Husqvarna GX560 User's Manual
Contents
1. R3 and fan R4 Inspect for damage and clean as necessary Fitting the Blade and the Fan Before using the lawnmower always visually inspect to see that blades and bolts are not worn or damaged Never use more than 2 cutting height spacers Spacers can only be fitted between the blade and the fan and never between blade and the bolt Ensure the fan is located correctly Place the spacers R3 onto the fan ensuring the pegs R5 have located into the holes R6 Place the blade R2 onto the spacers R3 ensuring the pegs R7 have located into the holes R8 on the blade and ensuring the blade is positioned as illustrated in Figure R Place the blade bolt R1 through the centre hole R9 of the blade Tighten down clockwise by hand Hold the fan firmly and tighten the blade bolt with the spanner provided Q An oily or carboned spark plug makes starting diffi cult and decreases the efficiency of the engine Periodically remove the spark plug and clean and adjust when necessary Cleaning the Air Filter Never run the engine without a filter or with a dirty filter This will greatly reduce engine efficiency and lead to engine damage Spark Plug Gap setting 0 028 0 031 Do not remove spark plug when engine is hot Do not sand blast the spark plug to clean it Air Cleaner Body Your lawnmower is fitted with an Air Cleaner the mainte nance for which is as2. H Husqvarna LL GX560 Operator s Manual cB Read the operator s manual careful ly and make sure that you under stand the contents before using the lawnmower 5119617 01 Carton Contents This product may have been purchased with a Wheel Assembly Please assemble your product in accordance with the relevant Instructions Wheel Assembly Kits are available from your local stockists GX560 Operator Presence Control Upper Handle Choke Control Lever Cable Tie Wrap Handle Knob Np j Washer Q Handle Knob Washer Cable Tie Wrap Lower Handle Lower Handle Retaining Clip Sp Hook Assembly wa a Lower Handle Pin Lower Handle Pin Lower Handle Retaining Clip Instruction Fuel Tap Booklet Wheel Frame if applicable 1 Lower Handle Wheels x 2 Upper telescopic tubes Telescopic tube pin Telescopic tube retaining clip Lower telescopic tubes Wheel retaining clips Wheel frame Hook Assembly Lower handle bolt x 2 Small washer x 2 Lower handle pin x 2 Large washer x 2 Locknut x 2 2 Safety If not used properly this lawnmower can be dangerous This lawnmower can cause serious injury to the operator and others the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower The operator is responsible for following the warning and safety instructions in this manual and on the lawnmower Exp
3. 6 Disconnect the spark plug lead the lawnmower slightly 7 Remove all fuel from the fuel tank 5 Once the engine has stopped release the Cleaning USE GLOVES Operator Presence Control e Keep your lawnmower clean grass clippings 6 Disconnect the spark plug lead left in any of the air intakes around the 7 Remove all fuel from the fuel tank engine or under the deck could become a 8 Remove the spark plug lead and spark plug Pour potential fire hazard one teaspoon 5ml of oil through the spark plug e Do not clean with chemicals including petrol or hole Pull the starting handle 2 or 3 times This will solvents some can destroy critical plastic parts distribute oil on the internal surfaces of the engine 1 Remove grass from under the deck with a piece Inspect clean and replace the spark plug If anew of wood or similar spark plug is required contact your local approved 2 Using a soft brush remove grass clippings from Electrolux Outdoor Products Service Centre Dealer around the engine and from all air intakes Do not re connect the spark plug lead 3 Remove the fan See Removing and Fitting 9 Clean the air filter See Cleaning the Air Filter the Blade and Fan and clean with a soft brush 10 Renew the blade if it is cracked damaged or 4 Wipe over the surface of your lawnmower with a bent Renew the blade bolt if necessary See dry cloth Removing and Fitting the Blade and Fan for Transporting your Lawnmower complete
