Husqvarna DS50 User's Manual
Contents
1. s manual People and animals can distract you causing you to lose control of the machine For this reason always remain concentrated and focused on the task Be careful as clothing long hair and jewellery can get caught in moving parts Transport and storage Do not store or transport the stand with the drilling machine fitted in order to protect your stand from damage Store the equipment in a lockable area so that it is out of reach of children and unauthorised persons Store the drilling machine and stand in dry and frost free conditions 6 English General working instructions Basic safety rules Do not use the machine in bad weather such as dense fog rain strong wind intense cold etc Working in bad weather is tiring and can lead to dangerous conditions e g slippery surfaces Never start to work with the power cutter before the working area is clear and you have a firm foothold Look out for any obstacles with unexpected movement Ensure when cutting that no material can become loose and fall causing operating injury Ensure that the working area is sufficiently illuminated to create a safe working environment Make sure that no pipes or electrical cables are routed in the area to be drilled Always check the rear side of the surface where the drill bit will emerge when drilling right through Secure and cordon off the area and make sure that no one can be injured or material damaged2. Hj Husqvarna Operators manual Please read the operator s manual carefully and make sure you understand the instructions before using the machine Manual de DS50 instrucciones Lea detenidamente el manual de instrucciones y aseg rese A I JA I S de entender su contenido antes de utilizar la m quina Bedienungsanweisung DS70 Lesen Sie die Bedienungsanweisung sorgf ltig durch und machen Sie sich mit dem Inhalt vertraut bevor Sie das AT Ger t benutzen GB ES DE FR Manuel d utilisation Lire attentivement et bien assimiler le manuel d utilisation avant d utiliser la machine HUSQVARNA CONSTRUCTION PRODUCTS KEY TO SYMBOLS Symbols on the machine WARNING The machine can be a dangerous tool if used incorrectly or carelessly which can cause serious or fatal injury to the operator or others Please read the operator s manual carefully and make sure you understand the instructions before using the machine Always wear Approved protective helmet Approved hearing protection e Protective goggles or a visor e Breathing mask This product is in accordance with applicable EC directives Ensure that water cannot leak into the machine when drilling in the ceiling Use an appropriate water collector and cover the machine in plastic but do not cover the air intakes and air outlets AEN SS AZ t The drilling machine must be suitable and designed for the size of
3. Never work alone always ensure there is another person close at hand Apart from being able to receive help to assemble the machine you can also get help if an accident should occur Keep all parts in good working order and ensure that all fixtures are properly tightened PRESENTATION Stand DS50 and DS70 It is our wish that you will be satisfied with your product and that it will be your companion for a long time Think of this operator s manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you will sell this machine make sure that the buyer will get the operator s manual A purchase of one of our products gives you access to professional help with repairs and services whenever this may be necessary lf the retailer who sells your machine is not one of our authorised dealers ask him for the address of your nearest service workshop Husqvarna Construction Products has a policy of continuous product development Husgvarna reserves the right to modify the design and appearance of products without prior notice and without further obligation introduce design modifications The stand features a modular design The stands are secured using expanding screws The drill column can be dismounted from the base plate This makes assembly easier The feeder housing s transmission is adj
4. SE 433 81 Partille Sweden tel 46 31 949000 declares under sole responsibility that the stands Husgvarna DS50AT and DS70AT from 2007 s serial numbers and onwards the year is clearly stated in plain text on the type plate with subseguent serial number are in conformity with the reguirements of the COUNCILS DIRECTIVES of June 22 1998 relating to machinery 98 37 EC annex IIA The following standards have been applied SE EN12348 The supplied stand conforms to the example that underwent EC type examination The stand must conform to applicable regulations EU reguirements as well as national reguirements Goteborg May 5 2006 mm RE Martin Larsson R amp D manager 14 English K Husqvarna www husgvarnacp com
