iHome iD99 User's Manual
Contents
1. 2 Monitor the charging status on your device If it does not appear to be charging try moving the USB Mode Switch on the unit to the other position NOTE While the USB port should charge the majority of devices some makers use proprietary standards and their devices may not charge If this occurs use the charger that came with the device Replacing Clock Back up Battery The unit comes with 1 CR2450 back up battery installed to provide continuous alarm operation and clock settings in the event of a power failure Remove the battery pull Replacing Backup Battery tab before use When the Battery Low Icon located on the lower right of the display is flashing it is time to replace the back up battery The battery compartment is located on the bottom of the unit 1 Please make sure the AC adaptor is connected otherwise all settings may be lost during battery replacement 2 Use a Phillips screwdriver to remove the battery compartment cover located on the bottom of the unit Remove the exhausted battery 3 Insert 1 CR2450 battery checking that the side is facing you Replace the compartment door Note Make sure you dispose of battery properly see your local regulations WARNING Lithium batteries can explode or cause burns if disassembled shorted recharged exposed to water fire or high temperatures Do not place loose batteries in a pocket purse or other container containing metal objects mix with used or other2. or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI Technologies or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemplary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI Technologies product 2011 SDI Technologies Inc All rights reserved Questions Visit www ihomeaudio com or call 1 877 446 6301 Toll Free iD99 0401612 A Printed in China
3. battery types or store with hazardous or combustible materials Store in cool dry ventilated area Follow applicable laws and regulations for transport and disposal 7 IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 Water and Moisture The unit should not be used near water For example near a bathtub washbowIl kitchen sink laundry tub swimming pool or in a wet basement 2 Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet which may impede the flow of air through the ventilation openings 3 Heat The unit should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat 4 Power Sources The unit should be connected to a power supply only of the type described in the operating instruction
4. do not have an insert for your iPhone iPod you can safely dock it provided you always do so gently and carefully To purchase an insert visit www ihomeaudio com or call iHome toll free at 1 877 446 6301 to purchase one 3 Setting Clock with AutoSync 2 docking your iPad iPhone iPod Dock 1 Select the insert for your iPhone or iPod and place in Dock 1 Gently dock your iPhone or iPod You can safely dock your iPhone or iPod without an insert provided you use care Dock 2 Gently dock your iPad iPhone or iPod onto the flexible 30 pin dock on Dock 2 The devices docked in Dock 1 and Dock 2 will charge while docked Press the Dock 1 gt il or Dock 2 Pll Button on the unit to play your iPad iPhone or iPod iPhone 4 nano 6G touch 4G sert 19 insert nano 6G iPod touch 4G m7 NJ D Dock your iPad iPhone or iPod see step 2 The unit will Press and release the Mode Button as needed to select FM attempt to autosync to the time on your iPad iPhone or iPod band Press and release the or Button to tune in a station This process takes about 3 seconds See page 5 for programming presets Setting Up the Unit Connecting the Unit to Power Source Connect the AC adaptor cable plug into the DC jack on the back of the system then plug the AC cord of the AC adaptor into the wall outlet Adaptor must be plugged in to operate unit The unit does not operate on battery a battery back up system maintains clock settings during powe
5. operate the equipment e NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Maintenance e Place the unit on a level surface away from sources of direct sunlight or excessive heat e Protect your furniture when placing your unit on a natural wood and lacquered finish A cloth or other protec
6. Model iD99 Dual Dock Dual Alarm Stereo System for iPad iPhone or iPod Note Apps are not covered in detail in this booklet To learn more about how apps can enhance your experience please visit the App Store Questions For latest instructions visit www ihomeaudio com support LELI We mM Oko aii Val it Controls and Indicators Displayssan cniidec Ai ate eins ee Rs EE hn A ed ee ee 1 MUNG SLANE een E e E r E A E S a aS 2 Setting Up the Unit 245 04 een e aa a lei kee E E i a ei 3 Using TS AAI secie ene bet thats eE a a at ees bbc ccna tc tencqueety E E avesacuieceenetly aro EE 4 Listening to iPad iPhon iPod Listening to RadiOir ruranan nsec ecnntin nel tines EEEE ieee 5 Using the Unit in Other Countries Listening to other portable audio devices Sleep Operation ce eeeeeeeeeetteeenees 6 Nap Operation Dimmer Operation USB Charging Replacing Clock Backup Battery A Consumer Guide to Product Safety Trouble Shooting eee Warranty Information FCC Information This device complies with Part 15 of the FCC Rules operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation e Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to
