HP 20cp Setup and Install
Contents
1. be necessary to lower the freezing point However since the heat transfer potential of water with glycol is lower the HP POD must be derated accordingly NOTE The water cycle must be drained completely and then purged using compressed air when storing or transporting at or below freezing temperatures Acceptable water quality specifications Water must be maintained per the following acceptable water quality standards Specific conductance at 25 C 0 2500 umhos cm 77 F Alkainy ves CaCO Chloride Cl Sodium Na 0 1000 ppm Phosphate Ortho PO If your water is out of range consult a water quality expert Water quality requirements 15 Piping materials Do not use the following interconnecting piping materials in a closed water system e Oxidizing biocides e Aluminum components e Brass components with high levels of zinc e Non stainless steel iron components Water precautions Take the following precautions before installation of the HP POD e Verify that all foreign matter and particulates are flushed from the system Water might be discolored during the initial flushing of the system Clear running water is the sign that all foreign matter and particulates have been flushed from the system e Evaluate the short term and long term system requirements against the available water capacity e Ensure that the chilled water loop is properly designed for liquid cooling systems and is separate from the sa2. HP Performance Optimized Datacenter 6 m 20 fi Site Requirements Information a Part Number 587017 002 March 2010 Second Edition Copyright 2009 2010 Hewlett Packard Development Company L P The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein Intended audience This document is for the person who installs administers and troubleshoots servers and storage systems HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels Contents ERE NR 4 About this AGN RE VE EU PR SNE 4 SIE PSP ONO OM a 12 25 a E E EA EE eect erecta eee eee edge fade dag degradert 4 Safety information cccccccccceesscsesssceesseeeeseeeesseeeeseeeeseeecsseeesseeeesseeeesseeeeseesesseeeesseeesseescsseeesssesesseeesseeesssesensas 4 System UH SS aneia a a i a S 5 POWE T oii i EEEE EEEE EE EEEE TETE EE RE RERE RERE REAR EE EERE EE TRE 5 Draing rearen aara E EEE E E EERE EEOAE EEEE AE E AE EA AEE EEEE EEEE 6 Optional connections to central facility infrastrUCtUre cccccccceceseceesseceesecesseceeseeecssececseeeseeecsseceesseseseeeesseeeegs 7 Enviro
3. aes 19 Convenience outlets ccccccesceesseeeseeeseeeeeeneeeeseceseeceecsaeeeseeceeseaeeeeeeseceaeeeeeeeeseaeeseecnseseaeeeneesnteeetaeeneeens 19 Grounding requirements issssasssnarsrssarssarnnconntessaashaesrsbartsandasbaaaeabaesbabsisibssanssabanthaniasbaasninahatarisabaneiesbsbaninaesbee gt 19 IT cable portals cccccccccccccssscecsseecsseceesecesseeeceeeecseeeeeeeesseeeceseeeseeeeeseeecsseeeeseesesseeecssececeeseseeeseeeeeesseeeegs 20 HP POD DELT t EEEn Ennn 20 HP POD Environmental Control System c ccccccccssscecssscessececsececeeccssececssececeeecssececssecesseeeesseeessseeeseesesseeessaes 20 Fire safety and security notifications rrarsrrrervrrrrervrerervrrrrnrerervrenennrrenvrerernrerernrrennrerernresennssennserennsesensesennser 21 Acronyms and abbrevidhions sa ite cer siirecutedsieenchessnecaiadinedide Ribedukedevedibele AEA EAA E AROR 22 Site requirements About this document This document outlines the installation requirements for a 6 m 20 ft HP POD These guidelines are for a qualified architectural or consulting engineering team to generate site specific documents for each HP POD installation The site specific installation documentation must comply with local building code jurisdictions Site preparation The HP POD must be installed on a surface capable of supporting approximately 24 948 kg 55 000 Ib The site location for the HP POD must be level 0 5 degrees tolerance Appropriate clearance fo
4. al location of your power and water connections consider the distance between the facility utilities and the HP POD The facility power connection must be installed in compliance with local electrical codes and regulations HP can provide engineering services to develop the site installation plan and drawings as a supplemental service Power requirements The HP POD is available in North American and International models Both models provide 145 kW redundant or 290 kW non redundant power for the critical load e The North American HP POD includes step down isolation transformers and requires two 400A 480V 3 phase delta feeds at 50 60 Hz e The International HP POD does not require transformers and requires two 400A 380 415V 3 phase wye feeds at 50 60 Hz All 3 phase HP POD feeders require that the neutrals and the equipment grounding conductors remain isolated Bonding of the two conductors is allowed at the power source only For higher density loads that require more power capacity both 400A inputs can be fed from the same source When a lower density critical load is used N N redundancy can be accomplished by connecting the two 400A feeds to independent sources Main input power Power management 17 hem Component S Main input power side B lugs and breakers located 2 behind dead front panels Main input power side A lugs and breakers located behind dead front panels 3 Landing pen
