HP A3694A User's Manual
Contents
1.2. computer unplug the power cord Remove the cover plate on the Processor Dual Bus HP HSC Expansion I O slot next to the primary HP HSC Expansion I O slot see Figure 1 by loosening the two one top and one bottom captive mounting screws See Figure 2 and pulling the cover plate away NOTE Backplane Card Slot Color Codes The following color bars appear above the slots on the system backplane Table1 Color Codes Color Slot Yellow HP PBO Green HP PB1 Blue Core lO Orange HP HSC Expansion I O primary Split Magenta Purple Optional HP HSC Secondary I O or additional Processor slots Purple Processor slots a HP9000 K 570 systems only I O and processor cards have matching color codes to assist in correctly matching the cards to the right slots Installation Procedures Installation Procedures Figure1 HP9000 K570 Rear View HPPB 10 4 HPPB 10 16 CORE I O EXPANSION I O E G L e g 6a 2D K 8 a c H J o z E 3 l i i bhop001 PROCESSORS 2 amp 3 DUAL BUS 4 SLOT HSC EXPANSION I O 7 Remove the adjoining processor slot s cover plate by loosening the two one top and one bottom captive mounting s
3. either wrist The other end of the strap connects to a convenient metal surface on the computer cabinet Anti Static Mat The anti static mat can be either the conductive bag the ESD sheet or the ESD foam pad The anti static mat does not have to be connected to the cabinet It should be placed close to the computer while performing the upgrade tasks Tools required To accomplish the upgrade procedures to the computer the following tools are required e A Torx 10 driver This is the preferred tool A flat blade screw driver this can be used if a Torx driver is not available e A3204 80004 ESD Kit e Flashlight or alternate light source recommended but not required Installation Procedures Installation Procedures Installation Procedures NOTE A 2 slot or 4 slot HP HSC Expansion I O product must be present in the primary HP HSC Expansion I O slot before adding the A3694A product to the secondary HP HSC Expansion 1 O slot 1 Log Off all users and stop all active applications that may be running N nou Aa W Perform a system backup of the entire Operating System and data base If this is not feasible perform a backup of the data base This should be done at a scheduled interval as common practice for protecting any new data or changes to the existing data base Perform a system shutdown Enter etc shutdown h at the prompt Turn the computer key switch to the STANDBY position At the rear of the
4. A3694A Dual Bus 4 Slot HP HSC Expansion I O Installation Guide HP9000 K 570 Enterprise Servers Edition 1 E0797 O HEWLETT PACKARD Part No A3694 90000 Printed in the U S A J uly 1997 Copyright 1997 by H ewlett Packard Company Legal Notices The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or direct indirect special incidental or consequential damages in connection with the furnishing performance or use of this material Restricted Rights Legend Use duplication or disclosure by the U S Government is subject to restrictions as set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 for DOD agencies and subparagraphs c 1 and c 2 of the Commercial Computer Software Restricted Rights clause at FAR 52 227 19 for other agencies HEWLETT PACKARD COMPANY 3000 Hanover Street Palo Alto California 94304 U S A Copyright Notices Copyright 1983 1997 H ewlett Packard Company all rights reserved Reproduction adaptation or translation of this document without prior written permission is prohibited except as allowed under the copyright laws Trademark Notices U
5. H P9000 systems have a primary HP HSC Expansion I O slot for upgrades This slot is immediately to the right of the Core I O card as viewed from the rear of the system refer to Figure 1 HP9000 K 570 systems can optionally use the slot to the right of the primary expansion I O slot for additional processors or as a secondary HP HSC Expansion I O slot The A3694A Dual Bus 4 Slot HP HSC Expansion I O product adds an additional four I O slots in this position Electrostatic Discharge CPU cards and computer systems contain assemblies and components that are sensitive to electrostatic discharge ESD Carefully observe the precautions listed in this section and use the ESD wrist strap ESD sheet and ESD foam pad provided in the ESD kit part number A3024 80004 The following precautions can significantly reduce the risk of system failure or component damage due to ESD e Always wear a grounded wrist strap when working around a system or handling the CPU card e Treat all assemblies components cards and connections as sensitive e When unpacking cards or components to the system keep the item in it s conductive bag until it is ready to be installed e Keep body movement toa minimum this generates static electricity that causes ESD e Avoid working in carpeted areas e Try toselect a work area where potential static sources are minimized Anti Static Wrist Strap The anti static wrist strap is a bracelet like strip that goes around
