Home

HP Server tc2100 Installation Guide

1. Driver s Installation e Phase 2 Hard Drive Preparation e Phase 3 System Configuration Details e Phase 4 Configuring the Network e Phase 5 Completing the Installation e Phase 6 Install the Service Pack e Phase 7 Install the HP Video Driver NOTE Do not try to install Windows NT 4 0 via booting from the Windows NT CD ROM This method of installation does not work properly on most servers The installation procedure will prompt you to insert the Windows NT CD ROM at a later time Chapter 2 Installing Microsoft Windows NT 4 0 Server PHASE 1 Drivers Installation 1 8 Insert the Windows NT Setup Boot Diskette 1 and boot the system 2 Replace the diskette when prompted and press Enter 3 4 Ifyou have a SCSI model Once under Windows NT Server Setup menu press Enter to continue a Press S to skip mass storage detection and manually select SCSI adapters b Press S again to specify additional SCSI adapters The Windows NT installer will display a scrolling list of options c Press Enter to select the default option Other Requires Disk provided by a hardware manufacturer d When prompted to insert the Manufacturer supplied hardware support disk insert the HP Server tc2100 Windows NT SCSI driver HP disk NT 1 into floppy drive then press Enter e Press Enter to select the Adaptec Ultral60 Family PCI SCSI controller Press S again to install the IDE CD ROM driver a Press th
2. Method 1 Method 2 Method 3 Insert CD in your new HP server and reboot it This will run HP Diagtools a DOS program Insert the CD ina Windows or Linux PC Open the file start htm This allows you to access manuals and create drivers diskettes HTML menus and PDF files Requires PC with browser and Adobe Acrobat Reader Insert the CD in the server once the NOS is running Open the file start htm This allows you to access manuals create drivers diskettes and provides an automated installation of Windows NT or 2000 video drivers HTML menus and PDF files Requires PC with browser and Adobe Acrobat Reader This method is not available on NetWare servers since they don t have an HTML browser 2 Installing Microsoft Windows NT 4 0 Server Prepare the Installation Please refer to the Chapter 1 Preparing your HP Server tc2100 for your NOS installation for our recommendations on the server preparation Then gather the following material HP Server tc2100 Startup CD Microsoft Windows NT4 CD ROM as well as the latest Microsoft NT Service Pack 6a or above Six blank formatted 3 5 inch diskettes Two or more clients for testing purpose Optional To avoid problems use only hardware that appears on the Windows NT Hardware Compatibility List HCL You can access the latest HCL via Microsoft s Web site at http www microsoft com ntworkstation High Level Process F
3. a From one of the clients open a command prompt and type ping computername Where computername is the server name you entered during Windows NT installation You should get four reply s from your new server If there is a link problem it must be fixed before going any further You may test the link further by doing a ping between two clients at the same command prompt type ping other client IPaddress You should get four reply s from the second client b Copy files back and forth from the clients to the server Testing the connection using Terminal Services 24 1 Click Start Programs Terminal Services Client Terminal Services Client on a client you installed Terminal Services on Select the target server from the Available Servers list provided on the screen Click the Connect button Chapter 3 4 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Complete the UserID Password login form PHASE 3 Domain Controller Setup The Windows 2000 reference guide calls this process Promoting the server to a domain controller 1 Click Start Programs Administrative Tools Configure Your Server to open the Windows 2000 Configure Your Server window 2 Select Active Directory 3 Scroll down and click Start the Active Directory wizard 4 Click Next to continue NOTE The following instructions corresponds to the standard steps for new domain creation You may c
4. l Create shares create a folder on your hard drive then share it right click on folder and the select Sharing Create users using Windows NT utility Start Programs Administrative Tools User Manager DOMAIN 11 Chapter 2 Installing Microsoft Windows NT 4 0 Server Connect clients PC to the network your HP server operates on Open a command prompt window on your HP server Start Program Command Prompt and verify the TCP IP configuration you have set during Windows NT installation by entering ipconfig all To verify the server and clients can communicate properly a From one of the clients open a command prompt and type ping computername Where computername is the server name you entered during Windows NT installation You should get four reply s from your new server If there is a link problem it must be fixed before going any further You may test the link further by doing a ping between two clients at the same command prompt type ping other client IPaddress You should get four reply s from the second client b Copy files back and forth from the clients to the server Section 7 Installing Additional Adapters Drivers Ethernet Adapter We will use here as an example the installation of an additional HP 10 100TX PCI LAN Adapter HP product number D5013B this HP accessory is supported on your HP Server tc2100 1 2 3 12 Open Start Settings Control Panel Network Adapters S
5. then Enter again to confirm the Network Adapters selection Follow the on screen instructions to complete the selection of the Network Protocols and Network Services Chapter 2 Installing Microsoft Windows NT 4 0 Server NOTE The network settings need to be customized to your environment Please refer to Microsoft NT Server manuals should you need further details on the networking settings 6 Click Next to install all above selected components when prompted by Windows NT Server Setup NOTE If you choose to specify a IP address and skip the installation of the DHCP component Windows NT Server installation will open Microsoft TCP IP Properties window where you should enter your IP address You may configure this IP address again after completion of the Windows NT install by selecting Start Settings Control Panel Network Protocols TCP IP Protocol Properties 7 Click Next at the Network Bindings window to keep the default services 8 Click Next to start the Network 9 Click Next to confirm the Domain your server will operate in PHASE 5 Completing the Installation 1 Choose Finish to perform the last installation step 2 Windows NT Server 4 0 will then proceed with the installation of Microsoft Internet Information Server 2 0 a Press Enter to keep default setup options then Enter again to confirm creating the corresponding installation directory b Press Enter to keep default publishing directories then Enter
6. 1 On Line Information and Software Sources e HP World Wide Web access http www hp com e Red Hat World Wide Web access http www Red Hat com e Red Hat Errata World Wide Web access http www Red Hat com errata 43 6 Installing TurboLinux Server 6 5 Prepare the Installation Please refer to the Chapter 1 Preparing your HP Server tc2100 for your NOS installation for our recommendations on the server preparation Then gather the following material e HP Server tc2100 Startup CD e TurboLinux Server 6 5 CD ROM e A blank 3 5 inch diskette labeled TurboLinux 6 5 Boot Disk Optional e Two or more clients for testing purpose Optional High level process flow 1 Perform TurboLinux 6 5 installation 2 Attach clients to network and test network link Perform TurboLinux Installation PHASE 1 Launch the Installation 1 Turn on the server and insert the Turbolinux Server 6 5 CD ROM 2 Press Enter to start installation 3 Wait as the system prepares for the installation 4 Choose your language then press Enter to proceed with the installation PHASE 2 Configure the Server The installation program now displays a graphical interface You can proceed through the customization of your installation Please note the following recommendations e HP recommends using the default Install Class which is Standard Install 45 Chapter 6 Installing TurboLinux Server 6 5 e Your HP server comes with a Gen
7. 3 Perform Windows NT Installation c ccecceeeeeeeeeeeceeeeeeeeeeteees 4 PHASE 1 Drivers Installation 0 cccecceceececeeeeeeeceeeeeeeeeeeeeeeeneeeeeeeeeeeees 5 PHASE 2 Hard Drive Preparation ccccceeeeeeeeceeceeeeeeeeeeeeenieeeeeeeeeeees 5 PHASE 3 System Configuration Details 2 00 00 ccceeeeeeeeeeeeteeeeeeeneeeeteaes 6 PHASE 4 Configure the Network ccccceeeeseeeeeeeneeeeeeneeeeeeneeeeeeneeeeeeaas 7 PHASE 5 Completing the Installation 0 ccceeseseeeeeeeeeeeeeneeeeeenieeeeeeaas 8 PHASE 6 Install the Service Pack ccccccccceceeeseceecneceeeeeeesecenaeeeeeeeees 9 PHASE 7 Install HP Video Driver ccc ccecceceeeeeeeeeecaeeeeeeeeeseestaeeeeees 10 Section 4 Initialize Hard disk Drive cccccccceceeeeeeeeeeeeeeeeeeeeeeetneeeeeeeeteees 10 Section 5 Perform Hardware Status Check c ccesceeeeeeeeeeeeneeeeseenteeeeeeaas 11 Section 6 Attach Clients to Network and Test Network Link 11 Section 7 Installing Additional Adapters Drivers c ccceseeeeseeeeeeesteeeeeaes 12 Ethernet Adapter e i a a a a a a E aa aa ARa 12 HP NetRAID 1M Adapter ccccccececccceeseccceenseccetesseceeeeneeeceeeeseeeeeeneeceaenees 13 Troubleshootihg nsina A EAEE 13 Tip 1 Troubleshooting SCSI Host Bus Adapter Configuration 13 Tip 2 NT Warning About Drives with More than 1024 Cylinders 14 Tip 3 Service