5. aries depending on whether the HP POD is empty or configured with IT equipment Computer racks and IT equipment add incremental weight to an empty HP POD and vary depending on customization Maximum weight of IT 1 364 kg 3 000 Ib equipment for each rack Maximum weight of IT 13 640 kg 30 000 Ib equipment for each HP POD Fully outfitted HP POD 22 500 kg 49 500 Ib 2 IMPORTANT Before moving the HP POD to a new location HP recommends contacting the local Department of Transportation for permit loads and other transportation requirements Required clearances NOTE Shaded areas indicate required clearances HP POD specifications 9 Top view em Component S Heat exchanger access panels Water input side view 110 CWR CWS portal Central facility infrastructure connection HP POD ECS Fire Security Phone Convenience outlet power HP POD specifications 10 Double door end view 96 000000 tem Component IT cable portals External cold aisle view Cass ee Controlled access keypad optional HP POD specifications 11 External hot aisle view 240 ai 120 Callout Main input power and B feeds Controlled access keypad optional Internal components The actual location of various components or subsystems in your HP POD might vary from this docum
6. entation For final placement specifications see your operations and maintenance manual ltem Component S O EPO controls and indicators HP POD specifications 12 Control cabinet interior ttem Component S Access control system components Fire alarm fire suppression system components Component backwall ASSD EPO le ol dd item 2 HP POD specifications 13 tem Component 9 Redundant power relays EPO controls and indicators Water supply specifications Feature Specification Facility input temperature to HP POD 12 to 24 C 55 to 75 F Working pressure 1034 kPa 150 psi HP POD pressure drop 1732 kPa 25 psi HP POD water flow rate 454 min 120 gal min Cooling water supply and return North America connections Two 7 62 cm 3 in ASME B16 5 class 150 flanges International Two DIN PN16 DN80 flanges Humidifier See the humidifier manual for exact requirements HP POD specifications 14 Water quality requirements Water quality requirements and specifications e Closed loop water must not contain any lime scale deposits or loose debris e The chilled water temperature to be supplied to the HP POD must be 12 to 24 C 55 to 75 F NOTE Freezing water might cause a blockage and damage to the unit In outside locations subject to freezing temperatures an additive such as glycol might
7. etration portal B for attaching incoming conduit connections for the main input 4 Landing penetration portal A for attaching incoming conduit connections for the main input Main input power details Power management 18 Supported facility connections Humidifier specifications A dedicated supply of domestic water is required if the optional humidifier is installed For exact requirements for the humidifier model that was installed see the humidifier manual supplied with the HP POD em Component Humidifier drain 2 Water supply For more information about the humidifier see the documentation developed by the humidifier manufacturer Convenience outlets The HP POD is prewired for a convenience outlet on the inside of the unit This circuit is not part of the power provided by the main switchboard feeding the 3 phase power to the HP POD To energize this circuit you must supply a dedicated single phase 16 or 20 amp branch circuit from your facility at the appropriate voltage Make sure that the branch circuit is connected to the prewired exterior mounted junction box and must be wired in accordance with local regulations and codes Grounding requirements The neutrals and equipment grounding conductors for all 3 phase HP POD feeders must remain isolated The two conductors can be bonded at the power source only Supported facility connections 19 Functional and supplementary grounding straps are
