Husqvarna C36C User's Manual
Contents
1. 1 4 4 4 i 1 N V y Pp a DRILL 11 32 HOLE2. OWNER MANUAL Model No C36C 36 Inch Mower Grass Catcher Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 140600 07 10 00 Rev rad 954 04 02 82 Printed in U S A SAFETY RULES A Safe Operation Practices for Ride On Mowers A IMPORTANT THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH GENERAL OPERATION Read understand and follow all instructions in the manual and on the machine before starting e Only allow responsible adults who are familiar with the instructions to operate the machine e Clearthe area of objects such as rocks toys wire etc which could be picked up and thrown by the blade e Besurethe area is clear of other people before mowing Stop machine if anyone enters the area e Never carry passengers e Do not mow in reverse unless absolutely necessary Always look down and behind before and while backing e Be aware of the mower discharge direction and do not point it at anyone Do not operate the mower without either the entire grass catcher or the guard in place e Slow down before turning e Never leave a running machine unattended Always turn off blades set parking brake stop engine and remove keys before dismounting e Turn off blades when not mowing e Stop engine before removing grass catcher or unclogging chu
3. DECK MANDREL STYLE B WHEEL WEIGHT CHUTE LATCH GRASS N CATCHER CONTAINERS LOWER CHUTE ATTACHING LOWER CHUTE STRAPS NOTE When right hand H H and left hand L H are mentioned in this manual it means when you are seated on the tractor in the operator s position 1 3 8 Wrench 1 Drive Ratchet 1 1 2 Socket 1 3 or longer Extension 1 9 16 Socket 1 Short Handle Phillips Screwdriver THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER CAUTION BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR Depress clutch brake pedal fully and set parking brake Place gearshift motion control lever in neutral N position Place attachment clutch in DISENGAGED position Turn ignition key OFF and remove key Make sure the blade and all moving parts have completely stopped Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug ASSEMBLY 1 MOWER DECK BAFFLE See Fig 1 COVER SEAL See Fig 3 Use Hardware GROUP A No hardware required e Raise your tractor mower deck to its highest position e Align mark on seal with mark at cover opening e Install the hex bolts locknuts and acorn nuts through e Worksealinto opening so cover sits between flanges of mower deck housing as shown seal e ightenall hardware securely ACORN NUT DISCHARGE GUARD ACORN NUT IN Lockuur ALIGNMENT LOCKNUT MARKS HE
4. RAMASSE HERBE NUMERO DE MODELE C36C PRODUCT NUMBER 954 04 02 82 NUMERO DE PRODUIT 954 04 02 82 YL REPAIR PARTS PIECES DE RECHANGE GRASS CATCHER MODEL NUMBER C36C RAMASSE HERBE NUMERO DE MODELE C36C PRODUCT NUMBER 954 04 02 82 NUMERO DE PRODUIT 954 04 02 82 KEY PART NO 2 3 4 NO 532069180 532127533 532161314 532128598 818021008 532140572 532087175 819061216 532007206 532060867 810071000 532109808 532125004 874930516 532130758 532128599 532133841 871161010 532132796 532133235 532132983 DESCRIPTION Locknut 10 24 Screen Cover Cover Asm Incl 3 38 39 Chute Upper Screw Special Indicator Dump Bag Screw 10 24 x 1 1 8 Washer 3 16 x 3 4 x 16 Ga Spacer Split Nut Acorn 10 24 Washer lock Latch Chute Nut Weld Bolt Hex 5 16 18 x 1 Latch Assy Bagger Chute Lower Nut Acorn 5 16 18 Screw 10 24 x 5 8 Spring Cover L H black Spacer Cover Spring Cover R H gray DESCRIPTION Ecrou frein Grillage de couvercle Couvercle Ens Y combris 3 38 39 Glissiere Sup rieure Vis sp ciale Indicateur de sac de d chargement Vis 20 24 x 1 1 8 Rondelle 3 16 x 3 4 x 16 Ja Entretoise fendue crou borgne 10 24 Rondelle frein Loquet de glissi re Axe du loquet Boulon H 5 16 18 x 1 Ensemble du loquet de ramasse herbe Glissi re inf rieure crou borgne 5 16 18 Vis 10 24 x 5 8 Ressort de couvercle C G Entretoise de couverc