7. The month and date will flash Press and release the or Button until the current month and date is displayed 5 Press and release the Clock Button once more Two beeps will sound to confirm your settings and you will exit Time and Calendar Setting mode Using the Alarms This unit has a dual alarm system so you can set two separate alarms to different alarm times wake to sources and schedules daily weekdays or weekend Tip Download the free iHome Set app for advanced alarm snooze and sleep functions Setting the Alarms Note Alarm 1 and Alarm 2 are set the same way Alarm Button below means the button Alarm 1 or Alarm 2 for whichever alarm you are setting 1 Press and hold the Alarm 1 or Alarm 2 Button until the alarm time flashes on the lower part of the display Press and release the or Button to set the alarm time press and hold for faster setting Remember to set the correct AM or PM time 2 Press and release the Alarm Button again to confirm the set alarm time then press and release the or Button to set the alarm schedule wake 7 days the whole week wake weekday Monday through Friday wake weekend Saturday and Sunday only 3 Press and release the Alarm Button again then press and release the or Button to select an alarm source to wake to Dock 1 Dock 2 Radio or Buzzer For wake to Dock 1 or Dock 2 Select Dock 1 or Dock 2 to wake to a docked iPad iPhone or iPod in Dock 1 or an
8. ce between the unit and synced iPad iPhone iPod To adjust autosync settings Press and hold the Clock Button located on the top of the unit for 2 seconds AUTOSYNC ON flashes on the display and a beep sounds To turn autosync off press and release the or Button while AUTOSYNC ON is flashing until AUTOSYNC OFF appears This will disable autosync and allow you to set the time manually see below Setting Time and Calendar Manually Autosync must be OFF to set the clock manually 1 Press and hold the Clock Button located on the top of the unit until AUTOSYNC ON or AUTOSYNC OFF flashes on the display if AUTOSYNC ON appears press the or Button to toggle to AUTOSYNC OFF setting 2 Press and release the Clock Button The time display will flash Press the or Button to adjust the time hold for a few seconds to advance or reverse rapidly Remember to set the correct AM or PM hour An icon in the upper left hand corner of the time display indicates AM or PM Note if you wish to change the time display from the 12 hour format to the 24 hour format sometimes called military time press and release either the Alarm 1 Button or Alarm 2 Button to switch between 12 hour and 24 hour display formats 3 Press and release the Clock Button again The year will flash in the lower part of the display Press and release the or Button until the current year is displayed 4 Press and release the Clock Button again
9. ct without charge except for a 25 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service without proof of purchase is 60 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies for the sum of 25 00 60 00 without proof of purchase 4 Send the unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc 1330 Goodyear Drive El Paso TX 79936 6420 Disclaimer of Warranty NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets
10. dicators Alarm time or source selected for alarm 2 not Make sure to set the alarm time and source for the alarm icon 1 or 2 alarm 1 or vice versa that is shown on the clock display Wake schedule setting is not correct 7 days is every day alarm weekday is Mon Fri and weekend is Sat Sun See page 4 for setting alarms Calendar is not set correctly which can affect See page 3 for setting Clock Calendar Section wake schedule alarm operation USB charging doesn t Device may not be connected properly or Check that your USB cable is the correct kind for your device and that it work may require special circuit is correctly connected to the unit and to your device Try switching the US B Mode Switch from the A or B position to its opposite If this fails use the charger that came with your device 10 Limited 1 Year Warranty Information iHome Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 1 Year from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this produ
11. e Button after the alarm sounds The alarm will be silenced and come on again 9 minutes later or at the custom minute interval you set Snooze can be pressed several times during the 1 hour alarm cycle Sure Alarm The unit has a sure alarm feature so the buzzer alarm still sound in the event of a power failure if the backup battery is installed see page 7 If your iPad iPhone iPod has no sound for 35 seconds or is not present the unit will switch to buzzer alarm automatically Listening to iPad iPhone or iPod The unit has two docks each with separate Play Pause controls Dock 1 is for iPhone or docking iPod models Dock 2 is for all iPad iPhone and docking iPod models Inserts are provided for docking popular iPhone and iPod models in Dock 1 While inserts provide the best stability you can safely dock your iPhone or iPod without an insert provided you always do so gently and carefully If you prefer to use an insert and do not have one for your model please contact customer service at 1 800 288 2792 to purchase one 1 Dock an already playing iPad iPhone or iPod The unit will automatically turn on and you will hear the audio playing from your iPad iPhone iPod Note If the audio source volume is too low on the iPad iPhone iPod the unit may not detect that the iPad iPhone iPod is in play mode If so pressing the Dock 1 or Dock 2 Pll Button should make the device in the related dock play 2 When the iPad iPhone iPod is docked and i
