HP SSL2020 Reference Guide
Contents
1. rear of the unit see Figure 2 cc0019 Figure 2 Outside cover screw locations rackmount version Outside Cover Removal Procedures 1 Turn off power to the AIT Library and then unplug it from the AC power source 2 Remove the appropriate screws that secure the outside cover to the unit 3 Slide the outside cover toward the rear of the unit until it clears the lip behind the front panel 4 Lift the outside cover up and away from the unit 5 Save the hardware for re use 4 Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide Removing the Brace Plate and Upper Drive Mounting Plate The brace plate and upper drive mounting plate must be removed to gain access to the drive area To remove both plates 1 Remove the outside cover 2 Remove the four screws that secure the brace plate to the chassis 0 Figure 3 Figure 3 Brace plate removal Adding a Second Drive 5 3 Remove the screws that secure the upper drive mounting plate to the chassis see Figure 4 4 Lift out the upper drive mounting plate Figure 4 Upper drive mounting plate removal 6 Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide Installing Alignment Pins Four alignment pins need be installed into the new drive prior to installation Each alignment pin consists of a plastic spacer top hat and a screw Figure 5 To install the alignment pins 1 Place a plastic spacer onto each2. Compaq StorageWorks SSL2000 Series Librarv Drive Upgrade Reference Guide First Edition April 2000 Part Number 187194 001 Compaq Computer Corporation Notice 2000 Compaq Computer Corporation Compaq the Compaq logo and StorageWorks Registered in U S Patent and Trademark Office All other product names mentioned herein may be trademarks or registered trademarks of their respective companies Compaq shall not be liable for technical or editorial errors or omissions contained herein The information in this document is subject to change without notice The information in this publication is subject to change without notice and is provided AS IS WITHOUT WARRANTY OF ANY KIND THE ENTIRE RISK ARISING OUT OF THE USE OF THIS INFORMATION REMAINS WITH RECIPIENT IN NO EVENT SHALL COMPAQ BE LIABLE FOR ANY DIRECT CONSEQUENTIAL INCIDENTAL SPECIAL PUNITIVE OR OTHER DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION EVEN IF COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THE FOREGOING SHALL APPLY REGARDLESS OF THE NEGLIGENCE OR OTHER FAULT OF EITHER PARTY AND REGARDLESS OF WHETHER SUCH LIABILITY SOUNDS IN CONTRACT NEGLIGENCE TORT OR ANY OTHER THEORY OF LEGAL LIABILITY AND NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY The limited warranties for Compaq products are exclusively set forth in the docume
3. an access the Compaq website at http www compaq com Compag Authorized Reseller For the name of your nearest Compaq authorized reseller m In the United States call 1 800 345 1518 m In Canada call 1 800 263 5868 m Elsewhere see the Compaq website for locations and telephone numbers Adding a Second Drive Introduction This guide explains how to add a second tape drive to the Compaq Storage Works SSL2000 Series Librarv AIT Librarv IMPORTANT All screws that do not use lock washers captive washers or lock nuts must have Loctite 222 applied when parts are reassembled in the field If you ignore this step you might cause premature failure of the mechanism This chapter includes procedures for m Removing the outside cover E Removing the brace plate and upper drive mounting plate m Installing alignment pins a Installing the new drive 2 Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide Removing the Outside Cover This section describes how to remove the outside cover from both the tabletop and rackmount versions of the Compaq StorageWorks SSL2000 Series Library Outside Cover Screw Locations The outside cover for the tabletop version is held in place by four screws at the sides of the unit see Figure 1 Figure 1 Outside cover screw locations tabletop version Adding a Second Drive 3 The outside cover for the rackmount version is held in place bv two screws at the top
4. e leveling jacks m The stabilizing feet are attached to the cabinet if it is a single cabinet installation The cabinets are coupled together in multiple cabinet installations Only one component is extended at a time A cabinet may become unstable if more than one component is extended for any reason Getting Help If you have a problem and have exhausted the information in this guide you can get further information and other help in the following locations Compaq Technical Support In North America call the Compaq Technical Phone Support Center at 1 800 OK COMPAQ This service is available 24 hours a day 7 days a week For continuous quality improvement calls may be recorded or monitored Outside North America call the nearest Compaq Technical Support Phone Center Telephone numbers for world wide Technical Support Centers are listed on the Compaq website Access the Compaq website at http www compaq com Be sure to have the following information available before vou call Compaq Technical support registration number if applicable Product serial number Product model name and number Applicable error messages Add on boards or hardware Third partv hardware or software Operating svstem tvpe and revision level viii Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide Compaq Website The Compaq website has information on this product as well as the latest drivers and Flash ROM images You c