4. follows 2 Check the filter before each use Clean every 25 hrs or more frequently when used in dusty areas Replace filter every 200 hrs Press the latch tabs on the top of the air cleaner cover and remove the cover Check the filter is clean and in good condition If the filter is dirty Tap the air filter several times on a hard surface to remove dirt or blow compressed air through the air filter from the clean side that faces the engine Never try to brush off dirt Brushing will force dirt into the fibers Wipe dirt from the air cleaner body and cover using a moist rag Be careful to prevent dirt from entering the air duct that leads to the carburetor Replace the filter and air cleaner cover Air Duct Air Cleaner Cover Latch Tabs Caring for your Lawnmower If you do not intend to use your lawnmower for long periods it is advisable to follow this proce dure after use 1 Stop the engine engine in a horizontal position Service your lawn 2 Fully close the fuel tap K mower after the last cut of the year as follows 3 Restart the engine At the end of the Mowing Season 4 As fuel runs out the engine will begin to stop tilt 1 Stop the engine the lawnmower slightly 2 Fully close the fuel tap K 5 Once the engine has stopped release the 3 Restart the engine Operator Presence Control 4 As fuel runs out the engine will begin to stop tilt
5. well known brands under various registered patents designs and trademarks in several countries Electrolux Outdoor Products Ltd Registered Office Electrolux Works Oakley Road Luton LU4 9QQ Registered number 974979 England 2 The Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world C We hope you find the links below useful For further gardening information visit www GardenResources co uk gsn cutters cullers Stusticutlers mowers chainsaws spreaders Garden tractors EE vacuums Hayter lawn Hedge cutters Hedgecutters mowers chainsaws cutters strimmers ates mowers tractors mowers tractors Mowers Chainsaws Spreaders EE Mowers STETE Cutters Strimmers Leaf Blowers Outes Mowers Heaters Heaters Covers Heaters Heaters Heaters Patio Heaters Heaters Covers fe a UOO Gardening Gifts Mowers Also See Gardening Tools Direct for lawn mowers brush cutters chainsaws Gardening Supply for patio heaters lawn mowers chainsaws Garden Tractor for lawn tractors and ride on mowers
6. Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP Certify that a sample of the above product has been tested using directive 81 1051 EEC as a guide The maximum A weighted sound pressure level recorded at oper ator position under free field semi ane choic chamber conditions was the undersigned M Bowden of Electrolux Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP Certify that a sample of the above product has been tested using ISO 5349 as a guide The maximum weighted root mean square value of vibration recorded at operator s hand position was No iShares aaa eb aac a aia GX560 Engine Manufacturet csceececeeeeeeeeeeeeeees Honda GCV160 Width of 1U eerremrerrrerte ene nee nPree nero Serer 50 5 cm Speed of Rotation of Cutting Device 3 300 RPM Guaranteed sound power level 99 dB A Measured Sound Power Level 5 97 0 dB A E a cb Gabanmnublaldducewetininn 86 8 dB A NS E E esse EE 3 3 m s Welg tuues aa a a 16 5 kg Newton Aycliffe 21 10 03 M Bowden Research amp Development Director Electrolux Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP ENGLAND Telephone 00 44 1325 300303 Fax 00 44 1325 310339 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice Electrolux Outdoor Products manufacture products for a number of
7. e a week in the growing season Your lawn will suffer if more than one third of its length is cut at one time Keep hands and feet away from the blade a rotat ing blade cannot be seen Mowing on banks and slopes can be dangerous Do not mow on steep slopes Always keep your feet on flat ground with the mower below you on the slope and with the spark plug uppermost to avoid lubricating oil running into the cylinder Do not use this mower on slopes which are wet or more than 45 from horizontal Never push the mower up the slope Removing amp Fitting the Blade amp Fan WARNING Always handle the blade with care sharp edges could cause injury USE GLOVES Spark plug lead may be hot handle with care Removing the Blade and Fan Renew your metal blade after 50 hours mow ing or 2 years whichever is the sooner regardless of condition If the blade is cracked or damaged replace it with a new one Ensure the Operator Presence Control is released when the engine has stopped and the blade has stopped rotating disconnect the spark plug lead Fully close the fuel tap L Turn your lawnmower on its side with the air cleaner uppermost see pic above To remove the blade bolt R1 hold the fan R4 firmly and with the spanner provided loosen the blade bolt by turning it anti clockwise Remove the blade bolt R1 blade R2 spacers
