Hunter 43553-01 User's Manual
Contents
1. Four Light Fixture Owner s Guide and Installation Manual Manual De Propietario For Your Records and Warranty Assistance For reference also attach your receipt or a copy of your receipt to the manual Where Purchased Table Of Contents 1 Installing the Light fixture on Fans With Removable Switch Housings 2 Installing the Light fixture on Fans With Non Removable Switch Housings 6 3 Installing the Light fixture on the Hunter Originals 4 Installing Bulbs and Shades 5 Troubleshooting 2009 Hunter Fan Company Welcome Your new Hunter light fixture is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your light fixture We are proud of our work We appreciate the opportunity to supply you with the best products available anywhere in the world Before installing your light fixture for your records and warranty assistance record information from the carton and Hunter nameplate label Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury install this light fixture only on Hunter fan types A through Z Note The fan type can be found on the ceiling fan package or on the nameplate label located2. 3 6 2 Installing the Light fixture on Fans With Non Removable Switch Housings Cont 9 Attach the light fixture to the switch housing with the two screws included with the light fixture aligning the holes in the i ls light fixture switch housing cover and switch housing L g i x A 10 Securely tighten the two screws D a 11 Go to the instructions for Installing the Bulbs and Shades 1 Wires 3 and Wire connectors 7 43553 01 05 15 09 Hunter Fan Company 3 Installing the Light fixture on the Hunter Originals Uninstall the two screws from the switch housing plate NOTE Save the switch housing plate should you choose to remove the light fixture in the future Remove the wire connectors from the two wires in the switch housing labeled Connect Light Here or For Light Use One wire is white and the other wire is black wire with a white stripe Thread the two wires through the hole in the center of the light fixture To connect the wires hold the bare metal leads together and place a wire connector over them then twist the wire connector clockwise until tight Connect the black white striped wire from the switch housing to the black wire from the light fixture Connect the white wire from the switch housing to the white wire from the light fixture Secure all wire connections using wire connectors CAUTION Be sure no bare metal wires or wire strands are visible after makin
3. g the connections Attach the light fixture to the switch housing with the two screws included with the light fixture aligning the holes in the fixture switch housing cover and switch housing Securely tighten the two screws Go to the instructions for Installing the Bulbs and Shades A WARNING Improper installation could cause the light fixture to fall or result in electrical shock or personal injury 43553 01 05 15 09 e Hunter Fan Company Switch Housing Vand Wire connectors 4 Installing Bulbs and Shades Install four purchased shades for the light fixture For each light loosen the three thumbscrews in the shade cup Place the shade into the shade cup and tighten the thumbscrews 2 Install the included CFL light bulbs 3 The installation is complete and you can restore power to the ceiling fan Steps 1 3 CFL bulb included 9 43553 01 05 15 09 e Hunter Fan Company 5 Troubleshooting Troubleshooting Light does not come on 1 Make sure bulbs are installed properly 2 Make sure breakers or fuses are on 3 Verify that the light power lead is connected at the ceiling Refer to your ceiling fan manual for locating assembly and wiring Glass rattles 1 Make sure the glass shades are secure If you need parts or service assistance please call 888 830 1326 In Canada call 866 268 1936 or visit us at our Web site at http www hunterfan com H
4. on Fans With Removable Switch Housings Unscrew the three screws from the upper switch housing Disconnect the 9 pin plug connectors Remove the lower switch housing Push the plug button from inside the lower switch housing to remove the plug button and switch housing cap NOTE Save the plug button and switch housing cap should you choose to remove the light fixture in the future Feed the two wires from the light fixture through the center hole in the lower switch housing Screw the threaded rod of the light fixture into the center of the lower switch housing until you feel resistance Unscrew the light fixture slightly until the holes of the light fixture are aligned with the holes in the lower switch housing Finish attaching the light fixture to the lower switch housing using the two attachment screws included Securely tighten the two screws Install the nut and washer inside the lower switch housing onto the threaded rod from the upper light housing Nut CD lt Washer K Lower Switch Housing Screw Steps 1 2 D 9 Pin Plug Connector ame Lower Switch Housing Plug Button A WARNING Improper installation could cause the light fixture to fall or result in a Qg Attachment Screws Steps 3 6 4 43553 01 05 15 09 Hunter Fan Company electrical shock or personal injury l Installing the Light fixture on Fans With Removable Switch H