6. NIX is a registered trademark in the United States and other countries licensed exclusively through X Open Company Limited Reader Comments Reader Comments We welcome your comments about our documentation If you have editorial suggestions or recommend improvements for this document please write to us You can reach us through e mail at hardwaredocsGhp cup com or by sending your letter to Documentation Manager M S 5657 Hewlett Packard Company 9000 Foothills Blvd Roseville CA 95747 5657 USA Please include the following information in your message e Title of the manual you are referencing e Manual part number from the title page e Edition number or publication date from the title page e Your name e Your company s name SERIOUS ERRORS such as technical inaccuracies that may render a program or a hardware device inoperative should be reported to your HP Response Center or directly to a Support Engineer Preface This Installation Guide contains technical information about HP 9000 Computers The HP 9000 K xxo family of computers includes the following models HP9000 Kxx0O HP9000 Workstations Servers K100 HP VISUALIZE K260 EG K200 HP VISUALIZE K460 EG K210 HP VISUALIZE K460 XP K220 K250 K260 K270 K370 K400 K410 K450 K460 K570 NOTE The Dual Bus 4 Slot HP HSC Expansion I O Card may be installed ONLY on HP9000 K 570 systems 1 Installation Procedures HP9000 K 570 systems as with many other
7. cover plates that were removed are reinstalled and secure This is for proper seating of cards as well as cooling requirements 1 Reconnect the power cord to the rear of the computer 2 Turn the computer key to the ON position 3 Observe the Front panel Display and console for any error or fault F LT messages Installation Procedures Installation Procedures When all procedures are complete with no errors or faults the system needs to be re configured to add the new HP HSC path addresses Refer to the Owner s Guide for configuration instructions The HP HSC Slot path addresses are also the same as shown in Table 2 Table 2 HP HSC Slot Addresses Location Device Type Address Path Core I O card Optional I O connector HP HSC I O card 10 8 device addr Primary Four Slot HP HSC Expansion I O HP HSC I O Expansion card slot 0 HP HSC I O card 8 0 device addr HP HSC I O Expansion card slot 1 HP HSC I O card 8 4 device addr HP HSC I O Expansion card slot 2 HP HSC I O card 8 8 device addr HP HSC I O Expansion card slot 3 HP HSC I O card 8 12 device addr Secondary Four Slot HP HSC Expansion I O K570 only HP HSC I O Expansion card slot 0 HP HSC I O card 12 0 device addr HP HSC I O Expansion card slot 1 HP HSC I O card 12 12 device addr HP HSC I O Expansion card slot 2 HP HSC I O card 14 8 device addr HP HSC I O Expansion card slot 3 HP HSC I O card 14 12 device addr
8. crews and pulling the cover plate away This is necessary to gain access to the system board 8 Reach into the computer cabinet and remove the plastic dust cover from the HP HSC expansion connector on the system board 9 Remove the plastic dust cover from the Dual Bus 4 Slot HP HSC Expansion I O Card connector 10 Align the Dual Bus 4 Slot HP HSC Expansion I O Card into the card slot and slide it into the computer 11 When the card makes contact with the system board connector press the edge of the card to fully seat the card into the computer Tighten the two captive screws to secure the expansion I O card 12 Replace the CPU cover plate and tighten the two captive mounting screws Figure2 Screw Locations bhsm001 ioll eae i Ey Ey if E Hes Foil tel Pe Ee IP ee lf amp are o ue ia io r i ollo i o E at o a Ol ie te waa 5 5 o o t It i aor E EJ e n t870 iero joo JI ott ualt Installation Procedures Installation Procedures pet CAUTION ENT DUE TO REDUCE DAIRF LOW O CRITICALCOMPONENTS IAXIMUMDOBUTPUT If this completes the upgrade proceed to U pgrade Verification Upgrade Verification Before performing the procedures in this section make sure that all
Download Pdf Manuals
Related Search