8. Log for any driver diagnostic messages 1 Start the Event Viewer applet in the Administrative Tools group in Program Manager 2 Search the Event Log Source column for any entries named Hptx 3 Double click on the entry to examine the Event Detail dialog box The upper half of the box gives a short generic description of the error The lower half of the box is a hex and ASCII dump of error data 4 Scroll through the error data in ASCII for any readable strings 5 Ifa readable string is present it will describe the problem in more detail 6 Ifno readable string is present this typically indicates that the driver failed early in the process of loading usually due to a resource conflict for example an I O port conflict NOTE Make sure the Network Adapter is connected to a working hub and verify that the LED is lit Otherwise the Network Driver may not install Tip 5 Booting from Another SCSI HDD To boot Windows NT from another SCSI hard disk press Ctrl A during system boot to enter SCSI Select menu In this menu configure the SCSI Hard Drive Priority option in the Boot Device Ordering menu Tip 6 Restarting Windows NT installation If you want to restart Windows NT installation from the very beginning use a utility such as fdisk to erase all data and partitions from your hard drive Then resume all installation process 15 Chapter 2 Installing Microsoft Windows NT 4 0 Server On Line Information and Software
9. Pack Files Replaced Without Feedback 000 15 Tip 4 Using the NT Event Log to Diagnose Network Adapter Problems 15 Tip 5 Booting from Another SCSI HDD 0 000 eeeeeeeeeeeeeenteeeeeeneeeeeeaas 15 Tip 6 Restarting Windows NT installation 0 0 0 cccceeeeeeeeeeeeeeeeteeeeeeaes 15 On Line Information and Software Sources c ceeeeeecceceeeeeeeeeeeeeeeeeeeeeeees 16 Contents 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 17 Prepare the Installation oiiire eaaa ks eset eee need ad 17 High level process flOW 0 ccccccccceecceeeseeteeceeececeseeeeeeeesencaeeseeecaeesenaeeeeeeeeeaeenee 17 Section 1 Perform Windows 20000 Installation 0 0 c cceeceeeeeeteeteeeees 17 PHASE 1 Windows 2000 Installation cccceccecceceeeeeeeeeeeeeeeeeeeeteees 18 PHASE 2 Perform Hardware Status Check ccceceeeeeeeseeeeeeeeeteees 20 PHASE 3 Initialize Hard Disk Drive 0 c cccccceceececeeeeeeeeeeeeceeeeeeeeeeteees 21 PHASE 4 Adding Terminal Server Services 0 c ceeeeseeeeeeeeeeeeeeneeeeeeaee 22 Section 2 Configure the Network ccccceceeeneeeeeeeeeeeeeeeeeeeseeaeeeseeeeeeseeaaees 23 PHASE 1 Configure Server IP Address ccccecccceeeeeteeeeeenteeeeeeeneeeeeeee 23 PHASE 2 Attach Clients to Network and Test Network Link 24 PHASE 3 Domain Controller Setup ccccceesececceeeeeeee
10. Windows NT Server Setup screen to gather information about your computer 3 You can now proceed through the customization of your installation using the graphical interface NOTE You can later promote your Backup domain controller to Primary domain controller and vice versa Stand Alone Server cannot be promoted to Primary Domain Controller or demoted to Backup Domain Controller 4 Emergency repair disk HP recommends you create this disk because it saves your Windows NT Server Setup configuration Prepare a blank formatted floppy diskette to create this disk then click Next You do not need to insert the blank floppy diskette at this time as Windows NT Setup will actually perform the disk creation at the end of you configuration phase PHASE 4 Configure the Network 1 Click Next at the Windows NT Setup screen to install Windows NT Networking Click Next at the following window to use the network adapter embedded with your HP Server tc2100 Click Next to accept installing the Microsoft Internet Information Server When you reach the Network Adapters screen do NOT select Start Search Instead click the Select from list button to load the HP LAN driver a Select the Have Disk button when given a list of Network Adapter drivers to use HP specific driver b Insert the HP Server tc2100 Windows NT LAN driver HP disk NT 2 then press Enter c Press Enter to validate the selection of the Intel PRO Adapter
11. driver list until the next system boot Troubleshooting This section will help you resolve some of the most common installation problems Tip 1 Troubleshooting SCSI Host Bus Adapter Configuration The boot manager for Windows NT contains recovery logic to allow you to return to the last known good configuration If you have changed your SCSI host bus 13 Chapter 2 Installing Microsoft Windows NT 4 0 Server adapter configuration and Windows NT no longer boots follow these steps to recover 1 Undo any hardware changes you have made to the computer since it was last operational Reboot the computer Press the spacebar when the message Press spacebar NOW to invoke the Last Known Good menu Appears Follow the instructions on the screen to continue booting NOTE Do not log in if you pass the Press spacebar NOW to invoke the Last Known Good screen option because this will wipe out the configuration you want Once your computer is operational again double check all the hardware and software configuration changes you wish to make Look specifically for conflicts with parts of the existing system configuration that are not being changed If you cannot determine the source of the error contact the host adapter vendor or HP Technical Support for assistance Tip 2 NT Warning About Drives with More than 1024 Cylinders If the boot drive is new or just initialized Windows NT may give a warning message about disk drives h
12. for the CD to be automatically mounted as a volume Note the volume name example NW51SP1 type nwconfig NetWare Configuration Tool will open Scroll down to select Product Options 39 Chapter 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 8 Scroll up to select Install a Product Not Listed 9 Press F3 and specify the path including the volume name for example NW51SPx where x version of support pack 10 Press F10 to accept the default installation options NOTE If you want to be able to uninstall the Support Pack later you must select the option to back up files 11 Read NetWare warnings recommends avoiding installation during peak hours and follow on screen instructions 12 The system will automatically restart the GUI upon completion of the Support Pack installation Troubleshooting Tip 1 Restarting NetWare Installation If you want to restart NetWare installation from the very beginning use a utility such as fdisk to erase all data and partitions from your hard drive Then resume all installation process On Line Information and Software Sources e HP World Wide Web access http www hp com e Novell World Wide Web access http www novell com e Novell Networking BBS 801 429 3308 9 600 baud 40 5 Installing Red Hat Linux 7 1 Prepare the Installation Please refer to the Chapter 1 Preparing your HP Server tc2100 for your NOS installation for our rec
13. o Ifyou have access to a PC connected to internet and equipped with a CD RW drive you may download the latest Service Pack from Microsoft website at http www microsoft com ntserver nts downloads recommended then copy the Service Pack on a CD ROM It allows you to install the Service Pack from the CD ROM drive of your HP server o You may contact Microsoft Support at 800 936 5900 or 800 426 9400 to have a Service Pack CD ROM shipped to you 2 To install the Service Pack login on your HP server as the Administrator then run the Service Pack 3 Select Accept the License Agreement then click Install 4 When prompted click Restart to reboot your system remember to remove all diskettes and CD ROM from their respective drives NOTE When installing the service pack answer No if prompted to overwrite drivers files to keep the HP drivers you have previously installed Chapter 2 Installing Microsoft Windows NT 4 0 Server PHASE 7 Install HP Video Driver The Microsoft Windows installation process has installed the standard VGA video driver If you would like to make use of the high resolution video driver follow these steps 1 Ensure Microsoft Windows NT Service Pack version 6a or above is installed This is a REQUIREMENT 2 Logon as the Administrator on your HP server then insert HP Startup CD in the CD ROM drive The Startup CD will automatically start and a menu will display NOTE Your HP server should au
14. recommends to keep the default value by selecting Continue 5 Wait as the system performs the installation according to your settings Chapter 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 PHASE 3 Configure the Network 1 The installation proceeds under a graphical interface Follow the on screen instructions to configure your network server name IP adress Host name and domain etc NOTE Some settings can be defined by using the tree icon at the right 4 side of the field The network settings need to be customized to your environment Please refer to Novell NetWare manuals should you need further details on the networking setup fields Insert and browse the NetWare 5 1 licensing cryptographic diskette when prompted When prompted click Yes to reboot your system remember to remove all diskettes and CD ROM from their respective drives The system will load NetWare GUI Graphic User Interface PHASE 4 Install the Support Pack 1 You can get a copy of NetWare Consolidated Support Pack CSP from NetWare Website at http www support novell com csp You can either subscribe to the Novell Support Connection CD program or download CSP files individually You will need to mount the Novell Consolidated Support Pack as a NetWare volume Insert the NetWare Support Pack CD ROM Close the GUI At the system console prompt enter the command cdrom Wait for about 15 seconds