5. assembly to tractor e Raise seat on tractor to allow assembly to be mounted e Withcover closed lift assembly and place support post inside mounting bracket Allow assembly to rest on lanced tabs of mounting bracket e Lineup holes in mounting bracket with holes in support post and insert bracket support pin Secure with retainer spring e Unlatch and open cover e Install the three 3 tubing end caps onto container support e Tap each end cap onto container support tubes to seat securely BRACKET SUPPORT PIN COVER ASSEMBLY RETAINER SPRING END CAP SUPPORT POST LANCED TABS MOUNTING BRACKET FIG 5 CONTAINER ASSEMBLY See Fig 6 No hardware required e Place bottom half inside of top half as shown e Placeonefootinside bottom half and lift top half to meet bottom half e Press halves tightly together while lifting top to lock into place as shown IMPORTANT BEFORE LOCKING THE TABS HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET e Repeat for second container CONTAINER BOTTOM HALF CONTAINER TOP HALF CONTAINER BOTTOM HALF PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF LOCKING TAB ASSEMBLY CHECK Squeeze sides of lower half of con tainer and check that there is no gap between upper and lower halves If a gap appears unlock tabs to separate container halves and repeat instructions above ASSEMBLY CONTAI
6. deterioration which could expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary 12 PREPARATION CAUTION BEFORE PROCEEDING WITH PREPARATION OF TRACTOR Depress clutch brake pedal fully and set parking brake Place gearshift motion control lever in neutral N position Place attachment clutch in DISENGAGED position Turn ignition key OFF and remove key Make sure the blade and all moving parts have completely stopped Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug NOTE ON SOME MODEL TRACTORS MINOR MODIFICATIONS MAY BE NECESSARY TO MOUNT YOUR NEW GRASS CATCHER NOT ALL MODEL TRACTORS WILL NEED THE FOLLOWING MODIFICATIONS CHECK CAREFULLY TO DETERMINE IF MODIFICATION IS REQUIRED ONCE YOUR MODEL TRACTOR CONFORMS TO THIS SECTION PROCEED TO ASSEMBLY To Prepare your Grass Catcher you will need 1 Drill Motor 1 11 32 Drill Bit DRILL HOLE IN MOWER DECK HOUSING See Fig 12 On some model tractors it may be necessary to drill holes in the mower deck housing If your mower deck does not have the holes Drill two 11 32 holes as shown NOTE Toassistin proper hole location there is atemplate in the back of this manual that may be used WE 20000000 DRILL HOLES FIG 12 13 REPAIR PARTS PIECES DE RECHANGE GRASS CATCHER MODEL NUMBER C36C
7. fall off and be seriously injured or interfere with safe machine operation e Keep children out of the mowing area and under the watchful care of another responsible adult Be alert and turn machine off if children enter the area Before and when backing look behind and down for small children e and down slopes 15 Max not across Remove obstacles such as rocks tree limbs etc e Watch for holes ruts or bumps Uneven terrain could overturn the machine Tall grass can hide obstacles e Use slow speed Choose alow gear so that you will not have to stop or shift while on the slope e Avoid starting or stopping on a slope If tires lose traction disengage the blades and proceed slowly straight down the slope e f machine stops while going uphill disengage blades shift into reverse and back down slowly e not turn on slopes unless necessary and then turn slowly and gradually downhill if possible A Safe Operation Practices for Ride On Mowers Look for this symbol to point out impor tant safety precautions It means CAU TION BECOME ALERT YOUR SAFETY IS INVOLVED CAUTION Do notcoast down ahillin neutral you may lose control of the tractor CAUTION Tow only the attachments that are recommended by and comply with specifications ofthe manufactu rer of your tractor Use common sense whentowing Operate only at the lowest possible speed when ona slope Too heavy of a