8. he engine has previously run dry a minimum of 400cc of fuel must be added to the level of the line indicated in diagram J to ensure correct priming of the fuel pump to start the engine Your carburettor is pre set Normally no further adjustment is required Oil Use 4 stroke automotive detergent oil SAE 10W 30 Fill with oil as instructed in your Engine Owners is recommended for general use Manual provided with your product Starting and Stopping To Start your Lawnmower Move the handle to the parking position C2 Connect the spark plug lead K Open the fuel tap L Move the Choke control lever to the Choke position M when starting from cold and to the Run position N when starting from hot 5 Pull and firmly hold the Operator Presence Control to the upper handle 6 Place your right foot firmly on the deck and grasp the top of the lower handle with your left hand Tilt the trimmer towards you P This ensures the product is in a secure position when starting and also prevents an unsightly ring being cut in your lawn 7 Pull the starting handle gently until you feel a resist ance return the starting handle slowly 8 Pull the starting handle firmly towards you to its full extent 9 Allow the engine to reach its full running speed then gently lower the lawnmower to the ground 10 When the engine has warmed up make sure the choke control leve
9. heel retaining clips F3 as illustrated in Fig F 3 Fit the wheel frame G1 to the deck with the lower handle bolt G2 small washer G3 large washer G4 and locknut G5 as illustrated in Fig G 4 Locate the lower telescopic tubes H1 inside the upper telescopic tubes H2 and secure with the pin H3 and retaining clip H4 as illustrated in Fig H Fit the Upper Handle to the Lower Handle by following the instructions above in Assembly without wheels section Handle Position The handle position can be adjusted using the guide and hook assembly 1 Lift hook C1 2 Position as required C2 Parking position C3 Mowing position Use a fresh clean unleaded regular automotive gasoline Do not fill the fuel tank in an enclosed area when the engine is hot or while you are smoking or near a naked flame Thoroughly clean around the fuel tank filler cap before filling this will help to prevent dirt being introduced into the fuel system Fuel should be stored in a cool place away from naked flames Do not fill the tank while the engine is running Fill the fuel tank through a funnel fitted with a fine filter Never fill fuel tank completely only fill to the base of the filler neck When filling the fuel tank from empty or when t
10. instructions e Turn the fuel tap to the off position and transport 11 Use only genuine Flymo parts and accessories with the engine in a horizontal position specified for this product e Never transport the lawnmower when it is run 12 Clean your lawnmower thoroughly See Cleaning ning 13 Your local approved Electrolux Outdoor Products Service Centre Dealer will carry out any service or repairs required 14 Store your lawnmower in a cool dry damp proof Storing Your Lawnmower Turn the fuel tap to the off position and store ina cool dry damp proof and safe place with the and safe place Fault Finding Engine Will Not Start 1 2 3 Ensure that the Operator Presence Control is gripped firmly to the upper handle Check that there is sufficient fuel in the fuel tank and the fuel tap is open Check that the choke control lever is in the cor rect position Run position N for a hot engine Choke position M for a cold engine The engine may have flooded Remove and dry the spark plug Petrol may be stale replace Once the petrol has been replaced it may take a little time for fresh petrol to filter through Check that the blade bolt is tight A loose blade bolt could cause difficult starting If the engine will still not start disconnect the spark plug lead and consult you local approved Service Centre Dealer Poor Flotation or Lack of Power Ae 2 3 4 Disconnect the s
11. lanation of Symbols on the GX560 Warning Read the user instructions carefully to make sure you understand all the controls and what they do Always keep the lawnmower on the ground when mowing Tilting or lifting the lawnmower may cause stones to be thrown out Keep bystanders away Do not mow whilst people especially children or pets are in the mowing area Beware of severing toes or hands Do not put hands or feet near a rotating blade Disconnect the spark plug before attempting any maintenance cleaning or adjustment or if you are going to leave the lawnmower unattended for any period Blade continues to rotate after the machine is switched off Wait until all machine compo nents have completely stopped before touch ing them General A Never allow children or people unfamiliar with these instructions to use the mower Local regulations may restrict the age of the operator 2 Only use the lawnmower in the manner and for the functions described in these instructions 3 Never operate the lawnmower when you are tired ill or under the influence of alcohol drugs or medicine 4 The operator or user is responsible for accidents or hazards occurring to other people or their property Fuel Safety WARNING Petrol is highly flammable Wear protective clothing when handling any fuels and lubricants Avoid contact with skin If affected wash liberally with soap and water Store fuel in a cool place in a con