5. on top of the motor housing of the ceiling fan e To avoid possible electrical shock before installing light fixtures disconnect the power by turning off the circuit breakers both to the outlet box and to its associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel e Connect house wiring to the fan before attaching the light fixture to the fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 2 43553 01 05 15 09 e Hunter Fan Company Installation Methods of Hunter Ceiling Fans Type A Z The Hunter Original Your AHanter light fixture can be installed in one of three ways depending on the type of switch housing The steps in this manual include instructions for all three installation methods Fans with removeable switch housings fans with non removeable switch housings and The Hunter Original Preparing the Light Fixture 1 Shades are not included with this light fixture Be sure to purchase shades for your light fixture before installing this light fixture 2 Disconnect power by turning off the circuit breakers both to the outlet box and to its associated wall switch location 3 43553 01 05 15 09 Hunter Fan Company l Installing the Light fixture
6. ousing Continued 7 Remove the wire connectors from the two wires in the switch housing labeled Connect Light Here or For Light Use To connect the wires hold the bare metal leads together and place a wire connector over them then twist the wire connector clockwise until tight Connect the black wire with a white stripe from the switch housing to the black wire from the light fixture Connect the 1 lt d Wie white wire from the switch housing to the white wire from the 7 OEA light fixture Secure all wire connections using wire connectors A CAUTION Be sure no bare metal wires or wire strands are visible after making the connections 8 Reconnect the 9 pin plug connector Reinstall screws to reattach the lower switch housing to the upper switch housing 10 Go to the instructions for Installing Bulbs and Shades Plug Connector A Steps 8 9 Housing Assembly Screw Lower Switch Housing Plug Connector gt Detail 5 43553 01 05 15 09 Hunter Fan Company 2 Installing the Light fixture on Fans With Non Removable Switch Housings Uninstall the two attachment screws from the switch housing cover Remove the plug or screw from the center of the switch housing cover Thread the switch housing cover onto the light fixture Align the screw holes in the light fixture with the screw holes in the switch housing cover Use the two attachment screws removed f
7. rom the lower switch housing and the lock washers on the red tag of the light fixture Install the screws into the light fixture and the housing Securely tighten the two screws Remove the wire connectors from the two wires in the switch housing Non Removable Switch labeled Connect Light Here or For Light Use One wire is white and the Housing other wire is black with a white stripe Feed the two wires from the switch housing through the threaded rod in the upper light housing To connect the wires hold the bare metal leads together and place a wire connector over them then twist the wire connector clockwise until tight Connect the black wire with a white stripe from the switch housing to the black wire from the light fixture Connect the white wire from the switch housing to the white wire from the light fixture Secure all wire connections using wire connectors Align the threaded screw holes in the switch housing cover with the threaded holes in the switch housing Attach the switch housin and light fixture to the switch I i AE E housing using the included Steps 1 2 Plug crew attachment screws Switch Housing CAUTION Be sure no bare CoverN a metal wires or wire strands are visible after making the connections Attachment A WARNING Improper installation could cause the light fixture to fall and Wire 1 connectors sj Light Fixture 43553 01 05 15 09 e Hunter Fan Company Steps
8. unter Fan Company 7130 Goodlett Farms Pkwy 400 Memphis Tennessee 38016 This Light Fixture Weighs 4 Ibs F Printed in China 43553 01 05 15 09 Hunter Fan Company
Download Pdf Manuals
Related Search