15. signature file Windows 2000 displaysa Digital Signature not Found box e To expedite release of new products drivers may be shipped by HP without signature files All Windows 2000 drivers provided by Hewlett Packard are submitted to Microsoft for certification testing Upon completion of testing Microsoft produces signature files HP then posts the revised driver package at http Awww hp com 30 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Chapter 3 If a signature warning is displayed during installation of a driver you may override the warning We recommend that you check the HP Website for the latest driver package If available install the new driver You can elect to have Windows 2000 ignore signatures Open Start Settings Control Panel System Hardware Driver Signing This is helpful if you are setting up multiple systems Digital signatures are a powerful way to ensure system integrity as you add drivers to your systems whether provided by HP or others Tip 6 Windows 2000 Recovery Options In the event that the current installation of Windows 2000 fails to boot this might happen after installing a new driver component software etc Windows 2000 provides the following recovery options to help you gain access to your Windows 2000 installation to replace damaged files and services for troubleshooting purpose HP therefore recommends that you install the Recovery Console see opt
16. system will start configuring the active directory display It will take a few minutes to complete If prompted insert Windows 2000 CD ROM and click OK to continue Configuring active directory display shows again Click Finish to close the Wizard utility This completes the active directory installation Click Restart Now to reboot the system Remove CD ROM if present At the login prompt type in the password Click the Options button and verify that the Log on to HOST appears on the dialog box Click OK to start the logon process Section 3 Completing the Installation PHASE 1 nstall the Service Pack 26 1 How to get a copy of Windows 2000 Service Packs o Ifyour HP server is already connected to internet you can download the latest Service Pack from Microsoft website at http www microsoft com windows2000 downloads o Ifyou have access to a PC connected to internet and equipped with a CD RW drive you may download the latest Service Pack from Microsoft website at http www microsoft com ntserver nts downloads then copy the Service Pack on a CD ROM It allows you to install the Service Pack from the CD ROM drive of your HP server o You may contact Microsoft Support at 800 936 5900 or 800 426 9400 to have a Service Pack CD ROM shipped to you To install the Service Pack logon on your HP server as the Administrator then run the Service Pack on your system If prompted press OK to accept Microsof
17. then Insert again to add an unlisted driver f Press F3 and specify the path A SCSTI then press Enter g The installation program takes a few seconds then automatically add the HP driver on the driver list NOTE The new HP driver may show the same device name description but is a more recent version h Scroll down and select Return to driver summary i Scroll down and select Continue 3 The next driver summary screen displays storage and network devices You need to replace the default Network board LAN driver by the HP LAN driver that performs faster and is more robust a Scroll down to chose Modify and press Enter b Scroll down to highlight the Network boards CE100B item and press Enter c The installation program displays the default LAN driver CE100B LAN Intel Pro 100 Management Adapter Press Delete to remove this driver d Insert HP disk NW 1 created with the Startup CD in the floppy drive e Press Insert to add a driver then Insert again to add an unlisted driver f Press F3 and specify the path A LAN then press Enter g The installation program takes a few seconds then automatically add the HP driver on the driver list NOTE The new HP driver shows the same driver name and device name description but is a more recent version h Scroll down and select Return to driver summary i Scroll down and select Continue 4 The installation program displays the partitioning properties HP
18. 00 2 Open a command prompt and type D I386 WINNT32 CMDCONS Where D is the CD ROM drive letter 3 Follow the screen instructions to complete the RC installation Booting RC 1 Shutdown and Restart system 2 Select Windows 2000 Recovery Console from the boot menu 3 The system will display a menu asking to select the instance of the NOS you want to boot For example it displays 1 C WINNT 4 Type 1 then Enter 5 Type the administrator password when prompted 6 At the command prompt type help and proceed to achieve your objective 7 Type exit when done troubleshooting NOTE The file access security can prevent you from getting to certain files Tip 7 Restarting Windows 2000 installation If you want to restart Windows 2000 installation from the very beginning use a utility such as fdisk to erase all data and partitions from your hard drive Then resume all installation process On Line Information and Software Sources HP World Wide Web access http www hp com Microsoft World Wide Web access http www microsoft com Microsoft Product Support Services http support microsoft com directory Windows NT Automated Database Advanced Systems at 800 936 4400 Microsoft Software BBS 206 936 6735 14 400 bps 33 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 Prepare the Installation Please refer to the Chapter 1 Preparing your HP Server tc2100 for your NOS installation for our
19. HP Server tc2100 Network Operating System Installation Guide For Microsoft Windows NT 4 0 Server Microsoft Windows 2000 Server and Microsoft Small Business Server 2000 Novell NetWare 5 1 and Novell Small Business Suite 5 1 Red Hat Linux 7 1 TurboLinux Server 6 5 Q invent HP Part Number P4648 90002 Printed August 2001 Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Acrobat is a registered trademark of Adobe Systems Incorporated ATI is a registered trademark of ATI Technologies Incorporated Intel is a registered trademark of Intel Corporation Microsoft and MS DOS are U S registered trademarks of Microsoft Corporation Windows an
20. Sources 16 HP World Wide Web access http www hp com Microsoft World Wide Web access http www microsoft com Microsoft Product Support Services http support microsoft com directory Windows NT Automated Database Advanced Systems at 800 936 4400 Microsoft Software BBS 206 936 6735 14 400 bps 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Prepare the Installation Please refer to the Chapter 1 Preparing your HP Server tc2100 for your NOS installation for our recommendations on the server preparation Then gather the following material e HP Server tc2100 Startup CD e Microsoft Windows 2000 CD ROM as well as the latest Microsoft Windows 2000 Service Pack 2 or above e Six blank formatted 3 5 inch diskettes e Two or more clients for testing purpose Optional High level process flow 1 Perform Windows 2000 Server Installation 2 Add Windows Terminal Services optional 3 Configure the Network 4 Complete the Installation Microsoft Service Pack HP drivers Recovery Console Section 1 Perform Windows 20000 Installation NOTE Though you may install Windows 2000 from Setup diskettes or directly from Windows 2000 CD ROM we recommend you the second method because it is faster l For ease of reading we will refer to Windows 2000 Server and Small Business Server 2000 both as Windows 2000 in this chapter 17 Chapter 3 Installing Micro
21. again to confirm their creation c Read the information related to setting up a Internet Domain then press OK d Select appropriate ODBC drivers select at least the default SQL Server Drivers then press OK 3 Setthe Time zone Date and Time then select Close 4 You will be notified that a standard VGA video driver has been installed Do not attempt to install the HP high resolution video driver at this time because they would be overwritten by the service pack installation We will help you Chapter 2 Installing Microsoft Windows NT 4 0 Server perform this operation later Click OK to leave this window then OK again to close the Display Properties window 5 When prompted insert the blank formatted disk to create the Emergency Repair Disk then click OK 6 When prompted remove the Emergency Repair disk and the Windows NT Server CD ROM from their drives and reboot the system by pressing Enter 7 The Windows NT logon screen will show after the POST as the basic Windows NT installation is now complete NOTE Windows NT installation may take a while at this step if you selected NTFS and the system has to convert the boot partition from FAT to NTFS PHASE 6 Install the Service Pack 1 How to get a copy of Windows NT 4 0 Service Packs o Ifyour HP server is already connected to internet you can download the latest Service Pack from Microsoft website at http www microsoft com ntserver nts downloads recommended
