IBM 07N2230 User's Manual
Contents
1. Table 2 Product specifications Width 106 4 mm Outer dimensions converter box housing Height 30 8 mm Depth 107 6 mm Weight converter box housing Input voltage supplied from monitor Power consumption maximum Video input AN NZS 3548 CISPR22 A FCC A Standards compliance IEC 60950 3rd Ed UL 60950 3rd Ed CSA C22 2 No 60950 00 VCCI A ISO 13406 2 Temperature Operating 0 35 deg C Shipping by air amp within 24 hours 20 60 deg C Storage Shipping other than above 1 60 deg C Humidity Operating 8 80 No Condensation Shipping by air amp within 24 hours 8 80 No Condensation Storage Shipping other than above 8 80 No Condensation 15 P N 55P5776 Appendix B Regulatory Compliance Federal Communications Commission FCC Statement IBM Converter box P N 07N2230 FRU P N 13M3200 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be2. Genehmigung des Bundesminesters f r Post und Telekommunikation oder des Bundesamtes f r Post und Telekommunikation betrieben werden Die Genehmigung wird erteilt wenn keine elektromagnetischen St rungen zu erwarten sind 16 P N 55P5776 Auszug aus dem EMVG vom 9 Nov 92 Para 3 Abs 4 Hinweis Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht ver ffentlicht worden European Union EMC Directive This product is in conformity with the protection requirements of the EU Council Directive 89 366 ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non recommended modification of the product including the fitting of non IBM option cards This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22 European Standard EN 55022 The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Union Europ enne Directive Conformit lectromagn tique Ce produit est conforme aux exigences de pr
3. P N 55P5776 displayed connector of the graphics card Action 1 Connect the converter box to the connector supporting DVI Dual Link output referring to the instructions in Chapter 2 Cause 2 The monitor s EDID setting is incorrect Action 2 Set the correct value for your graphics card referring to the T221 Flat Panel Monitor Users Guide Restart the system after making any changes Cause 3 You are using an unsupported graphics card or the device driver is downlevel Action 3 Check that the graphics card is a supported type and that the latest level device drivers are being used see the T221 Flat Panel Monitor Users Guide for further information amp details on how to access the web support page Cause 4 The graphics card setting is incorrect Action 4 Some graphics cards may require the video output setting changed by using a software program associated with the graphics card For the detail refer to the user s manual for the graphics card The Color Management Utility Cause 1 The USB cable is connected to the connector B of the or the Firmware Update monitor Utility does not work Action 1 Disconnect the USB cable and then connect the USB cable to the converter box that is connected to the connector A of the monitor 14 LAU P N 55P5776 Appendix A Product Specifications The following table shows the converter box specifications They only apply when the converter box is used with the IBM T221 monitor
4. 11 3 Changing the Monitor EDID Setting ss 11 4 Troubleshooting uie everti ose diia 12 Appendix A Product Specifications ses 15 Appendix B Regulatory Compliance ss 16 Figures Pigs Ds COn verter boxe iio eS 6 Fig 2 USB cable length 200cm approx nennen 6 Fig 3 Converter signal cable length 65cm approx 7 Fig 4 User s guide this Doo 7 Fig 5 Dual Link signal cable length 200cm approx eee 7 Fig 6 Dual EM A A Adi 8 Fig 7 Connection of the converter signal cable and the monitor 9 Fig 8 Connection of the converter signal cable and the converter box 9 Fig 9 Connection of the Dual Link signal cable and the converter box 10 Fig 11 Connection of the Dual Link signal cable and a graphics card 10 Tables Table Problems and ACEIORS preneur sterne ent oor NS 12 Table 2 Product specifications 2 4 2 ce cien ce cette te tien enes ie spa aaa 15 P N 55P5776 1 Preparation for Installation This chapter describes how to make sure that you have the required system configuration and components for using the converter box 1 1 Required System Configuration To use the converter box with an IBM T221 Flat Panel Monitor you must have a computer fitted with a DVI compliant graphics card that supports the DVI Dual Link interface See the T221 Flat Panel Monitor Users Guide If your computer does not have a graphics card install one before you use the converter box for the installation proce