12. park plug lead Clean the underside of the hood the air filter the fan around the engine and the air intakes Check that the engine choke control lever is in the Run position N Petrol may be stale replace Once the petrol has been replaced it may take a little time for fresh petrol to filter through If poor flotation or lack of power persists discon nect the spark plug lead and consult your local approved Service Centre Dealer Excessive Vibration 1 2 3 4 Disconnect the spark plug lead Check that the blade is correctly fitted See Fitting and Removing the Blade and the Fan If the blade is damaged or worn renew the blade If vibration persists do not use disconnect the spark plug lead and consult your local approved Centre Dealer Service Recommendations Your product is uniquely identified by a silver and black product rating label We strongly recommend that your product is serviced at least every twelve months more often in a professional application Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System ISO 14001 using where practical components manu factured in the most environmentally responsible manner according to company procedures and with the potential for recycling at the end of the products life Packaging is recyclable and plastic components have been labelled where practical for cate gori
13. r is in the Run N position To Stop your Lawnmower e Blade continues to rotate after the machine has switched off rotating blades can cause injury 1 Release the Operator Presence Control 2 As the engine dies tilt the lawnmower slightly This prevents a ring being cut in your lawn 3 When the engine has stopped lower the lawnmower to the ground 4 Put the handle in the Parking position C2 5 Close the fuel tap L Pan Before any servicing to the under side of your machine close the fuel tap let the engine run until it stops disconnect the spark plug lead and TIP THE MACHINE ON ITS SIDE WITH THE AIR CLEANER UPPERMOST Q Adjusting the cutting height Adjusting the Cutting Height 1 5 6 Never use more than 2 cutting height spacers Spacers can only be fitted between the blade and the fan and never between blade and the bolt R Ensure the Operator Presence Control is released when the engine has stopped rotating disconnect the spark plug lead Close the fuel tap L Turn your lawnmower on its side Remove the blade bolt R1 and blade R2 as described in Removing the Blade and Fan For a Lower Cut Add spacers R3 to a maximum of 2 For a Higher Cut Take spacers R3 away Refit the blade as described in Fitting the Blade and Fan How to Mow 1 Place the handle in the mowing position C3 2 Mow twic
14. ring adjustment of the machine to pre vent entrapment of the fingers between moving parts and fixed parts of the machine Assembly without wheels Fitting the Lower Handle to the Lawnmower 1 Feed the hook A2 attached to the lower handle A1 halfway through the centre slot of the guide A3 in the direction indicated by the arrow A4 2 Maintaining the hook A2 in the centre slot of the guide A3 turn the lower handle A1 clockwise through 90 to place both legs of the lower handle in position between the hood brackets A5 3 Insert the pins B1 and secure with the retaining clips B2 Fitting the Upper Handle to the Lower Handle BEFORE fitting the upper handle to the lower handle stabilize the lower handle by lifting the hook C1 to the parking position C2 1 Ensure the Choke Control Lever is on the left hand side when viewed from the rear 2 Align the lower and upper handle See fig D Locate the bolts D1 washers D2 and secure with the handle knobs D3 3 Fit the cables to the handles with the cable ties pro vided making sure the cables are not trapped between the upper and lower handles Assembly with wheels 1 Fit the lower handle E1 to the deck with the lower handle pin E2 as illustrated in Fig E 2 Attach the wheels F1 to the wheel frame F2 with the w
15. sed recycling Awareness of the environment must be consid ered when disposing of end of life product If necessary contact your local authority for dis posal information DISPOSAL OF FUELS AND LUBRICATING OILS Wear protective clothing when handling any fuels and lubricants Avoid contact with skin Remove petrol and engine oil before transporting the product Contact your local authority for information of your nearest Recycling Disposal Station Do NOT dispose of used fuels oils with household waste Do NOT dispose of used fuels oils to water Waste fuels oils are harmful but can be recycled and should be disposed of through the recognised facilities Do NOT incinerate Q EC Declaration of Conformity the undersigned M Bowden of Electrolux Outdoor Products Aycliffe Industrial Park NEWTON AYCLIFFE Co Durham DL5 6UP Certify that the Lawnmower Category Petrol Hover Make s 00 Electrolux Outdoor Products Conforms to the specifications of Directive 2000 14 EEC Type of Cutting Device Identification of Series Rotary Blade Notified BOY hse See Product Rating Label Conformity Assesment Procedure ANNEX VI I T S Cleeve Road Leatherhead Surrey KT22 7SB England Other Directives 98 37 EEC 89 336 EEC amp applicable standards EN836 1997 EN ISO14982 1998 the undersigned M Bowden of Electrolux Outdoor Products Aycliffe