22. as determined that your computer s startup hard disk is new screen 6 Press F8 to accept the licensing agreement 7 At the drives partitioning screen select the target drive If you want to use the entire drive to install Windows 2000 then press Enter Otherwise press C to create a drive a partition In this example we will create a 2GB partition Please note that Windows 2000 does not have the 2GB limitation present on NT 4 0 a Press C to create a partition Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 b At the Create partition size prompt type 2048 and press Enter c HP recommends that you create all the partitions needed for each hard drive present on your system Select unpartitioned space and press C again to create additional partitions 8 Select the target drive to be used to install Windows 2000 Press Enter 9 Select Format the partition using the NTFS file system and press Enter 10 The installer will format and copy files to the hard drive 11 Ifyou have selected to install the NetRAID 1M driver Windows setup will prompt for the driver diskette again 12 The system will reboot and launch Windows 2000 graphic interface Be sure to remove the driver diskette before the reboot 13 At the Installation Wizard first dialog box click Next to continue 14 The Installing Devices screen will be shown with a progress bar on the display This may take 10 to 15 minu
23. aving more than 1024 cylinders during the first reboot from the hard drive Windows NT may hang just after the SCSI BIOS or Disk Array BIOS banner This is a Windows NT limitation please see Microsoft TechNet article Q137474 for details 14 In some situations the Windows NT installation program may detect the hard drive geometry incorrectly and thus limit the initial drive partition size to 1024 MB or hang while rebooting To correct this problem perform the following solutions In the Windows NT installation program 1 S ONE As e ee is Partition the primary partition to 1024 MB Format the primary partition using FAT Press F3 to quit the installation program Restart the installation program At the drive partition screen delete the 1024 MB primary partition Partition the primary partition to any desired size up to the drive capacity Continue with the Windows NT installation program Chapter 2 Installing Microsoft Windows NT 4 0 Server Tip 3 Service Pack Files Replaced Without Feedback Some system configuration changes may ask you to install the original Windows NT drivers diskette This may cause some system files to be replaced with the old version It is recommended that you apply the service pack again if you make any changes Tip 4 Using the NT Event Log to Diagnose Network Adapter Problems If the Network Adapter driver fails to start or does not appear to be working correctly examine the Event
24. d Windows NT are trademarks of Microsoft Corporation Linux is a registered trademark of Linus Torvalds Novell and NetWare are registered trademarks of Novell Incorporated Red Hat is a registered trademark of Red Hat Software Incorporated Adaptec is a trademark of Adaptec Incorporated Hewlett Packard Company Network Server Division Technical Communications MS 45SLE 10955 Tantau Avenue Cupertino California 95014 USA Copyright 2001 Hewlett Packard Company Contents 1 Preparing your HP Server tc2100 for your NOS installation css 1 Section 1 Hardware Setu c ccccceceeeeeeeeeeceeeeeeeseceaeaaeeeeeeeeeseneeneeeeeeeeeneee 1 Preparing your Hard Disk Drives c escececceceeeeeeeeeeeeeeeeeeseeeenaeeeeeeeeteees 1 Section 2 Updating your Server BIOS 0 00 cceceeeeeeeeeeeeeeeneeeeeeenaeeeeeeneeeeneaes 1 Section 3 Run HP Diagtools oraria Ea T TAE TA 2 Section 4 Using the StartUp CD eee ee eeeee ee eeeeeeeeeeaeeeeeeaeeeeeenaneeeseaes 2 2 Installing Microsoft Windows NT 4 0 Servet cccccsssseeecsseneeeeesseeeeeeessneeeees 3 Prepare the Installation ccccccceceeeeeeeeeccceceeeeeeeeeeeaeeeceeeeesatecaceeeeeeeeeetenaees 3 High tevel Frocess FlOW ss dsitieiaavticn teh Miceli Mid tini Mi ie 3 Section 1 Create the Drivers Diskettes cccceccecceceeeeeeeeeecaeeeeeeeeeeeenaees 3 Section 2 Create Microsoft Windows NT Installation Diskettes 4 4 Section
25. drive configuration Dynamic and Basic You can select the appropriate type by right clicking on the disk drive icon Dynamic drives are used to create volumes which can contain more than one physical hard drive Basic drives are used to create primary or local partitioned drives 21 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 PHASE 4 Adding Terminal Server Services 1 Open Start Settings Control Panel Add Remove Programs Click Add Remove Windows Components 2 3 4 Scroll to and click Terminal Services checkbox then click Next Select the mode you want to use Remote administration mode or Application sever mode then click Next NOTE The following instructions are based on the Application Or OO SS os D 11 server mode Please note the licensing requirement listed on the screen for this mode Consult with your Microsoft representative for setting the licensing server Select the default permissions for application compatibility then click Next Click Next to accept support tools and administrator tools settings If prompted insert the Windows 2000 CD ROM Click Finish to close the Wizard Click Yes to restart the system Remove the CD ROM After the system reboots login to the system Open Start Settings Control Panel Administrative Tools Check that the following services are now available Terminal Services Client Creator Terminal Serv
26. e notified that default display resolutions are being used Click OK You can now configure your settings and test them PHASE 3 Install the HP LAN driver Windows 2000 installation automatically detects the HP NIC and installs the driver bundled with the Windows 2000 CD ROM The following procedure will help you upgrade the driver using the HP Startup CD 1 Insert the HP Startup CD in your new server If CD ROM auto start is enabled a menu will display You may close this menu 2 Open Start Settings Control Panel System Hardware Device Manager 3 Open the Network Adapters tree and double click on the appropriate adapter to display its menu 27 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 4 From the Adapter Properties dialog box click the Driver tab then Update Driver to open the Update Device Driver Wizard Click Next 5 Atthe prompt What do you want the wizard to do select Search for a suitable driver for my device and click Next 6 Unselect the Floppy disk drive checkbox to keep only the CD ROM and click Next 7 Wait for the system to find the appropriate driver net82557 inf then click Next 8 Click Finish once the driver has been loaded 9 Exit all open windows and restart your computer This is not required if you only have one NIC on your system Otherwise it is recommended to reboot to make sure other HP D5013B adapters get initialized pro
27. e up arrow key to view more driver selections b Select the IDE CD ROM ATAPI 1 2 PCI IDE Controller driver then press Enter c Replace the diskette when prompted and press Enter Ensure that both the PCI SCSI if applicable and CD ROM IDE controllers are properly detected by checking the status at the top of the screen The installation will not be successful if these two drivers are not properly installed If you have any more mass storage device drivers to install you may do so at this time by pressing S When completed press Enter to continue PHASE 2 Hard Drive Preparation 1 2 Press Enter to continue if you are warned about your hard disk containing more than 1024 cylinders Your HP system can indeed handle this correctly Press C when prompted to continue with the installation Chapter 2 Installing Microsoft Windows NT 4 0 Server NOTE Windows NT setup will prompt a different menu if you have reconfigured your new HP server to use a hard drive already containing data 3 Insert the Windows NT CD ROM when prompted then press Enter NOTE Your CD ROM drive needs few seconds to detect the newly inserted CD ROM You may need to press Enter again if you pressed Enter too quickly the first time 4 Press Page Down to read the Licensing Agreement then F8 to agree and proceed with the installation 5 The Windows NT Server Setup screen will display the system hardware and software components it detected Press E
28. eeeeneeeeeeeeeteees 25 Section 3 Completing the Installation cc eecceeeeeeeeeeeeeeeeeeeeeeseeeeeeeseeeaees 26 PHASE 1 Install the Service Pack c ccccceceeeeeeeeceeeeeeeseeeesaeeeeeeeetees 26 PHASE 2 Install the HP Video Driver ccseccceeeeeeeeeeteeeeeeeeteees 27 PHASE 3 Install the HP LAN drivel cccecccseeecceeeteeeeeeseteeeeeeeeeteees 27 PHASE 4 Install Windows 2000 Recovery Console ceeeeeeeeeees 28 TOUDISSOOTIN GO issiazsccviswhs cx es a ges aves Ses sav hei dean cenhl Ai 28 Tip 1 Upgrading from NT 4 0 to Windows 2000 28 Tip 2 Windows 2000 Installation halts about three minutes after starting to boot from CD ROM fia nah cen iehi atalino vie 28 Tip 3 Configure the Parallel LPT Port for ECP Mode 29 Tip 4 Installing HP NetRAID 1M Driver After Windows 2000 is Installed 30 Tip 5 Windows 2000 Drivers Signatures c cceeceeeeeeeeeeeeteeneeeeeeaees 30 Tip 6 Windows 2000 Recovery Options cccccceeeseeceeeeeeeeeesenteeeeees 31 Tip 7 Restarting Windows 2000 installation eeccceeseeeeeeeeeeeeeneees 33 On Line Information and Software Sources cecceceeeeeeeeeeeeeeeeeeeeeeenaees 33 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 35 Prepare the Installation ccccccceeeeeeceeceeeeeeeeeenneaeceeeeesecencaeeeeeeeeesecsecneeeeees 35 High level process OW csesiissrins