8. HOWN ACTUAL SIZE MOUNTING BRACKET TO DRAW BAR 4 Shoulder Bolt Self Tapping SUPPORT 3 Carriage Bolt 5 16 18 x 3 4 3 Locknut 5 16 18 GROUP D 1 Bracket Support Pin SUPPORT SUPPORT See 2 55 ax 55 RX RR SS RR 22220 II ES IIRIS MOUNTING 1 Retainer Spring BRACKET 3 Tubing End Caps LOWER CHUTE ASSEMBLY CHUTE LATCH ASSEMBLY to UPPER CHUTE CHUTE LATCH ASSEMBLY WHEEL WEIGHTS TO FRONT WHEELS BAG OF PARTS CONTENTS continued 2 Latch Hook Assembly 1222 G 2 Screw 10 x 5 8 2 Washer Lock 10 2 Washer 3 16 x 3 4 x 16 Ga 2 Nut Weld 10 ap Screw 10 x 1 1 8 1 Spacer Split 10 2 Washer 3 16 x 3 4 x 16 Ga 1 Nut Acorn 10 1 Rubber Latch mio d 1 Screw 10 x 5 8 1 Washer Lock 10 1 Washer 3 16 x 3 4 x 16 Ga 1 Nut Weld 10 ITEMS NOT SHOWN FULL SIZE TS J 4 Locknut ASSEMBLY BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some mower models may need minor modifications before you can mount the grass catcher to the unit Look carefully atthe mower deck on your unit and compare the deck mandrel to the illustrations below If your mower deck mandrel looks like STYLE A your unit is ready proceed with the grass catcher assembly If your mower deck mandrel looks like STYLE B go to the PREPARATION section in this manual DECK MANDREL STYLE A
9. NER MOUNTING See Fig 7 No hardware required e Install one container to left side first with warning to outside of unit Install other container to right side NOTE Rightcontainer should always overlap left container at center support e Close cover and lock latch handle over center support tube COVER LATCH HANDLE CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING 8 LOWER CHUTE See Figs 8A amp 8B Use Hardware GROUP E e Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw washer and lock washer as shown e Tighten hardware securely e Raise and hold deflector shield in upright position e Place front of chute over front of mower deck opening and slide into place as shown e Hook front latch into latch bolt on front of mower deck e Hook rear latch into latch bolt on back of mower deck when attaching lower chute and allow it to rest on chute while in operation CAUTION Do not remove discharge A guard from mower Raise and hold guard WASHER WASHER LOCK LOCK WASHER WASHER LATCH LATCH ae ACS NUT SCREW DEFLECTOR SHIELD CHUTE LATCH ASSEMBLY See Fig 9 Use Hardware GROUPS F amp G 9 e Assemble latch pin to upper chute as shown e Press weld nut into rubber latch and assemble rubber latch to lower chute as shown e Tighten all hardware secu
10. X BOLT 1 COVER SEAL FIG 1 FIG 3 2 REAR MOUNTING BRACKET See Figs 2A amp 2B SUPPORT POST See Fig 4 NOTE If your tractor already has four 4 shoulder bolts 4 Use Hardware GROUP C installed on the rear drawbar simply hang the mounting bracket lanced tabs towards bottom on the bolts Discard CAUTION Container supportis spring hardware group B and disregard the remaining Step 2 loaded and locked to the cover Handle Instructions cover assembly carefully so as not to unlatch the cover from the container support e Rotate cover assembly onto its side as shown e Assemble support post to container support with the three 3 carriage bolts and locknuts Tighten securely IT sHOULDER BOLTS LANCED TABS TOWARD BOTTOM CARRIAGE FIG 2A BOLTS If your tractor does not have four 4 shoulder bolts installed on the drawbar follow the instructions below Use Hardware GROUP B se Using the four formed holes in the drawbar install the four shoulder bolts as shown and tighten securely SUPPORT e Hang the mounting bracket lanced tabs towards bottom POST on the bolts SELF TAPPING SHOULDER FIG 4 LANCED TABS TOWARD BOTTOM ASSEMBLY MOUNTING TO TRACTOR See Fig 5 Use Hardware GROUP D NOTE For ease of assembly you may wish to obtain the assistance of another person for mounting
11. gine running Allow engine to cool before refueling Do not smoke Never refuel the machine indoors Never store the machine or fuel container inside where there is an open flame such as a water heater Never run a machine inside a closed area Keep nuts and bolts especially blade attachment bolts tight and keep equipment in good condition Never tamper with safety devices Check their proper operation regularly Keep machine free of grass leaves or other debris build up Clean oil or fuel spillage Allow machine to cool before storing Stop and inspect the equipment if you strike an object Repair if necessary before restarting Never make adjustments or repairs with