HP 3C905-TX User's Manual
Contents
1. 12 When prompted insert the 3C905 driver s disk 2 of 2 and click on OK If you are using a Vectra VL7 follow the instructions below and then continue from step 15 If you are using a VL8 go straight to step 13 e Inthe Copying Files window the path should read A Win95 If you have an HP pre loaded HDD set the path statement to C MAS TERS LANDRV 3C905 Disk2 Win95 e Click on OK to continue the installation 13 Insert the 3C905 driver s disk 1 of 2 14 Set the path to A and click on OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk2 15 Click on OK to provide Computer and Workgroup names 16 At the Network dialogue box click on the Identification folder 17 Enter your Computer Name Workgroup and Computer Description 905 bk ch_2 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Netware 3 12 server Windows 95 SR2 and click on Close If you do not have a Computer name Workgroup name and Computer description contact your network administrator 18 At the Insert Disk notification click on OK 19 Set the path to your Windows 95 SR2 media and click on OK If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs 20 When prompted insert the 3C905 driver s disk 2 of 2 and click on OK 21 Set the path to2. 905 bk ch_10 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows 95 SR2 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM drivers disk 1 Etherlink 3C905 Ethernet Drivers Ver 2 1 and execute A 3C90XCFG EXE 5 Select Configure NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com software driver diskette and reboot the machine 8 When Windows 95 restarts a message will appear to indicate that new hardware has been found 9 Insert disk 1 of 3Com Etherlink 3C905 software ver 2 1 10 Click on Next to begin hardware wizard on the Update Device Driver Wizard dialog message 11 Click on Other Locations in the Update Device Driver Location dialog box and set path to A then click OK If you have an HP preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK1 12 3Com EtherLink XL TPO 10Mb Ethernet Adapter should now be listed click on Finish 13 Insert Disk 2 of 2 of the 3Com drivers disks and click OK in the Insert Disk dialog box 14 In Copying Files dialog box set path to A If you have an HP pre loaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 15 Click OK to continue installa
3. F10 9 At the Customize Support for Windows screen press F10 10 Select 32 bit LAN Drivers and hit the enter key 11 Page down the Board Drivers list to USER SPECIFIED 32 BIT DRIVER LIST and hit enter 12 Insert the 3COM Etherlink 3C905 Ethernet card and drivers disk 2 set the path to A Client32 and press enter 13 Select 3Com Fast Etherlink XL Etherlink XL and press enter 14 Accept the default frame types press F10 to continue and verify the following entries for the Installation Configuration Summary 15 YES 16 C NOVELL CLIENT32 17 C WINDOWS 18 32 bit LAN drivers 19 3Com Fast Etherlink XL Etherlink XL Driver 20 Press F10 to save and continue 21 When prompted insert the corresponding disks to complete file transfer and driver installation 22 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 23 After Windows loads open the NETWORK folder and double click the NETWORK SETUP icon 24 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only 25 Click on OK twice and the installation is complete 905 bk ch_4 fb4 Page 1 Thursday October 22 1998 9 51 AM Windows 95 SR2 Connecting to a Netware 4 1 server Windows 95 SR2 Connecting to a Netware 4 1 server Requiremen
4. and click OK 905 bk ch_7 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 3 51 20 Click on the OK button in the 3Com DRMON SmartAgent PC Software dialog box 21 Click on the Close button in the 3Com NIC Diagnostics v1 0 dialog box 22 Choose the default protocol TCP IP and any additional network protocols by clicking the check boxes in the Windows NT Setup dialog box and click Continue If you do not have the required information contact your network administrator 23 Check the boxes to add other TCP IP components and click on the Continue button 24 Click OK for the review of network settings in the Network Settings dialog box 25 If applicable approve the default settings in the NWLink IPX SPX Protocol Configuration 26 Set your IP address information in the TCP IP Configuration dialog box and click OK 27 If you do not have the required TCP IP Settings contact your network administrator 28 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 29 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box
5. 21 Highlight the TCP IP network component and click on the Properties button 22 If you know your TCP IP settings enter them in the TCP IP Properties dialog box otherwise leave the IP address choice checked Obtain an IP address automatically and click OK If you do not have the required information contact your network administrator 23 Click on Close and files will copy 24 Insert the Windows 95 CD ROM and click OK to the Insert Disk dialog box 25 When prompted enter the path for Windows 95 source files and click on OK in the Copying Files dialog box If you have an HP preloaded HDD set the path statement C MASTERS WIN95 SYSTEM CABS If you are using a Vectra VL8 go directly to step 26 If you are using a Vectra VL7 follow the instructions below to complete the installation e Click on OK to the Insert Disk dialog box e Set the path to A and click on OK If you have an HP preloaded HDD set the path to C MASTERS LAN 3C905 DISK1 e Click on Yes to finish the Setup installation and restart your comput er to the System settings Change dialog box 26 Click on Yes to finish the Setup installation and restart your computer to the System settings Change dialog box 905 bk ch_7 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 3 51 Connecting to a Windows