12. he unit exhibits a marked change in performance or does not operate normally 12 Antenna Do not connect an external antenna to the unit other than that provided 13 Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cable should be unplugged from the unit to prevent damage or corrosion 14 Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel Questions Visit www ihomeaudio com or call 1 877 446 6301 Toll Free 8 Troubleshooting Symptom Possible Problem Unit does not turn on AC adaptor isn t plugged into a working wall Plug the AC adaptor into a working wall socket and plug the connector socket or not plugged into the power supply into the supply jack on the unit jack on back of the unit Unit doesn t respond Unit requires a reset If unit is plugged in and doesn t respond try resetting the unit by following these steps a remove iPad iPhone iPod from dock b unplug unit from power source c remove back up battery d wait a few minutes then restore battery and resume use iPad iPhone iPod is not docked properly Remove your iPad iPhone iPod from the dock and check for obstruction on the connectors in the dock and on your iPad iPhone iPod Then reseat it in the dock Battery Lo
13. iPhone or iPod in Dock 2 Once Dock 1 or Dock 2 is selected press and release the or Button to select Normal plays the last played song or select Playlist to wake to a custom playlist NOTE you must create a playlist named iHome in iTunes and have it on your iPad iPod iPhone The unit will play music randomly from within the iHome playlist If no playlist is detected the unit will play the last song played instead If the unit does not detect an iPad iPhone iPod at the set alarm time the unit will default to buzzer alarm The alarm cycle lasts for one hour make sure you have enough music on your iPad iPhone or iPod to last that long For wake to radio after selecting Radio as the wake to source press and release the Alarm Button and then press and release the or Button to select a radio station or press and release the Presets Button as needed to select a stored preset radio station to wake to see Listening to Radio on page 5 for details on setting radio stations as presets 4 Press and release the Alarm Button again then press and release the or Button to set the alarm volume 5 Press and release the Alarm button again or no button within 10 seconds Two beeps will confirm setting is complete and you will exit the alarm setting mode The alarm will be armed once set and the corresponding alarm icon will light up The lower part of the display will show the earliest set alarm time Reviewing Arming and Disarming Alar
14. m Turn Alarm Function On and Off Alarms are automatically armed when set Active alarms are indicated by alarm icons on the display 1 Once an alarm is armed the lower part of the display will show the alarm time If more then one alarm is armed the earliest alarm time will show 2 To review the alarm time press an alarm button once The related alarm time and wake source will show on the lower part of the display 3 During alarm review press and release the Alarm Button once to toggle it on or off If the alarm is armed the related alarm icon will light up Resetting the Alarm to Come on the Next Day 1 When the alarm is sounding press and release the Power Button Wakeup Button Alarm 1 or Alarm 2 Button to stop the alarm and reset it to come on the next set day For example if alarm is set for weekdays and you reset the alarm on Friday the alarm will come on again on Monday not Saturday TIP When the iHome Sleep app is running press the wakeup button to access wake profiles When the app is not running you can press the wakeup button to shut off the unit and reset the alarm to come on at the set time Snooze 1 To program a custom snooze time press and hold the Snooze Button during normal operation when alarm is not sounding until the snooze minutes display appears Press and release the or Button to set the snooze time from 1 to 29 minutes TIP You can also adjust snooze time with the iHome Set app 2 Press the Snooz
15. n standby mode press the Pil Button on the unit to play the iPad iPhone iPod If the unit is already on press and release the Mode Button as needed until DOCK 1 or DOCK 2 appears on the lower part of the display indicating the unit is controlling Dock 1 or Dock 2 If your iPad iPhone or iPod touch is in video mode you may see the locked slider on your iPad iPhone iPod display If so you will need to unlock your iPad iPhone iPod 3 Press the Dock 1 or Dock 2 PII Button on the unit to pause play in that dock press again to resume play 4 Press the or Button on the unit to go to the next or previous track Press and hold while track is playing for high speed forward or reverse music search of the current track Adjusting Sound on the Unit You can adjust the sound on the unit while listening to any sound source 1 Press the or 4 Button on the unit to adjust the system volume 2 Press and release the EQ Button as needed to select Treble Bass Balance or 3D sound effect then press the or Button to adjust settings TIP You can also adjust EQ with the iHome Set app Listening to Radio Setting up the Antenna Extend FM wire antenna fully for best reception Do not strip alter or attach to other antennas Tuning and Playing the Radio 1 Press and release the Mode Button as needed to turn on the unit and cycle through Dock 1 Dock 2 FM radio and Aux in modes 2 Once FM mode is selected press the or But