5. that water cannot leak into the machine when drilling in the ceiling Use an appropriate water collector and cover the machine in plastic but do not cover the air intakes and air outlets 10 English MAINTENANCE Stand maintenance lt a UH Be The lifetime of your machine can be extended considerably if it is used cared for and maintained in the proper manner IMPORTANT All types of repairs may only be carried out by authorised repairmen This is so that the operators are not exposed to great risks Cleaning and lubrication IMPORTANT Remove the drill motor e Itis important that the drill stand is kept clean for functionality to be maintained Clean the stand using a high pressure washer and then wipe dry e Lubricate the moving parts on the stand Apply standard grease to counteract corrosion on the contact surfaces Daily maintenance 1 Check that nuts and screws are tight 2 Clean the outside of the machine 3 Check the slide function on the glide plates Change the glide plates if there is a backlash between the glide plates and the drill column Changing glide plates 1 Remove the drill motor 2 Remove the feeder housing from the column 3 Loosen the adjustment screws 5 Remove the glide plates 6 Lay down the stand 7 Mount a new lower glide plate on the column Fit the feeder housing on the column a
6. al applications by experienced operators e Keep the workplace tidy Disorder leads to accident risks Also read the operating manual enclosed with the drill motor and check that its performance is compatible with the stand Always use common sense It is not possible to cover every conceivable situation you can face Always exercise care and use your common sense Avoid all situations which you consider to be beyond your capability If you still feel uncertain about operating procedures after reading these instructions you should consult an expert before continuing Do not hesitate to contact your dealer or us if you have any more questions about the use of the machine We will willingly be of service and provide you with advice as well as help you to use your machine both efficiently and safely Let your Husqvarna dealer regularly check the machine and make essential adjustments and repairs All information and all data in the Operator s Manual were applicable at the time the Operator s Manual was sent to print WARNING Under no circumstances may the design of the machine be modified without the permission of the manufacturer Always use genuine accessories Non authorized modifications and or accessories can result in serious personal injury or the death of the operator or others Personal protective equipment WARNING You must use approved personal protective equipment whenever you use the machine Personal pr
7. drill bit max drill diameter is stated on the stand The drilling machine must conform to applicable regulations EU requirements as well as national requirements Other symbols decals on the machine refer to special certification requirements for certain markets 2 English Symbols in the operator s manual Inspection and or maintenance should be carried out with the motor switched off and the plug disconnected Always wear approved protective gloves Regular cleaning is required Visual check Protective goggles or a visor must be worn CONTENTS Contents KEY TO SYMBOLS Symbols on the machine 2 Symbols in the operator s manual 2 CONTENTS COMES A A in A a ang 3 WHAT IS WHAT What is what on the stand 4 SAFETY INSTRUCTIONS Steps before using a new stand 5 Personal protective equipment 5 General safety precautions 6 General working instructions 6 PRESENTATION Stand DS50 and DSTO sena nn Aan ters Z ASSEMBLY Assembling the stand ss nn Aa a 9 Assembly Of drill MOTOT sen nan nangka 9 Before drilling se da a a a a a aii 10 MAINTENANCE Stand maintenance sea 11 TECHNICAL DATA Dimension AA A AA ae a AAA 12 The column s a
8. nd fasten the lower glide plate on the feeder housing Mount a new upper glide plate on the column Fasten the upper glide plate on the feeder housing IMPORTANT The glide plates surfaces must be parallel 8 Fasten the rear clamping screws 4 Then fasten the front 4 clamping screws 9 Adjust the play between column and feeder housing with the adjustment screws English 11 TECHNICAL DATA Dimensions DS50 DS70 DS50 ATS DS50 mm inch DS70 mm inch 1 438 17 2 438 17 2 2 320 12 6 340 13 4 3 526 20 7 546 21 5 4 235 9 3 265 10 4 5 971 38 2 1026 40 4 6 1140 44 9 1205 47 4 7 177 7 0 8 231 9 1 9 1158 45 6 10 450 17 7 z Stroke mm inch Expander Max drill diameter mm inch DS50 DS70 DS50 0 676 0 26 6 Track width mm inch DS50 350 DS70 0 757 0 29 8 DS50 DS70 20 DS70 600 12 English The column s angling Weight NO oO FR WD Drill column Feeder housing Quick mounting Feed lever Feed lever Base plate Transport wheels Total weight without stabilizer Stabilizer TECHNICAL DATA DS50 kg Ibs 6 7 14 7 7 8 17 2 0 6 1 3 0 8 1 8 9 2 20 2 4 1 9 0 29 2 64 2 9 1 20 0 DS70 kg lbs 9 1 20 0 9 7 21 3 0 6 1 3 0 8 1 8 12 0 26 4 4 1 9 0 36 3 79 9 English 13 TECHNICAL DATA EC declaration of conformity Applies to Europe only Husqvarna Construction Products