29. eeeesstnaeeneees 41 PHASE 2 Configure the Server c cccccccceeeseeeeeeetneeeeestneeeeetneeeeetneeeeee 41 PHASE 3 Complete the Installation c ccccceceeeeeseceeceeeeeeeseestneeeeees 42 On Line Information and Software Sources ceseeeecceeeeeeeeeeeeteeeeeeeeeeeees 43 Installing TUrbOLINUX Server 6 5 ccececeseeeeeeeeeeeeeeeeseeeseeeesneesesesneeeneeeeneens 45 Prepare the Installati n Siin a e a a e at 45 High level process flOW cccccceceseeceeeeseeeeeeseeeeeeeseeeeeeeseeeaeeeseeeaeeeseenaeeeseeaaees 45 Perform TurboLinux Installation ccccccccceceeeeeeeeeeeeeeeeeeeesecneaeeeeeeeeeteenaees 45 PHASE 1 Launch the Installation ceccceecceceeeeeeeeecaeceeeeeeesessncaeeeeees 45 PHASE 2 Configure the Server c ccceccececseeeeeeeetteeeetiieeeeetieeeeesneeeeee 45 PHASE 3 Complete the Installation c ccccceeeeeeeeceeeeeeeeeeeeeenneeeeeees 46 On Line Information and Software Sources ceseeeecceceeeeeeeeeeeteeeeeeeeeeees 46 1 Preparing your HP Server tc2100 for your NOS installation Section 1 Hardware Setup Prepare your HP server following the instructions in the HP Server tc2100 Installation Guide It is recommended that you do not install any third party adapter until you verify that the HP equipment is functioning properly and you complete the NOS installation Preparing your Hard Disk Drives The HP Tower Serv
30. een to continue the installation 4 Insert your NetWare Small Business Suite 5 1 License diskette and press Enter The system will proceed with Novell installation Press F10 to accept the License Agreement For both NetWare 5 1 and Small Business Suite 5 5 1 5 Press Enter to setup a new server then scroll down and choose Continue 6 Modify or accept the server settings the regional settings as well as the mouse and video configuration PHASE 2 Install HP Drivers 1 The installation program then detect your hardware and attempt to match the drivers to the hardware It displays a driver summary screen 2 Ifyou have an IDE system press Enter to continue If you have a SCSI model you need to install the HP SCSI driver the SCSI driver proposed by default by NetWare does not install properly a Scroll down to chose Modify and press Enter b Scroll down to highlight the Storage Adapters item and press Enter c The installation program displays the drivers detected a SCSI driver and a generic ATA IDE ATAPI Adapter driver IDEATA HAM Press Delete to remove the default SCSI driver The only remaining driver should be the IDEATA HAM driver NOTE Do NOT remove the IDEATA driver because it is used by the CD ROM Drive d Insert HP disk NW 1 created with the Startup CD in the floppy drive 37 Chapter 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 38 e Press Insert to add a driver
31. elect Add As HP provides a specific driver click Have Disk when given a list of Network Adapter drivers Insert the HP LAN driver diskette provided with the accessory card then press Enter Note that you may have to browse the diskette to locate the driver Select the HP 10 100TX PCI LAN Adapter then click OK Chapter 2 Installing Microsoft Windows NT 4 0 Server NOTE The installation of the new network adapter will not take effect until you restart the server If you want to implement Adapter Teaming requires 2 Network Adapters Windows NT 4 0 Service Pack version 6a or above is required If there are errors during the installation you should verify you installed the correct driver for your adapter HP NetRAID 1M Adapter 1 Create the HP NetRAID driver for Windows NT diskette using the Navigator CD provided with your NetRAID card You may refer to the NetRAID card manuals or HP Navigator CD for additional details 2 Open Control Panel SCSI Adapters Drivers tab 3 Select Add 4 Click Have Disk when given a list of SCSI Adapters drivers then browse the A drive to locate the appropriate NetRAID 1M driver in directory A NETRAID Click OK to install it 5 Select the Hewlett Packard NetRAID 1M Adapter and click OK 6 In the System Settings Change windows click Yes to restart Windows NT NOTE If you do not restart the system at this point the HP NetRAID 1M Adapter driver will not be present in the
32. ems at HP When you have a set of drives previously used with a DAC and move them to a SCSI adapter Using a disk imaging utility to duplicate a hard drive will create a duplicate signature At this time Microsoft has no fix for this problem For more information please refer to Microsoft document ID Q226361 HP recommends that you use the following workaround for this problem 1 If you experiences this problem remove all drives with the exception of the target boot drive Install Windows 2000 and then add the removed hard drives to the system Run the Disk Management tool to prepare the remainder of the drives to be used in the system a Boot the system with a Windows 98SE recovery diskette This version supports FAT32 which works on large hard drives b Perform an FDISK on each drive c Install Windows 2000 Tip 3 Configure the Parallel LPT Port for ECP Mode The device manager may not show this port on the list when not configured in ECP mode HP recommends that you systematically configure the LPT port for ECP mode Use the following procedure to change the setting l 2 3 Press F2 during power on self test Select Advanced I O Device Configuration Parallel Port Mode Press Enter and select ECP Press F10 and select yes to confirm to save and exit 29 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Tip 4 Installing HP NetRAID 1M Driver Afte
33. enerate activities to stress the system The following steps use standard tools provided with the Windows NT Server installation 1 Inspect the error log in the event viewer Start Programs Administrative Tools Event Viewer to verify that no errors were detected If any errors are found please refer to the troubleshooting section of this document and Windows NT Reference Manual for help NOTE Windows NT Event Viewer may have recorded network errors if your HP server was not connected prior to your login If you can not resolve the problem please contact your HP service representative or use HP website for additional troubleshooting resources Run the Windows NT Diagnostic Tool Start Programs Administrative Tools Windows NT Diagnostic to gather information about system BIOS resources physical memory and video Check that your different adapters are correctly installed a Open the control panel Start Settings Control Panel b Check the status of the Network adapter by selecting Intel PROSet II You may perform the diagnostics by selecting the Diagnostics tab then click on Run Tests Upon completion close the Intel PROSet II window if you performed the diagnostics Windows will recommend that you reboot the system c Check the status of your SCSI adapter by selecting SCSI Adapters in the Control Panel and click Properties for each device Section 6 Attach Clients to Network and Test Network Link
34. er tc2100 comes with new hard disk drive s that do not need specific setup If you install additional and USED hard disk drives in your new server e Note that most NOS installations remove all data from the hard disk they are installed on If you wish to use your additional hard disk drives to access existing data in you new server HP recommends that you install and configure this these hard disk drive s AFTER completing the NOS installation e Ifyou wish to recycle used hard disk drives a Perform a media check b Use a utility such as fdisk to erase all data and partitions from your hard drive Section 2 Updating your Server BIOS HP recommends that you update your server BIOS with the latest system BIOS version to enjoy the most recent compatibility fixes Insert the HP Startup CD in a Windows PC and follow the on screen instructions NOTE If the Windows PC does not auto start the Startup menu start it by opening Startup htm found at the root level of the Startup CD Chapter 1 Preparing your HP Server tc2100 for your NOS installation Section 3 Run HP Diagtools To perform HP Diagtools hardware diagnostic on your HP Server tc2100 switch off your HP server then reboot on the Startup CD and follow the on screen instructions View and save the hardware inventory after the test Section 4 Using the Startup CD The Startup CD included with your HP Server tc2100 system may be used as follows Startup CD Usage
35. eric 104 key PC keyboard and a 2 Button Mouse e HP recommends using Automatic Partitioning Partition Disk section NOTE The network settings need to be customized to your environment Please refer to TurboLinux manuals should you need further details on the networking settings e HP recommends selecting Everything for the Installation Type because this is the only mode that includes the X Window graphical interface e Should you select Everything for the Installation Type you will be prompted for your monitors and video hardware references o Youcan find HP monitors references on the back of your monitor o HP Server tc2100 comes with a ATI Mach64 video chip which is automatically detected by TurboLinux e HP recommends selecting login type as Graphical Configure X section PHASE 3 Complete the Installation 1 Upon completion of the customization the installation program asks for confirmation before proceeding with the install Click Yes Next to proceed 2 You may install additional packages once the above installation is completed Additional packages require specific TurboLinux CD ROMs 3 HP recommends that you create a boot diskette that will allow you to boot and manage your server when experiencing problems in loading your TurboLinux environment 4 Click Finish to exit the installation program 5 At the prompt press Enter to reboot your system and login to your new TurboLinux environment Remo