5. computer or graphics card may be damaged when you power on the computer Insert the connector straight and firmly so as not to bend the connector pins 2 3 Setup Replace the covers on the back of the monitor and return the monitor to the upright position Plug the power cords of the monitor and computer into wall outlets The power lamp on the converter box should come on steady green indicating normal operation The power lamp on the converter box does not come on unless the monitor is connected to an AC power supply 3 Changing the Monitor EDID Setting Change the monitor s Extended Display Identification Data EDID setting to suit your particular graphics card See the T221 Flat Panel Monitor Users Guide for further information This completes converter box installation and setup 11 P N 55P5776 4 Troubleshooting This chapter explains what to do if a problem occurs while you are using the monitor Only problems related to the converter box are covered here Refer also to your monitor manual for troubleshooting information Table 1 Problems and Actions Blank screen LED lamp on the Cause 1 No power to the converter box monitor is steady amber or Action 1 Power on the monitor and make sure that the monitor blinking amber power lamp is steady amber or blinking amber Then look at the power lamp on the converter box next to the connector for the converter signal cable 07N2229 If the lamp did n
6. required to correct the interference at his her own expense Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Industry Canada Class A Emission Compliance Statement This Class A digital apparatus complies with Canadian ICES 003 Avis de Conformit la R glementation d Industrie Canada Cet appareil num rique de classe A est conforme la norme NMB 003 du Canada Deutsche EMV Direktive electromagnetische Vertr glichkeit Dieses Gerat ist berechtigt in bereinstimmung mit dem deutschen EMVG vom 9 Nov 92 das EG Konformitatszelchen zu f hren Der Aussteller der Konformit tserkl rung ist die IBM UK Greenock Dieses Gerat erf llt die Bedingungen der EN 55022 Klasse A F r diese Klasse von Ger ten gilt folgende Bestimmung nach dem EMVG Ger te d rfen an Orten f r die sie nicht ausreichend entst rt sind nur mit besonderer
7. LAU P N 55P5776 Converter Box for the T221 Flat Panel Monitor User s Guide P N 55P5776 Preface You will need a converter box if you are using an IBM 1221 Flat Panel Monitor connected to a computer fitted with a graphics card that supports the DVI Dual Link interface If your graphics card is not a dual link type do not use a converter box This manual describes the preparation required before using the converter box how to connect the converter box to the monitor how to adjust the monitor and what to do if a problem occurs Trademarks DVI is a trademark of the Digital Display Working Group DDWG EDID is a trademark of the Video Electronics Standard Association VESA ATI FireGL and RADEON are trademarks or registered trademarks of ATI Tec hnologies Inc TMDS is a trademark of Silicon Image Incorporated nVIDIA Quadro FX 1000 FX 2000 and FX 3000 are trademarks or registered trademarks of nVIDIA Corporation P N 55P5776 Precautions for using the converter box safely and correctly gt DANGER To avoid electrical shock Never remove the cover of the converter box Never connect or disconnect the converter box during an electrical storm Any equipment to which the converter box is attached must also be connected to properly wired and grounded electrical outlets e The monitor to which the converter box is connected must be unplugged at the wall to disconnect it from the power suppl
8. dure see your graphics card manual You can still get a picture on the monitor during card installation without using a converter box Important If you use a DVI video graphics card not supported by IBM you will be liable for any damage or defects that may result IBM offers no comments advice or guarantees regarding the functionality quality or performance of unsupported graphics cards The monitor firmware FPGA LOGIC must be version 44 48 50 52 or higher to use a converter box See the T221 Flat Panel Monitor Users Guide for more information 1 2 Checking Parts The converter box should be handled with care Check that you have the following components P N 55P5728 Fig 1 Converter box Fig 2 USB cable length 200cm approx P N 55P5776 Fig 3 Converter signal cable length 65cm approx Fig 4 User s guide this book Fig 5 Dual Link signal cable length 200cm approx Important Do not use other cables for T221 and the converter box Do not use these cables for other equipment than the T221 monitor and converter box 2 Connecting the Converter Box See your monitor manual for instructions and precautions on handling the monitor Important Use a large desk or table covered with a soft thick cloth if you need to lay the monitor face down during installation Make sure there are no pencils clips or other hard objects under the monitor screen and avoid knocking or bumping