the engine running Grass catcher components are subject to wear damage and deterioration which could expose moving parts or allow objects to be thrown Frequently check components and replace with manufacturer s recommended parts when necessary Mower blades are sharp and can cut Wrap the blade s or wear gloves and use extra caution when servicing them Check brake operation frequently Adjust and service as required SAFETY RULES e sure the area is clear of other people before mowing Stop machine if anyone enters the area e Never carry passengers or children even with the blades off e Donotmowin reverse unless absolutely necessary Always look down and behind before and while backing e Never carry children They may
12. ing e Disengage mower when crossing driveways or gravel surfaces and other areas where thrown objects could be a hazard e Donotattemptto vacuum up cans or other potentially hazardous projectiles CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any mainte When grass catcher is to be stored for a period of time clean nance it thoroughly remove all dirt grass leaves etc Store ina e Before each use check for loose fasteners clean dry place e Clean unit thoroughly after each use BLADE CARE CAUTION Donotleave grass in bagger For best results mower blades mustbe kept sharp Replace containers Empty containers aftereach bent or damaged blades useand IE Failure E us SO CARE instructions in your tractor owner s i ecu develop o ie REMOVE GRASS CATCHER CAUTION BEFORE PERFORMING ANY MAINTENANCE SERVICE OR ADJUST Reverse appropriate steps in ASSEMBLY section of this MENTS manual e Depress clutch brake pedal fully and set parking brake e Place gearshift motion control lever in neu tral N position e Placeclutchcontrolin DISENGAGED po sition e Turn ignition key to OFF position e Make sure blades and all moving parts have completely stopped e Disconnect spark plug wire s from spark plug s and place wire where it cannot come in contact with plug CAUTION Grass catcher components are subject to wear damage and
13. le Ressort de couvercle C D KEY PART NO NO 532127720 532063124 532124670 872140506 532170053 532170165 532131137 532174083 532126919 532128600 532127534 532129585 532129586 532130895 532155042 873800600 532137031 532123635 532104419 532140600 DESCRIPTION Post Support Locknut 5 16 x 18 Spring Retainer Bolt Carriage 5 16 18 x 3 4 Bracket Mounting Shoulder Bolt Self Tapping Pin Support Post Cap Tubing End Bagger Frame Pin Hinge Gasket Cover Container Top Container Bottom Latch Handle Cover Strip Reinforcement Locknut 3 8 16 U Bolt Weight Wheel Bag 3 0 mil 30 Gallon Trash not included with bagger Owner s Manual DESCRIPTION Poteau de soutien crou frein 5 16 x 18 Ressort de retenue Boulon de chariot 5 16 18 x 3 4 Support de montage Boulon Goupille de poteau de soutien Chapeau de l extr mit de tuyau Cadre de ramasse herbe Goupille de charni re Garniture de couvercle Sommet de conteneur Fond de conteneur Poign e de loquet de couvercle Bande crou frein 3 8 16 trier Poids de roue Sac poubelle 3 0 mil 30 gallon N y pas compris avec le ramasse herbe Manuel du propri taire 16 1 CUT OUT BOTH TEMPLATES AND PLACE IN POSITIONS SHOWN 2 MARK THE CENTER OF EACH HOLE AND DRILL WITH A 11 32 DRILL BIT y d V 4 4 4 DRILL 4 11 32 4 HOLE
14. load while on a slope is dangerous Tires can lose traction with the ground and cause you to lose control of your tractor CAUTION In order to prevent accidental starting when setting up transporting adjusting or making repairs always disconnect spark plug wire and place wire where it cannot contact spark plug CONGRATULATIONS on your purchase of a Grass Catcher Ithas been designed engineered and manufactured to give you the best possible dependability and performance Should you experience any problems you cannot easily remedy please contact your nearest authorized service center department They have competent well trained technicians and the proper tools to service or repair this unit Please read and retain this manual The instructions will enable you to assemble and maintain your Grass Catcher properly Always observe the SAFETY RULES NOTE To make debris disposal easier 30 gallon plastic trash bags may be inserted in plastic grass containers To order see repair parts section of this manual TABLE OF CONTENTS SAFETY RULES ise ee 2 3 BAGOF PARTS a 4 5 ASSEMBLY eat sas 6 OP RATION f sn 11 CUSTOMER RESPONSIBILITIES 12 STORAGE E 12 2 13 KNOW YOUR GRASS CATCHER READ THIS OWNER S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER Compare the illustrations with the carton conte
