iHome iH16 User's Manual
Contents
1. Install iPod Insert 3 Carefully place your iPod into the dock The iPod must not be in a case or skin Installing Replacing Batteries for Portable Operation The iH16 uses 4 AA batteries for portable operation The H16 will not charge your iPod while operating on batteries If sound becomes weak or distortea it is time to replace the batteries e Open the battery compartment cover located on the bottom of the unit e Insert 4 AA batteries as indicated e We recommend the use of alkaline batteries for longer life NOTE To save battery life when running on batteries unit will automatically power OFF after 3 minutes of non use no song playing Batteries information e Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries Charging Your iPod Note Please make sure you are using the correct side of the insert for your iPod model if needed see Install iPod Insert and that your iPod is properly docked into the iH16 1 While your iPod is docked in the unit and the unit is connected to AC power it recharges until fully charged iPod will not be overcharged Unit will not charge iPod when operating on batteries Listening to Your iPod 1 Dock an already playing iPod and the iH16 will automatically turn on You will hear the music playing from your iPod Note If the volume on the playing audio is too low on the iPod the H16 may not detect that the iPod is in play mode Press the2. Visit www ihomeaudio com 8 Trouble Shooting Symptom Possible Problem Solution Unit doesn t AC adaptor isn t plugged to a wall Plug the AC adaptor into a wall outlet and plug the respond outlet or the connector is not connector into the supply jack on the unit no power plugged into the power supply jack on the back of the unit Wall outlet is not functioning Plug another device into a wall outlet same outlet to confirm the outlet is working Batteries are weak dead Replace current batteries with fresh ones iPod does not Using no or wrong iPod insert Make sure the dock insert is the proper fit to your iPod dock properly Dock or connector is obstructed Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod Then reseat it in the dock j j Remove your iPod from the dock and check for iPod does not iPod is not docked properly obstruction on the connectors in the dock and on your respond to the iPod Then reseat it in the dock unit Your iPod software is too old Upgrade software on your iPod via iTunes eee Please refer to your iPod manual for details P lease make iPod is locked up sure your iPod is working properly before docking in the unit iPod doesn t Unit is operating on batteries not Unit will not charge iPod when running on batteries dharus connected to AC adaptor Connect unit to AC adaptor to charge iPod SEN j Remove your iPod from the dock and check for iPod is not dock
3. that objects do not fall and liquids are not spilled into any openings or vents located on the product Attachments Do not use attachments not recommended by the product manufacturer Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall sockets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Damage Requiring Service The unit should be serviced by qualified service personnel when A the power supply cable or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure C the unit has been exposed to rain D the unit has been dropped or the enclosure damaged E the unit exhibits a marked change in performance or does not operate normally Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cable should be unplugged from the unit to prevent damage or corrosion Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel Questions
4. Model iH16 Portable Alarm Clock Speaker o System for your iPod Questions Visit www ihomeaudio com Table of Contents Quick Start A iii ii io ii iii 1 Controls and Indicators 2 HO Display 232 23 92022 ostesrsarenessenenenennsro canes nani diossiisossicaiss 3 Install Clock Backup Battery 3 Using iH16 4 Charging your iPod stas torera 4 Listening to your iPod 4 Listening to non docking iPod or other audio devices 5 Setting Up the IH16 lona III III III TIT TIT TIT TT 5 Alarm Operation 6 Sleep Operation gt n 7 Snooze Dimmer Operation 7 A Consumer Guide to Product Safety 8 Trouble Shooting 2 rrr s r rrrrZZZKrMrMrMrMrWX RrRrRr r e a a na 9 Soluci n De Prob
