HP Bluetooth Active Noise Cancellation Stereo Headphones User's Manual
Contents
1. 9 e T f s 4 2 Chapter 1 Introduction ENWW Antenna House XSL Formatter Evaluation http www antennahouse com Before vou begin Before you set up your headphones read this section to determine the most appropriate connection for your computer or audio device This guide provides procedures for the following tasks e Charging the headphones e Connecting the headphones in the following Ways With the audio line in cable You can physically connect the headphones to your audio device with the audio line in cable Use this connection when a wireless connection is not available such as on an airplane For instructions on using this type of connection refer to Chapter 4 Using the headphones with the audio line in cable With the HP Bluetooth adapter provided with select models only You can wirelessly connect the headphones to the Bluetooth adapter when the adapter is inserted into the audio out headphone jack of your device For instructions on using this type of connection refer to Ghapter 5 Using the headphones with the Bluetooth adapter With a Bluetooth enabled device Yow Can wirelessly connect the headphones to a Bluetooth enabled audio device For instructions on using this type of connection refer to Chapter Using the headphones with Bluetooth enabled devices amp NOTE Ifyou do not have a Blu etooth enabled device but would like to add Bluetooth capability f2. headphones with a Bluetooth en ENWW Antenna House XSL Formatter Evaluation http www antennahouse com he wireless connection with your s for terminating the connection with the ENWW 19 Antenna House XSL Formatter Evaluation http www antennahouse com Terminating a wireless connection with the enclosed Bluetooth adapter select models only To terminate the connection complete the following steps 1 Slide the Bluetooth switch located on the left ear cup to turn off the headphones and deactivate Bluetooth 2 If this was the first use of the headphones and Bluetooth adapter and the pairing switch is in the on position slide the pairing switch up to turn off pairing In subsequent use it is not necessary to turn on pairing to establish a wireless connection with the Bluetooth adapter 3 Slide the power switch to turn off the Bluetooth adapter 1 4 Unplug the Bluetooth adapter from the audio out headphone jack 2 sof your computer or audio device 20 Chapter 7 Terminating the headphone wireless connection ENWW Antenna House XSL Formatter Evaluation http www antennahouse com Terminating_a wireless connection with a Bluetooth enabled computer To terminate the connection complete the following steps 4 3 4 5 6 Slide the Bluetooth switch located on the left ear cup to turn off the headphones and deactivate Bluetooth Open the Bluetooth Devices dialog box in one of the following wa
3. HP Bluetooth Active Noise CancellationStereo Headphones User Guide Antenna House XSL Formatter Evaluation http www antennahouse com Copyright 2007 Hewlett Packard Development Company L P Nothing herein shou constituting an ad P s not be liable for technical or editorial errors or omissions contained herein First Edition November Document Part Number 4591 Antenna House XSL Formatter Evaluation http www antennahouse com Table of contents 1 Introduction Identifying accessory Kit contents 2 eee sse eee een tener eee ae ee sees eee eese ennenen nnn nenen 2 BI AAV een correer Oo lt lt Sees 3 2 Identifying headphone components Left Side COMPOMENIS cccececceecee ee eeeeeee cere eecee ee MD T ene e cece eeaaeeeeeeeeeaaaeeeeeeeaaaeeeeeeeeaaaeeeeeeennneeeees 5 Right Side Ence T 6 3 Charging the headphones and Bluetooth adapter Select models only 4 Using the headphones with the audio _lin in cable 5 Using the headphones with the enclosed Bluetooth adapter provided with select models only 6 Using the headphones with a Blu tooth enabled computer Pairing using Vind ow eee B A aenn nnn nnn nnn 15 Pairing USING Windows XP once oe ee eee Oca asses esse ee enes sees nnn 17 7 Terminating the headphone wireless connection Terminating a wireless connection with the enclosed Bluetooth adapter select models only 20 Terminating a wireless connection with a Bl
4. e USB connector into the USB port on the AC adapter or computer 5 5 Ifyou are using the AG adapter plug the AC adapter into an AC outlet A WARNING Toreduce the risk of electric shock or damage to the equipmentsplug the AC adapter into an AC outlet that is easily accessible at all times The charging light on the left ear cup andion the Blu tooth adapter will turn on while the devices are charging and will turn off upon full charge After the charging Jights turn off the headphones and Bluetooth adapter are fully charged and ready to use ENWW 9 Antenna House XSL Formatter Evaluation http www antennahouse com 10 Chapter 2 Charging the headphones and Bluetooth a While the hea harging through the USB port on your computer you 2s to listen to computer audio gt see the Chapter 4 Using the headphones with the 6 the Regulatory Safety and Environmental elect models only ENWW Antenna House XSL Formatter Evaluation http www antennahouse com 4 Using the headphones with the audio line in cable To usethe headphones with the audio line in cable follow these steps 1 Make sure thatthe Bluetooth switch and the noise cancellation switch are in the off position with no red indicator visible at the open end of the switch 2 Plug one end of the audio line in cable into the audio out headphone jack on the left ear cup 3 Plug the other end of the audio lin in cable in
