Huffy DCM230 User's Manual
Contents
1. Install rubber grommet 28 concave washer 29 and center lock nut 30 to carriage bolt 41 as shown Do not over tighten as rim will not flex properly See leveling instructions to determine how much to tighten nuts 42 and 30 P N 211446D 12 02 12 LEVELING INSTRUCTIONS Place level on rim 25 and adjust nut 42 until level Tighten nut 30 to set rim tension for playing C CD NE y r ww a p S WH yo Apply logo label 33 to cover plate 31 Install cover plate 18 on rim 25 using self tapping screws 32 as shown NOTE ORIENTATION OF COVER PLATE Secure net 34 to NOTE Official rim height is rim 25 10 3 05 m from top of rim to playing surface 10 feet 3 05 m 13 12 02 P N 211446D Check leveling at this time Pole should be level in all directions NOTE If adjustment is necessary adjust system by rotating the nuts 2 between mounting plate 3 and pole flange Refered to in Step 6 After system is leveled completely tighten nuts 7 above pole flange Apply height adjustment label 37 to front of pole as shown REGULATION RIM HEIGHT IS 10 FEET 3 05 m P N211446D 12 02 14 ADDING HEIGHT INDICATORS 27 Add height adjustment decal 35 A LOW2. with playing surface Clean off any excess cement on mounting plate at this time PLAYING SURFACE NOTE Check leveling of mounting plate 3 several times while concrete is curing IMPORTANT Front of mounting plate 3 must be parallel with playing surface WARNING DO NOT PROCEED TO STEP 6 UNTIL CONCRETE HAS CURED FOR A MINIMUM OF 72 HOURS ALLOW ADDITIONAL TIME FOR COLD WET OR HUMID WEATHER P N211446D 12 02 4 AWARNING THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Upright pole 5 Assemble lower pole flange onto protruding J bolts 1 as shown The flange will 6 then rest on the nuts 2 from Step 2 IMPORTANT Holes in pole must be parallel with playing surface PLAYING SURFACE 7 Secure pole 5 flange to mounting plate 3 as shown Tighten completely _ M IMPORTANT PLAYING SURFACE 12 02 P N 211446D Insert caps 8 into end of each support arm 9 amp 8 10 as shown Tap firmly in position AWARNING Apply logo label 11 to lower support arms 10 as shown Repeat for opposite side THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT Beginning with upper support arms 9 secure FOLLOWING RECOMMENDATION MAY 16 support arms to pole Continue by securing lower RESULT IN SERIOUS BODILY INJURY IMPORTANT ar Do not over tigh
3. 203218 Washer Flat 5 16 x 7 8 O D 920263 Rim Orange 201611 Bolt Hex Flange 5 16 18 x 3 203232 Washer 3 4 O D 220041 Grommet Rubber 220043 Washer Large Concave 201124 Nut Hex Locking 5 16 18 920043 Cover Plate Orange 220140 Screw Self Tapping 1 4 20 x 1 2 220569 Label Logo Circle 204282 Net 200787 Label Height Indicator 206555 Pole Pad May Not Be Included 200685 Label Height Adjustment 200655 Bolt Covers 920262 Bracket Orange 920038 Inner Bracket Black 220065 Bolt Carriage 3 8 x 5 1 2 203063 Nut Hex Nylon Locking 3 8 203017 Nut Hex 3 8 203439 Bolt Hex 3 8 x 6 220064 Spacer 5 x 1 2 O D x X09 4 N N N NN ARo SE SONG You May Have Extra Parts With This Model HARDWARE IDENTIFIER CS Item 7 10 Item 4 8 Item 16 4 Item 19 1 Item 26 4 Item 29 1 17 12 02 P N 211446D HARDWARE IDENTIFIER LD et AN UN e ju SAV Ci A et Item 23 4 Item 24 8 Item 27 5 Item 30 1 Item 32 2 OE OL OE Item 43 1 Item 42 2 Item 28 1 DU Item 41 1 Item 44 1 Item 45 1 P N211446D 12 02 18
4. result in system failure If technical assistance is required contact Huffy Sports Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 2 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as REQUIRED TOOLS AND pesticides herbicides or salts are all important MATERIALS Adult supervision is recommended when adjusting height Three People Serious injury could occur if teeth face come in contact with backboard net or rim Tape Measure Shovel and Post Hole Digger Use caution when using this system Carpenter s Level Two Step Ladder 8 ft 2 4 m Wrenches Two 1 2 9 16 3 4 15 16 One 3 8 Marker Vice Masking Tape For more information on assembly placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com IMPORTANT Have any questions Don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free
5. to approximately 7 2 1 m from ground Secure crank jack 20 to jack brackets 17 amp 18 as shown NOTE Some adjustment will be necessary to align the lower crank jack bushing to jack brackets 17 amp 18 REAR VIEW 10 RIM ASSEMBLY amp INSTALLATION Install carriage bolt 41 through rim 25 washers 4 and 27 as shown Tighten nut 43 completely Place nut 42 about half way up carriage bolt 41 as shown AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Apply foam pad 22 behind bracket 39 and attach bracket 39 to backboard and support structure by inserting bolts 26 and washers 24 through top holes in bracket 39 Tighten nuts 23 completely Insert inner bracket 40 into bracket 39 as shown Insert bolts 26 and washers 24 through top holes of inner bracket 40 as shown Tighten nuts 23 completely 11 12 02 P N 211446D 20 Insert spacer 45 through rim assembly 25 Place rim assembly on bracket 39 so that carriage bolt 41 is inserted through hole on top of inner bracket 40 Install hex bolt 44 washers 27 and nut 42 through top holes on bracket 39 through spacer 45 as shown Tighten completely BOTTOM VIEW