8. mplies with local workplace lighting regulations Make sure that the HP POD is properly grounded Avoid placing the HP POD directly along a drainage path or in an area prone to flooding Environmental specifications Features Specifications Operating temperature 18 C to 54 C 0 F to 130 F Supports to 29 C 20 F with optional cold weather protection installation Site requirements 7 Features Specifications O O Nonoperating 29 C to 54 C 20 F to 130 F temperature Operating humidity e 0 to 100 relative noncondensing Nonoperating humidity e 5 to 95 relative noncondensing e 39 C 102 F maximum wet bulb temperature Operating altitude 76 2 to 3 048 m 250 to 10 000 ft Non operating altitude 76 2 to 9 144 m 250 to 30 000 ft For nonoperating specifications consider the temperature of computer and IT equipment inside the HP POD The HP POD must be drained before it is moved to a new location For areas prone to freezing take appropriate water freeze protection precautions Lightning protection If the HP POD is installed in an outdoor environment then HP recommends hiring a lightning protection consultant to evaluate potential lightning risks and assess possible HP HP POD lightning protection schemes Site requirements 8 HP POD specifications Dimensions The HP POD is approximately 6 7 m 22 ft long 2 4 m 8 ft wide and 3 1 m 10 ft tall Weight HP POD weight v
9. nitary water systems in your building bathroom sink drinking water e Ensure facility managers are aware of the additional load being added to the chilled water supply of the building Be aware that the added heat load might affect other components being cooled by the chilled water plant Condensation management CAUTION During operation avoid leaving the HP POD doors open to maintain accurate environmental conditions inside the HP POD Supply cooling water that is above the dew point inside the HP POD to prevent condensation forming on the heat exchangers The heat exchanger drip tray will collect any condensation that forms on the heat exchangers This collected condensate drains out of the HP POD through the heat exchanger condensate drains HP recommends connecting condensate drains on the HP POD to a facility drain to prevent collection of water near the HP POD There is one heat exchanger condensate drain outlet located near the bottom of the HP POD in between the access doors on the hot aisle side There are three drains for the water main supply and return lines located near the bottom of the HP POD on the cold aisle side To avoid excessive buildup of condensate and to conserve energy raise the cooling water temperature to above the dew point to manage condensation while maintaining the necessary cooling capacity Water quality requirements 16 Power management Connection requirements When determining the fin
10. nmental considerations RES EE EES ESrES renne rsteat ennet 7 Environmental specifications rrrrrrrrrorvrrrrovvrnrovvrrrsvrnrenvrnnevnrrssnnnrenvrerennressnnnnennnerennerssnsersnnsessnsssesnsenen 7 rv 8 EE ERE 9 Dimensions pr 9 ET EE NN NN Le SN FN NR MR DE ES KE SEN ee 9 Required clearances vas 9 Internal componentS rrrrvrerorrrronvrerervrerevnrrennrerennrerernrrsnnrerennrerennresnnrerennresenaresnnrerennresennersnnserenesesenssssnnsesene 12 Water supply specifications cccccccscccsssecessececsseceeseeccsseeecseecceeecsseeecsseeeeseeecssesecsecesseescssecesseceseeseneeessaes 14 Fr Oa Wacoal stad cscs lecisacce eet ce lata ERNARI 15 Water quality requirements and specifications ccccccsscccsssceesssceeseeecsseeeesseecsseeecsseceesseeesseeeesseeessseseneeeesseees 15 Acceptable water quality specifications ccccccccsccsssecessscecsseeeesseeesseeecsseeeeseesesseeeesseeeesseeesseesenseeessaeees 15 Bel am EADS er er EE 16 Walerpecduions ektet ceteees 16 MS HTSUS Jie LIE L sj SEERE ete ee eo echt uu re ee hee tee nh eee 16 EE GE RR EE RES SS 17 Gonnettion EGU IPS MMS HS ce c s erea ere F s 0a 9 05 IA RRR RRRA RRRA eva ea eee en ee eS ev RRR 17 Power fequremens vasse 17 Map NE ascent aes ats at a ev a ws a a we aw aw aw aw aw an oe 17 Main input power details upassende 18 TN NN 19 Humidifier specifications cccccccccccssscessseccesececseceeseeeseeecsseeeseeeesseeessseeeseesesseeeesseeesseesesseeessseseeseesenseeens
11. ported facility connections 21 Acronyms and abbreviations ASSD air sampling smoke detector BMS building management system B S environmental control system EPO emergency power off POD Performance Optimized Datacenter TVSS Transient Voltage Surge Suppression Acronyms and abbreviations 22
12. provided between each rack and HP POD 2 IMPORTANT Before installing the HP POD consult your local AHJ for applicable codes and to review site specific location guidelines 2 IMPORTANT You must ground the HP POD to your ground grid system for full protection IT cable portals Six 63 5 mm 2 V inch IT cable portals on the double door end of the HP POD are available for optional Ethernet fiber optic and IT cable configuration These components are also used for optional ECS configuration and can support dedicated lines a customer network and various other communications service options You may install a weatherproof box for termination points on the outside of the HP POD over the cable portals Examples of cables that can run into the 63 5 mm 2 1 2 inch portals are as follows e 48 Cat 6 cables e 3912 strand multi mode or single mode fiber optic cables HP POD security The HP POD is equipped with standard key lock hardware at each entry door and external panel Conduit and junction boxes are provided for customer installed controlled access systems Optional controlled access security includes a 12 digit security code keypad and magnetic locks on all entry doors HP POD Environmental Control System The HP POD ECS is a stand alone system and does not require any connections to existing facility management infrastructure You can choose to connect to the facility BMS at additional cost BMS configuration communicates thro
