IBM T 541 User's Manual
Contents
1. Click the MONITOR tab 8 Click the PROPERTIES button 9 Click the DRIVER tab 4 0 Open the UPGRADE DEVICE DRIVER WIZARD window by clicking on UPDATE DRIVER and then Click the NExT button 11 Select the Display a list of the known drivers for this device so that can choose a specific driver and then Click the NExT button 12 Insert the Setup CD into the CD drive and click the HAVE Disk button 13 Click OK 14 Ensure that the CD drive letter is selected and then select the Drivers folder 15 Choose IBM T541 monitor and Click OK The files will be copied from the CD to your hard disk drive 16 Close all open windows and remove the CD 17 Restart the system The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles Driver Installation for Windows XP This section must be completed before continuing with the Windows XP Auto Setup on page 10 On LCD monitors unlike CRTs a faster refresh rate does not improve display quality IBM recommends using either 1024 x 768 ata refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To use the Plug and Play feature in Microsoft Windows XP files should be loaded from the IBM Monitor CD 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow the system to boot into Windows XP 4 Open the DISPLAY PROPERTIES2. an IBM product program or service is not intended to state or imply that only IBM s product program or service may be used Any functionally equivalent product program or service that does not infringe any of IBM s intellectual property rights or other legally protectable rights may be used instead of the IBM product program or service Evaluation and verification of operation in conjunction with other products programs or services except those expressly designated by IBM are the user s responsibility IBM may have patents or pending patent applications covering subject matter in this document The furnishing of this document does not give you any license to these patents Trademarks The following terms used in this publication are trademarks or service marks of the IBM Corporation in the United States other countries or both HelpCenter IBM ENERGY Star is a U S Govt registered trademark Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the United States other countries or both Other company product and service names may be trademarks or service marks of others T541 Flat Panel Monitor User Guide Contents Settingiup the MIORILOP ANANA 2 System Hardware gia agua SA 2 Handling atala alar 2 Ro Wo NANA 3 Monitor InstallatlOn 2 2 0 nina da 1a vacca tu aera 4 Connecting MUSI deno SN TC 4 Switching on your peo dem 5 Monitor Driver INStallaton AAA 6 Driver installation for W
3. image is already L optimized for many display modes however the user controls can be used to adjust the image to your liking e The settings are saved L after adjustment and when exiting the OSD and will be effective thereafter USER CONTROL FEATURES Icon Monitor controls O Switches the monitors on and off lt Display main OSD menu and selects highlighted menu item and Moved the cursor to highlight icons or make adjustments Exits from current OSD menu Icon Direct Access Functions i Bring up Brightness adjustment EZE Bring up auto image setup al CONTROLS LOCK UNLOCK This feature allows you to secure the current control settings while allowing the user to adjust Brightness or Contrast so that they cannot be inadvertently changed Push and hold the enter button for 10 seconds the message Controls Locked appears You can unlock the OSD controls at any time by pushing the enter button _ 1 for 10 seconds the message Controls Unlocked will appear Ge 1es2 Switch between input signals 15 ENGLISH On screen display OSD controls The LCD monitor needs l time to become thermally stable the first time you turn it on each day Thus to achieve more accurate adjustments for parameters allow the LCD monitor to warm up be On for at least 15 minutes before making any screen adjustment Initial appearance of OSD main m
4. this device so that can choose a specific driver and then select the NExT button 7 Insert the Setup CD into the CD driver and click the HAVE DISK button 8 Click OK 9 Ensure that the CD drive letter is selected and then select the Drivers folder 10 Choose IBM T5441 monitor and Click OK The files will be copied from the CD to your hard disk drive 11 Close all open windows and remove the CD 12 Restart the system The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles ENGLISH Driver Installation for Windows 2000 or Windows Me This section must be completed before continuing with the Windows2000 Windows Me Auto Setup on page 10 OnLCD monitors unlike CRTs a faster refresh rate does not improve display quality IBM recommends using either 1024 x 768 ata refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To use the Plug and Play feature in Microsoft Windows 2000 or Microsoft Windows Millennium Edition Me files should be loaded from the IBM Monitor CD 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow the system to boot into Windows 2000 or Windows Me 4 Open the DISPLAY PROPERTIES window by clicking START SETTINGS CONTROL PANEL and then double clicking the DISPLAY icon 5 Click the SETTINGS tab 6 Click the ADVANCED button 7
