HP 7203dl User's Manual
Contents
1. 3 Attach the ring terminal to the chassis as shown in the figure to the right 4 Connect the other end of the ground wire to a suitable grounding point at your site 5 Apply power to the unit Note For information on installing the Encryption and Compact Flash modules please refer to the ProCurve Secure Router Installation Guide included in your router shipment RPS Input HP ProCurve ara ak O Line 50 60 Hz 100 127 V 0 8A 0 8A B Compact Flash 200 240 V 0 4A 0 4A CONNECT TO THE PROCURVE SECURE ROUTER 7203DL CONSOLE Before connecting to the ProCurve Secure Router 7203dI Console interface you will need the following items VT100 terminal or PC with VT100 terminal emulation software and the serial cable 5184 1894 supplied with your router This is the same console cable used in other ProCurve switches such as the 5300xl series 1 Connect the DB 9 female connector of your cable to the DB 9 DTE male Console interface on the front panel of the unit 2 Connect the loose end of the cable to the VT100 terminal or PC with terminal emulation software 3 Open a VT100 terminal session to the ProCurve Secure Router 7203dI using the following settings 9600 baud 8 data bits no parity bits and 1 stop bit Press lt Enter gt to activate the HP Command Line Interface 4 Enter enable at the gt prompt 5 Enter the password when prompted or press lt Enters gt if you have not yet set a password 6112. Copyright 2005 Hewlett Packard Development Company LP
3. 11 Enter enable password enablepw to set the Enable Security mode password Pin Name Description 12 Enter exit to return to the Enable mode 1 TX1 Transmit Positive 13 Enter write memory to save the current configuration to memory 2 TX2 Transmit Negative ENABLE WEB GUI ACCESS 3 RX1 Receive Positive 4 5 Unused To enable Web GUI access an IP address for an Ethernet port must be assigned Refer to Enable Telnet Access above HTTP and HTTPS are enabled by default but a username and 6 RX2 Receive Negative password must be configured The example below creates a username of manager and a password of webpw Once configured use a Web browser to access the IP address 7 8 _ Unused 1 Verify that the prompt of your unit displays config COMMANDS 2 Enter username manager password webpw to set the password 3 Enter exit to return to the Enable mode Refer to the SROS Command Line Interface Reference Guide provided on the SROS ProCurve Documentation CD for details on configuring the system using the command line interface 4 Enter write memory to save the current configuration to memory 5 Open your web browser and enter the unit s IP address into the browser address line e g http 2 2 2 1 Note For safety information for the routers and all modules please refer to the safety and ESD precautions in the ProCurve Secure Router Installation Guide included in your router shipment 61195890L1 13B April 2005 Printed in the USA
4. 95890L1 13B April 2005 www procurve com Copyright 2005 Hewlett Packard Development Company LP Quick Start Guide eae ProCurve Networking HP Innovation ProCurve Secure Router 7203dl J8753A ENABLE TELNET ACCESS CONSOLE PINOUT The following steps create an IP address 2 2 2 1 24 for Ethernet port 0 1 an enable password Pin Name Description of enablepw and a password of secretpw for Telnet access 1 Unused 1 At the config prompt enter interface eth 0 1 to access the configuration parameters for the Ethernet port located on the base unit 2 RD Receive Data input 2 Enter ip address 2 2 2 1 24 to assign an IP address to the Ethernet port using a 24 bit 3 TD Transmit Data output subnet mask 4 DTR Data Terminal Ready output 3 Enter no shutdown to activate the interface to pass data F 5 SG Signal Ground 4 Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode 6 DSR Data Set Ready input 5 Verify that the prompt of your unit displays config 7 RTS Request to Send output 6 Enter line telnet 0 4 to change the configuration parameters for the Telnet session 8 CTS Clear to Send input 7 Enter login to initiate Telnet access 9 _ Ginueed 8 Enter password secretpw to change the login password for the Telnet session 9 Enter exit to return to the Global Configuration mode l ae ETHERNET PINOUT 10 Verify that the prompt of your unit displays config
5. Quick Start Guide ProCurve Secure Router 7203dl J8753A 5991 2113 ProCurve Networking aot HP Innovation ProCurve 7203dI Hno Backup Secure Router Opt Module Needed J8753A r O Ba og Console Eth ot al Encryption Module INSTALL THE INTERFACE MODULE 1 Verify the unit is not connected to a power source 2 Optional To install the backup module carefully align the P1 connector on the interface module with the J1 connector on the backup module Using only fingertip pressure to ensure that neither circuit board bends or flexes firmly seat the connectors Secure the backup module to the interface module using the supplied screws and standoff posts 3 Slide the interface module into the option slot until the module is firmly positioned against the chassis Secure the screws at both edges of the module 5 To install the wide module align the module with the wide slot and slide the module into the chassis until it is firmly positioned against the backplane connectors Secure by tightening the screws GROUND THE ROUTER 1 Strip one end of the ground wire to the length required for the ring terminal Ground wire and ring terminal are supplied by the user For more detailed grounding specifications please refer to the ProCurve Secure Router Installation Guide 2 Crimp the ground wire to the ring terminal using a crimp tool of the appropriate size
Download Pdf Manuals
Related Search