6. 905 bk ch_8 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 Connecting to a Windows NT Server 3 51 Windows NT Requirements Workstation 4 0 e HP Vectra with Windows NT Workstation 4 0 Service Pack 3 e 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 e Vectra VL8 Driver Name 3C90X SYS Size 74KB Date 1 09 98 e Vectra VLT Driver Name 3C90X INF Size 71KB Date 11 25 96 e Microsoft Windows NT Workstation 4 0 and Service Pack Media If you have a Hewlett Packard pre loaded HDD the media is located at CAI386 e Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 I O Base Address FCCOh FCCOh PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C905 PCI 905 bk ch_8 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 adapter card into a PCI slot 2 Connect network media to the 3COM 3C905 PCI card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM Etherlink 3C905 Ethernet card and drivers Disk 1 ver 2 1 and e
7. Etherlink XL Adapter 3C90X NDIS2 NDIS3 is selected in Network Drivers 16 Accept the applicable Network Protocols and then click on CLOSE e 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 e Microsoft NetBEUI e IPX SPX Compatible Transport with NetBIOS 17 lf you do not have the required information contact your network administrator 18 At the Network Setup dialog box click on OK 19 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK 20 Insert disk 2 and set Install Driver path to A MSLANMAN DOS DRIVERS ETHERNET EL90X and click OK to complete file copying If you have an HP preloaded HDD set the path to 905 bk ch_5 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 C MASTERS DRIVERS LAN 3C905 DISK 1 MSLANMAN DOS DRIVERS ETHERNET EL90X 21 Finish the network card installation by clicking on OK in the Network Setup message 22 To complete the installation click on the Restart Computer button in the Windows Setup dialog box 905 bk ch_6 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Microsoft Windows 95 SR2 Connecting to a Windows NT Server 3 51 Microsoft Windows 95 Requirements ane e HP Vectra with Plug and Play enabled r
8. OK 11 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 12 Click OK to accept the default choice of Unlisted or Updated Network Adapter 13 Type the path A WFW311 in the Install Driver dialog box and then insert the 3COM 3C905 drivers disk 1 of 2 into the floppy drive and click OK on Install Driver dialog box If you have an HP preloaded HDD set path to C Masters LanDrv 3C905 Disk1 WFW311 14 Select 3Com Fast Etherlink XL Etherlink XL Adapter 8C90X in the Unlisted or Updated Network Adapter dialog box and click OK 15 Make sure that the 3Com Fast Etherlink XL Etherlink XL Adapter 8C90X NDIS2 NDIS3 is selected in Network Drivers 16 Accept the applicable Network Protocols and then click on CLOSE 17 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 Microsoft NetBEUI IPX SPX Compatible Transport with NetBIOS 18 Ifyou do not have the required information contact your network administrator 19 At the Network Setup dialog box click on OK 20 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK 905 bk ch_9 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows for Workgroups ver 3 11 21 Insert disk 2 and set Install Drive
9. click on OK 19 Set the path to your Windows 95 SR2 media and click on OK If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs 20 When prompted insert the 3C905 driver s disk 2 of 2 and click on OK 21 Set the path to A and click on OK If you have an HP preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk2 22 Click on YES to complete installation and restart the machine 905 bk ch_5 fb4 Page 1 Thursday October 22 1998 9 51 AM Windows for Workgroups Ver 3 11 Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 Connecting to a Windows NT Server 3 51 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C905 Ethernet card and drivers disk ver 4 3 NDIS Driver Name E190X 386 Size 72KB Date 1 29 98 Microsoft Windows NT Server 3 51 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY e I O Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink HI 3C905 adapter card into a PCI slot Connect network cable media to the 3COM 3C905 card Power on the machine and set Plug and Play in CMOS to off