5. your wrists when not typing Consider using a wristpad Eyesight Working with monitors in common with any prolonged close work can be visually demanding Look away from the screen periodically and have your eyesight checked regularly Screen settings Set the screen brightness and contrast to a comfortable level You may have to adjust these settings as the lighting changes during the day Many application programs let you select color combinations which can help you to view in comfort See the User controls section on page 15 for more information 13 Adjusting the Monitor Position gt With the IBM Flat Panel L Monitor you can adjust its position in various ways for maximum comfort Viewing Angle You can tilt the screen forward and backward as shown below figure A Swivel You can swivel the screen leftward and rightward as shown below figure A Height You can adjust height of the screen figure B Figure A Figure B Caring for your Monitor Be sure to turn off the power before you perform any maintenance on the monitor Clean your monitor as follows Gently wipe the covers and the screen with a soft cloth Remove finger marks and grease with a damp cloth and mild detergent Never use flammable cleaning materials to clean your IBM monitor or any other electrical apparatus 14 Adjusting Your LCD Monitor User controls The
6. 480 72 8 77 3 Hz 36 38 38 63 kHz 640 x 350 67 9 72 1 Hz 30 56 32 45 kHz 720 x 400 67 9 72 1 Hz 30 56 32 45 kHz 800 x 600 54 3 57 7 Hz 34 14 36 26 kHz 800 x 600 58 2 61 8 Hz 36 76 39 04 kHz 800 x 600 69 8 74 2 Hz 46 66 49 54 kHz 800 x 600 72 8 77 3 Hz 45 49 48 31 kHz 832 x 624 72 8 77 3 Hz 48 21 51 19 kHz 1024 x 768 58 2 61 8 Hz 46 95 49 85 kHz 1024 x 768 67 9 72 1 Hz 54 81 58 20 kHz 1024 x 768 72 8 77 3 Hz 58 20 61 80 kHz
7. 512 Hxx uses a 15 inch TFT LCD Height 13 37 inch 339 5 mm Min 18 29 inch 464 5 mm Max Width 14 38 inch 365 2 mm Depth 10 19 inch 259 0 mm Weight With Stand 5 3 kg 11 68 Ibs Image Viewable Image Size 15 inch 381 0 mm Maximum Height 304 1 mm Maximum Width 228 1 mm Pixel Pitch 0 297 mm H x 0 297 mm V Power Input Supply Voltage 100 240 Vac 60 50 3Hz Rated Current 0 6A Power Normal Operation lt 35W Consumption Active off lt OM Off lt 1W Video Input Input Signal Analog 75 ohm 0 7V Digital DVI 1 0 Horiz Addressability 1024 pixels max Vert Addressability 768 lines max Clock Frequency 80 MHz Digital 80 MHz Analog Sync Input Type Analog Separate Composite SOG Digital DVI 1 0 Communications VESA DDC E DDC Supported Display Standard modes IBM VESA MAC Modes Horiz Vert Freq See Factory Set Display Modes on page 19 See Display Mode Ranges on page 24 Environment Temperature Operating Storage Shipping Humidity Operating Storage Shipping 10 to 35 C 20 to 60 C 20 to 60 C 10 to 80 5 to 95 5 to 95 23 ENGLISH 24 Display Mode Ranges Addressabillty Refresh Rate Range 3 Horizontal Frequency Range 3 640 x 480 58 2 61 8 Hz 30 56 32 45 kHz 640 x 480 64 0 68 0 Hz 33 95 36 05 kHz 640 x
8. BY ON it may automatically turn off while you are waiting for it to warm up The size and diversity of the L dot pattern varies with the screen resolution e Position the mouse pointer at L the bottom center of the screen This allows AUTO SETUP to run properly 10 1 Turn on the monitor first then the computer If the message CHECK VIDEO CABLE is displayed or if nothing is displayed check e that the video interface cable is not connected properly e the correct video adapter card is not installed Wait approximately 15 minutes until the monitor warms up Ensure that the icon bar and tool bar if displayed are at the bottom of the screen Insert the CD labelled BM Monitor CD into the CD drive Check the operating system installed on your computer and follow the instructions from the table below Operating System Step1 Step2 Step3 Open Windows 3 1 PROG RAM Select Manager RUN Windows 95 Type E TESTPAT Windows 98 Be and press elect Gide 2000 START Select RUN ENTER Windows Me Windows XP Microsoft Windows NTG84 0 6 When the test pattern appears press the Image Setup direct access button atthe bottom of the monitor to run the image setup 7 To clear the Image Setup test pattern press the ESC key on your keybord You have completed the monitor setup for Windows If you use other operating systems perform the appropriate AUTO SETUP for those syste
