Icom iF14/S User's Manual
Contents
1. 3 E Turning power ON Rotate VOL to turn power ON E Channel selection IC F14S F24S Toggle CHANNEL SWITCH to select the channel 1 or 2 or push one of MR CH 1 to MR CH 4 key to select a chan nel directly The memory channels 3 and 4 are avail able when MR CH 3 and MR CH 4 keys are assigned CHANNEL SWITCH IC F14 F24 Rotate CHANNEL SELECTOR to se lect the desired operating channel in se quence or push one of MR CH 1 to MR CH 4 key to select a channel di rectly CHANNEL SELECTOR AUTOMATIC SCAN TYPE Channel setting is not necessary for this type When turning the power ON the transceiver automatically starts scanning Scanning stops when receiving a call CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 E Call procedure When your system employs tone signalling excluding CTCSS and DTCS the call procedure may be necessary prior to voice trans mission The tone signalling employed may be a selective calling system which allows you to call specific station s only and prevent unwanted stations from contacting you D Select the desired TX code channel or 2 5 tone code according to your System Operator s instructions This may not be necessary depending on programming Push the call key assigned to one of the dealer programmable keys p 11 After transmitting a 2 5 tone code the remainder of your com munication can be carrie2. An AC adapter may be supplied with BC 119N depending on ver sion or the DC power cable OPC 515L CP 17L AC adapter Not supplied with Some versions adapter is installed in BC 119N Optional OPC 515L for 13 8 V power source or CP 17L for 12 V cigarette lighter socket can be used instead of the AC adapter IMPORTANT Ensure the guide lobs on the bat tery pack are correctly aligned with the guide rails inside the charger adapter Guide rails BATTERY CHARGING 5 Rapid charging with the BC 121N AD 106 The optional BC 121N allows up to 6 battery packs to be charged simultaneously The following items are additionally required Six AD 106 An AC adapter BC 124 or the DC power cable OPC 656 TRANSCEIVER BP 231 AD 106 charger adapters are installed in each slot AC adapter Purchase separately IMPORTANT Ensure the guide lobs on the bat tery pack are correctly aligned with the guide rails inside the charger adapter Guide rails V DC power cable OPC 656 Connect with the DC power supply 13 8 V at least 7 A NN ee es ee E 6 SWIVEL BELT CLIP SWIVEL BELT CLIP 6 a MB 93 contents 3 Clip the belt clip to a part of your belt And insert the transceiver into the belt clip until the base clip inserted fully into the groove Qty 1 Belt Clips 3 5 edo ete de ac i e ER prepa es 1 iBase Clip ove hey rtt e e e EE
3. The selected channel is a receive only channel Time out timer After continuous transmission for the pre programmed time period the time out timer activates and causes the transceiver to stop transmit ting Penalty timer Once the time out timer activates transmission is further inhibited for a period determined by the penalty timer o DTMF transmission If the transceiver has DTMF Autodial assigned to it the automatic DTMF transmission function is available Push DTMF Autodial to transmit the DTMF code 3 CONVENTIONAL OPERATION B Scrambler function The optional voice scrambler units UT 109 01 and UT 110 01 provide high performance private communication between stations with the same scrambler codes Push and hold Scrambler to turn the scrambler function ON e Push Scrambler to turn the scrambler function OFF E Setting the squelch level The squelch circuit mutes the received audio signal depending on the signal strength While pushing PTT and Lower rotate VOL to turn the power ON to enter the squelch level adjust ment mode Push Upper to increase the Upper 3 squelch level tight squelch or Lower to decrease the squelch level loose squelch Rotate VOL to turn the power OFF to fix the squelch level Lower CONVENTIONAL OPERATION 3 E Man Down Emergency Call The man down emergency call function transmits an emergency call automatically after t
4. SP 13 EARPHONE Provides clear receive audio in noisy environment HM 131L sPEAKER MICROPHONE Combination speaker microphone that provides convenient oper ation while hanging the transceiver from your belt HM 131L has a moisture proof construction HS 94 HS 95 HS 97 HEADSET VS 1L vox PTT CASE HS 94 Ear hook type HS 95 Neck arm type HS 97 Throat microphone VS 1L VOX PTT switch box for hands free operation etc e FA SC73US FA SC56VS FA SC57VS sTUBBY ANTENNAS FA SC73US 450 490 MHz FA SC56VS 150 162 MHz FA SC57VS 160 174 MHz FA SC25U FA SC57U FA SC72U FA SC25V FA SC55V ANTENNAS FA SC25U 400 430 MHz FA SC57U 430 470 MHz FA SC72U 470 520 MHz FA SC25V 136 155 MHz FA SC55V 146 174 MHz Some options may not be available in some countries Please ask your dealer for details MEMO MEMO Count on us A 6369D 1EX Printed in Japan Icom Inc 2004 Icom Inc 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan
5. charged fully charge the battery pack again If the battery pack still does not retain a charge or very little a new battery pack must be purchased 5 BATTERY CHARGING E Optional battery chargers Rapid charging with the BC 160 The optional BC 160 provides rapid charging of optional Li lon bat tery packs An AC adapter may be supplied with BC 160 depending on ver sion or the DC power cable OPC 515L CP 17L is additionally required AC adapter BP 231 lt TRANSCEIVER Not supplied with mi some versions SN Optional OPC 515L gt for 13 8 V power source or CP 17L for 12 V cigarette lighter socket can be used instead of the AC adapter IMPORTANT Ensure the guide lobs on the bat tery pack are correctly aligned with the guide rails inside the charger adapter Guide rail AD 106 installation D Install the AD 106 desktop charger adapter into the holder space of the BC 119N 121N Desktop A adapter BATTERY CHARGING 5 Connect the plugs of the BC 119N BC 121N to the AD 106 with the connector then install the adapter into the charger with the supplied screws Screws supplied with the charger adapter 5 BATTERY CHARGING Rapid charging with the BC 119N AD 106 The optional BC 119N provides rapid charging of optional Li lon battery packs The following items are additionally required One AD 106 purchase separately
6. and 4 are available for IC Z F14S F24S when MR CH 3 and MR CH 4 keys are assigned j 2 PANEL DESCRIPTION MONITOR KEY e Mute and release the CTCSS DTCS or 2 tone squelch mute Open any squelch deactivate any mute while pushing this key LMR operation only Activates one of or two of the following functions on each chan nel independently PMR operation only Push and hold to un mute the channel audio is emitted Audible condition Push to mute the channel sets to Inaudible only Push to un mute the channel sets to Audible only Push after the communication is finished to send a reset code Z NOTE The un mute condition Audible condition may auto A matically return to the mute condition Inaudible condition A after a specified period LOCK KEY Push and hold to electronically lock all programmable keys except the following Call incl Call A and Call B Moni Audi and Emergency keys OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently de pending on the pre setting Ask your dealer for the output power level for each selection TALK AROUND KEY w Push to turn the talk around function OFF Push and hold to turn the talk around function ON The talk around function equalizes the transmit frequency to the re ceive frequency for transceiver to transceiver communication WIDE NARROW KEY Push to select the IF bandwidth
7. charger depending on versions Charging time approx 2 hours when BP 231 is attached e BC 121N wurri cHARGER AD 106 CHARGER ADAPTER 6 pcs BC 124 ac ADAPTER For rapid charging of up to 6 battery packs six AD 106 s are re quired simultaneously An AC adapter should be purchased sep arately Charging time approx 2 hours when BP 231 is attached e BC 160 DESKTOP CHARGER BC 145 ac ADAPTER For rapid charging of battery packs An AC adapter is supplied with the charger depending on versions Charging time approx 2 hours when BP 231 is attached OPTIONAL UNITS UT 108 DTMF DECODER UNIT Provides pager and code squelch capabilities UT 109 01 UT 110 01 SCRAMBLER UNITS Non rolling type UT 109 Rolling type UT 110 voice scrambler unit provides higher communication security UT 113 MAN DOWN UNIT Provides a measure of safety when working in a hazardous envi ronment etc options 7 o BELT CLIPS MB 93 swivEL BELT CLIP MB 94 BELT CLIP Exclusive alligator type belt clip The same as supplied with the transceiver MB 96 96F LEATHER BELT HANGER MB 93 s base clip is required DC CABLES CP 17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket For BC 119N OPC 515L OPC 656 pc POWER CABLES Allows charging of the battery pack using a 13 8 V power source instead of the AC adapter OPC 515L For BC 119N OPC 656 For BC 121N OTHER OPTIONS