36. gured to use DHCP If no DHCP server is found on the network the system will auto configure a random IP address to start functioning It is important that you configure the proper IP address to be able to communicate with the clients 1 Right click My Network Places Properties Local Area Connection on your HP server NOTE If you HP server host several Network adapters the window will show one Local Area Connection icon for each Network adapter present in the system Identify the proper adapter by browsing each one 2 Click Internet Protocol TCP IP Properties Use the following IP address 3 Enter appropriate IP address 23 Chapter 3 4 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Click the OK to continue then OK again to exit the Local Area Connection Properties window Click Yes to restart your computer and take this settings into account PHASE 2 Attach Clients to Network and Test Network Link 1 Create shares create a folder on your HP server hard drive then share it right click Sharing Create users using Windows 2000 Computer Management utility Start Programs Administrative Tools Computer Management System tools Local Users and Groups Users Connect clients PC to the network your HP server operates on Open a command prompt window to verify the TCP IP configuration and enter the command ipconfig all To verify the server and clients can communicate properly
37. he Event viewer to make sure that there are no errors in the log Click on Start Programs Administrative tools Event viewer Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 NOTE Windows 2000 Event Viewer may have recorded network errors because your network is not configured yet Please discard these errors 6 Exit event viewer PHASE 3 Initialize Hard Disk Drive To manage your different drives and partitions l a 3 Click Start Programs Administrative Tools Disk Administrator Click OK to proceed when notified you have a new hard disk to configure Select available hard disk space on the graphic and use menus to create additional partitions Exit the Disk Administrator To complete formatting of new partitions open My Computer then right click on the new unformatted partition s and select format To start the disk administrator use the following procedure 1 Click Start Programs Administrative Tools Computer Management 2 Double click Storage Disk Management in the tree 3 The Write signature and Upgrade wizard will start if you have new hard drives with no signatures on them Follow the on screen instructions to create this signature 4 Select available hard disk space on the graphic and use menus to create additional partitions 5 Format all partitions that are not formatted yet 6 Exit the Computer Management tool NOTE There are two types of hard
38. ices Configuration and Terminal Services Manager Create Client Installation Diskettes 22 l 2 3 Double click Terminal Services Client Creator Select the appropriate client type for your environment Click Format disk if needed Check the number of disks required and label them as Terminal Services for Disk x y Click OK to proceed Follow on screen instructions to perform the diskettes copies Click OK at the screen that reads y floppies were created Click Cancel to end the Create Installation disks utility Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Install the Client Utility on a Client Workstation 1 Insert diskette 1 in the target client and run A setup exe Click Continue at the setup screen Complete the Name and Organization Information form You will be prompted for this information only the first time the diskettes are used Click OK to validate then OK again to confirm Click I Agree to accept the license agreement Click the Large Icon to start installation Select the installation mode you feel appropriate all users Yes or current user only No Insert following diskette s when prompted and follow screen instructions Click OK when the installation is completed then shutdown and restart workstation Section 2 Configure the network PHASE 1 Configure Server IP Address During the installation process the system was confi
39. ion 3 below to enhance the system configuration Recovery option 1 Last known good configuration Activated by pressing F8 during the system process of Windows 2000 and selecting Last Known Good Configuration from the menu This boot mode is used in the case that the system fails to boot after installing a new software or driver The system will use the previous registry setting to initialize and boot the system Recovery option 2 Safe Mode Boot Activated by pressing F8 during the system boot It provides minimal configuration with required drivers and services The safe mode boot provides three options l 2 3 Standard safe mode boot Provides no network services or drivers Networking disabled Includes networks services and drivers Directory services restore mode Brings system up with directory services disabled with the intent of recovering active directory Safe mode boot is guided by the registry key hklm CurrentControlSet Control SafeBoot with the use of the Minimal and Network subkeys The IOManager and Service Control Manager look at the registry to load the driver and services Such approach avoids loading a problematic driver or service 31 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 4 Command prompt Provides an alternate command shell CMD EXE instead of the explorer This is dictated by the registry key hk1lm system CurrentControlSet Control SafeBoot AlternateShe
40. ll There is a Safe Mode boot loophole Since NTLDR loads Boot Load drivers these drivers bypass the IO Manager s Safe Mode check Recovery option 3 Recovery Console RC Boot The Recovery Console RC can be used when safe boot fails You can enter RC e either by booting from Windows 2000 CD ROM e or by installing the RC boot on your system It is recommended to install the RC immediately after installing Windows 2000 Start RC Booting from Windows 2000 CD ROM If you have a need of booting the Windows 2000 recovery console but this feature is not installed on the system use the following procedure to boot the RC from the Windows 2000 CD ROM 1 Insert the Windows 2000 CD ROM and start the reboot sequence 2 Press any key when prompted to start booting from the Windows 2000 CD ROM 3 Press F10 at the Welcome to Setup screen NOTE This is an undocumented option The bottom of the display is asking you to press Enter R or F3 4 The system will display a menu asking to select the instance of the NOS you want to boot For example 1 C WINNT 5 Type 1 then Enter 6 Type the administrator password when prompted 7 At the command prompt type help and proceed to achieve your objective 8 Type exit when done troubleshooting Installing RC 1 Insert Windows 2000 CD ROM If CD ROM auto start is enabled click exit to close the applet 32 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 20
41. low l 2 3 4 5 6 Create the drivers diskettes using HP Startup CD Create Microsoft Windows NT installation diskettes Perform Windows NT installation Initialize Hard Disk Drives Perform Hardware status check with Windows NT Diagnostic Tool Attach clients to network and test network link Section 1 Create the Drivers Diskettes l 2 Locate two blank formatted 3 5 diskettes Insert your HP Startup CD in a Windows PC and follow the on screen instructions to create the following diskettes o HP Server tc2100 Windows NT SCSI driver HP disk NT 1 o HP Server tc2100 Windows NT LAN driver HP disk NT 2 Chapter 2 Installing Microsoft Windows NT 4 0 Server NOTE If the Windows PC does not auto start the Startup menu start it by opening Startup htm found at the root level of the Startup CD Section 2 Create Microsoft Windows NT Installation Diskettes Three installation diskettes are required to install Microsoft Windows NT 4 0 on your server Follow these steps to create these installation diskettes 1 Locate three blank formatted 3 5 diskettes 2 Insert your Microsoft Windows NT 4 0 CD ROM into a desktop PC 3 From a DOS prompt type C D i386 winnt32 ox where D is the drive letter for the CD ROM 4 Follow the prompt and insert the diskettes in the order described Section 3 Perform Windows NT Installation The installation of Windows NT contains several phases e Phase
42. nter if the configuration matches your computer 6 The setup then shows a list of hard drives on your server along with the partitions proposed on each drive The default partition on which to install Windows NT on the first drive Drive 0 is highlighted Select C to create a partition in the unpartitioned space 7 Enter the appropriate size for your NOS partition HP recommends 2000MB Press Enter to validate the partition size 8 Press Enter to Install Windows NT on the New Unformatted partition 9 Select a file system format FAT DOS type file system or NTFS Windows type file system for this NOS partition HP recommends using NTFS Then press Enter to proceed with formatting the partition this operation may take time depending on your partition size 10 Specify the directory for Windows NT default WINNT then press Enter 11 Press Enter to have Setup examine your hard disks 12 Insert the HP Server tc2100 Windows NT SCSI driver HP disk NT 1 when prompted for a disk then press Enter 13 Remove the above disk and Windows NT CD ROM from their drives before pressing Enter to restart your computer PHASE 3 System Configuration Details 1 Insert Windows NT Server CD ROM when prompted then press Enter Chapter 2 Installing Microsoft Windows NT 4 0 Server NOTE Your CD ROM drive needs few seconds to detect the newly inserted CD ROM If the window Files Needed appears press Enter again 2 Click Next at the