9. ODES Display all user modes stored in the monitor The current display mode will be shown at the base of all information screens USER MODES Use the and gt buttons to move between information screens ENGLISH Further Information Display modes If your computer has L previously been used with a CHT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display you may need to re attach the CRT monitor temporarily until you have reconfigured the computer preferably to 1024 x 768 at 60Hz The display mode the monitor uses is controlled by the computer Therefore you should refer to your computer documentation for details on how to change display modes The image size position and shape may change when the display mode changes This is normal and the image can be readjusted using AUTO SETUP and the monitor controls Unlike CRT monitors which require a high refresh rate to minimize flicker TFT technology is inherently flicker free If possible configure your computer for 1024 x 768 addressability at 60Hz vertical refresh rate For the display modes listed below the screen image has been optimized during manufacture Factory Set Display Modes Addressabillty Refresh Rate Bez 640 x 480 60 Hz 31 5 kHz 640 x 480 66 Hz 35 0 kHz 640 x 480 75 Hz 37 5 kHz 640 x 350 70 Hz 31 5 kHz 720 x 400 70 Hz 31 5
10. T541 Flat Panel Monitor User Guide ENGLISH First Edition September 2002 Note For important information refer to the Monitor Safety and Warranty manual that comes with this monitor This publication could contain technical inaccuracies or typographical errors Changes are made periodically to the information herein these changes will be made in later editions IBM may make improvements and or changes in the product s and or program s at any time It is possible that this publication may contain reference to or information about IBM products machines and programs programming or services that are not announced in your country Requests for copies of this publication and for technical information about IBM products should be made to your IBM Authorized Dealer or IBM Retailer No part of this publication may be reproduced or distributed in any form or by any means without prior permission in writing from the International Business Machines Corporation Copyright International Business Machines Corporation 2002 All rights reserved Note to U S Government Users Documentation related to restricted rights Use duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp Notices References in this publication to IBM products programs or services do not imply that IBM intends to make these available in all countries in which IBM operates Any reference to
11. ems See Auto Setup for the computer on page 9 for details 22 Possible Problem Cause Suggested Action Reference Screen is blank Display mode of Reconfigure key on the Further and power the computer is computer to use a supported Information indicator is outside the display mode flashing green range of the section on every 0 5 monitor page 19 second CHECK VIDEO The monitor is e Check that the signal cabel C CABLE not receving a is firmly connected to the SAIA message is video signal computer y monitor shown and e Check that no pins are bent Section on power indicator in the signal cable connector page 4 is steady amber ar Ai There are noises e Select IMAGE SET UP menu User in the video in the OSD Then select Controls signal MANUAL to adjust FINE section on COARSE settings page 15 Ima i User ge appears The color setting e Adjust the Color settings to be discolored may be incorrect Controls section on page 15 A few dots are missing discolored or inappropriately lighted The LCD contains over 2 300 000 thin film transistors TFTs A small number of missing discolored or lighted dots may be present on the screen which is an intrinsic characteristic of the TFT LCD technology and is not an LCD defect Specifications Power consumption figures are for the monitor and the power supply combined This color monitor Type model 9
12. enu Analog Signal input MAIN MENU DSUB ANALOG INPUT sub menu i9 BRIGHTNESS The settings adjustable with the user controls are viewed through the On Screen Display OSD Press the enter button 2 to display the main OSD menu Digital Signal input MAIN MENU DV I DIGITAL INPUT OSD functions OSD Icon Description sub menu s Greta OO Adjusts brightness E BRIGHTNESS gt Adjusts contrast CONTRAST gt LK IMAGE SET UP The IMAGE SET UP function is used to adjust the level of noise in the video signal which causes horizontal lines or areas on the screen where the image appears to be unstable and jitters or shimmers This can be done automatically or manually e It is not applicable to digital input AUTO If AUTO is selected the image will automatically adjust 16 Controls and OSD Icon Description Sub menu s Adjustments If manual is selected the user will go MANUAL To adjust the focus of the LK to the manual adjustment screen display This item allows Fine you to remove any IMAGE SET UP e Coarse horizontal noise and clear CONT or sharpen the image of characters Fine adjustments should be done after adjusting the Coarse Select the COLOR MODE you find COLOR MODE P t1 most comfortable or fine tune the rese colors using the USER COLOR MODE Pink Whi
