HP 11i Quick Reference Guide
Contents
1. Pack 9905 See the HP ATM Release Note for any patches you might also need to install Z Class system firmware version e For Model V22xx Test Station software version 5 0 e For Model V2500 Test Station software version 1 1 Step 2 Check for Correct System Documentation Ensure that you have the appropriate manual for the HP 9000 system you are installing the adapter in Remember that as stated earlier qualified HP personnel must dothe installation for V Class servers Step 3 Ensure That You Have the Correct Hardware Software and Documentation Ensure that you have the following items Y OneHP PCl ATM 155 adapter product number A5513A or A5515A CAUTION Keep the HP PCI ATM 155 adapter in its protective antistatic bag until installation Electronic components can be damaged by even small amounts of static discharge So we highly recommend that you use antistatic procedures when handling this or any other computer component Handlethe adapter by the edges only and avoid touching all components and metal parts Do not store near strong electrostatic electromagnetic or radioactive fields y Onegrounding wrist strap Y OneUTP Cat5 loopback hood provided with the A5515A adapter only Z OneHP UX Applications Software CD containing the ATM link software Note that the ATM software is not locked So you do not need a codeword to unlock and install the software Z TheHP ATM RdeaseNote hardcopy or on the Ins2. EN 60825 2 1994 Wavelength 1300 nm Regulatory Information Optic Module The optic module provided in the HP A5513A and A5515A HP PCI ATM 155 adapters conforms to the ITU T recommendation G 957 cat l 1 or 1 4 For the United States Federal Communications Commission F CC Radio F requency Interference Statement This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that might cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Hewlett Packard s system verification tests were conducted with HP supported peripheral devices and cables such as those received with the system Changes or modifications to this equipment not expre
3. HP A5513A and A5515A HP PCI ATM 155 Adapters Installation Quick Reference Card Product Description TheA5513A HP PCI ATM 155 Multi M ode F iber MMF adapter A5515A HP PCI ATM 155 UTP Cat5 RJ 45 UTP Cat5 adapter and ATM link software make up a high performance solution for use in the HP 9000 V Class N Class and L Class Enterprise Servers and the HP VISUALIZE UNIX B1000 C3000 and J 5000 Workstations It has been designed to best meet high speed requirements and a large number of connections per HP system WARNING Only qualified Hewlett Packard personnel can install ATM adapters in the HP 9000 V Class Enterprise Servers Before Installing the HP PCI ATM 155 Adapter Before you install the HP PCI ATM 155 adapter do the following steps Step 1 Check the Hardware and Software Requirements Ensure that your hardware and software meet the applicable requirements Y Slot requirements y Number of adapters that can be installed simultaneously The HP ATM Rdease Note contains specific information about how many ATM adapters you can install in each type of system Z HP UX operating system version e For V22xx servers HP UX 11 0 plus Extension Pack 9905 e For V2500 servers HP UX 11 0 plus Extension Pack 9905 e For N Class servers HP UX 11 0 plus Extension Pack 9905 e For L Class servers HP UX 11 0 plus Extension Pack 9905 e For B1000 C3000 and J 5000 workstations HP UX 10 20 ACE or 11 0 plus Extension
4. not be held liable for errors contained herein or direct indirect special incidental or consequential damages in connection with the furnishing performance or use of this material Werranty A copy of the specific warranty terms applicable to your Hewlett Packard product and replacement parts can be obtained from your local Sales and Service Office 1999 Hewlett Packard Company all rights reserved Reproduction adaptation or translation of this document without prior written permission is prohibited except as allowed under the copyright laws UNIX is a registered trademark of The Open Group Safety Information WARNING All inputs outputs are Safety Extra Low Voltage SELV circuits CAUTION The hardware contains electronic components that can be damaged by static electricity To avoid damage follow these guidelines e Store the hardware in its conductive plastic bag e If possible work in a static free area e Handle circuit boards by the edges only Do not touch electronic components or electrical traces We strongly recommend that you use a grounding wrist strap that is connected to the metallic chassis of the host computer If you do not have a wrist strap touch the chassis before handling adapters and frequently thereafter to equalize any static charge LED Safety Information The optic module provided in the HP A5513A HP PCI ATM 155 adapter meets LED AEL Class 1 requirements per EN 60825 1 1994 A11 and
5. s A5483A A5483 60001 HP PCI ATM 622 MMF Adapter A5513A A5513 60001 HP PCI ATM 155 MMF Adapter A5515A A5515 60001 HP PCI ATM 155 UTP Cat5 Adapter Product Options All conforms to the following Product Specifications Safety IEC 950 1991 A1 A2 A3 A4 EN 60950 1992 A1 A2 A3 A4 A11 GB 4943 1995 IEC 825 1 1993 EN 60825 1 1994 A11 LED Class 1 EN 60825 2 1994 EMC CISPR 22 1993 EN 55022 1994 Class A GB 9254 1988 EN 50082 1 1992 IEC 801 2 1991 prEN 55024 2 1992 4 kV CD 8 kV AD IEC 801 3 1984 prEN 55024 3 1991 3 V m IEC 801 4 1988 prEN 55024 4 1993 0 5 kV Signal Lines 1 kV Power Lines Supplementary Information The product herewith complies with the requirements of the EMC Directive 89 336 EEC and carries the CE marking accordingly 1 The Product was tested in a typical configuration with Hewlett Packard information technology equipment Roseville CA March 1 1999 European Contact Your local Hewlett Packard Sales and Service Office or Hewlett Packard GmbH Department HQ TRE Herrenberger Stra e 130 D 71034 B blingen FAX 49 7031 14 3143 Copyright and Trademark Information The information in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall
6. ssly approved by Hewlett Packard could void the user s authority to operate the equipment For Canada For Canadian Regulations CES 003 Complies with Canadian Electromagnetic compatibility EMC Class A requirements Conforme a Classe A des normes canadiennes de compatibilit lectromagn tique CEM For Europe This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Copyright 1999 H ewlett Packard Company HP Part No A5513 90004 HEWLETT PACKARD Gi Printed in USA E1299
7. tant Information CD Z OneATM Configuration and Troubleshooting Guide hardcopy or on the Instant Information CD If any of the above items are missing please contact your HP representative NOTE When you unpack the adapter and ATM software keep all original packing materials for storing transporting or returning the product if necessary Step 4 Record the Product Identification Information Record the part number and date code of the adapter for future reference If the adapter needs service in the future HP service personnel will need the part number and date code This information is provided on a sticker attached to the adapter The sticker looks similar to this example A5513 60001 USA A XXXX The number in the upper left corner A5513 60001 in this example is the printed circuit assembly part number The 5 digit alphanumeric string in the lower right corner A xxxx in this example is the product version and date code Step 5 Check the Switch Specifications Check the following on the ATM switch vy It supports the appropriate interface for your HP PCI ATM 155 adapter MMF 155 Mbits second or UTP Cat5 155 Mbits second y thasSC or ST connectors if you are using the HP PCI ATM 155 MMF adapter Z ItisUNI 3 0 3 1 or 4 0 compliant Step 6 Ensure That You Have the Necessary Addresses Ensure that you have the needed addresses as follows Y For Classical IP installations you need
8. the ATM adapter s IP address and subnet mask Y For installations where the node will run as an ATM ARP client you need to know the ATM address of the ATM ARP server it will use Y For installations where you intend to use LAN emulation you need the following information An IP address and net mask for each emulated LAN e TheATM address of the LECS LAN emulation configuration server e Theselector ID Step 7 E nsure That You Have the Correct Cables Be sure you have the correct type of cable for the H P PCI ATM 155 adapter you are using Y MMF The adapter has SC connectors For connecting to ATM switches with ST connectors SC to ST duplex adapters are needed Check that you have the following cables as applicable e SC to SC cable e SC to ST cable duplex adapter e SC loopback connector for troubleshooting Z UTP Cat5 Use direct cables to connect to ATM switches Ina back to back configuration use a crossover cable to connect two adapters Installing the HP PCI ATM 155 Adapter WARNING Electric shock hazard Power off the system and disconnect it from the electricity supply before opening the system or accessing the slots Failure to do this can result in an electrical shock hazard and possible damage to the adapter or system For V Class servers qualified HP personnel must do the installation For all other HP 9000 systems follow the steps in the system documentation Be sure to follow an
9. tistatic precautions to help prevent static buildup that might cause damage Use an antistatic mat or a static controlled workstation and a grounding wrist strap to channel your own static charge safely to ground CAUTION Some of the components of the adapter are susceptible to damage by static discharge Degraded performance shortened product life or loss of operation can result from not observing precautions LED Colors and Meanings The HP PCI ATM 155 adapter has two LEDs R receive and T transmit The table below explains their colors and meanings Meaning None off A receive cable is correctly attached to the adapter Solid amber Theadapter is seated correctly in the system but no receive cable is attached to the adapter NOTE Ina back to back configuration a receive cable is attached to the adapter but the other system performed an atmstop Flashing green Data is being received This LED is off both when a transmit cable is correctly attached to the adapter and when notransmit cable is attached None off Flashing green Data is being transmitted DECLARATION OF CONFORMITY according to ISO IEC Guide 22 and EN 45014 Manufacturer s Name Hewlett Packard Company Internet amp Applications Systems Division Manufacturer s Address 8000 Foothills Blvd Roseville CA 95747 USA declares that the product Product Name HP PCI ATM Adapters Model Number
Download Pdf Manuals
Related Search