15. nts to familiarize yourself with the parts before starting the assembly Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others Save this manual for future reference WEAR YOUR The operation of any tractor can result in foreign objects thrown into the eyes which can result in severe eye damage Always wear safety glasses or eye shields before starting your tractor and while Pa mowing We recommend wide vision safety mask for over the spectacles or standard safety glasses THAN NO SIGHT UNPACKING INSTRUCTIONS CARTON CONTENTS e Remove all parts and packing materials from carton 2 Container Tops 1 Mounting Bracket e Fold flaps to inside of carton and turn carton upsidedown 2 Container Bottoms 1 Cover Assembly on floor of work area To protect grass catcher cover 1 Upper Chute 1 Cover Seal during assembly place cover upsidedown on overturned carton 1 Lower Chute 1 Bag of Parts e Checkcarton contents againstlist Be sure all parts are 1 Support Post 1 Owner s Manual there 2 Wheel Weights NOTE Forease of assembly aside of your work area lay out all hardware in the following groups Each step of the assembly instructions will identify the group needed for that step BAG OF PARTS CONTENTS ASSEMBLY LOCATION LATCH HOOK GROUP A ATTACHMENT Q 2 Locknut 5 16 18 Nut Acorn 5 16 18 HARDWARE S
16. pe If tires lose traction disengage the blades and proceed slowly straight down the slope DO NOT Do not turn on slopes unless necessary and then turn slowly and gradually downhill if possible Do not mow near drop offs ditches or embankments The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Do not mow on wet grass Reduced traction could cause sliding Do not try to stabilize the machine by putting your foot on the ground Do not use grass catcher on steep slopes lll CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them Keep children out of the mowing area and under the watchful care of another responsible adult Be alert and turn machine off if children enter the area Before and when backing look behind and down for small children Never carry children They may fall off and be seriously injured or interfere with safe machine operation Never allow children to operate the machine Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision IV SERVICE Use extra care in handling gasoline and other fuels They are flammable and vapors are explosive Use only an approved container Never remove gas cap or add fuel with the en
17. r grass catcher on a lawn where grass and leaf bagging equipment has not been used you are picking up thatch and debris that has accumulated for long periods of time The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher e Always run throttle at full soeed when bagging e Select a gear low enough to give good mower cutting performance good quality cutand good bagging perfor mance NOTE It may be necessary to overlap width of cut to suit your conditions e lfgrass is extremely tall it should be mowed twice The first time relatively high the second time to desired height e Use left hand side of mower for trimming e Plastic trash bags can be inserted inside grass catcher containers for ease of debris disposal To remove the plastic trash bags when full a Raise seat Unlatch and raise cover b Remove one container ata time by grasping contai ner handles and pulling toward the rear off of the tube rails c Withthe container resting on the ground close and secure the top of the plastic lawn bag d Tip the container on its side and slide the filled bag from the container e Install a new plastic lawn bag with the edges of the bag draped over upper lip of the Container for replacement bags refer to REPLACEMENT PARTS f Repeatfor other container g Reinstall containers making sure right container overlaps left container at center s