16. nd release the or Button to set the xxx to your region 2 Press and release the Mode Button again or no button within 10 seconds to exit the radio frequency setting mode Two beeps will confirm radio frequency setting Listening to other portable audio devices You can play an MP3 player or other portable audio device through the iD99 via the Aux in Jack 1 Plug one end of a stereo audio patch cord available at http www ihomeaudio com into the headphone or line out jack on your device and the other end of the patch cord into the iD99 Line in Jack located on the back of the unit 2 Press and release the Mode Button as needed until Aux in appears in the lower part of display indicating Aux in playing mode 3 Turn on and play your device 4 Press the or Button on the unit to adjust the system volume You may need to adjust your device volume too 5 Press the Power Button to turn off the unit Remember to turn off your device too Sleep Operation Sleep mode lets you sleep to iPad iPhone iPod or the radio gradually lowering the volume until the unit shuts off at the selected time 1 Press the Bedtime Button to enter sleep mode The Sleep Icon will appear on the display to indicate sleep mode Sleep mode has a Gentle Sleep feature which gradually lowers the volume The unit will automatically turn off after the selected sleep time You can adjust the sleep timer from 120 90 60 30 15 minutes or OFF by p
17. ock and check for obstruction didn t charge up on the connectors in the dock and on your iPad iPhone iPod Then reseat it in the dock iPad iPhone iPod is locked up frozen Please make sure your iPad iPhone iPod is working properly before docking into the unit Please refer to your iPad iPhone iPod manual for iPad iPhone iPod battery has problem details Time sync didn t work Older iPod models such as iPod mini do not Make sure you are using an iPhone or newer iPod such as touch support time sync function nano or classic If not available set time manually see page 3 Troubleshooting Symptom Possible Problem Solution Sound is distorted Volume level is set too high Decrease the volume Sound source is distorted If the iPad iPhone iPod original sound source MP3 is old or of poor quality distortion and noise are easily noticed with high power speakers Try a different file from a trusted source such as iTunes If you are using an external sound source try reducing the output volume on the device itself Also try turning bass boost OFF EQ settings are too high Lower EQ settings Unit adaptor gets This is normal Turn unit off for awhile or lower volume warm after extended play at high volume Snooze time Custom snooze time not set Press and hold Snooze button then press or Button to adjust is too long short Alarm not working AM PM time alarm time not set correctly When setting clock or alarm time take note of the AM PM in
18. r failures Updating your iD99 firmware For best performance make sure to update the iD99 firmware To do so download the free iHome Set app from the App Store Launch the app scroll to Search for Update then follow directions to update the firmware Note Please use Dock 2 for firmware update Turning the Unit ON or OFF Press the Power Button on the unit at any time to turn the unit On or Off Note that a docked iPad iPhone or iPod will continue to charge when the unit is turned off as long as the AC adaptor is plugged in Setting the Clock Time Using AutoSync The AutoSync feature automatically syncs the time setting on the unit to the time on your iPad iPhone or recent model iPod iPod touch iPod nano and iPod Classic older iPod models such as iPod mini do not support this feature AUTOSYNC SETTING By default the unit is set to AUTOSYNC ON mode and will attempt to autosync the time whenever a capable iPhone or iPod is docked in Dock 1 OR an iPad iPhone or iPod is docked in Dock 2 1 Dock your iPad iPhone or recent model iPod in the unit In about 3 seconds the unit will sync to your device 2 The unit will now autosync every time a capable iPhone iPod or iPad is docked NOTE iPhone time is automatically updated to the correct time via cell phone towers The time on your iPad or iPod is accurate only to the time on the computer the last time the iPad iPod was synced to it It s possible to have up to 59 seconds differen
19. ressing the Bedtime Button again When the display changes back to show the real time pressing the Bedtime Button once will show the sleep time remaining Pressing it again will change sleep time to next lowest increment ID99 has independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the alarm volume Press the or Button on the unit to adjust the system sleep volume The sleep volume will remain at that level the next time you enter sleep mode until controls are changed To stop listening at any time press the Power Button on the unit to turn it off 6 woh A oa Nap Operation Nap mode lets you set an alarm separate from the Alarm 1 and Alarm 2 settings The nap wake to source by default is the buzzer alarm 1 Press the Nap Button located on the top of the unit as needed to adjust the nap timer for 5 10 15 20 30 45 60 90 or 120 minutes or OFF 2 The nap time remaining will appear on the display as the time diminishes Pressing the Nap Button again will change nap time to the next highest setting Dimmer Operation During normal operation press the Snooze Dimmer Button to control the brightness of the LCD display USB Charging The unit has a USB charging port located on the back of the unit 1 To charge your device connect one end of a USB charging cable not included into the USB charging port on the unit and the other to your device s charging port