10. 14 Insert the 3COM 3C905 drivers disk 1 into the floppy drive 15 Change the path to A for the Insert Disk dialog and click OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk1 If you are using a Vectra VL8 go directly to 16 If you are using a Vectra VLT follow the instructions below and then go to 18 e 1 Select 3Com Fast Etherlink XL Adapter 8C905 and click OK e 2 With 3Com Fast Etherlink XL Adapter 3C905 listed in the Net work Adapters window click on Next 16 Select 3Com Fast Etherlink Etherlink XL PCI Busmaster NIC and click OK 17 With 3Com Fast Etherlink Etherlink XL PCI Busmaster NIC listed in the Network Adapters window click on Next 905 bk ch_12 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 18 Accept the default Network Protocol TCP IP and click on any additional protocols then click Next If you do not have the required Protocols information contact your network administrator 19 At the Network Services prompt accept default settings and click on Next 20 Finish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard preloaded HDD set the path to C I386 22 Insert the 3COM 3C905 driv
11. WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 1 0 Base Address FCCOh PCI FCCOh PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C905 PCI 905 bk ch_12 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 adapter card into a PCI slot 2 Connect network media to the 3COM 3C905 PCI card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM Etherlink 3C905 Ethernet card and drivers Disk 1 ver 2 1 and execute A 8C90XCFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com card drivers diskette and reboot the machine 8 Power on the machine and allow it to boot to Windows NT Workstation 4 0 9 Log onto the machine with Administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel group and double click the Network icon 11 Click on the Yes button and agree to install Windows NT Networking 12 With Wired to the Network checked click on Next 13 Click the option to Select from list then on Have Disk
12. disk 1 of 3Com Etherlink 3C905 software ver 2 1 10 Click on Next to begin hardware wizard on the Update Device Driver Wizard dialog message 11 Click on Other Locations in the Update Device Driver Location dialog box and set path to A then click OK If you have an HP preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK1 12 3Com EtherLink XL TPO 10Mb Ethernet Adapter should now be listed click on Finish 13 Insert Disk 2 of 2 of the 3Com drivers disks and click OK in the Insert Disk dialog box 14 In Copying Files dialog box set path to A If you have an HP pre loaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 15 Click OK to continue installation 16 Click OK to the Network dialog box to provide computer work group names 17 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 18 Click on the Configuration folder in the Network dialog box 19 Click on Add and then protocol from Select Network Component Type and click on Add 20 Pick Microsoft from the Manufacturers and TCP IP and then click OK 905 bk ch_6 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Microsoft Windows 95 SR2
13. 5 adapter card into a PCI slot 905 bk ch_11 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation Ver 3 51 2 Connect network cable media to the 3COM 3C905 card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM software 3C905 Ethernet drivers disk ver 2 1 execute A 3C90XCFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com software driver diskette and reboot the machine 8 After Windows loads log onto the machine with administrator privileges If you do not have the required information contact your network administrator 9 Open the Main Program Group double click on the Control Panel icon 10 Select the Network icon in the Control Panel program group 11 Click on YES in the Network Settings dialog box and NT Networking will be installed on your computer 12 Insert the Windows NT Workstation CD 13 In Windows NT Setup set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to CAI386 14 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card
14. 905 driver s disk 1 of 2 10 Set the path to A and click on OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk1 11 3Com Etherlink XL TPO 10Mb Ethernet Adapter should now be listed Click on Finish 12 When prompted insert the 3C905 driver s disk 2 of 2 and click on OK If you are using a Vectra VL8 go directly to step 13 If you are using a Vectra VL7 follow the instructions below then go to step 15 e Inthe Copying Files window the path should read A Win95 If you have an HP pre loaded HDD set the path statement to C MAS TERS LANDRV 3C905 Disk2 Win95 e Click on OK to continue the installation 13 Insert the 3C905 driver s disk 1 of 2 14 Set the path to A and click on OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk2 15 Click on OK to provide Computer and Workgroup names 905 bk ch_4 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Netware 4 1 server Windows 95 SR2 16 At the Network dialogue box click on the Identification folder 17 Enter your Computer Name Workgroup and Computer Description and click on Close If you do not have a Computer name Workgroup name and Computer description contact your network administrator 18 At the Insert Disk notification
