1 63 Short Chain 1 64 Lat Bar Grip 1 65 6 Shiver Bar Handle Grip 1 66 3 1 8 Sleeve 1 67 1 v Washer 1 68 M6 x 5 8 Philips Screw 1 69 M10 x 3 Carriage Bolt 1 70 M10 x 2 84 Carriage Bolt 1 71 M10 x 2 3 8 Carriage Bolt 1 72 M10 x 2 Carriage Bolt 1 73 M10 x 2 1 8 Allen Bolt 1 74 M10 x 1 Allen Bolt 1 75 M8 Aircraft Nut 2 76 M8 x 1 5 8 Allen Bolt 6 77 M10 x 1 32 Allen Bolt 1 78 M10 x 2 Allen Bolt 2 79 M10 x 3 12 Allen Bolt 2 80 M8 x 3 34 Allen Bolt 2 81 M8 x 2 12 Allen Bolt 1 82 M6 x 1 4 Allen Bolt 2 83 M10 Aircraft Nut 1 84 Y End Cap 2 85 M6 Aircraft Nut 2 86 Y Washer 1 87 5 8 Washer 10 88 M8 x 3 8 Allen Bolt 1 89 Panel Screw 2 90 Lower Safety Stop Frame 2 91 Safety Hook 2 1 4 1 10 8
14. m defects in workmanship and material under normal use and service conditions for a period of two years on the Frame from the date of purchase This warranty extends only to the original purchaser IMPEX s obligation under this Warranty is limited to replacing or repairing at IMPEX s option All returns must be pre authorized by IMPEX Pre authorization may be obtained by calling IMPEX Customer Service Department at 1 800 999 8899 All freights on products returned to IMPEX must be prepaid by the customer This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes No other warranty beyond that specifically set forth above is authorized by IMPEX IMPEX is not responsible or liable for indirect special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyments or use costs of removal installation or other consequential damages or whatsoever natures Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied
15. one 5 1 8 x 2 34 Bracket 22 two 34 Washers 39 and two M10 Aircraft Nuts 50 DIAGRAM 2 25 STEP 3 See Diagram 3 A Attach the Leg Developer Holder 2 to the Main Seat Support 1 Secure it with one M10 x 5 8 Allen Bolt 40 and 34 Washer 39 from the top two M10 x 3 ei Carriage Bolts 48 two Y 3 4 Washers 39 and two M10 Aircraft Nuts 50 from the side B Attach the Leg Developer 12 to the Leg Developer Holder Secure it with one Axle 18 two M10 x 5 8 Allen Bolts 40 and two 34 Washers 499 C Attach an Olympic Sleeve 28 onto the weight post on the Leg Developer Attach a Spring Clip 37 to the Sleeve D Insert the Arm Curl Stand 6 into the top opening on the Leg Developer Holder Use a Lock Knob 86 to secure the Stand at desired height DIAGRAM 3 26 STEP 4 See Diagram 4 A Insert two Y 2 Bushings 52 into the holes on the Seat Bracket 5 and align the holes to the pivot on the Main Seat Support 1 B Attach the two Backrest Supports 10 to the Seat Bracket and align the holes Secure them with a M10 x 7 14 Allen Bolt 43 two 34 Washers 39 and one M10 Aircraft Nut 50 Do not over tighten the Nut and Bolt Make sure the Backrest Supports are able to swivel C Attach the Backrest Incline Support 7 to the opening on the Main Seat Support Use the T shaped Lock Pin 15 to secure the Backrest Incline Suppo
16. rt at the Last Hole on the end of Support D Attach the other end of the Backrest Incline Support 7 to the Backrest Supports 10 Align the holes and secure them with two M10 x 1 9 Allen Bolts 42 and two 3 4 Washers 39 STEP 5 See Diagram 5 A Place the Seat Pad 8 onto the Seat Bracket 5 Secure it with four M8 x 1 5 8 Allen Bolts 46 and Y 5 8 Washers 38 B Attach the Backrest Board 9 to the Backrest Supports 10 Secure it with four M8 x 1 5 8 Allen Bolts 46 and 5 8 Washers 38 C Attach the Arm Curl Pad 11 to the Arm Curl Bracket 23 Secure it with two M8 x 5 8 Allen Bolts 41 and Y 5 8 Washers 38 D Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand 6 Insert the M8 x 3 1 Allen Bolt 45 through the open track on the Arm Curl Stand and the holes on the Arm Curl Bracket and secure the Bolt with two 5 8 Washers 38 and one M8 Aircraft Nut 51 Do not over tighten the Nut and Bolt The Bolt needs to be able to slide on the track freely DIAGRAM 5 28 STEP 6 See Diagram 6 A Insert two Foam Tubes 16 halfway through the holes on Leg Developer 12 B Push four Vinyl Foam Rolls 27 onto the Tubes from both ends C Push four Foam Roll End Caps 31 into the ends D Attach the Arm Curl Handle 19 to the back holes on the Leg Developer Secure it with a Lock Pin 20 Attach the Abdominal Strap 24 to the front holes
17. t Bracket 30 M10 x 3 7 Allen Bolt 79 and Y 34 Washer 86 to the top hole Secure the bottom hole with one M10 x 3 4 Carriage Bolt 69 4 Washer 86 and M10 Aircraft Nut 83 F Attach the Upper Support Frames 9 to the Upper Frame 11 from each side Align the holes and secure them together with two M10 x 2 Carriage Bolts 72 34 Washers 86 and M10 Aircraft Nuts 83 G Securely tighten all Nuts and Bolts previously installed 11 DAIGRAM 3 a a ih SIN L e N STEP 4 See Diagram 4 A Attach the Butterfly Base 14 to the front of Rear Vertical Frame 6 Attach the Butterfly Pulley Bracket 15 to the back of the Rear Vertical Frame Align the holes and secure them with one M10 x 2 9 Carriage Bolt 72 Y Washer 86 and M10 Aircraft Nut 83 from the side Secure it with two M10 x 3 12 Allen Bolts 79 four 94 Washers 86 and two M10 Aircraft Nuts 83 from the back of Rear Vertical Frame B Insert the pivot on the Left Butterfly 20 into the hole on the Butterfly Base from the bottom Secure it with one Lock Ring 57 1 12 Washer 67 x 1 14 Allen Bolt 82 and M6 Aircraft Nut 85 C Attach the Butterfly Arm Pad 33 to the Left Butterfly Secure it with two M8 x 2 Le Allen Bolts 81 and Y 5 8 Washers 87 D Repeat Procedures B amp C above to install the other side DIAGRAM 4 CABLE LOOP DIAGRAM
18. warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal right You may also have other rights which vary from state to state Register on line at www impex fitness com IMPEX INC 14777 Don Julian City of Industry CA 91746 ORDERING REPLACEMENT PARTS Replacement parts can be ordered by calling our Customer Service Department toll free at 1 800 999 8899 during our regular business hours Monday through Friday 9 am until 5 pm Pacific standard time info impex fitness com When ordering replacement parts always give the following information 1 Model 2 Description of Parts 3 Part Number 4 Date of Purchase 32
Download Pdf Manuals
Related Search