6. Customer Service Center V N53 W24700 South Corporate Circle HERI Sussex WI 53089 U S A A Huffy Sports Company WRITE IN YOUR MODEL NUMBER In Ground Basketball System Owners Manual SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly Check entire box and inside all packing material for parts and or additional instructional material Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document If using a ladder during assembly use extreme caution Three 3 people are reccomended for this operation Seat the pole sections properly Failure to do so could allow the pole sections to separate during play Before digging contact utility company to locate underground power cables gas and water lines Ensure there are no overhead power lines within 20 ft 7 m radius of pole location Climate corrosion excessive use or misuse could
7. Customer Service Number listed below Service will be quicker if you have your Model Number found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Toll Free Customer Service Number for U S 1 800 558 5234 Internet Address http www hydra rib com COPYRIGHT 1999 by HUFFY SPORTS 1 12 02 P N 211446D IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system See instruction manual for proper installation DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on pole When adjusting height keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc objects may entangle in net Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with with exterior enamel paint
8. ER BACKBOARD UNTIL RIM IS 7 FEET OFF THE GROUND B APPLY THIN WHITE STRIP TO BOTTOM EDGE OF OUTER CRANK TUBE AS SHOWN C APPLY LARGE DECAL TO BACK OF POLE SO THAT 7 FOOT MARK ON LARGE DECAL IS LINED UP WITH THIN WHITE STRIP 15 12 02 P N 211446D Secure pole pad 36 as shown NOTE Pole pad may NOT be included in this model Height Adjustment Rotate crank handle to raise and lower backboard NOTE If height adjustment is difficult to operate you may have over tightened the areas indicated Refer to Step 10 and Step 14 P N211446D 12 02 16 PARTS LIST Item Qty PartNo Description Item Qty PartNo Description 4 200573 J Bolt 5 8 11 24 12 265575 Nut Hex 5 8 11 25 920880 Mounting Plate 26 203470 Washer Flat 5 8 I D x 1 5 O D 27 980880 Pole 28 200544 Pole Cap Square 29 206340 Nylon Insert Lock Nut Hex 1 2 13 30 220589 Cap Arm Support Insert 31 916880 Support Arm 42 Long Upper 32 926880 Support Arm 52 Long Lower 33 220586 Logo Label 15 x 1 3 4 34 200574 Bolt Hex Flange 1 2 13 x 10 35 906880 Board Assembly 36 203474 Washer Flat 1 2 x 1 O D 37 201640 Bolt Hex 1 2 13 x 7 25 38 202856 Bolt Hex Head 1 2 13 x 4 39 900656 Bracket Jack Support Left 40 900658 Bracket Jack Support Right 41 206251 Bolt Hex 1 2 13 x 5 42 222880 Crank Jack 43 200576 Spacer Zinc 75 x 6 44 203274 Foam Pad 5x 5 45 203100 Nut Hex Flange 5 16 18
9. If rust has penetrated through the steel anywhere replace the pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before using Check system before each use for instability Never play on damaged equipment Keep pole top covered with cap at all times HYDRA RIS 1 800 558 5234 201255 2 99 Remove locking pin to remove handle Rotate crank handle to raise and lower backboard 200685 4 01 P N211446D 12 02 2 Ensure ground is level with playing surface then dig pole hole PLAYING AWARNING SURFACE BEFORE DIGGING GROUND SURFACE Install nut 2 to J bolt 1 as shown Repeat procedure for other three J bolts 1 IMPORTANT Make sure nuts are 2 5 08 cm from top of J Bolts 3 Install threaded ends of J bolts 1 through holes in mounting plate 3 and secure as shown NOTE Make sure J bolts 1 are in the illustrated position NOTE Nuts on the top of plate are used for leveling the pole after system is fully assembled 3 12 02 P N 211446D Fill hole with concrete Tamp down concrete to release air pockets and build drainage hill s Insert J bolts 1 from mounting plate 3 into cement as shown Move assembly around to release any air pockets in cement then rest mounting plate on cement drainage hill Apply some pressure to level mounting plate on top of drainage hill Level mounting plate and square
10. ten SHORT END IMPORTANT MAKE SURE TOP SET OF ELEVATOR ARMS ARE RESTING ON THIS MAUAL STOP BEFORE ATTACHING P N 2114460 12 02 6 1 Secure H frame board assembly to support arms 9 amp 10 AWARNING THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE IMPORTANT Do not over tighten 7 12 02 P N 211446D 12 Secure jack brackets 17 amp 18 to I holes i to lower holes in 4 pole as shown IMPORTANT HOLD HERE Position U joint of crank jack 20 as shown Where tubes on crank jack join hold steady to keep both tubes from rotating Rotate handle clockwise on crank jack to the fully extended position Upright crank jack P N 211446D 12 02 8 AWARNING THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Install crank jack 20 U joint to lower set of support arms 10 as shown REAR VIEW 9 12 02 P N 211446D P N 211446D 12 02 s AWARNING THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Rotate jack handle clockwise to raise H frame 13
Download Pdf Manuals
Related Search