15. A and click on OK If you have an HP preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk2 22 Click on YES to complete installation and restart the machine 905 bk ch_3 fb4 Page 1 Thursday October 22 1998 9 51 AM Windows for Workgroups Connecting to a Netware 4 1 server Windows for Workgroups Connecting to a Netware 4 1 server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 Vectra VL8 Driver name 3C90X LAN Size 33KB Date 2 5 98 Vectra VL7 Driver name EL9OXIDS INF Size 2KB Date 2 23 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols 32 bit Netware client for DOS and MS Windows Device Configuration Network Driver Optimization Normal e Full Duplex Auto Select N Way e Boot PROM Disabled e Media Type Auto Select N Way Vectra VL8 Vectra VL7 I O Base Address FCCOh PCI FC40h PCI Interrupt 9 PCI 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Fast Etherlink 3C905 905 bk ch_3 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Netware 4 1 server Windows for Workgroups adapter card into a PCI slot 2 Power on the machine and allow it to boot to a DOS prompt 3 Insert the 3COM drivers diskette and execute 3C90XCFG E
16. After booting insert the 3COM s drivers disk Etherlink 3C905 Ethernet ver 4 3 and execute A 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above 905 bk ch_5 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3COM Drivers diskette and reboot the machine 8 After windows loads open the NETWORK program group and double click on Network Setup icon 9 Select the Networks button in the Network Setup dialog box 10 Click on the Install Microsoft Windows Network option and click OK 11 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 12 Click OK to accept the default choice of Unlisted or Updated Network Adapter 13 Type the path A WFW311 in the Install Driver dialog box and then insert the 3COM 3C905 drivers disk 1 of 2 into the floppy drive and click OK on Install Driver dialog box If you have an HP preloaded HDD set path to C Masters LanDrv 3C905 Disk1 WFW311 14 Select 3Com Fast Etherlink XL Etherlink XL Adapter 8C90X in the Unlisted or Updated Network Adapter dialog box and click OK 15 Make sure that the 3Com Fast Etherlink XL
17. Close 26 If you know your TCP IP settings click NO and enter the IP settings when prompted 27 If You DO NOT know your TCP IP settings click on YES to obtain an IP address automatically and continue If you do not have the required information contact your network administrator 28 At the Show Bindings for window accept default entries and click Next 29 When Windows NT is now ready to start the network appears click on Next 30 If the message Could not find DHCP client appears click on NO to disable the message 31 Specify your Computer Name Workgroup or Domain and click on Next 32 If you do not have the required information contact your network administrator 33 At Network has been installed on this computer click on Finish 905 bk ch_8 fb4 Page 4 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 34 To complete the installation select Yes to reboot your computer 905 bk ch_9 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows for Workgroups ver 3 11 Connecting to a Windows NT Server 4 0 Windows for Workgroups Requirements ver 3 11 e HP Vectra with DOS and MS Windows for Workgroups 3 11 installed e 3COM Etherlink 3C905 Ethernet card and drivers disk ver 4 3 e DOS ODI Name Vectra VL alone EL90X DOS Size 46KB Da
18. Connecting to a Netware 3 12 server Windows for Workgroups Connecting to a Netware 3 12 server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 Vectra VL8 Driver Name 3C90X LAN Size 33KB Date 2 5 98 Vectra VL7 Driver Name EL9OXIDS INF Size 2K Date 2 23 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols 32 bit Netware client for DOS and MS Windows Device Configuration Network Driver Optimization Normal Full DuplexAuto Select N Way Boot PROM Disabled Media Type Auto Select N Way Vectra VL8 Vectra VL7 I O Base Address FCCOh PCI FC40h PCI Interrupt Request 9 PCI 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Fast Etherlink 3C905 905 bk ch_1 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Netware 3 12 server Windows for Workgroups adapter card into a PCI slot 2 Power on the machine and allow it to boot to a DOS prompt 3 Insert the 3COM drivers diskette and execute 3C90XCFG EXE 4 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 5 If changes are required save those changes and exit 6 Remove the 3Com cards driver diskette and insert 32 bit Netware client for DOS and MS Windows dis
19. Detection dialog box 15 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 16 Set the path to A in the Insert Disk dialog box and then insert the 3COM 3C905 drivers disk 1 If you have an HP preloaded HDD set path to C Masters LanDrv 3C905 disk1 17 Click OK at the Install Driver dialog box 18 Select 3Com Fast Etherlink XL Adapter 8C905 in the Select OEM Option dialog box and click OK 19 When prompted insert 3Com Etherdisk for Fast Etherlink XL disk 2 and click OK 905 bk ch_11 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation Ver 3 51 20 Click on the OK button in the 3Com DRMON SmartAgent PC Software dialog box 21 Click on the Close button in the 3Com NIC Diagnostics v1 0 dialog box 22 Choose the default protocol TCP IP and any additional network protocols by clicking the check boxes in the Windows NT Setup dialog box and click Continue If you do not have the required information contact your network administrator 23 Check the boxes to add other TCP IP components and click on the Continue button 24 Click OK for the review of network settings in the Network Settings dialog box 25 If applicable approve the default settings in the NWLink IP