9. ot come on the converter box has no power supply Re connect the cable between converter box and monitor referring to the instructions in Chapter 2 for installing the converter box Be sure to use the cable supplied with the converter box If the lamp is green the converter box is properly powered on A green light with a blank screen means that the digital signal is disconnected somewhere Check all the digital signal cable connections referring to the instructions in Chapter 2 for installing the converter box Cause 2 The monitor s EDID setting is incorrect Action 2 Set the correct value for your graphics card referring to the T221 Flat Panel Monitor Users Guide Cause 3 The converter box is connected only to the Connector B of the monitor Action 3 Connect the converter box to at least the Connector A of the monitor referring to the instructions in Chapter 2 Instead of one large screen two Cause 1 No converter box in use identical side by side screens Action 1 Use a converter box 12 P N 55P5776 are squeezed together Cause 2 The monitor has downlevel firmware that does not Or the text on the screen is support a converter box distorted and unreadable Action 2 Check the version of FPGA LOGIC as described in Chapter 1 Preparation for Installation Dual link that is a converter box cannot be used with downlevel versions of FPGA LOGIC Use a display mode and EDID setting that does not require a con
10. otection de la Directive 89 336 EEC du Conseil de l UE sur le rapprochement des lois des tats membres en matiere de compatibilit lectromagn tique IBM ne peut accepter aucune responsabilit pour le manquement aux exigences de protection r sultant d une modification non recommand e du produit y compris l installation de cartes autres que les cartes IBM Ce produit a t test et il satisfait les conditions de l quipement informatique de Classe A en vertu de CISPR22 Standard europ en EN 55022 Les conditions pour l quipement de Classe A ont t d finies en fonction d un contexte d utilisation commercial et industriel afin de fournir une protection raisonnable contre l interf rence d appareils de communication autoris s Avertissement Ceci est un produit de Classe A Dans un contexte r sidentiel ce produit peut causer une interf rence radio exigeant que l utilisateur prenne des mesures ad quates 17 P N 55P5776 Union Europea Normativa EMC Questo prodotto conforme alle normative di protezione ai sensi della Direttiva del Consiglio dell Unione Europea 89 336 CEE ull armonizzazione legislativa degli stati membri in materia di compatibilit elettromagnetica IBM non accetta responsabilit alcuna per la mancata conformit alle normative di protezione dovuta a modifiche non consigliate al prodotto compresa l installazione di schede e componenti di marca diversa da IBM Le prove effettuate sul p
11. resente prodotto hanno accertato che esso rientra nei limiti stabiliti per le le apparecchiature di informatica Classe A ai sensi del CISPR 22 Norma Europea EN 55022 I limiti delle apparecchiature della Classe A sono stati stabiliti al fine di fornire ragionevole protezione da interferenze mediante dispositivi di comunicazione in concessione in ambienti commerciali ed industriali Avvertimento Questo un prodotto appartenente alla Classe A In ambiente domestico tale prodotto pu essere causa di interferenze radio nel qual caso l utente deve prendere misure adeguate Unione Europea Directiva EMC Conformidad lectromagn tica Este producto satisface los requisitos de protecci n del Consejo de la UE Directiva 89 336 CEE en lo que a la legislatura de los Estados Miembros sobre compatibilidad electromagn tica se refiere IBM no puede aceptar responsabilidad alguna si este producto deja de satisfacer dichos requisitos de protecci n como resultado de una modificaci n no recomendada del producto incluyendo el ajuste de tarjetas de opci n que no sean IBM Este producto ha sido probado y satisface los lim tes para Equipos Inform ticos Clase A de conformidad con el Est ndar CISPR22 y el Est ndar Europeo EN 55022 Los limites para los equipos de Clase A se han establecido para entornos comerciales e industriales a fin de proporcionar una protecci n razonable contra las interferencias con dispositivos de comunicaci n licenciado
12. s Advertencia Este es un producto de Clase A En un entorno dom stico este producto podr a causar radiointerferencias en cuyo caso el usuario deber tomar las medidas adecuadas 18 LAU P N 55P5776 E CCI Statements for Other Countries AE BF AE jae FANS UE TENS REA HE Het h EHE BRERA BIS NER Copyright c 2003 International Display Technology Co Ltd All rights reserved 19