8. 1 E To attach D Release the battery pack if it is attached p 3 Slide the base clip in the direction of the arrow until the base clip is locked and makes a click sound 6 swivEL BELT CLIP swivELBELT CLIP 6 E To detach D Turn the transceiver upside down in the direction of the arrow 2 Release the battery pack if it is attached p 3 and pull out from the belt clip Pinch the clip Q9 and slide the base clip in the direction of the arrow deep CAUTION HOLD THE TRANSCEIVER TIGHTLY WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged WAAR 5 m OPTIONS BATTERY PACK e BP 230 Li lon BATTERY PACK 7 4 V 800 mAh Li lon battery pack allows approx 5 5 hours op eration e BP 231 Li lon BATTERY PACK 7 4 V 1150 mAh Li lon battery pack allows approx 8 hours op eration The same as supplied with the transceiver e BP 232 Li lon BATTERY PACK 7 4 V 2000 mAh Li lon battery pack allows approx 14 hours op eration Typical operation Tx Rx Stand by duty cycle 5 5 90 CHARGERS e BC 119N DESKTOP CHARGER AD 106 CHARGER ADAPTER BC 145 ac ADAPTER For rapid charging of battery packs An AC adapter is supplied with the
9. F and Microwave The following accessories are authorized for use with this product Use of accessories other than those specified may result in RF ex posure levels exceeding the FCC requirements for wireless RF ex posure Belt Clip MB 94 Rechargeable Li lon Battery Pack BP 231 and Speaker microphone HM 131L To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupa tional use always adhere to the following guidelines CAUTION DO NOT operate the radio without a proper antenna attached as this may damaged the radio and may also cause you to exceed FCC RF exposure limits A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio DO NOT transmit for more than 50 of total radio use time 50 duty cycle Transmitting more than 5096 of the time can cause FCC RF exposure compliance requirements to be exceeded The radio is transmitting when the Transmit indicator lights red You can cause the radio to transmit by pressing the PTT switch ALWAYS keep the antenna at least 2 5 cm 1 inch away from the body when transmitting and only use the Icom belt clip which is listed on page 33 when attaching the radio to your belt etc to ensure FCC RF exposure compliance requirements are not exceeded To provide the recipients of your transmission the best sound quality hold the antenn
10. G 5 E Caution A DANGER Charge the specified Icom batteries only Only tested and approved for use with genuine Icom batteries Fire and or explosion may occur when a third party battery pack or counterfeit product is charged CAUTION NEVER insert battery pack transceiver with the bat tery pack attached with wet or soiled into the charger This may re sult in corrosion of the charger terminals or damage to the charger The charger is not waterproof and water can easily get into it NEVER incinerate used battery packs Internal battery gas may cause an explosion NEVER immerse the battery pack in water If the battery pack be comes wet be sure to wipe it dry immediately particularly the bat tery terminals BEFORE attaching it to the transceiver Otherwise the terminals will become corroded or cause connection failure etc NEVER short the terminals of the battery pack Also current may flow into nearby metal objects such as a necklace etc Therefore be careful when carrying with or placing near metal objects carry ing in handbags etc AVOID leaving the battery pack in a fully charged or completely discharged condition for long time It causes shorter battery life In case of leaving the battery pack unused for a long time it must be kept safely after discharge or use the battery until the battery indi cator appears then remove it from the transceiver If your battery pack seems to have no capacity even after being
11. O z ICOM INSTRUCTION MANUAL VHF TRANSCEIVER IC F14 S UHF TRANSCEIVER IC F24 S This device complies with Part 15 of the FCC rules Operation is subject to the condition that this device does not cause harmful interfer ence Icom Inc SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode This radio is designed for and clas sified as Occupational Use Only meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such haz WARNING ards This radio is NOT intended for use by the General Population in an uncontrolled environment This radio has been tested and complies with the FCC RF exposure lim its for Occupational Use Only In addition your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans FCC OET Bulletin 65 Edition 97 01 Supplement C Evaluating Com pliance with FCC Guidelines for Human Exposure to Radio Fre quency Electromagnetic Fields American National Standards Institute C95 1 1992 IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre quency Electromagnetic Fields 3 kHz to 300 GHz American National Standards Institute C95 3 1992 IEEE Recom mended Practice for the Measurement of Potentially Hazardous Elec tromagnetic Fields R
12. a at least 5 cm 2 inches from your mouth and slightly off to one side The information listed above provides the user with the information needed to make him or her aware of RF exposure and what to do to as sure that this radio operates with the FCC RF exposure limits of this radio Electromagnetic Interference Compatibility During transmissions your Icom radio generates RF energy that can pos sibly cause interference with other devices or systems To avoid such in terference turn off the radio in areas where signs are posted to do so DO NOT operate the transmitter in areas that are sensitive to electro magnetic radiation such as hospitals aircraft and blasting sites Occupational Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC F14 F14S VHF TRANSCEIVER and IC F24 F24S UHF TRANSCEIVER EXPLICIT DEFINITIONS WORD DEFINITION WARNING Personal injury fire hazard or electric shock may occur CAUTION Equipment damage may occur If disregarded inconvenience only No risk NOTE ne of personal injury fire or electric s
13. as shown at left Optional unit installation 3 Cut the pattern on the PCB at the TX mic circuit MIC and RX AF circuit DISC as shown below Install the scrambler unit as shown at left Optional unit installa tion Replace the unit cover and the battery pack then rotate VOL to turn the power ON Z NOTE When uninstalling the scrambler unit Be sure to re solder the discon y nected points at left otherwise no E TX modulation or AF output is ES available ANNIN mm 5 BATTERY CHARGING E Battery charging Prior to using the transceiver for the first time the battery pack must be fully charged for optimum life and operation ZZ CAUTION To avoid damage to the transceiver turn it OFF while Z charging Recommended temperature range for charging 10 C to 40 C 50 F to 104 F The Li lon battery functions within 20 C to 60 C 4 F to 140 F Use the specified chargers BC 119N BC 121N and BC 160 NEVER use another manufacturer s charger Use the optional AC adapter NEVER use another manufacturer s AC adapter Recommendation Charge the supplied battery pack for a maximum of up to 10 hours Li lon batteries are different from Ni Cd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life Therefore charging the battery in in tervals and not for extended periods is recommended BATTERY CHARGIN
14. d out in the normal fashion Selective calling Non selective calling 3 CONVENTIONAL OPERATION E Receiving and transmitting Z NOTE Transmitting without an antenna may damage the trans Z ceiver See p 2 for antenna attachment Receiving Rotate VOL to turn power ON 2 Toggle CHANNEL SWITCH IC F14S F24S rotate CHAN NEL SELECTOR IC F14 F24 or push one of MR CH 1 to MR CH 4 key to select a channel Z For IC F14S F24S The memory channels 3 and 4 are available when MR CH 3 A and MR CH 4 keys are assigned When receiving a call adjust the audio output level to a comfort able listening level Transmitting Wait for the channel to become clear to avoid interference D While pushing and holding PTT speak into the microphone at a normal voice level When a tone signalling system is used the call procedure de scribed on p 13 may be necessary Release PTT to return to receive ZZ MPORTANT To maximize the readability of your signal 1 Pause briefly after pushing PTT 2 Hold the microphone 5 to 10 cm 2 to 4 inches from your mouth then speak into the microphone at a normal voice level WMMAA CONVENTIONAL OPERATION 3 Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict trans mission under the following conditions The channel is in mute condition Channel is busy Un matched or matched CTCSS is received
15. e the channel switch to select the pre pro grammed channel 1 or 2 Rotate the channel selector to select the pre programmed memory channels VOLUME CONTROL VOL Rotate to turn the power ON OFF and adjust the audio level e IC F14 F24 Oo PANEL DESCRIPTION 2 LED INDICATOR p 8 Lights red while transmitting Lights green while receiving a signal or when the squelch is open Lights blinks orange when the matched 2 5 tone code is re ceived according to the pre programming O SPEAKER MICROPHONE CONNECTOR SP MIC Connects the optional speaker microphone p 31 SP MIC jack cover NOTE Attach the SP MIC jack cover when the optional speak er microphone is not used p 4 DEALER PROGRAMMABLE KEY Lower The desired function can be assigned by your dealer p 9 Q PTT SWITCH PTT Push and hold to transmit release to receive DEALER PROGRAMMABLE KEY Upper The desired function can be assigned by your dealer p 9 ANTENNA CONNECTOR Connects the supplied antenna 9 Programmable key reference Upper Lower j 2 PANEL DESCRIPTION B LED indicator The LED indicator indicates several informa tion as follows Ref R Red G Green O Orange TX Turns Red while transmitting a signal RX Turns Green while receiving a signal Call LED ON When receiving a matched 2 5 tone Call LED Blink When receiving a matched 2 5 tone Fast Slow sca