20. s or as marked on the appliance 5 Power Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket 6 Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions 7 Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product 8 Attachments Do not use attachments not recommended by the product manufacturer 9 Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges 10 Overloading Do not overload wall sockets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 11 Damage Requiring Service The unit should be serviced by qualified service personnel when A the power supply cable or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure C the unit has been exposed to rain D the unit has been dropped or the enclosure damaged E t
21. tive material should be placed between it and the furniture e Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzene thinner or similar materials can damage the surface of the unit Controls and Indicators Top Panel Rubberized device rest Dock 2 Flexible 30 pin connector for iPad iPhone iPod SS ae ee 30 pin connector o or iPhone or iPo Dock2 iPad iPhone iPod Presets Button EQ Button Clock Button Bedtime Button Power Button Nap Button Alarm 1 Button Alarm 2 Button Sa Wakeup Button 6 Set Button Taman skip search FWD REV Mode Button Snooze Dimmer Button Dock 1 Play Pause Button Dock 2 Play Pause Button Bottom Panel Lower raise volume Button T Rear Panel AC Adaptor Jack USB port USB Mode Switch FM Antenna Backup Battery Compartment Door Line in Jack Display Time Display a amma am aa 7 PM Indicator GOGH A Fi Fe Alarm Indicators Ee E E oan AM Indicator coli A J l iHome App Indicator r ba r A Battery Low Indicator l a NOTE AM PM indicators will not appear Radio Alarm Time iPod Display when clock is set to 24 hour display mode Attach AC adaptor cable to DC jack on back of the unit and plug the other end into a wall socket Remove pull tab from the backup battery compartment on the bottom of the unit NOTE Inserts provide the best stability for your iPhone or iPod If you
22. ton to tune the radio to a desired station The current radio frequency appears in the lower right of the display Press the or Button for a few seconds to scan for the next clear station 3 To memorize a station as a preset A Press the Presets Button as needed to step through the 6 presets P1 P6 to the number you wish to assign and then hold the Presets Button until the selected preset number begins flashing in the display B Press the or Button to tune the radio to a desired station Hold briefly to have the radio autoscan search for the next clear station C Press the Presets Button to confirm the setting two confirmation beeps will confirm the setting and the preset number you wish to assign Repeat steps A C to preset up to 6 stations 4 To listen to a preset station at any time press the Presets Button to choose the desired preset 5 Press the or Button on the unit to adjust the system volume 6 Press the Power Button to turn off the unit Using the Unit in Other Countries Different regions of the world use different FM radio frequency steps and ranges You will need to select the one that matches the standards in your region USA EUROPE JAPAN AUSTRALIA or CHINA The default setting is USA if you live in the US you may skip this section 1 Make sure the unit is OFF not playing in any mode Press and hold the Mode Button for about 5 seconds until Radio xxx appears in the lower part of display Press a
23. w icon Battery is weak Replace with new battery always flashing Battery was not installed properly Check to make sure the side is facing outwards iPad iPhone iPod does iPad iPhone iPod is not docked properly Remove your iPad iPhone iPod from the dock and check for obstruction not respond to the on the connectors in the dock and on your iPad iPhone iPod Then reseat unit iPad iPhone iPod it in the dock 1S play ing but Sa Your iPad iPhone iPod software is too old Upgrade software on your iPad iPhone iPod via iTunes on your computer iPad iPhone iPod is locked up plays but no Check the volume setting Make sure your iPad iPhone iPod is working sound comes out properly before docking into the unit Please refer to your iPad iPhone iPod manual for details See above for software upgrade information You may need to reset your iPad iPhone iPod Refer to your iPad iPhone or iPod user guide for details on how to perform a reset Using 1St or 2nd generation iPod iPod Shuffle Unit cannot control those iPod models or other devices or other devices Unit iPad iPhone iPod The unit is reacting to external interference Move unit away from potential sources of external interference such as performance is erratic computers modems wireless devices routers or fluorescent light No sound from unit Volume is set too low on unit Make sure volume is turned up iPad iPhone iPod iPad iPhone iPod is not docked properly Remove your iPad iPhone iPod from the d
Download Pdf Manuals
Related Search