13. ess for as many of the color and video modes as you need 9 When the test pattern appears press the Image Setup direct access button at the bottom of the monitor to run the image setup 10 To clear the Image Setup test pattern press the ESC key on your keybord 11 Type Exit at the command prompt to return to Windows Noo db E D If you use other operating systems perform the appropriate Image Setup for those systems and also see Image Setup Windows 3 1 Windows 95 Windows 98 Windows 2000 Windows Me Window XP or Windows NT workstation on page 10 11 Manually adjusting the image settings If the monitor is in standby l mode STANDBY ON it might automatically turn off while you are waiting for it to warm up 12 Normally you can complete the setup procedure using Image Setup however if your screen image is still distorted after you perform Image Setup or the setup CD does not run on your system perform MANUAL SETUP 1 Have your monitor turned on for about 15 minutes until the monitor warms up Display the image you most frequently use on the screen Press the OSD Enter button at the botton of the monitor to display the initial OSD menu Use an Arrow button le or to select the IMAGE SET UP icon X and press the OSD Enter button to access the function Using an Arrow button or select MANUAL press lt and then press once to select COARSE Left and right arrow adjustmen
14. indows 95 or Windows 98 6 Driver installation for Windows 2000 or Windows MO rra 7 Driver installation for Windows XP arreoa 8 Image Setup for Analog Input AAA 9 d es SQUID BN RR RE 9 AutoSetup for Windows 3 1 Windows 95 Windows 98 Windows 2000 Windows Me Windows XP or Windows NT sua 10 Adjusting the image settings in DOE 11 Manually adjusting the image settings na 12 Ergonomic gia LD a ga 13 Workplace PFE PALE OM AAE 13 Working Practices MESE 13 Adjusting the Monitor SELATAN 14 Caring for your Aue E 14 Adjusting Your LCD Monitor uersa haer rk uu RR nun Rx Or nel gu Eu a prr n arre 15 a deleite AAE 15 On screen display OSD galaia EEAO 16 Further Information AAE 19 Display MOES AAA 19 Power iat alera SA 20 UI daiala PAN 21 elene die aA 23 ENGLISH Setting up the monitor System Hardware Requirements This monitor requires a computer with a suitable on board sub system or Video Adapter card that can support XGA 1024 x 768 SVGA 800 x 600 or VGA 640 x 480 at 60Hz Handling Instructions 1 Do not support the monitor within the screen area The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure 2 Before using your monitor for the first time remove the clear protective film from the front of the screen ENGLISH Desk Top Use Remove the clip on stand models Before adjusting your monitor for the first time remove the lock
15. ing clip on rear of the stand Carefully hold the screen of the monitor and then sqeeze at arrows shown to remove figure A Monitor Installation Connecting your Monitor 1 Turn off your computer and all attached devices Next unplug the power cord s to your computer and all attached devices 2 Connect the signal cable The analog signal cable is already connected to your monitor g The analog connector is the blue connector When connecting the analog signal cable Figure A Connect the free end of the attached signal cable to the 15 pin Monitor port on the computer and tighten screws Figure A a If connecting a DVI D digital signal cable Figure B Connect one end of the monitor signal cable to the white connector on the rear panel of the monitor Connect the other end to the white connector on the rear panel of the computer and tighten the screws Cable not supplied Optional 4 Figure B ENGLISH 3 Connect the power cord to the monitor and then plug the power cord into a properly grounded outlet Next reconnect the power cord s to your computer and all attached devices Switching on your Monitor 1 Switch on your monitor by pushing and releasing the power switch marked O at the front of the bezel To switch off your monitor push and release the power switch again Switch on your computer 3 If you are using the analog connector run AUTO SETUP by fo
16. kHz 800 x 600 56 Hz 35 2 kHz 800 x 600 60 Hz 37 9 kHz 800 x 600 72 Hz 48 1 kHz 800 x 600 75 Hz 46 9 kHz 832 x 624 75 Hz 49 7 kHz 1024 x 768 1 60 Hz 48 4 kHz 1024 x 768 70 Hz 56 5 kHz 1024 x 768 75 Hz 60 0 kHz T Recommended Note VESA timings are as detailed in the VESA Display Monitor Timing Specification Version 1 0 Revision 0 8 Dated 09 17 98 19 Power Management 20 To benefit from power management the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association VESA Display Power Management Signaling DPMS Standard The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user definable period There are several states as described in the table below As an ENERGY STAR 2000 Partner IBM has determined that this product meets the ENERGY STAR 2000 guidelines for energy efficiency IBM recommends that you switch off your monitor at the end of each working day or whenever you expect to leave it unused for long periods during the day Power Restoring 3 mplian State Indicator Screen Operation Compliance On Steady green Normal Press a key or ENERGY Active off Steady amber Blank move the mouse t STAR 2000 t There may be a slight delay before the picture reappears Troubleshooting If you have a problem setting up or using your monito
