HP 98624A User's Manual
Contents
1. HP 9000 Series 200 Computer Systems HP 98624A HP IB Interface Card Installation Note O packaro HEWLETT PACKARD COMPANY Manual Part No 98624 90000 Roseville Networks Division E0685 8000 Foothills Boulevard Printed in USA June 1985 Roseville California 95678 Printing History Printing History below identifies the Edition of this Manual and any Updates that are included Periodically update packages are distributed which contain replacement pages to be merged into the manual including an updated copy of this Printing History page Also the update may contain write in instructions Each reprinting of this manual will incorporate all past updates however no new information will be added Thus the reprinted copy will be identical in content to prior printings of the same edition with the user inserted update information New editions of this manual will contain new information as well as updates 98624 90000 A A A hi det a June 1981 Second Edition June 1985 RR oy NOTICE The information contained in this document is subject to change without notice HEWLETT PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Hewlett Packard shall not be liable for errors contained herein or for incidentai or consequential damages in connection with the furnis2. GNS P1 21 22 4 Baza Pr 4 gt GND P1 35 362 f GNO P1739 4G et GND P4147 4B D BAS PA 4B D gt nn cr GNO PI 61 B2 gt END P1 735 78 RESET paray de a 3 _ g Ues Ser rare ww waa a rwm A rw lt lt ee pe Bt RUDA A pe Oe x 6 f j 4 J ji 1 want ar Figure 3 HP 986244 Schematic Diagran
3. REN GND GND GND GND GND GND a 5 TRS 116 THS gt UJG REMOTE A IS a CONTROL A cr a tte 13 fo INT ESO DAY gt eb DAY Biri NDAL NAC Re NRE G Gwed 1 2 NGFT ana EGY ne ES cert EA 304 ATN AIN 51 11 ATN 305 SARR ne S110 SoA 306 HEN deed SY 47 BEIN BD IFC 4g TFC da TE CTRL TMSSG914A DIO Aucas ores gt 0102 pide DARRO PIA E ent i a D103 Oras DHANI 2102 GU PWN NA DIOS DIDA DHAR Pie me ACCRG a 2105 6108 SHACKT Pi 42 ACCOR DIOB GIGS as2 a Iro DIO t RSI Dios DIOB pue a pgs t 1 as GB EN Ba P1 56 gt La Aa mai Ue BA2 P4 54 gt A ns F BAG P3 52 Dereat i x BAA PEED Deu A RESET BALA 4 95 rs tB jis BLESS PIA gt Ir 19 et eo de EA GNO 44 59 GND d 26 GNO SEF Re ITEM 5 GNO BEFW ITEM G5 GNR Fo perras ee egl GRD HER O ERAN ERNE EDN Haan MEER RANK Jir22 GN ui 5 10 415 11 14 o Jig GND u 34 uh 14 44 j u ua 20 17 12 vw r gt 11 24 GND UA 44 via 20 20 Y A 01 9 mmm ua i 22 uo 8 14 DT R 1 34 Eon y 2 14 7 Uzi 42 44 Jied2 SHIELD TMA 91 41 Erne ua 17 1a 7 U22 3 14 End ua a B U23 8 29 uit 7 46 B u24 B 4a vii 7 d4 vas a 26 Wiz 15 E v 16 20 Wid 10 20 10 ya 4 20 U14 s 7 BAB 24 67 2 mwanzi hoi Bat 1 88 De ii gi 25V p1 8a5 gt Si BA1B P1 B9 gt Eom t5V 1 86 gt u aaa Yv 3413 P1 705 ii i 104 be C2 les BAZ PI 73 Deer MU ee Olut BAZI PE 73 eras SND 22 13 14 9 rro br Bao ie gt
4. hing performance or use of this material This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Copyright c 1981 1985 by HEWLETT PACKARD COMPANY HP 98624A HP IB Interface Card Installation The HP 98624A is an HP IB Interface Card for HP 9000 Series 200 Computers HP IB is Hewlett Packard s implementation of EEE 488 1978 This note describes the procedure for installing the 98624A Installing Interface Cards in the Series 200 Backplane The backplane of a Series 200 computer can contain from 2 to 16 card slots depending on the model of computer These card slots come in pairs each cover plate on the back of the computer covers one such pair of slots The lower slot of each pair can accept any Series 200 card interface memory or DMA the upper slot can accept only memory and DMA cards Thus interface cards must be inserted into the lower slot of a pair To install an interface card in the Series 200 backplane follow these instructions l Set the switches on the card according to the instructions in the section on Conf iguring the Interface Card 2 Turn the computer off 3 Interface cards must go into any of the slots just below a pair of cover bolt holes Remove the metal backplane covers one by one until yo
5. p as follows I Not System Controller 2 Interrupt Level 3 3 Select Code 8 4 Primary Address 0 if the default conf iguration is acceptable check to make sure that all the switches are set according to the diagram If you wish to reconfigure the interface refer to the accompanying drawing and the HP IB section of your 1 0 Programming Manual Y a a a ee O ef 4 POS 3 0 4 0 4 6 EMIR ros j IICA va r 2 0 0 1 SEL CODE REMOTE jumper Note 1 Out Engbied in Not Enabled Interrupt Level Switch ES See Tabie 1 1 ADRS 1 Note 2 HP 38 I SYS CTL Note 3 MSBE 1 System Controller O m Not System Controtier Fi E 5V 4A i Y rd NOTES I Select Code SEL CODE switches set for 8 2 Address Switches 1 ADRS 1 set for power up primary HP IB address of the card If you want this card to perform the functions of the computers internal HP 1B we recommend that you set the address to 21 if the card is the system controller or 20 if the card is not the system controller The driver interprets an HP IB address of 31 as an address of 0 3 The board is not set for system controller Figure 1 Configuration Switch Diagram Table 1 Interrupt Level Switch Interrupt Level DI DIO 0103 piga DAV NRFD NDAC IFG SHIELD GND Figure 2 HP 986244 HP IB Connector Diagram Switch Settings DIGS DIZ6 DI 7 DI68
6. u find an empty slot just below a pair of cover bolt holes 4 The metal plate on the interface card takes the place of a backplane cover A memory or DMA board may be instalied in the slot above the interface card 5 Slide the interface card into the slot component side up until it bottoms against the backplane connector board Then tighten the thumbserews until they are finger tight 6 If there are no empty slots just below a cover bolt hole pair you must rearrange the memory boards to accommodate the interface card Remove any memory board in a slot below a bolt hole pair and re install it in an empty slot above a bolt hole pair It is not necessary to change the address of the memory board as the computer CPU automatically finds the board at its new location 7 If there are no empty slots a memory board or interface card must be removed and left out if the new interface card is to be installed If a RAM memory board is left out make sure it has the lowest address 8 Connect the computer to the desired peripheral using an appropriate cable 9 Turn the computer and the peripheral on and operate according to the instructions in the appropriate operating manual If problems are encountered call the nearest HP Sales and Service Office Configuring the Interface Card Figure shows the location of all the configuring switches on the 98624A in the default factory set configuration In this configuration the interface card wakes u
Download Pdf Manuals
Related Search