16. er to water will result in serious damage to the transceiver The use of non Icom battery packs chargers may impair transceiver performance and invalidate the warranty FCC caution Changes or modifications to this device not expressly approved by Icom Inc could void your authority to operate this transceiver under FCC regulations Icom Icom Inc and the com logo are registered trademarks of Icom Incorpo rated Japan in the United States the United Kingdom Germany France Spain Russia and or other countries TABLE OF CONTENTS SAFETY TRAINING INFORMATION se i FOREWORD 4er de eee gei bane Aiea es eaten iii EXPLICIT DEFINITIONS wie c2 ee pi rente E eet pee te te cr get iii OPERATING NOTE S e 5 ouais iii PRECAUTION 1237 nk nahh A a eaaa ors a Aet Tri os iv TABLE OF CONTENTS 55 1 dee exon ee a aa ee pd uen ds TACCESSORIES o en derer Lente drser ddeevie s W Supplied accessories sem retenent W Accessory attachments ess e 2 PANEL DESCRIPTION eee W Front top and side panels B UED ndiCator iei erret daly pete erre rere te W Programmable function keys 3 CONVENTIONAL OPERATION W Turning power ON ssesem HM W Channel selection sem ii Call procedure ta eet Ate ees W Receiving and transmitting W Scrambler function ssesseH W Setting the squelch level ssesem E Man Down E
17. he transceiver laying down in a horizontal position for a pre set time period The optional UT 113 MAN DOWN UNIT is required After the emergency call the transceiver performs transmission and reception alternately with the following conditions Transmits the microphone signals Receives the signal and emits audio When the emergency cancel code is received the function is can celled Z IMPORTANT Set an emergency channel individually to provide certain emergency call operation is recommended NE EN 4 OPTIONAL UNIT INSTALLATION 18 E Optional unit installation Install the optional unit as follows D Rotate VOL to turn the power OFF and remove the battery pack p 3 2 Remove the unit cover ZZ NOTE Use a flat head screw driver or a similar flat instru A ment and insert into the hollow of the chassis then lift and Y take away the unit cover The removed cover cannot be used G again MQ Replace the unit cover and the battery pack then rotate VOL to turn the power ON Y NOTE The optional UT 109 UT 110 SCRAMBLER UNITS requires Y some PC board modifications Please refer to the additional in Y stallation as at right NSS OPTIONAL UNIT INSTALLATION 4 B Scrambler unit installation The following PC board modification is required when installing the optional UT 109 or UT 110 D Rotate VOL to turn the power OFF and remove the battery pack p 3 Remove the unit cover
18. hock OPERATING NOTES When transmitting with a portable radio hold the radio in a vertical position with its microphone 5 to 10 centimeters 2 to 4 inches away from your mouth Keep the antenna at least 2 5 centimeters 1 inch from your head and body f you wear a portable two way radio on your body ensure that the antenna is at least 2 5 centimeters 1 inch from your body when transmitting PRECAUTION A WARNING NEVER hold the transceiver so that the antenna is very close to or touching exposed parts of the body especially the face or eyes while transmitting The transceiver will perform best if the microphone is 5 to 10 cm 2 to 4 inches away from the lips and the transceiver is vertical A WARNING NEVER operate the transceiver with a headset or other audio accessories at high volume levels CAUTION NEVER short the terminals of the battery pack NEVER connect the transceiver to a power source other than the BP 230 BP 231 or BP 232 Such a connection will ruin the trans ceiver DO NOT push the PTT when not actually desiring to transmit AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below 22 F 30 C or above 140 F 60 C DO NOT modify the transceiver for any reason MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver and that the antenna and battery pack are dry before attachment Exposing the inside of the transceiv