20. Kin HEWLETT PACKARD Fast Etherlink XL TX PCI Network Interface Card 10 100BT 3C905 TX Installation Guide 905 bk fcover fb4 Page 2 Thursday October 22 1998 9 51 AM Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation MMX is a trademark of Intel Corporation Pentium is a registered trademark of Intel Corporation Hewlett Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France 1998 Hewlett Packard Company 905 bk ch_1 fb4 Page 1 Thursday October 22 1998 9 51 AM Windows for Workgroups
21. NT Server 3 51 Windows NT Requirements Workstation 3 51 HP Vectra with Microsoft Windows NT Workstation 3 51 installed 3COM Etherlink 30905 ethernet card and drivers disk ver 2 1 Vectra VL8 Driver Name DRMONNT INF Size 16KB Date 1 23 98 Vectra VL7 Driver Name OEMSTEUP INF Size 41KB Date 3 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 IIOBaseAddress FCCOh PCI FC40h PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C905 adapter card into a PCI slot 905 bk ch_7 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 3 51 2 Connect network cable media to the 3COM 3C905 card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM software 3C905 Ethernet drivers disk ver 2 1 execute A 3C90XCFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com softwar
22. VL7 finish the installation by following the instructions below e Set the path to A and click on OK If you have an HP preloaded HDD set the path to C MASTERS LAN 3C905 DISK1 e Click on Yes to finish the Setup installation and restart your comput er to the System settings Change dialog box 26 Click on Yes to finish the Setup installation and restart your computer to the System settings Change dialog box 905 bk ch_11 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation Ver 3 51 Connecting to a Windows NT Server 4 0 Windows NT Requirements Workstation Ver 3 51 HP Vectra with Microsoft Windows NT Workstation 3 51 installed 3COM Etherlink 30905 ethernet card and drivers disk ver 2 1 Vectra VL8 Driver Name DRMONNT INF Size 16KB Date 1 23 98 Vectra VL7 Driver Name OMESETUP INF Size 41K Date 3 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 I O Base Address FCCOh PCI FC40h PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C90
23. X SPX Protocol Configuration 26 Set your IP address information in the TCP IP Configuration dialog box and click OK 27 If you do not have the required TCP IP Settings contact your network administrator 28 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 29 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box 905 bk ch_12 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Connecting to a Windows NT Server 4 0 Windows NT Requirements Workstation 4 0 e HP Vectra with Windows NT Workstation 4 0 Service Pack 3 e 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 e Vectra VL8 Driver Name 3C90X SYS Size 74KB Date 1 09 98 e Vectra VLT Driver Name 3C90X INF Size 71KB Date 11 25 96 e Microsoft Windows NT Workstation 4 0 and Service Pack Media If you have a Hewlett Packard pre loaded HDD the media is located at CAI386 e Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N
24. XE 4 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 5 If changes are required save those changes and exit 6 Remove the 3Com cards driver diskette and insert 32 bit Netware client for DOS and MS Windows disk 1 If you are using a Vectra VL8 go straight to step 7 If you are using a Vectra VL7 follow the instructions below to complete the installation a Execute INSTALL EXE and set lines 1 5 as listed below e CANWCLIENT e YES e YES e C WINDOWS e NO e 3COM Etherlink XL Fast Etherlink XL Family Use driver provid ed on the 3Com driver s disk 1 b Highlight option 6 to continue with installation c When prompted insert the corresponding disks to complete file trans fer and driver installation d When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to re start the machine e After Windows loads open the NETWORK folder and double click the NETWORK SETUP icon f Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the follow ing network only g Click on OK twice and the installation is complete 7 Execute INST_DOS EXE and press enter to accept the agreement 905 bk ch_3 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Netware 4 1 server Windows for Workgroups 8 Accept the default installation options by pressing
25. bk ch_12 fb4 Page 4 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 34 To complete the installation select Yes to reboot your computer 905 bk bcover fb4 Page xxxvii Thursday October 22 1998 9 51 AM 905 bk bcover fb4 Page xxxviii Thursday October 22 1998 9 51 AM Version Number 3COM 905 Rev 1