5. electrical shock hazards do not open this enclosure AG Any RJ 45 receptacle marked with these symbols indicates a Network Interface Connection WARNING To reduce the risk of electrical shock fire or damage to the equipment do not plug telephone or telecommunications connectors into this receptacle AA Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component If this surface is contacted the potential for injury exists WARNING To reduce the risk of injury from a hot component allow the surface to cool before touching A Power Supplies or Systems marked with these symbols indicate the equipment is supplied by multiple sources of ames om T WARNING To reduce the risk of injurv from electrical shock remove all power cords to completelv disconnect power from the svstem AA Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely WARNING To reduce the risk of personal injury or damage to the equipment observe local occupational health and safety requirements and guidelines for manual material handling About This Guide vii Cabinet Stabilitv A WARNING To reduce the risk of personal injury or damage to the equipment be sure that m The leveling jacks are extended to the floor m The full weight of the cabinet rests on th
6. nnzznenznznna 5 Figure 5 Alignment pin installation sse nnnnnenennnnnnnnnnnnnn nem nanna 6 Figure 6 Installing the new drive eennnnnenenennnnnnnnn nases nesa nn n tna 7 Figure 7 Connecting the new drive nenenennzenznnnennnznnnnnnnnnnn anna nn 8 About This Guide This guide is designed to be used as step bv step instructions for installing a second drive into a Compaq StorageWorks SSL2000 Series Library Symbols in Text These symbols may be found in the text of this guide They have the following meanings WARNING Text set off in this manner indicates that failure to follow directions L in the warning could result in bodily harm or loss of life 7 CAUTION Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information IMPORTANT Text set off in this manner presents clarifying information or specific instructions NOTE Text set off in this manner presents commentary sidelights or interesting points of information vi Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide Symbols on Equipment These icons may be located on equipment in areas where hazardous conditions may exist AAS Any surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards Enclosed area contains no operator serviceable parts WARNING To reduce the risk of injury from
7. ntation accompanying such products Nothing herein should be construed as constituting a further or additional warranty Printed in the U S A Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide First Edition April 2000 Part Number 187194 001 Contents About This Guide Symbolsin Textron wad o a Ta v Symbols on Equipment sern E E S A AE A OEE RS vi Cabinet Stability esr n Ai A beds la ez ed kee p b i R ANENE vii Getting Help ss issib i iba a fta das sw f da tt a a ati vii Compaq Technical Support nnnenennnnnnennn nanna nesa nanna vii Compa Website ca een ete a p b ta i pest plot Si Bed pub shee Save 2 vili Compaq Authorized Reseller misiismo eiai ners EA viii Adding a Second Drive Introductio Maei e a r ee Ae ea a 1 Removing the Outside Covet enee E E EASO RRR 2 Outside Cover Screw Locations sinsicniiiisiecnni iain inina 2 Outside Cover Removal Procedures nee nenenennnnnn en nenn sea 3 Removing the Brace Plate and Upper Drive Mounting Plate mm 4 Installing Alignment Pins nn E nenn nases ann nanna stenna 6 Installing the New Drive i isco idea ee pig ssa bba za dos aa Best iU 7 List of Figures Figure 1 Outside cover screw locations tabletop Version seen 2 Figure 2 Outside cover screw locations rackmount Version ss sseeeseensenezza 9 Figure 3 Brace plate removal isse zin ji iesiiu And si see e sabe ssp eb et 4 Figure 4 Upper drive mounting plate removal eee eennnnennznnnzz
8. of the four screws 2 Install the alignment pins at the locations shown Figure 5 cc0022 Figure 5 Alignment pin installation Adding a Second Drive 7 Installing the New Drive To install the new drive 1 Align the new drive with the holes at the bottom of the chassis 2 Lower the new drive into the chassis see Figure 6 cc0023 Figure 6 Installing the new drive 8 Compaq StorageWorks SSL2000 Series Library Drive Upgrade Reference Guide 3 Connect the power cable 0 serial cable and SCSI cable to the new drive see Figure 7 cc0024 Figure 7 Connecting the new drive 4 Secure the upper drive mounting plate to the new drive and chassis using the previously removed retaining screws Secure the brace place to the chassis using the previously removed retaining screws Place the outside cover onto the chassis and then slide it forward until it is flush with the front panel Secure the outside cover to the chassis using the previously removed SCrews Connect the AIT Library to an AC power source Turn the AIT Library on and test the operation of the new drive
Download Pdf Manuals
Related Search