17. llowing the instructions in the Auto Setup section on page 9 Monitor Driver Installation Driver installation for Windows 95 or Windows 98 This section must be completed before continuing with the Windows95 or Windows98 Auto Setup on page 10 On LCD monitors unlike L CRTs a faster refresh rate does not improve display quality IBM recommends using either 1024 x 768 ata refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz To use the Plug and Play feature in Microsoft Windows 95 or Windows 98 files should be loaded from the JBM Monitor CD 1 Turn off the computer and all attached devices 2 Ensure that the monitor is connected correctly 3 Turn on the monitor and then the system unit Allow the system to boot into Windows95 or Windows98 Your computer s Plug and Play code may warn you that your system hardware has changed This means that it has detected your new monitor for the first time 4 Open the DISPLAY PROPERTIES window by clicking START SETTINGS CONTROL PANEL and then double clicking on the pisPLAY icon 5 Click the SETTINGS tab In case of Windows 95 6 1 Click the CHANGE DISPLAY TYPE button 2 Click the CHANGE MONITOR TYPE button In case of Windows 98 6 1 Click the ADVANCED button 2 Click the MONITOR tab 3 Open the UPGRADE DEVICE DRIVER WIZARD window by clicking on CHANGE button and then select the NET button 4 Click the Display a list of the known drivers for
18. ms and also see Adjusting the image settings in DOS on page 11 ENGLISH Adjusting the image settings in DOS f the monitor is in standby L mode STANDBY ON it may automatically turn off while you are waiting for it to warm up If this happens switch off the monitor and switch it on again after a few seconds f you are using PC DOS V L change to U S mode by typing CHEV US and pressing ENTER at the command prompt You must use when you run DOS Auto Setup The size and diversity of the L dot pattern varies with the screen resolution Ifthe screen flickers L repeat the setup several times until the flicker is minimised or adjust it manually by following refer to Manual Setup on page 12 1 Turn on the monitor first then the computer If the message CHECK VIDEO CABLE is displayed or if nothing is displayed check e that the video interface cable is not connected properly e the correct video adapter card is not installed Wait approximately 15 minutes until the monitor warms up Insert the CD labelled IBM Monitor CD into the CD drive Display the command prompt screen of the DOS full screen display At the command prompt type the CD drive letter and press ENTER Type TESTPATD and press ENTER Select from the screen the number for the color or text mode you want to setup 8 Select from the screen the number for the video mode you want to setup You may repeat this proc
19. nual Setup on page 12 e The AUTO SETUP process only applies to the current screen mode When a new mode is selected repeat this section to reset the monitor For digital input image setup is not required When you first use your monitor you must perform Auto Setup for analog input If you are using digital input continue with the instructions on page 13 This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing After you perform Auto Setup the settings are stored and used each time you turn on the monitor In order to optimize the displayed image a set up utility is provided on the IBM Monitor CD Operation of this utility is dependent on the operating System on your computer You may choose to run AUTO SETUP for each operating system that you use This means that if you sometimes use your monitor while running any version of Windows and sometimes also use it from within DOS not a DOS window you must run AUTO SETUP for both Windows and DOS You may run versions of AUTO SETUP in any order Before you begin AUTO SETUP for your computer make sure the computer video mode is set in the range of the supported screen resolution shown in the table on page 19 You should perform AUTO SETUP for each screen mode you use AutoSetup for Windows 3 1 Windows 95 Windows 98 Windows 2000 Windows Me Windows XP or Windows NT D the monitor is in standby mode STAND