5. e the adapter discoverable by vour headphones The Bluetooth light 5 turns on to indicate that the adapter isin Pairing mode You are now ready to use the headphones Open your media player software and begin listening to music or watching a video ENWW 13 Antenna House XSL Formatter Evaluation http www antennahouse com 6 Usingthe headphones with a Bluetooth enabled computer NOTE To determine whether your computer is Blu tooth enabled look for the Bluetooth icon in the notification area at Ine Tar right of the taskbar on the computer screen Before using the headphones be sure that the following conditions are met e The headphones are charged e Your computer battery is fully charged e Your computer is turned on e Your computer is a Bluetooth enabled device Before you can use the headphones you must establish a Bluetooth wirelesseconnection with your computer a process called pairing Choose one of the following two sections depending on the operating system on your computer and follow the steps 14 Chapter6 Using the headphones with a Bluetooth enabled computer ENWW Antenna House XSL Formatter Evaluation http www antennahouse com Pairing using Windows Vista Ef NOTE Be sure that the cOmputer Bluetooth device is on and enabled For more information select Start gt Help and Support gt User Guides To pair the headphones using Windows Vista follow these steps 1 Slide t
6. he Bluetooth switch located on the leftear cup to turn on the headphones and activate Bluetooth Afred indicator is visible 2 indicating that the headphones are on 2 Slide the pairing switch on the right ear cup of the headphones to make the headphones discoverable by your computer 3 Select Start gt Control Panel gt Hardware and Sound gt Bluetooth Devices The Add Bluetooth Device Wizard opens ENWW Pairing using Windows Vista 15 Antenna House XSL Formatter Evaluation http www antennahouse com On the Devices tab cl 16 Chapter 6 Using the headphones with a Bluetooth en ENWW Antenna House XSL Formatter Evaluation http www antennahouse com Pairing using Windows XP NOTE Be sure that the computer Bluetooth device is on and enabled For more information select Start gt Help and Support gt User Guides To pair the headphones using Windows XP follow these steps 1A Slide the Bluetooth switch located on the leftear cup to turn on the headphones and activate Bluetooth Afred indicator is visible 2 indicating that The headphones are on 2 Slide the pairing switch on the right ear cup of the headphones to make the headphones discoverable by your computer ENWW Pairing using Windows XP 17 Antenna House XSL Formatter Evaluation http www antennahouse com Open the Bluetooth D completing either of the following steps eadphone icon 18 Chapter 6 Using the
7. lable only when the nes are used with a wireless Bluetooth connection dE om es ZS OS ENWW Right side components 7 Antenna House XSL Formatter Evaluation http www antennahouse com 3 Charging the headphones and Bluetooth adapter select models only Before vou Can use the headphones with the provided Bluetooth adapter select models only you must charge both the headphones and the Bluetooth adapter The headphones can be charged from the USB port on your computer or the provided AC adapter select models only To charge the headphones complete the following steps A CAUTION When removing the USB charging cablefrom adevice prevent damage to cable connectors by grasping each connector and then pulling gently Do not pull on the cable to remove it from the device 1 Be sure that the Bluetooth switch and the noise cancellation switch are in the off position with no red indicator visible at the open end of the switch 2 Plug one of the two Mini USB connectors into the Mini USB port on the headphones 1 The charging light 2 will turn on while the headphones are charging 3 Plug the other Mini USB connector into the Mini USB porton the Bluetooth adapter 3 The Bluetooth light 4 will turn on while the adapter is charging 8 Chapter 3 Charging the headphones and Bluetooth adapter select models only ENWW Antenna House XSL Formatter Evaluation http www antennahouse com 4 Plug th
8. or best results use anHP Bluetooth adapter Third party Bluetooth adapters may work but may not be supported e Terminating the headphones wireless connection A WARNING To reduce thefisk of personal injury adjustthe volume before putting on the headphones For additional safety information refer to the Regulatory Safety and Environmental Notices guide ENWW Before you begin 3 Antenna House XSL Formatter Evaluation http www antennahouse com 4 Chapter 2 Identifying headphone components ENWW Antenna House XSL Formatter Evaluation http www antennahouse com Left side components Component Description 1 Bluetooth switch e When the headphones are off slide the switch down to turn on the headphones and activate Bluetooth s When the headphones are on slide the switch up to turn off the headphonesjand deactivate Bluetooth 2 Charging light e On The headphones arescharging e Blinking The battery istow e Off The headphones are fully charged 3 Audio out headphone jack Gonnects the audio line in cable 4 Active Noise cancellation switch Reduces ambient sound when yourslide the switch down Slide this switch to activate the feature when you are in asndisy environment such as an airport ENWW Left side components 5 Antenna House XSL Formatter Evaluation http www antennahouse com Right side components Component Description 1 Volume down but
9. ound to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and usedin accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur inva particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by on or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment Antenna H