13. the dual link signal cable 55P5729 to the converter box It is only necessary to connect the USB cable 55P5728 to the converter box if you wish to use the monitor s Color Management Utility or Firmware Update Utility In this case the program s for either or both of those utilities must be installed prior to connecting the USB cable Important Do not connect the USB cable unless you are using the Color Management Utility or Firmware Update Utility Note The video input and video output are Safety Extra Low Voltage SELV circuits P N 55P5776 Fig 9 Connection of the Dual Link signal cable and the converter box Connect the opposite end of the dual link signal cable 55P5729 to the computer If the computer graphics card has another connector that supports DVI Single Link out or Dual Link out in addition to the DVI Dual Link connector connect the signal cable to the Dual Link connector The Dual Link oonnector is typically marked as 1 or A For details see your graphics card manual or computer manual The USB cable 55P5728 must also be connected to the computer to enable use of monitor s Color Management Utility or Firmware Update Utility USB connector gt USB cable 55P5728 DP Dual Link signal cable NL 55P5729 Video graphics card Fig 11 Connection of the Dual Link signal cable and a graphics card 10 P N 55P5776 Important If the connector is not properly inserted the
14. the monitor Such treatment could damage the monitor 2 1 Disconnecting the Existing Digital Signal Cable Power off both of the monitor and the computer Unplug the AC power cords of the monitor and computer from the wall outlets At the back of the monitor remove the stand rear cover and connector cover and disconnect the P N 55P5776 digital signal cable If two digital signal cables are attached disconnect both Disconnect the digital signal cable from the computer The disconnected digital signal cable is unnecessary with a converter box Store the cable away Important Connecting or disconnecting cables while the monitor or computer is switched on may damage the computer or graphics card 2 2 Connecting the Converter Box Display Signal Cables Computer Monitor Back side view Back side view B A DVI Dual Link Dual Link siga cable Converter signal cable 55P5729 Converter box 07N2230 07N2229 Fig 6 Dual Link Connect the end marked A of the converter signal cable 07N2229 to digital signal connector A at the rear of the monitor P N Converter signal cable 07N2229 y Cable hook Fig 7 Connection of the converter signal cable and the monitor 55P5776 Connect the other end marked 3 of the converter signal cable 07N2229 to the converter box Fig 8 Connection of the converter signal cable and the converter box Connect
15. verter box Cause 3 Wrong cable connected between the converter box and computer Action 3 Use the dedicated cable duaLhnk signal cable 55P5729 supplied with the converter box Action 4 Check the cable connections Cause 5 The monitor s EDID setting is incorrect Action 5 Set the correct value for your graphics card referring to the T221 Flat Panel Monitor Users Guide Restart the system after making any changes Left half of the computer screen Cause 1 Cable not attached properly is displayed down the center of Action 1 Check the cable connections the monitor screen Cause 2 You are using an unsupported graphics card or the device driver is downlevel Action 2 Check that the graphics card is a supported type and that the latest level device drivers are being used see the T221 Flat Panel Monitor Users Guide for further information amp details on how to access the web support page the computer screen interchange Action 1 Check the cable connections The sizes of the left half and Cause 1 Cable not attached properly the right half of the computer screen differ Cause 2 The graphics card setting is incorrect Action 2 Some graphics cards may require the video output setting changed by using a software program associated with the graphics card For details refer to the user s manual for the graphics card 13 The wrong display mode is Cause 1 The converter box is not connected to the proper
16. y Connect the power plug into an easily accessible outlet gt DANGER Sequence for connecting and disconnecting cables P N 55P5776 Electric current from the power cords and communication cables is hazardous To avoid any risk of electrical shock always connect and disconnect the cables as shown below when installing or moving the converter box or connected equipment or when connecting other equipment Connecting cables Disconnecting First attach the power cord and cables to the equipment Power everything off Bes a M E A da xt Z ED Next attach the signal cables to connectors gt eb P Lastly plug the power cord into a wall outlet i TE E Power everything on yes b 4 4 A Y Power everything off ji First unplug the power cord from the wall outlet ra Next disconnect all cables connectors from Lastly disconnect the power cord and cables from the equipment E End P N 55P5776 Contents Preparation tor Installation AA 6 1 1 Required System Configuration 6 1 2 Qhecking Patts i i iere te e Er 6 2 Connecting the Converter Bok erorri teet etie a oe tao Pete ead wee ae e La er T go Vo ee eee da 7 2 1 Disconnecting the Existing Digital Signal Cable 7 2 2 Connecting the Converter Box Display Signal Cables sse 8 PE A fd ma eere Eee t ety teet Te ER ee Edd
Download Pdf Manuals
Related Search