19. mergency Call 4 OPTIONAL UNIT INSTALLATION eere 18 19 W Optional unit installation 2 00 00 eeen 18 W Scrambler unit installation e cc eeeeeeeeeeee nsec eee eeeeaeeee ees 19 5 BATTERY CHARGING einer 20 25 W Battery charging sess HH 20 Ke uiMEM L 21 W Optional battery chargers seem 22 6 SWIVEL BELT CLIP reren aaan aoia aan aeara aaan 26 29 E MB 93 contents eeeeennnnenememeenne mener 26 W To attach W To detach 7 OPTIONS ACCESSORIES 1 HM E Supplied accessories The following accessories are supplied D Flexible antenna 0 00 cee eee ees Battery pack n nuanua 002 c eee es 3 Belt clip creer dee Sa eae PE es Unit cover double sided tape 8 Jack cover with screws 0 0 cece eee ee eae Use the unit cover as a spare Ask your dealer for details 1 N 1 ACCESSORIES ll Accessory attachments Flexible antenna Connect the supplied flexible an tenna to the antenna connector ZZ CAUTION NEVER HOLD by the antenna when carrying the transceiver Transmitting without an antenna may damage the transceiver SN LI i ACCESSORIES 1 Battery pack To attach the battery pack Slide the battery pack on the back of the transceiver in the direc tion of the arrow 69 then lock it with the battery release button Slide the batte
20. n Blinks while Fast Slow scan is activated Je de LL TX low BATT2 Low BATT2 was detected during TX mode R R ihk NENNEN HC CH err Non programmed channel is selected PANEL DESCRIPTION 2 E Programmable function keys The following functions can be assigned to Upper and Lower programmable function keys Consult your Icom dealer or system operator for details concerning your transceivers programming If the programmable function names are bracketed in the following explanations the specific key used to activate the function depends on programming SCAN A KEY This key s operation depends on the Power ON Scan setting When the power ON scan function is turned OFF Push to start and cancel scanning operation In case of trans mission during scan cancels scanning When the power ON scan function is turned ON Push to pause scanning Scanning resumes after passing a specified time period In case of transmission during scan pauses scanning Scanning resumes after passing a specified time period SCAN B KEY Push to start and cancel scanning operation In case of transmis sion during scan pauses scanning Scanning resumes after pass ing a specified time period PRIORITY CHANNEL KEYS Push to select the Priority A or Priority B channel Push and hold Prio A Rewrite to rewrite the Prio A channel MR CH 1 2 3 4 KEYS Push to select a memory channels 1 to 4 directly G NOTE The memory channels 3
21. ry pack until the battery release button makes a click sound To release the battery pack Push the battery release button in the direction of the arrow 8 as shown below The battery pack is then released Z NEVER release or attach the battery pack when the transceiver Zs wet or soiled This may result in water or dust getting into the Z transceiver battery pack and may result in the transceiver being damaged A 1 ACCESSORIES Jack cover Attach the jack cover when the optional speaker microphone is not used To attach the jack cover To detach the jack cover Attach the jack cover to the Unscrew the screws with a SP MIC connector phillips screwdriver Tighten the screws Detach the jack cover for the speaker microphone connec tion ACCESSORIES 1 9 Belt clip To attach the belt clip D Release the battery pack if it is attached Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a click sound To detach the belt clip D Release the battery pack if it is attached 2 Pinch the clip 9 and slide the belt clip in the direction of the arrow 3 mm 2 PANEL DESCRIPTION E Front top and side panels iC F14S F24S IC F14 F24 Ga fe A Bn eo N e 9 c Nna Microphone CHANNEL SW SELECTOR e IC F14S F24S Toggl
22. to wide The wide passband width can be selected from 25 0 or 20 0 kHz using the CS F14 CLONING SOFTWARE PMR operation only Ask your dealer for details Push and hold to select the IF bandwidth to narrow PANEL DESCRIPTION 2 DTMF AUTODIAL KEY Push to transmit the programmed DTMF code CALL KEYS Push to transmit a 2 5 tone code e Call transmission is necessary before you call another station de pending on your signalling system Call A and or Call B keys may be available when your system em ploys selective Individual Group calls Ask your dealer which call is assigned to each key EMERGENCY KEYS Push and hold to transmit an emergency call When Emergency Single Silent or Emergency Repeat Silent is pushed an emergency call is transmitted without a beep emission If you want to cancel the emergency call push or push and hold the key again before transmitting the call The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre setting VOICE SCRAMBLER FUNCTION KEYS Push to turn the voice scrambler function OFF Push and hold to turn the voice scrambler function ON OPT OUT KEYS Push to inactivate the connected output signal level Push and hold to activate the connected output signal level SIREN KEY Push to emit a siren This function can be used for situations other than an emergency alert such as a security alarm for example
Download Pdf Manuals
Related Search