5. Pod 4 time no insert needed for iPod Classic 160 GB iPod touch q i a 1 J 090 O a au a am iPod classic 80 120 GB e Press the DST On Off Button on the back of the unit as needed to add or subtract an hour for daylight saving or standard time e Press amp Hold the Clock Adj button on the back of the unit until the hour display flashes Press the or buttons to set the hour then press the Clock Adj button e Press the or buttons to set the minutes then press the Clock Adj button again to confirm time setting Controls and Indicators Front Panel Snooze Dimmer Button Silence alarm temporarily or adjust display brightness Up Plus Button Increase volume time setting Power Button Press to power unit ON or OFF Down Minus Button Decrease volume time setting Alarm Button Press and hold for Alarm Setting mode Back Panel DST On Off button Press to add or subtract 1 hour for daylight saving time Aux in Jack Connect aux audio source DC Jack Connect AC adptor Sleep Button Clock Adj Button Press for Sleep mode Press and hold for Clock Adjust mode iH16 Display gt r CI GD 3 Alarm Indicator pm iPod Indicator Sleep Indicator Battery Low Indicator PM Indicator Time Display Daylight Saving Time Indicator Install Clock Backup Battery The iH16 uses a CR2032 button cell battery to keep alarm and clock settings in the even
6. Press the or Button until the current minute is displayed 8 Press the Alarm Set Button during time setting to set 12 hour or 24 hour display format 4 Press the Clock Adj Button again to confirm the clock setting You should hear 2 beeps indicating the clock time is set 5 Press the DST on off Button located on the back of the unit to add one hour for daylight saving time on or to subtract one hour for standard time off The x icon will appear on the display to indicate DST is on Alarm Operation The iH16 Audio System for iPod features Sure Alarm Provided you have installed the 4 AA batteries if a power failure occurs or the AC adaptor is accidentally disconnected the alarm will still wake you up This unit also features Gentle Waking which gradually increases the volume of whatever alarm you set NOTE TO WAKE TO iPod YOUR iPod MUST BE PROPERLY DOCKED AND OFF NOT IN PLAY MODE OR NO iPod ALARM WILL SOUND You CANNOT wake to Line in audio devices Setting the Alarm 1 2 3 Press and hold the button until the hour display flashes Press the or Button until the desired alarm hour is displayed Remember to set the correct AM or PM time indicated by PM on the display there is no AM indicator Press the button again then press the or Button until the desired alarm minute is displayed Press the 0 button again to exit the setting mode You should hear 2 beeps indicating the alarm
7. anada Battery Warning For models that use Lithium batteries Lithium batteries can explode or cause burns if disassembled shorted recharged exposed to water fire or high temperatures amp not handled appropriately Do not place loose batteries in a pocket purse or other container containing metal objects do not mix with used or other battery types or store with hazardous or combustible materials Store in cool dry ventilated area Follow applicable laws and regulations for transport and disposal For models that require more than one battery Do not mix with used or other battery types brands Replace all batteries at the same time Do not open batteries Do not dispose of in fire e Do not heat above 75 C 167 F Do not expose contents to water Do not charge or recharge Do not install backwards Attach the AC adaptor cable to the jack on the back of the iH16 and plug the other end into a working wall socket See the table below to find which side of the dock insert matches your iPod model and place insert in dock NOTE iPod Classic 160 GB does not require the insert 1 Turn so correct insert face for your iPod 2 Slide insert downwards until it snaps into place Insert iPod into dock with proper insert iPod must not be in a skin or case iPod will charge while docked Press the power button on the iH16 to play the iPod i d dia Gala al all iPod nano models For this i
8. apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI Technologies product 2008 SDI Technologies Inc All rights reserved Questions Visit www ihomeaudio com or call 1 800 288 2792 Toll Free 1H16 061509 B 11 Printed in China
9. ca y elimine la obstrucci n correctamente obstruidos Vuelva a acoplar su iPod El iPod no se El iPod no est colocado Retire el iPod de la muesca y elimine la obstrucci n comunica con correctamente Vuelva a acoplar suiPod la unidad El software programa de su Actualice su programa v a iTunes iPod es obsoleto ve Verifique el correcto funcionamiento de su iPod antes de El iPod est trabado acoplarlo a la unidad Por favor refi rase al Manual del Usuario de su iPod para mayor informaci n El iPod no carga El iPod no est colocado Retire el iPod de la muesca y elimine la obstrucci n CC Vuelva a acoplar su iPod EliPod est trabado iPod est trabado Verifique el correcto funcionamiento de su iPod antes de La bater a del iPod tiene alg n acoplarlo a la unidad Por favor refi rase al Manual del problema Usuario de su iPod para mayor informaci n El sonido sale El nivel de volumen est alto Baje el nivel de volumen Apague la funci n EQ 3D Aedo La fuente de sonido est Si la grabaci n original de sonido del iPod o MP3 era de distorsionada mala calidad escuchar ruido distorsi n al ser amplificada mediante los parlantes de alta potencia Intente utilizar otra fuente de sonido como la m sica de un CD Si utiliza un iPod Shuffle o una fuente de sonido externa como un iPod de generaciones anteriores intente bajar el volumen del aparato en si Tambi n puede intentar reducir los bajos Las bater as
10. d button once to play iPod When the iPod is docked and in standby mode press the d button on the iH16 to play your iPod Press play pause on your iPod to pause play press again to resume it Press the or buttons on the iH16 to adjust the system volume To turn off the unit press the button on the iH16 Your iPod will continue charging while in the dock mB UN Listening to non docking iPod or other audio devices 1 Plug one end of an audio cable available at www ihomeaudio com into the headphone or line out jack on your device and the other end of the patch cord into the H16 Aux in J ack 2 Press the d button to turn the iH16 on 3 Press the or Buttons on the H16 to adjust the system volume You may need to adjust your device volume too 4 To turn off the iH16 press the d button Please remember to turn off your device too NOTE Do not connect and try to play an aux audio device while a docked iPod is playing or you will hear both Setting Up the iH16 Setting the Clock Time 1 Press and hold the Clock Adj Button for 2 seconds until the hour display flashes Press the or Button until the current hour is displayed Remember to set the correct AM or PM time a PM icon to the left of the time display is the PM indicator there is no AM indicator Note that the PM indicator will not appear when using 24 hour display mode 2 Press the Clock Adj Button again The minute display will flash
11. ed properly obstruction on the connectors in the dock and on your iPod Then reseat it in the dock iPod is locked up frozen Please refer to your iPod manual for details Please make iPod battery has problem sure your iPod is working properly before dock into the unit Sound is distorted Volume level is set too high Sound source is distorted If iPod original sound source is poor quality distortion and noise are easily noticed with high power speakers Try a different audio source such as a music CD Ifyou are using an iPod Shuffle or external sound source like older generation iPod try reducing the output volume on the device itself Also try reducing bass Batteries are weak dead Replace current batteries with fresh ones Solucionando Problemas S ntoma Causa Posible po Soluci n Cd La unidad no El adaptador de AC no ha sido Conecte el adaptador AC al tomacorrientes y el cable a la responde conectado a la corriente el ctrica ficha de entrada de la unidad no enciende o el cable no ha sido conectado a la parte posterior de la unidad El tomacorrientes no funciona Conecte otro aparato al mismo tomacorrientes para verificar si se encuentra activo Las bater as est n gastadas Reemplace las bater as EliPod no El encastre no es el correcto o no Verifique tener el encastre correspondiente antes de encastra ha colocado encastre alguno intentar acoplarlo al aparato La muesca o el encastre estan Retire el iPod de la m ye
12. est n gastadas Reemplace las bater as 10 Limited 90 Day Warranty Information iHome Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 90 days from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charge except for a 10 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service without proof of purchase is 25 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statemen
13. is set Note Once you set the alarm time the alarm will be automatically armed indicated by the icon To disarm the alarm press the button The 0 icon will disappear and the alarm will not sound at the set time Note Make sure to adjust volume level for a comfortable wake up volume 4 When the alarm is sounding the 10 icon will flash To snooze during the alarm press the Snooze Dimmer Button The alarm will be silenced for 9 minutes then come on again e To turn the alarm off and reset it to come on the next day press the Button If the alarm is not turned off once it sounds it will play for one hour then turn off automatically This cycle will repeat every 24 hours unless the controls are changed Note Please make sure your iPod has enough songs to play for one hour otherwise please set the iPod repeat mode to ON Note If there is no iPod present or there is no music detected on the iPod at alarm time the iH16 will automatically switch to buzzer alarm Sleep Operation 1 2 3 4 5 When the iH16 is off or while listening to your iPod press the Sleep Button to enter sleep mode The Sleep Icon will appear on the display to indicate it is in sleep mode Sleep mode has a Gentle Sleep feature which gradually lowers the volume before it shuts off You can adjust the sleep timer from 90 60 30 or 15 minutes by pressing the Sleep Button again The unit will automati cally turn off after the selec
14. lemas 10 Warranty Information eraser a RR IES IE IR EEE 11 Maintenance e Place the unit on a level surface away from sources of direct sunlight or excessive heat e Protect your furniture when placing your unit on a natural wood and lacquered finish A cloth or other protective material should be placed between it and the furniture Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzine thinner or similar materials can damage the surface of the unit NOTE Be careful not to touch the surface of the speakers at either end of the unit Getting Started Thank you for purchasing the iHome iH16 Audio Speaker System for your iPod Designed specifically to work with your iPod this system provides high quality audio performance that brings out the best in your music Please read this instruction book carefully before operating the iH16 and keep it for future reference Check for iPod compatibility iH16 is an advanced system and supports most updated iPod features To make sure your iPod works properly with iH16 please update your iPod firmware with the latest version via iTunes FCC Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept a
15. ny interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du C
16. t or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies for the sum of 10 00 25 00 without proof of purchase 4 Send the unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc 1330 Goodyear Drive El Paso TX 79936 6420 Disclaimer of Warranty NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI Technologies or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemplary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not
17. t of a power failure and 4 AA batteries to maintain alarm operation If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally disconnected the display backlight will not remain lit but current time and alarm time settings will be temporarily maintained Otherwise you must reset the time and alarm settings If 4 AA batteries are installed alarm will operate when unit is not connected to AC adaptor 1 Please make sure the AC adaptor is connected Otherwise all settings may be lost during battery replacement 2 Open the backup battery compartment door located on the backside of the unit 3 Insert one CR2032 button cell battery checking that the polarity and sides of the battery matches the drawing in the battery compartment Installing Backup Battery Close the compartment door Note Make sure you dispose of batteries properly see your local regulations Note All keys have no function if only back up battery installed Install AC Adaptor Connect the AC adaptor cable plug into the jack on the back of the ih16 then plug the AC adaptor into the wall outlet Install iPod Insert Your H16 comes with a double sided insert to ensure certain iPod models fit properly in the dock To place an insert 1 Identify the side of the insert that matches your iPod model see table on page 1 2 Gently press the iPod insert into the dock with the proper side facing the connector pins
18. ted time When the display changes back to show the real time pressing the Sleep Button once will show the sleep time remain ing Pressing it again will change the sleep time to the next lowest increment The iH16 has an independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the alarm volume Press the and Buttons to adjust the sleep volume The sleep volume will remain at that level the next time you enter sleep mode until controls are changed To stop listening at any time press the icon to turn unit off Snooze Dimmer Operation ie N Press the Snooze Dimmer Button after the alarm sounds The alarm will go off and will come on again in about 9 minutes You may repeat this cycle several times during the one hour alarm cycle During normal operation with the AC adaptor press the Shooze Dimmer Button to control the brightness high medium low and off of the LCD display During portable operation with 4 AA batteries the LCD backlight will display for about 5 seconds when you press the Snooze Dimmer Button once A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instr
19. uctions handy for future reference Take special note of all warnings listed in these instructions and on the unit le 2 10 11 12 13 Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet which may impede the flow of air through the ventilation openings Heat The unit should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Power Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions Objects and Liquid Entry Care should be taken so
Download Pdf Manuals
Related Search