43. ommendations on the server preparation Then gather the following material e HP Server tc2100 Startup CD e Red Hat Linux 7 1 CD ROMs 1 and 2 e Two or more clients for testing purpose Optional High level process flow 1 Perform Linux 7 1 installation 2 Attach clients to network and test network link Perform Red Hat Linux Installation PHASE 1 Launch the Installation 1 Turn on the server and insert the Red Hat Linux 7 1 bootable CD ROM 2 The system will display a text menu Press Enter to start installation using the graphical interface PHASE 2 Configure the Server The installation program now displays a graphical interface You can proceed through the customization of your installation Please note the following recommendations e Your HP server comes with a Generic 104 key PC keyboard and a 2 Button Mouse PS 2 NOTE If you wish to change your keyboard type after you have booted your Red Hat Linux system you may use the usr sbin kbdconfig command 41 Chapter 5 Installing Red Hat Linux 7 1 HP recommends selecting a Custom System installation type because this mode includes the X Window graphical interface Install Options section HP recommends using the default partitioning mode Automatically partition and REMOVE DATA Disk Partitioning section NOTE The network settings need to be customized to your environment Please refer to Red Hat manuals should you need further details
44. on the networking settings At the Selecting Package Groups Section HP recommends selecting the X Window graphical interface package NOTE Remember to select an appropriate package group that matches your network settings example the DNS Name Server package may be required if you have set up your new server to be the DNS controller Should you select to install a graphical interface you will be prompted for your video hardware and monitor references X Configuration section o Red Hat will detect your chip as a ATI Mach 64 chip but you should correct manually the selection as your HP Server tc2100 comes with a ATI Rage XL AGP video chip o You can find HP monitors references on the back of your monitor o HP recommends selecting login type as Graphical Custom Configuration section PHASE 3 Complete the Installation 42 1 Upon completion of the customization the installation program asks for confirmation before proceeding with the install Click Next to proceed The installation may prompt for Red Hat Linux CD ROM 2 depending on the packages you choose to install HP recommends that you create a boot diskette that will allow you to boot and manage your server when experiencing problems in loading your Red Hat environment Click Exit to exit the installation program Remove the CD from the drive The system reboots and loads your new Red Hat environment Chapter 5 Installing Red Hat Linux 7
45. ou may open the Windows 2000 Configure Your Server wizard at any point of time by clicking Start Programs Administrative Tools Configure Your Server PHASE 2 Perform Hardware Status Check In this section you will run Windows 2000 Device Manager tool to identify any issues with the installed devices or resource conflicts 20 l Open Start Settings Control Panel System Hardware Device Manager Verify that no devices have either a yellow band or question mark symbol next to it o Yellow means that there is a resource issue with the device o Question means that the device is unknown If or symbols are reported then double click on each of the devices with or Use the Device Status message for troubleshooting Or if a printer is available use the View Print from the menu to get a report Verify if the installed drivers are digitally signed a In the Device Manager select the device e g HP NetRAID 1M that you want to verify b Right click Properties Driver c Locate the Digital Signer If the driver of that device is digitally signed then it will display MS Windows 2000 Publisher or Microsoft Windows Hardware Compatibility Publisher If the driver of the device is not digitally signed we recommend that you check the HP Website www hp com to install the latest driver package Exit the Device manager System Properties and Control Panel applications Check t
46. perly 10 After restarting Windows connect to your network and test for connectivity PHASE 4 Install Windows 2000 Recovery Console Please refer to Tip 6 in the Troubleshooting section Troubleshooting This section will help you resolve some of the most common installation problems Tip 1 Upgrading from NT 4 0 to Windows 2000 It is possible to upgrade from any edition of NT 4 0 including Terminal Server to Windows 2000 Please refer to the readme doc on the Windows 2000 CD and the Windows 2000 Setup Guide for information on how to perform the upgrades Tip 2 Windows 2000 Installation halts about three minutes after starting to boot from CD ROM When installing Windows 2000 on any X86 system with more than one hard drive it is possible to experience the following error Setup has encountered an error and cannot continue Contact technical support for assistance The following status codes will assist them in diagnosing the problem 0x4 0x1 0x0 0x0 28 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 The cause of this problem is that the NTLOADER is encountering a duplicate hard drive signature This signature is calculated by the NTLOADER code after reading a specific sector offset from the hard drive The following list provides some of the things that can cause hard drive to have duplicate signatures 1 Low level formatting the drives We reproduced this on several syst
47. r Windows 2000 is Installed 1 Use the HP Navigator CD ROM shipped with your HP NetRAID 1M accessory to create the Windows 2000 driver diskette a Boot your server or any PC system with the Netserver Navigator in the CD ROM b Go to the Diskette Library from the main menu and follow on screen instructions NOTE Please consult the HP NetRAID 1m installation guide for instructions on doing the physical installation of the adapter 2 Ensure that the HP NetRAID 1M controller is installed in your system then reboot your system so that the system can recognize the controller 3 When the system is rebooted and the controller recognized Windows 2000 automatically launches the Found New Hardware wizard and displays a Files Needed dialog box 4 It prompts for the location on the A drive for the HP NetRAID 1M controller driver files Insert the driver s diskette created with the HP Navigator CD ROM and click OK The system will proceed with the installation of the driver 5 When the driver finishes installing click Finish to exit the Found New Hardware wizard 6 Atthe message Do you want to restart the computer now click Yes to reboot the system remember to remove all diskettes and CD ROM from their respective drives Tip 5 Windows 2000 Drivers Signatures Windows 2000 checks for digital signatures on driver files to help maintain system integrity During the installation or update of a driver if there is no matching
48. r idni randsi rarat idiaa dei randi aneda adda idane a 35 Section 1 Run HP Diagtools Optional ccccceeeeeeeeeeeeeeeeeeeeeeeeneeeeeenaeees 35 Section 2 Create the Drivers Diskettes cececcecceceeeeeeeeeteeeeeeeeeeeteenaees 35 Section 3 Perform NetWare 5 1 or Novell Small Business Suite 5 1 Installation36 PHASE 1 Start the Installation ccceccececeeeeeeeeneeceeeeeeeseeeeneeeeeeeeeteees 36 PHASE 2 Install HP Drivers cccecccseccececeeeeeeeeeeceeeeeeeseeecceeeeeeeetees 37 PHASE 3 Configure the Network 00 cccccscsececeesteeeeeenneeeeeeneeeeeenaeeeeeeaas 39 Contents PHASE 4 Install the Support Pack 000 022 cceececeeceeeeeeeeeeeecaeeeeeeeeeseennaeeneees 39 TrOUBIOSMOOTIN Gxt niriana aee E tice vadsdecuaadnecestaadigend ide iecinsdbicentiads 40 Tip 1 Restarting NetWare Installation cc cceeceeeeeeeeeeeeneeeeeeeneeeeeeaas 40 On Line Information and Software Sources ceseceeeceeeeeeeeeeeeeteeeeeeeettees 40 Installing Red Hat Linux 7 1 0 0 cceccccesseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeneeseeesseenseesenenens 41 Prepare the Installation c ccccceceeeeeeeeneeceeeeeeeteceneaeeeeeeeseseceneaeeeeeeeeenennaees 41 High level process IOW eresia darii eaaa inaa aa EE T T 41 Perform Red Hat Linux Installation cccccccceeeececceeceeeeeeeseceecaeeeeeeeeeeesnaees 41 PHASE 1 Launch the Installation 0 0 eccceecceceeeeeeeeeceeeeeeee