13. r installation service and system utilities power and water must also be considered 2 IMPORTANT Before installing the HP POD consult your local AHJ for applicable codes and to review site specific location guidelines 2 IMPORTANT The HP POD is designed for ground level installation If you install the HP POD on an elevated surface make sure the minimum height requirements for circuit breaker actuators are considered per local and national electric code requirements The area in front of the outside panels must include a work platform The distance from the work platform surface to the center of any circuit breaker actuator handle must not exceed 183 cm 72 inches The platform must be a minimum of 91 cm 36 inches wide for free air and if the platform construction is grounded metal must be a minimum of 107 cm 42 inches wide Safety information The HP POD is certified to UL 69050 IEC 60950 as an Information Technology Product and Classified according to the National Electric Code NFPA 70 2008 The HP POD is not suitable for long term human occupancy The HP POD has service access areas for periodic maintenance and service These areas must be used only by owner authorized personnel who are trained in the maintenance and service of the HP POD IT components 2 IMPORTANT Before installing the HP POD consult your local AHJ for applicable codes and to review site specific location guidelines If needed obtain any necessary permi
14. ts Before installing your HP POD verify that the following prerequisites have been met e All components have been delivered to your facility e The HP POD power distribution components and water distribution components are in their final location e You have facility power at your final location Site requirements 4 e You have chilled water at your final location e You have made provisions for properly grounding the HP POD System utilities Your site location must accommodate the following utilities e Cooling water e Electrical power e Drainage Power Chilled water supply connection Chilled water return connection External communication box if fitted ECS Fire Security Telephone Site requirements 5 Item Component Main input power junction boxes Drainage Site requirements 6 Drain hot aisle view me Water main supply return drains Heat exchanger condensate drain Optional connections to central facility infrastructure HP POD ECS Life safety systems Convenience outlet power Site networking connection Domestic water for optional humidifier Security system optional Environmental considerations Optional Install under a properly engineered awning Install lightning protection for the HP POD Make sure that the HP POD is installed in a well lit area that co
15. ugh an Ethernet cable connected to the internal HP POD ECS panel jack located inside the junction box HP POD ECS data can be sent and viewed to a set IP address The HP POD ECS communicates through Modbus TCP protocol Modbus TCP is a data communication protocol for building automation and control networks The ECS offers e The ability to monitor status of water and air temperatures water pressures and water flow rates e Immediate notification of all supported alarm messages e Real time power consumption For additional points that can be monitored see the I O Input Output Controls Points List Supported facility connections 20 Fire safety and security notifications Dry contacts are provided to enable the connection between the fire alarm system and the central facility fire detection system relay alarm and trouble conditions at each HP POD Your building fire safety and security system relays the following alarms which operate independently of each other Smoke alarm Smoke has been detected in the HP Activate the EPO Follow standard POD emergency procedures for your facility Security security breach has occurred Follow standard emergency procedures for your facility EPO Someone has activated the EPO Follow standard emergency system and shut down the HP POD procedures for your facility The electrical layout of the fire alarm system is as described in the schematic drawing supplied with the HP POD Sup
Download Pdf Manuals
Related Search