18. rely WASHERS 3 16 X 3 4 X 16 10 X 1 1 8 SCREW GA SPLIT SPACER UPPER CHUTE ACORN NUT 10 X 5 8 SCREW RUBBER LATCH LOWER CHUTE WELD NUT WASHER 3 16 X 3 4 X 16 GA LOCK WASHER FIG 9 ASSEMBLY 1 UPPER CHUTE See Figs 10A amp 10B 1 WHEEL WEIGHTS See Fig 11 No hardware required Use Hardware GROUP e Lower mower deck to its lowest cutting position Assemble wheel weights and U bolts onto the outside of e Assemble upper chute by inserting curved end into hole front wheels and hold in position in back of cover e Fastenlocknuts onto U bolts on the inside of wheel and NOTE Handle carefully so as not to damage dump bag tighten securely indicator e Pushin and turn upper chute until it is in line with lower LOCKNUTS FRONT WHEEL chute e Align the bosses on lower chute with alignment slots on upper chute and slide together xa e Secure with rubber latch by hooking hole in latch over latch pin DUMP BAGGER INDICATOR UPPER HANDLE CHUTE FIG 11 COVER PA 1 2 LEVEL MOWER DECK No hardware required e Be sure deck is properly leveled for best mower perfor mance See your tractors owner s manual for instruc tions FIG 10A ALIGNMENT SLOTS LATCH PIN RUBBER LATCH FIG 10B 10 OPERATION TIPS FOR IMPROVED BAGGING OPE RATION Follow the mower operation instructions in your tractor owner s manual When operating you
19. te e Mow only in daylight or good artificial light e not operate the machine while under the influence of alcohol or drugs e Watch for traffic when operating near or crossing roadways e Use extra care when loading or unloading the machine into a trailer or truck e Data indicates that operators 60 years and above are involved in a large percentage of riding mower related injuries These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury Il SLOPE OPERATION Slopes are a major factor related to loss of control and tipover accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not mow it DO e and down slopes not across Hemove obstacles such as rocks tree limbs etc e Watch for holes ruts or bumps Uneven terrain could overturn the machine Tall grass can hide obstacles e Use slow speed Choose alow gear so that you will not have to stop or shift while on the slope e Follow the manufacturers recommendations for wheel weights or counterweights to improve stability e Use extra care with grass catchers or other attachments These can change the stability of the machine e Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction e Avoid starting or stopping on a slo
20. upport h Close cover and secure latch over center support tube 11 Avoid cutting wet grass or in the morning while the dew is still heavy Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging Your bagger is equipped with a dump bag indicator As the bags become full the flow indicating ball will drop down in its slot indicating that the bags are full or the chutes have become clogged Care should be taken not to damage the parts and thatthe ball moves freely atthe beginning of each use If the grass catcher fails to pick up cut grass or leaves it is an indication that clogging has occurred in the system or that the grass catcher containers are full a Disengage blades shift into neutral engage the parking brake and stop the engine Raise seat Unlatch and raise cover Slide out containers and dispose of clippings Replace containers close cover and latch b Unlatch chutes and check for clogging Remove all debris in chutes Reassemble and latch chutes c Checktoinsure dump bag indicator has notbecome clogged The air passage hole must be clear of debris Gently insert a small twig or wire into passage way to clear A CAUTION e Do not operate mower with grass catcher partially installed e Disengage blades and stop engine before leaving tractor seatto empty containers unclog ging chutes etc e Close cover before start
Download Pdf Manuals
Related Search