49. recommendations on the server preparation Then gather the following material e HP Server tc2100 Startup CD e Novel NetWare 5 1 or Novell Small Business Suite 5 1 CD ROM and latest Support Pack CD ROM e NetWare 5 1 or Novell Small Business Suite 5 1 licensing cryptographic diskette e Two or more clients for testing purpose Optional High level process flow Run HP Diagtools optional diagnostics Perform Windows 2000 installation Initialize Hard Disk Drives 1 2 3 4 Perform Hardware status check with the Windows 2000 Diagnostic Tool 5 Attach clients to network and test network link 6 Install Windows Terminal Services optional Section 1 Run HP Diagtools optional To perform HP Diagtools hardware diagnostic on your HP Server tc2100 switch off your HP server then reboot on the Startup CD and follow the on screen instructions View and save the hardware inventory after the test Section 2 Create the Drivers Diskettes 1 Locate one blank formatted 3 5 diskette 35 Chapter 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 2 Insert your HP Startup CD in a Windows PC and follow the on screen instructions to create the HP Server tc2100 NetWare SCSI and LAN drivers HP disk NW NOTE If the Windows PC does not auto start the Startup menu start it by opening Startup htm found at the root level of the Startup CD Section 3 Perform NetWare 5 1 or Novell Small Business S
50. soft Windows 2000 Server and Small Business Server 2000 PHASE 1 Windows 2000 Installation 18 1 Boot your new server from the Windows 2000 CD ROM 2 You will see a message that reads Setup is inspecting your hardware configuration Then the setup screen will be displayed 3 The system will briefly show at the bottom of the display Press F6 if you need to install a third party SCSI or RAID controller If you have installed a HP NetRAID 1M Raid controller in your system you will need to install the corresponding HP driver because the Window 2000 CD ROM does not include appropriate driver Press F6 at this time The system will then allow you to manually specify you adapter a Press S to Specify Additional Device b When prompted to insert driver diskette please insert the HP NetRAID 1M driver for Windows 2000 diskette You create this diskette using the Navigator CD provided with your NetRAID card You may refer to the NetRAID card manuals or HP Navigator CD for additional details c Press Enter to continue d Select Hewlett Packard NetRAID 1M RAID CONTROLLER from the list provided on the display then press Enter NOTE Unfortunately Windows 2000 setup only gives you a very short time to press F6 If you missed it you should reboot your system and resume from step 1 above 4 Press Enter to continue at the Windows 2000 Server Setup Welcome to Setup Screen 5 Press C to continue Setup at the Setup h
51. t 2000 Publisher Certificate Select Accept the License Agreement then click Install When prompted click Restart to reboot your system remember to remove all diskettes and CD ROM from their respective drives Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 PHASE 2 Install the HP Video Driver The Microsoft Windows installation process has installed the standard VGA video driver If you would like to make use of the high resolution video driver follow these steps 1 Ensure Microsoft Windows 2000 Service Pack version 2 or above is installed This is a REQUIREMENT 2 Logon as the Administrator on your HP Server tc2100 then insert HP Startup CD in the CD ROM drive The Startup CD will automatically start and a menu will display NOTE Your HP server should auto detect the presence of the Startup CD and start the Startup menu If your HP server does not auto start the Startup menu start it by opening Startup htm which can be found at the root level of the Startup CD 3 Select Automated installation of hp video driver for Microsoft Windows 2000 Server 4 The HP video driver ATI video setup program will open Click Next to start the installation then click Yes to accept the License Agreement 5 Click Finish when prompted to restart your system at the end of the installation remember to remove all diskettes and CD ROM from their respective drives 6 After your logon you will b
52. tes 15 You can now proceed through the customization of your installation using the graphical interface NOTE The network settings may need to be customized to your environment Please refer to Microsoft 2000 manuals should you need further details on the networking settings 16 The Installing Components Display screen starts with a progress bar It takes about 20 minutes to complete this section 17 The wizard will then automatically start the Performing Final Tasks section to complete the installation This step may takes a long time too with the progress bar apparently not moving NOTE There may be a period of time with no apparent activity at the Saves Settings Be patient 18 At the Completing the Windows 2000 Setup Wizard screen remove the CD ROM then click Finish The system will automatically reboot from the hard drive 19 Follow screen instructions to logon press Ctrl Alt Del Enter the administrator password you have defined earlier 19 Chapter 3 Installing Microsoft Windows 2000 Server and Small Business Server 2000 20 Ifyou installed Windows 2000 Server Windows 2000 Configure Your 21 Server will launch Close this window as we will postpone the customization of your server until completion of all the installation steps If you installed Microsoft Small Business Server 2000 Click Cancel to close the Setup needs the location of the Small Business server 2000 Setup files window NOTE Y
53. to detect the presence of the Startup CD and start the Startup menu If your HP server does not auto start the Startup menu start it by opening Startup htm which can be found at the root level of the Startup CD 3 Select Automated installation of hp video driver for Microsoft Windows NT Server 4 The HP video driver ATI video setup program will open Click Next to start the installation then click Yes to accept the License Agreement 5 Click Finish when prompted to restart your system at the end of the installation 6 After your logon you will be notified that default display resolutions are being used Click OK You can now configure your settings and test them Section 4 Initialize Hard disk Drive To manage your different drives and partitions E 2 3 10 Click Start Programs Administrative Tools Disk Administrator Click OK to proceed when notified you have a new hard disk to configure Select available hard disk space on the graphic and use menus to create additional partitions Exit the Disk Administrator To complete formatting of new partitions open My Computer right click on a new partition s to be formatted and select format Chapter 2 Installing Microsoft Windows NT 4 0 Server Section 5 Perform Hardware Status Check This section will provide a simple way to verify your installation of Windows NT Note that Windows NT Resource Guide CD ROM available from Microsoft provide utilities to g
54. uite 5 1 Installation The installation of NetWare 5 1 or Novell Small Business Suite 5 1 contains several phases e Phase 1 Start the Installation e Phase 2 Install HP Drivers e Phase 2 Configure the Network PHASE 1 Start the Installation NOTE If your hard drive contains data or is not new HP recommends to use a utility such as fdisk to erase all data and partitions from your hard drive 1 Insert the Novell NetWare 5 1 or Novell Small Business Suite 5 1CD ROM and boot the system For NetWare 5 1 2 Press Enter to read the license agreement then press Esc and select Accept License Agreement 3 Press Enter to Create a New Boot Partition 4 HP recommends accepting the default 100MB boot partition by pressing Enter to continue 5 Ifyou accept erasing all data on your disk select Continue Your system will now create the partition reboot and format that partition 36 Chapter 4 Installing Novell NetWare 5 1 and Novell Small Business Suite 5 1 For Small Business Suite 5 1 1 A graphic interface will display Select your language then click Next 2 When prompted about the DOS Partition select Create a new DOS partition then click Next hp recommends you keep the default partition size Click Yes to any warnings Click Next at the summary screen to reboot and continue the installation 3 At the Install Type screen select Advanced Installation then click Next Click Next at the summary scr
55. ustomize the options proposed by Windows 2000 to match your environment 5 Click Next at the Domain Controller Type to accept the default Domain Controller for a new Domain 6 Click Next at the Create Tree or Child Domain to accept the default Create a new domain tree 7 Click Next at the Create or Join Forest to accept the default Create a new forest of domain trees 8 At the text box for Full DNS name for new domain type in the assigned DNS name for your server for example mycompany com 9 Click Next The system may take a few minutes before moving to next screen 10 Click Next at the NetBIOS Domain Name dialog box to accept default Domain NetBIOS name 11 Click Next to accept Database and Log Locations default directories 12 Click Next to accept default Shared System Volume 13 The system will display a dialog box that reads The Wizard can not contact the DNS Server Confirm your DNS configuration or install and configure a DNS server on this computer Click OK 14 Click Next to accept the installing DNS on your new server 25 Chapter 3 15 16 17 18 19 20 21 22 Installing Microsoft Windows 2000 Server and Small Business Server 2000 Click Next to accept the default permission value Permissions compatible with pre Windows2000 Server Enter and confirm the Administrator password and click Next Review the Summary display and click Next to continue The
56. ve the CD from the drive On Line Information and Software Sources e HP World Wide Web access http www hp com e TurboLinux World Wide Web access http www turbolinux com 46

HP Server tc2100 Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents