HP HEWLETT-PACKARD User's Manual
Contents
1. Figure 6 Eight Position Mini DIN Connector DIN Connector Pin Outs PIN Number Signal Name 1 active high input SIGNAL_DETECT 2 single ended driver RX_SIR 3 TP pins 3 and 6 TX Transmit Data 4 TP pins 4 and 7 PWR_GND 5 Receive Data Gnd RX_FIR 6 pulse data 0 TX Transmit Data 7 5 volt power 5V_POWER 8 pulse data 0 RX_FIR no connect for FIR EN HP Fast InfraRed Receiver 17 Declaration of Conformity according to ISO IEC Guide 22 and EN45014 Manufacturer s Name Hewlett Packard Company Manufacturer s Address 11311 Chinden Boulevard Boise Idaho 83714 1021 USA declares that the product Product Name HP Fast InfraRed Receiver Model Number C4103A Product Options ALL conforms to the following Product Specifications Safety IEC 950 1991 A1 A2 A3 EN 60950 1992 A1 A2 A3 A4 IEC 825 1 1993 EN 60825 1 1994 Class 1 Laser LED EMC CISPR 22 1993 A1 EN 55022 1994 Class B1 EN50081 1 1992 EN 50082 1 1992 IEC 801 2 1991 prEN 55024 2 1992 4 kV CD 8 kV AD IEC 801 3 1984 prEN 55024 3 1991 3 V m IEC 801 4 1988 prEN 55024 4 1992 0 5 kV Signal Lines 1 0 kV Power Lines FCC Title 47 CFR Part 15 Class B ICES 003 Issue 2 VCCI 21 AS NZS 3548 1992 CISPR 22 1993 Class B1 Supplementary Information The product herewith complies with the requirements of the following Directive and carries the CE marking accordingly the EMC direct2. warranty is exclusive of all other warranties whether expressed implied or statutory HP does not warrant Infrared Receiver for fitness for a particular purpose or merchantability HP will not be liable for any special consequential indirect or incidental damages even if advised of their possibility Some states do not allow for the exclusion or limitation of certain liabilities so the above limitations may not apply This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state HP Fast InfraRed Receiver 21 22 HP Fast InfraRed Receiver EN G HEWLETT PACKARD Expanding Possibilities Copyright 1999 Hewlett Packard Co
3. HEWLETT PACKARD Expanding Possibilities G English HP Fast InfraRed Receiver for HP LaserJet Printers and HP Mopiers User Guide HP Fast InfraRed Recelver for HP LaserJet Printers and HP Mopiers User Guide Copyright Hewlett Packard Company 1999 All Rights Reserved Reproduction adaptation or translation without prior written permission is prohibited except as allowed under the copyright laws First Edition February 1999 Hewlett Packard Company 11311 Chinden Boulevard Boise Idaho 83714 USA Warranty The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with respect to this information HEWLETT PACKARD SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Hewlett Packard shall not be liable for any direct indirect incidental consequential or other damage alleged in connection with the furnishing or use of this information Trademark Credits Microsoft MS Windows Windows and Windows NT are U S registered trademarks of Microsoft Corporation PostScript is a trademark of Adobe Systems Incorporated which may be registered in certain jurisdictions Table of Contents OMC Wet reos anio iaa indonesia ie ns System Requirements A AA ee Math oat fateh dae as Getting Started sc a bee NT
4. Provides wireless data transfer Transmits data at speeds up to 4 Mbps EN HP Fast InfraRed Receiver 3 4 Getting Started This section contains procedures for installing the HP Fast InfraRed Receiver The main steps include o Installing the HP Fast InfraRed Receiver e Installing the IR driver in Windows 9x or Mac OS Figure 1 HP Fast InfraRed Receiver Package Contents 1 HP Fast InfraRed Receiver 2 Velcro fasteners 3 User Guide HP Fast InfraRed Receiver EN Installing the HP Fast InfraRed Receiver EN Figure 2 IR Port on a HP LaserJet Printer Follow the instructions below to print a configuration page 4 2 Turn the printer s power switch off Attach the HP Fast InfraRed Receiver to the IR port on the rear of the HP LaserJet printer Turn the printer s power switch on On the control panel make sure the printer is on and the REND message is displayed Press Menu until the display reads TMFQEMATION MEHU HP Fast InfraRed Receiver 5 7 Press Select to print the configuration page The configuration page shows the printer s current configuration An HP JetDirect network configuration page will also print for networked printers and mopiers A configuration summary prints On the first page of the printout under Installed Personalities and Options check for IR POD IrDA Compliant The HP Fast InfraRed Receiver can be placed on a table or attach
5. UNE nee es Installing the HP Fast InfraRed Receiver Installing the IR Driver in Windows 9X Installing the IR Driver in Macintosh OS Printing with the HP Fast Infrared Receiver Setting Up to Print with Windows 9x Setting Up to Print with Macintosh Executing the Print Job Handling and Cale sd iii tenu o Cleaning the HP Fast InfraRed Receiver TroublESHOOLING ess San au a a een diese SPECE NONS See Ne A is done EN Product Specifications DIN PIR OUTS ea amet ra een Declaration of Conformity U S A Federal Communications Commission FCC Stalemenb u breit Canadian Department of Communications DOC STAIEMENE acid da Aa VCCI Statement Japan MEE RS O See EN HP Fast InfraRed Recelver Overview Thank you for purchasing the HP Fast InfraRed Receiver This device is an infrared IR adapter that complies with the communications protocol specifications established by the Infrared Data Association IrDA CAUTION EN Only connect the HP Fast Infrared Receiver to an HP LaserJet printer or mopier Connecting the HP Fast Infrared Receiver to a different device may damage the device The HP Fast InfraRed Receiver enables wireless printing from any IrDA complian
6. after the wizard is finished 3 Restart the computer Installing the IR Driver in Macintosh OS The HP Fast Infrared driver is pre installed with Mac OS 8 5 or newer If your Mac OS is older than 8 5 you can download the Apple LaserWriter 8 6 driver which supports IR printing from the World Wide Web at no charge from www apple com 8 HP Fast InfraRed Receiver EN Printing with the HP Fast Infrared Receiver Setting Up to Print with Windows 9x Before launching the HP Fast Infrared driver complete the following steps 4 From the Printers panel select your HP LaserJet printer as the default printer While in the same Printers panel go to Properties Details and make sure that Virtual Infrared LPT Port is selected Select the file to print Setting Up to Print with Macintosh EN Launch the Desktop Printer Utility Click the Printer Infrared from the New Printer window Click OK then click Change From the PostScript Printer Description window click the desired printer to print to From the File menu select Save From the File Browser window name your desktop printer then click Save Quit out of the Desktop Printer Utility HP Fast InfraRed Receiver 9 Executing the Print Job Align your portable computer or other portable device equipped with an IrDA compliant IR window within 1 meter 2 to 3 feet maximum of the HP Fast InfraRed Receiver The IR window must be at an angle of 15 degree
7. connection This object could be a hand paper books or even bright light Make sure that the two IR ports are clean free from dirt and grease Bright light of any kind sunlight incandescent light fluorescent light or light from an infrared remote control such as those used for TVs and VCRs shining directly into one of the IR ports may cause interference Make sure no bright light is shining directly into either IR port Position the portable device closer to the IR port on the printer 14 HP Fast InfraRed Receiver EN Troubleshooting Chart Continued Condition Solution The printer prints only part of a page or document The connection has been broken during transmission If you move the portable device during transmission the connection can be broken IrDA compliant devices are designed to recover from temporary connection interruptions You have up to 40 seconds to re establish the connection depending on the portable device being used The print job has been properly sent but the printer will not print If the connection is broken before the entire print job has been transmitted to the printer printing has not yet started the printer may not print any of the job Press the Job Cancel button to clear the printer s memory Then re position the portable device within the range of operation see Executing the Print Job on page 10 and print the job again The IR status
8. dures other than those specified in this manual may result in exposure to hazardous radiation 20 HP Fast InfraRed Receiver EN Warranty EN HP warrants that the HP Fast InfraRed Receiver will be free from defects and will meet the Infrared Receiver specifications as presented by HP at the time of original purchase for one year Under this warranty HP will at its sole option repair or replace any Infrared Receiver which is defective or does not meet the Infrared Receiver specifications Options cables accessories and included items are covered by the same warranty as the HP Fast InfraRed Receiver for which they are purchased Purchaser pays freight charges to return replaced equipment under this warranty If you think you have a defective Infrared Receiver call HP s Technical Support or your local sales office for assistance Warranty does not cover 1 Infrared Receivers with serial numbers that cannot be read 2 Infrared Receivers which have been operated with incompatible accessories Warranty will not cover damage resulting from 1 abnormal conditions including but not limited to accidents fire water etc 2 neglect or misuse of Infrared Receiver 3 causes external to the Infrared Receiver including but not limited to failure or fluctuation of electrical power air conditioning humidity control etc 4 maintenance repairs alterations or modifications performed by any person or entity other than HP This
9. ed to the side of the printer using the Velcro fasteners shown in Figure 3 on page 7 To attach the HP Fast InfraRed Receiver on the side of the printer continue with steps 1 and 2 1 Attach one Velcro faster to the round depression on the underside of the HP Fast InfraRed Receiver see Figure 3 2 Attach the remaining Velcro fastener to the side of the printer see Figure 3 When the HP Fast InfraRed Receiver is situated on the printer it should be close to the printer s front edge as shown in Figure 4 This location allows for the largest possible area in which the portable computer s IR port can operate The required alignment of devices is described in Executing the Print Job on page 10 6 HP Fast InfraRed Receiver EN Figure 3 Attaching the Velcro Fasteners Figure 4 HP Fast InfraRed Receiver After Installation EN HP Fast InfraRed Receiver 7 Installing the IR Driver in Windows 9x If your version of Windows does not have the HP Fast InfraRed driver pre installed you can download it from the Internet at no charge The address is http www microsoft com windows Use the search feature on the web page to locate the correct driver After downloading the Infrared driver complete these steps 1 Start the SETUP EXE program to invoke the Windows 95 Add Infrared Device wizard 2 When the wizard announces New Hardware Found events for the IR serial and parallel ports you can enable the IR device immediately
10. fraRed Receiver consult the support section of your user s guide Please have the following information available before you call Description of the problem e Version of Windows or Mac OS you are using Type of portable IrDA compliant device you are using o HP Fast InfraRed Receiver serial number and product number EN HP Fast InfraRed Receiver 13 Troubleshooting Chart Condition Solution IR port status indicator does not light up Make sure the printer is in EHEHE mode and that the IR port you are printing from is IrDA compliant and within the range of operation described in Executing the Print Job on page 10 Make sure the HP Fast InfraRed Receiver is properly connected to the printer Print the printer configuration page Check that IR POD IrDA Compliant is printed under Installed Personalities and Options Connection cannot be established or transmission seems to take longer than usual Use a device that is IrDA compliant look for an IrDA symbol on the device or refer to the computer user s guide for IrDA specifications Make sure that the operating system on your computer includes an IR driver and your application uses the appropriate HP LaserJet printer driver Note that complex pages take longer to print Position the HP Fast InfraRed Receiver within the range of operation see Executing the Print Job on page 10 and make sure that no object is blocking the
11. indicator turns off during transmission The connection may have been broken resume connection within 40 seconds Press the Job Cancel button to clear the printer s memory Then re position the portable device within the range of operation see Executing the Print Job on page 10 and print the job again PostScript print job will not print Check configuration in the PostScript tab of Windows check that Protocol is set to AppleTalk and Binary Data is not selected EN HP Fast InfraRed Receiver 15 Specifications Product Specifications Physical Dimensions Height 0 64 in 16 3 mm Width 1 70 in 43 0 mm Depth 3 07 in 78 0 mm Weight 8 oz Electrical Specifications Power Consumption During standby 0 4 W During transmission 2 0 W 400 mA Voltage 5 V DC Environmental Specifications Operating Temperature 50 to 91 F 10 to 32 5 C Operating Humidity Non operating Temperature 32 to 95 F 0 to 35 C 20 to 80 Non operating Humidity 10 to 95 Safety and Regulatory Conformance Safety Complies with IEC950 requirements Regulatory Cable Dimensions Cable FCC B VCCI 2 CE Marking 6 ft 1 8 m 16 HP Fast InfraRed Receiver DIN Pin Outs The HP Fast InfraRed Receiver uses the eight position mini DIN connector functional description of the pins follows
12. ive 89 336 EEC 1 The product was tested in a typical configuration with Hewlett Packard Personal Computer Systems 2 This Device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Compliance Information ONLY contact Australia Contact Product Regulations Manager Hewlett Packard Australia Ltd 31 41 Joseph Street Blackburn Victoria 3130 Australia European Contact Your Local Hewlett Packard Sales and Service Office or Hewlett Packard GmbH Department HQ TRE Standards Europe Herrenberger StraBe 130 D 71034 B blingen FAX 49 7031 14 3143 USA Contact Product Regulations Manager Hewlett Packard Company PO Box 15 Mail Stop 160 Boise ID 83707 0015 Phone 208 396 6000 18 HP Fast InfraRed Receiver EN U S A Federal Communications Commission FCC Statement EN This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communicatio
13. nected directly to the parallel port HP Fast InfraRed Receiver 11 Handling and Care The HP Fast InfraRed Receiver is a delicate electronic device that should be treated with the same care as your printer In addition follow these precautions at all times Avoid discharging static electricity to the HP Fast InfraRed Receiver Do not place objects on the HP Fast InfraRed Receiver Cleaning the HP Fast InfraRed Receiver Always keep the device s IR window free from dust and grease To remove dust from the HP Fast InfraRed Receiver s surface use a soft non abrasive cloth Hardened dirt may be removed with a cloth slightly dampened in soapy water Do not allow water to get into openings on the device Do not use abrasive cleaners acrylic or lacquer paint thinners and cleansers with an acetone or solvent base such as MDC or EDC These will damage the HP Fast InfraRed Receiver s plastic case 12 HP Fast InfraRed Receiver EN Troubleshooting If you have a problem while operating the HP Fast InfraRed Receiver follow these steps 1 Verify in your computer user s guide that your equipment is compatible with the HP Fast InfraRed Receiver fulfills system requirements and you have performed the correct hardware and software installation procedures 2 Seethe Troubleshooting Chart on page 14 to check if a solution to your problem is provided 3 If you still have a problem or think you may have a defective HP Fast In
14. ns However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna o Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Compliance to these regulations requires the use of shielded cables Changes or modifications to the equipment not expressly approved by Hewlett Packard could void the user s authority to operate it HP Fast InfraRed Receiver 19 Canadian Department of Communications DOC Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Requirements of the Canadian Department of Communications Compliance to these regulations requires the use of shielded cables VCCI Statement Japan Ozald TRUE RA O Ae VC CI DIEBE LEK OS 2B fei CI COR JERC PHS E EHRL TOETS ORNS VA PSLE Ya VY Seal TEL T EHe het ARE ARCADIA EY BORRA ChE TEL ORY BOEL CT FA WARNING Using controls making adjustments or performing proce
15. s to ensure an effective connection for printing Figure 5 illustrates the required alignment of devices necessary for printing Figure 5 Alignment of Devices Used for Printing 10 HP Fast InfraRed Receiver EN Note EN 2 Execute the print job The status indicator on the HP Fast InfraRed Receiver lights up ana ae a snot en the printer status panel displays a HMO Oe message If the status indicator does not light up realign the HP Fast InfraRed Receiver with the IR port on the sending device re send the print job and maintain the alignment of all devices as shown in Figure 5 If you have to move the equipment for example to add paper make sure that all devices remain within the range of operation shown in Figure 5 Only then is the required connection maintained If the connection is interrupted before your print job is complete the HP Fast InfraRed Receiver status indicator turns off You have up to 40 seconds to resume the connection and continue the job If the connection is resumed within this time the status indicator lights up again The connection is permanently broken if the sending port is moved out of operating range see Figure 5 or if anything passing between the ports blocks transmission for more than 40 seconds This block could be a hand paper or even direct sunlight Depending on the size of the job printing with the HP Fast InfraRed Receiver may be slightly slower than printing with a cable con
16. t portable device such as a portable computer to HP LaserJet printers and mopiers equipped for fast serial infrared operation Because this printer has HP JetSend Communications Technology built in the HP Fast Infrared Receiver also allows wireless printing from any HP JetSend enabled IR sending appliance The printing connection is maintained by positioning the sending IR port within operating range of the receiving IR port see Executing the Print Job on page 10 Note that the connection can be blocked by objects such as a hand paper direct sunlight or any bright light shining into either IR port System Requirements Note 2 In order to print with the HP Fast InfraRed Receiver you will need o HP LaserJet printer or mopier equipped with fast serial infrared capability o IrDA compliant portable or other IR capable host supporting IRLPT or HP JetSend over IR e Microsoft Windows 9x Mac OS 8 5 or Apple LaserWriter 8 6 driver or higher Older non IrDA compliant portable computers may not be compatible with the HP Fast InfraRed Receiver If you experience problems when attempting to printwiththe HP Fast InfraRed Receiver contact the manufacturer or dealer of your portable computer to verify compatibility with the IrDA standard HP Fast InfraRed Receiver EN Features e Complies with IrDA communications protocol specifications e Compatible with a wide variety of IrDA compliant portable computers eo
Download Pdf Manuals
Related Search