16. tainer specifically designed for the purpose Use a fresh clean unleaded regular automotive petrol Use 4 stroke automotive detergent oil SAE 10W 30 is recommended for general use Refuel outdoors only and do not smoke while refuelling Wipe dirt and grass clippings from the fuel tank filler cap to avoid getting dirt into the fuel tank Add fuel BEFORE starting the engine Never remove the cap of the fuel tank or add fuel while the engine is running or when the engine is hot If petrol is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated Never use stale fuel left from last season or fuel which has been stored for long periods Replace all fuel tanks and container caps securely Move the product away from the fuelling area before starting Fuel should be stored in a cool place away from naked flames Your carburettor is pre set Normally no further adjustment is required Preparation i While using your product always wear substantial footwear and long trousers 2 3 4 The use of ear protection is recommended Make sure the area to be cut is clear of sticks stones bones wire and debris they could be thrown by the blade Before using the machine and after any impact check for signs of wear or damage and repair as necessary Replace worn or damaged blades together with their fixings in sets
17. to preserve balance Have faulty silencers replaced Use 10 11 12 13 14 15 16 17 Do not operate the engine in a confined space where exhaust fumes carbon monoxide can collect Use the mower only in daylight or good artificial light Avoid operating your mower in wet grass where feasible Take care in wet grass you may lose your footing On slopes be extra careful of your footing and wear non slip footwear Mowing on banks and slopes can be dangerous Do not mow on banks or_steep slopes Do not walk backwards when mowing you could trip Walk never run Never cut grass by pulling the mower towards you Release the Operator Presence control to stop the engine before pushing the mower across surfaces other than grass and when transporting the lawnmow er to and from the area to be mowed Never operate the lawnmower with damaged guards or without guards in place Do not overspeed the engine or alter governor settings Excessive speed is dangerous and shortens lawnmower life Keep hands and feet away from the cutting means at all times and especially when switching on the engine Do not tilt the mower when starting the engine except if the mower has to be tilted for starting In this case do not tilt more than absolutely necessary and lift only the part which is away from the operator Always ensure that both hands are in the operating position before returning the appliance to the ground Never pick
18. up or carry a lawnmower while the engine is running Spark plug lead may be hot handle with care Do not attempt any maintenance on your lawnmow er when the engine is hot Release the Operator Presence Control to stop the engine and wait until the blade has stopped before leaving the mower unattended for any period Release the Operator Presence Control to stop the engine wait until the blade has stopped disconnect the spark plug lead and wait until the engine has cooled before refuelling before clearing a blockage before checking cleaning or working on the appliance if you hit an object Do not use your lawnmower until you are sure that the entire lawnmower is ina safe operating condition if the lawnmower starts to vibrate abnormally Check immediately Excessive vibration can cause injury Maintenance and storage 1 2 3 Keep all nuts bolts and screws tight to be sure the lawnmower is in safe working condition Replace worn or damaged parts for safety Only use the replacement blade blade bolt spacer and impeller specified for this product Never store the lawnmower with fuel in the tank inside a building where fumes can reach an open flame or spark Allow the engine to cool before storing in any enclosure To reduce fire hazard keep the engine muffler and fuel storage area free of grass leaves or excessive grease If the fuel tank has to be drained this should be done outdoors Be careful du
Download Pdf Manuals
Related Search