10. ouse XSL Formatter Evaluation http www antennahouse com
11. to the audio out headphone jack on your audio device such as a computer mobilephone or MP3 player 4 Open your media player software if necessary You can begin listening to music or watching a video ENWW 11 Antenna House XSL Formatter Evaluation http www antennahouse com 5 Using the headphones with the enclosed Bluetooth adapter provided with select modelsconly Before using the headphones be sure thatthe headphones and provided Bluetooth adapter select models only are charged To use the headphones with the Bluetooth adapter follow these steps 1 Slide the Bluetooth switch located on the left ear cup 1 to turn on the headphones and activate Bluetooth A red indicator 2 is visible indicating that the headphones_are turned on 12 Chapter 5 Using the headphones with the enclosed Bluetooth adapter provided with select ENWW models only Antenna House XSL Formatter Evaluation http www antennahouse com 2 When the headphones and Bluetooth adapter are being used for the first time slide the pairing switch to turn on pairing dn subsequentuses pairing does not need to be turned on 3 Plug the Bluetooth adapter into the audio out headphone jack of your audio device such as a computer mobile phone or MP3 player 1 4 Slide the power switch to turn on the Bluetooth adapter 2 A red indicator is visible 3 when ne Bluetooth adapter is turned on 5 Slide the Pairing switch 4 to mak
12. ton Decreases headphone volume 2 Previous rewind button Plays the previousstfack of a CD or the previous chapter of a DVD 3 Mini USB port Connects a mini USB cable for charging 4 Headphone status light e On The headphones are turned on and Bluetooth is activated e Blinking can indicate any ofthe following states Standby mode After the Bluetooth switch is turned on the headphones go intosstandby mode until you slide the switch up Pairing After you slide the Pairing switch up the light blinks until the headphones successfully pair with the audio device Paired When the headphones successfully pai with the audio device the light turns on andsth n blinks slowly e Off The headphones are off and Bluetooth is deactivated 5 Pairing switch Establishes a Bluetooth wireless connection with your computer when you slide the switch down 6 Next fast forward button Plays the next track of a CD or the next chapter of a DVD 7 Volume up button Increases headphone volume 8 Play pause button Plays or pauses audiowwhen Bluetooth is activated and pairing is successfully completed 9 SRS WOW Audio Technology on off Turns SRS WOW Audio Technology on and offewhen the volume Up and buttons volume down buttonsare pressed simultaneously 6 Chapter 2 Identifying headphone components ENWW Antenna House XSL Formatter Evaluation http www antennahouse com SRS WOW Audio Technology is avai
13. uetooth enabled computer 0 0 eeeeeeceeeeeeeeeeeeeeneaes 21 Us T ee P 22 ENWW iii Antenna House XSL Formatter Evaluation http www antennahouse com 1 Introduction HP Bluetooth Active Noise Cancellation Stereo Headphones allow you to wirelessly connection to an audio device Active noise cancellation reduces unwanted ambient sound such as the noise in a crowded airport By increasing the vacuum within the ear cupyactive noise cancellation produces noticeable audio improvement and sound Clarity SRS WOW Audio Technology available only with a Wireless Bluetooth connection takes digital sound to the next level Bass enhancement virtual Surround sound and innovative center control will further enhance your listening experience This guide provides steps for connecting the headphones to devices that are equipped with an audio out headphone jack or Bluetooth support Examples of these devices include the following e computer e mobile phone e MP3 player ENWW 1 Antenna House XSL Formatter Evaluation http www antennahouse com Identifying accessory kit contents In_addition to the documentation GD which contains this guide the following items are included in the headphone accessory kit 1 Headphones HP Bluetooth adapter provided with select models only Travel pouch 2 3 4 _Dual head USB charging cable 5 Audio line in cable 6 AC adapter provided with select models only 9
14. ys e Double click the Bluetooth icon in the notification arga at the far right of the taskbar on the computer screen P In Windows Vista select Start gt Control Panel gt Hardware and Sound gt Bluetooth Devices or e In Windows XP select Start gt Control Panel gt Bluetooth Devices Under Bluetooth Places click View Devices in Range in the Bluetooth Tasks section Right click the HP Bluetooth Audio Enthusiast Headphone icon Click Disconnect Click Unpair Your headphones can now be paired with anotherdevice ENWW Terminating a wireless connection with a Bluetooth enabled computer 21 Antenna House XSL Formatter Evaluation http www antennahouse com Index A noise cancellation 5 audio out headphone jack pairing 6 identifying 5 V B volume down button Bluetooth switch identifying 5 identifying 6 buttons volume up button identifying 6 next fast forward 6 play pause 6 previous rewind 6 SRS 6 volume down 6 volume up 6 C charging Bluetooth adapter 8 headphones 8 J jack audio out headphone 5 N next fast forward button identifying 6 noise cancellation switch identifying 5 P pairing switch identifying 6 play pause button identifying 6 previous rewind button identifying 6 S SRS buttons identifying 6 switches Bluetooth 5 22 Index ENWW Antenna House XSL Formatter Evaluation http www antennahouse com FCC Statement This equipment has been tested and f
Download Pdf Manuals
Related Search