20. r you may be able to solve it yourself Before calling your retailer or IBM try the suggested actions that are appropriate to your problem software on your computer Press the gt to switch between analog and digital mode If the panel is the wrong mode for the signal being provided the monitor appears to go into sleep mode Problem Possible Suggested Action Reference Cause Screen is No power to Ensure that the electrical outlet Connecting blank and monitor and the monitor are both your power switched on Monitor indicator is off Check that the power cord section on is firmly plugged into the page 4 electrical outlet and the power supply unit If the power cord plug has a removalble fuse replace it Try another power cord Try another electrical outlet Check the power connection at the back of the panel Screen is blank Brightness Adjust brightness and contrast User and power and Contrast controls indicator is may be too section on steady green low page 15 Screen is blank The monitor is Press any key on the keyboard Power and power in the Power or move the mouse to restore Management indicator is Management operation section on steady amber Standby state Check the Power Management page 20 21 ENGLISH e For image problems you L may want to run AUTO SETUP again before consulting to this section In most cases AUTO SETUP can fix the probl
21. t indicators become illuminated see page 17 Use the Arrow buttons to manually adjust to correct as much as possible for jitter or noise in the image then press 3 to save the changes Use an Arrow button to select FINE and press the button Use the Arrow buttons again to tune the image to your liking When finished press the Exit button gt four times to exit from the OSD You have completed the monitor setup ENGLISH Ergonomic Considerations Workplace Preparation e This section gives advice on what you should consider before you set up your monitor Height Position the monitor so that the top of the screen is slightly below your eye level when you sit at your workstation Orientation Choose a position that gives the least reflection from lights and windows usually at a right angle to any windows Positon the monitor directly in front of you so that you do not have to twist your body to use it Tilt the monitor to a comfortable viewing angle Working Practices This section gives advice l on how you can work comfortably and reduce fatigue Rest Take regular breaks Vary your posture stand up and stretch occasionally as prolonged use of computer workstations can be tiring Back Sit back in your chair and use the backrest Hands Use a light touch on the keyboard keeping your hands and fingers relaxed Allow a space in front of the keyboard to rest
22. te menu if necessary COLOR Preset 2 Normal White Preset 3 Blue White USER COLOR MODE e Red Increases or decreases redness e Green Increases or decreases greenness e Blue Increases or decreases blueness Changes the position of the OSD on the H POSITION col screen EI O OSD Position gt V POSITION gt ol 17 ENGLISH 18 Controls and D Icon Description Sub menu S pepe E S Adjustments Reset should return all available functions e YES gt 06 apart from language which should not change unless adjusted via the eNO RESET LANGUAGE menu fo their factory presets c3 Moves the screen left and right e Is not availible with a digital input E azi H POSITION lt t E Moves the screen up and down e Is not availible with a digital input rea Az V POSITION ea gt Sg Changes the size of the OSD menu on the screen SMALL E MEDIUM OSD SIZE BIG The language chosen affects only the language of the OSD ENGLISH E Select one of the five language to use for the OSD bi IDEE It has no effect on any software running on the computer Language y 3 P e ITALIANO ESPANOL x To select OSD display duration time 5 60 seconds OSD TIME Display model name serial number year of manufacture INFORMATION and microcode level Information Display all preset modes stored in the monitor PRESET M
23. window by clicking START SETTINGS CONTROL PANEL and then double clicking the pisPLAY icon Click the sETTINGS tab Click the ADVANCED button Click the MONITOR tab Click the PROPERTIES button Click the DRIVER tab 0 Open the Hardware Update Wizard window by clicking on UPDATE DRIVER and then Click the NExT button 11 Select the Install from a list or Specific location Advanced and then Click the NExT button 12 Insert the Setup CD into the CD drive and click the HAVE Disk button 13 Click OK 14 Ensure that the CD drive letter is selected and then select the Drivers folder 15 Choose IBM T541 monitor and Click OK The files will be copied from the CD to your hard disk drive 16 Close all open windows and remove the CD 17 Restart the system The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles zk GO ON Oo O ENGLISH Image Setup for analog input Auto Setup Before carrying out this section it is very important that the correct monitor drivers have been installed See pages 6 and 8 The Setup Utility included L on the setup CD displays a test pattern of dots It does not replace or modify the display drivers The Auto Setup instructions l require the monitor to be warmed up for 15 minutes This is not required for normal operation If your computer does not L run With the setup CD shipped with the monitor refer to Ma
Download Pdf Manuals
Related Search