9. ngling soseri na a akan 13 WEIDE nn Ae A A AAA ER 13 EC declaration of conformity 14 English 3 WHAT IS WHAT ey A tHusqvama What is what on the stand 1 Locking screw 17 Expansion attachment 2 Spirit level 18 Drill column 3 Locking screw locking clamp 19 Stop washer 4 Feeder housing lock 20 Locking clamp for quick mounting 5 Locking screw drill column 21 Mounting for feed lever 6 Position ring 22 Clamping screws for glide plates 7 Locking screw position ring 23 Quick mounting for automatic feed unit both sides of 8 Adjustment screws feeder housing Accessory 9 Locking screw angle drill column ee Operators manuel 10 Locking screw wheel 25 Retaining ring Accessory 26 Expander Accessory 27 Locking knob 1 Locking screw pivot function on drill column 12 Quick mounting 13 Lock button feed lever 28 Water collector Accessory 14 Feed lever 29 Distance Accessory 15 Handle 30 Stabilizer Accessory 16 Adjustment screw feeder housing against drill column St Tool kit 4 English SAFETY INSTRUCTIONS Steps before using a new stand Please read the operator s manual carefully and make Sure you understand the instructions before using the machine This machine is designed for and intended for drilling concrete brick and different stone materials All other use is improper e The machine is intended for use in industri
10. otective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen Ask your dealer for help in choosing the right equipment e Protective helmet e Hearing protection e Protective goggles or a visor e Tight fitting heavy duty and comfortable clothing that permits full freedom of movement e Boots with steel toe caps and non slip sole Always have a first aid kit nearby English 5 SAFETY INSTRUCTIONS General safety precautions e Please read the operator s manual carefully and make sure you understand the instructions before using the machine WARNING There is always a risk of crush injuries when working with products containing moving parts Wear protective gloves to avoid body injuries Never use the machine if you are tired if you have drunk alcohol or if you are taking medication that could affect your vision your judgement or your co ordination Wear personal protective equipment See instructions under the heading Personal protective equipment Never use a machine that is faulty Carry out the checks maintenance and service instructions described in this manual Some maintenance and service measures must be carried out by trained and qualified specialists See instructions under the heading Maintenance Never allow anyone else to use the machine without first ensuring that they have understood the contents of the operator
11. umn can be angled by loosening the locking screws with a 24 mm spanner e To angle the column parallel to the base plate loosen the screw on the positioning ring Assembly of drill motor HT EG 1 Lock the feeder housing on the drill column with the lock handle 3 Always remove the drill bit before the motor is mounted or dismounted 4 Mount suitable drilling machine on the quick mounting Mount the quick mounting and drilling machine in the track on the locking clamp 5 Fasten the locking clamp with the locking screw 6 Set the feed lever to a suitable transmission 7 Unlock the feeder housing 8 Start drilling See manual for selected drilling machine The slide function on the feeder housing is factory set To adjust the slide function see maintenance English 9 ASSEMBLY Before drilling WARNING Before drilling check that all locking screws are tightened well Serious accidents can occur if the concrete core remains in the drill when backing out the drill motor drill from the floor wall or ceiling WARNING If the vacuum plate is used make sure the support surface is not porous and can loosen from the floor or the wall Make sure that the vacuum pump has sufficient power to secure the vacuum plate The vacuum plate must never be used for ceiling drilling Careless or incorrect use can result in serious even fatal injury IMPORTANT Ensure
12. ustable The higher gives 2 5 1 and the lower 1 1 The feed lever can be mounted on both sides of the feeder housing The feeder housing is equipped with a quick mounting for a number of drilling machines The feeder housing s slide function on the column is adjusted with the 2 adjustment screws The stand makes angle drilling and pivot function possible Only fixed spanner 24 mm and hex key 6 mm are required to change the settings SZ The drill column can be variably adjusted through 360 The feeder housing is prepared for guick mounting for automatic feed unit which fits on both sides The transport wheels can be removed English 7 PRESENTATION Accessories Water collector Quick mounting for automatic feed unit both sides of feeder housing e Retaining ring e Expander e Distance Stabilizer For extra support o 8 English ASSEMBLY Assembling the stand 1 Drill holes 15 mm in the floor or in the wall and knock in the expander bolts 2 Screw the base plate tight Check carefully that the expander is secured correcily The drill column is mounted on the base plate s angle bracket Fasten the locking screw with a 24 mm spanner The drill column can be variably adjusted through 360 With help of the locking screw for the pivot function the column can be adjusted in four fixed 3 The col
Download Pdf Manuals
Related Search