26. disk 2 set the path to A Client32 and press enter 13 Select 3Com Fast Etherlink XL Etherlink XL and press enter 14 Accept the default frame types press F10 to continue and verify the following entries for the Installation Configuration Summary 15 YES 16 C NOVELL CLIENT32 17 C WINDOWS 18 32 bit LAN drivers 19 3Com Fast Etherlink XL Etherlink XL Driver 20 Press F10 to save and continue 21 When prompted insert the corresponding disks to complete file transfer and driver installation 22 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 23 After Windows loads open the NETWORK folder and double click the NETWORK SETUP icon 24 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only 25 Click on OK twice and the installation is complete 905 bk ch_2 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Netware 3 12 server Windows 95 SR2 Connecting to a Netware 3 12 server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 File Name OEMSETUP INF Size 41KB Date 3 14 97 Windows 95 SR2 media If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Novell Netware 3 12 s
27. e driver diskette and reboot the machine 8 After Windows loads log onto the machine with administrator privileges If you do not have the required information contact your network administrator 9 Open the Main Program Group double click on the Control Panel icon 10 Select the Network icon in the Control Panel program group 11 Click on YES in the Network Settings dialog box and NT Networking will be installed on your computer 12 Insert the Windows NT Workstation CD 13 In Windows NT Setup set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to CAI386 14 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 15 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 16 Set the path to A in the Insert Disk dialog box and then insert the 3COM 3C905 drivers disk 1 If you have an HP preloaded HDD set path to C Masters LanDrv 3C905 disk1 17 Click OK at the Install Driver dialog box 18 Select 3Com Fast Etherlink XL Adapter 8C905 in the Select OEM Option dialog box and click OK 19 When prompted insert 3Com Etherdisk for Fast Etherlink XL disk 2
28. ers disk 2 into the floppy drive and hit Enter If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 23 After the files transfer from Disk 2 you will be prompted to provide the path to your NT files DO NOT follow this direction Ignore the request an set the path to A on disk 2 of 2 instead If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 24 When the setup message 3Com dRMON SmartAgent appears click on OK 25 At the 3Com NIC Diagnostics v1 0 message click on Close 26 If you know your TCP IP settings click NO and enter the IP settings when prompted 27 If You DO NOT know your TCP IP settings click on YES to obtain an IP address automatically and continue If you do not have the required information contact your network administrator 28 At the Show Bindings for window accept default entries and click Next 29 When Windows NT is now ready to start the network appears click on Next 30 If the message Could not find DHCP client appears click on NO to disable the message 31 Specify your Computer Name Workgroup or Domain and click on Next 32 If you do not have the required information contact your network administrator 33 At Network has been installed on this computer click on Finish 905
29. erver that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Network Driver Optimization Normal Full Duplex Disabled Boot PROM Disabled Media Type 10BASE T Vectra VL8 Vectra VL7 I OBase Address FC40h PCI FCCOh PCI Interrupt Request 11 PCI 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink HI 3C905 905 bk ch_2 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Netware 3 12 server Windows 95 SR2 adapter card into a PCI slot 2 Power on the machine and restart Windows 95 SR2 in MS DOS Mode 3 Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s Web site and execute 3C90XCFG EXE 4 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 5 If changes are required save those changes and exit 6 Remove the 3Com cards driver diskette and restart the machine 7 Windows 95 SR2 should automatically recognize the 3COM 3C905 Ethernet card 8 With PCI Ethernet Controller listed click on Next 9 Click on Other Locations and insert the 3C905 driver s disk 1 of 2 10 Set the path to A and click on OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk1 11 3Com Etherlink XL TPO 10Mb Ethernet Adapter should now be listed Click on Finish
30. k 1 If you are using a Vectra VL8 go directly to step 7 If you are using a VLT follow the instructions below to complete the installation a Execute INSTALL EXE and set lines 1 5 as listed below e CANWCLIENT e YES e YES e C WINDOWS e NO e 3COM Etherlink XL Fast Etherlink XL Family Use driver provid ed on the 3Com driver s disk 1 b Highlight option 6 to continue with installation c When prompted insert the corresponding disks to complete file trans fer and driver installation d When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to re start the machine e After Windows loads open the NETWORK folder and double click the NETWORK SETUP icon f Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the follow ing network only g Click on OK twice and the installation is complete 7 Execute INST_DOS EXE and press enter to accept the agreement 905 bk ch_1 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Netware 3 12 server Windows for Workgroups 8 Accept the default installation options by pressing F10 9 At the Customize Support for Windows screen press F10 10 Select 32 bit LAN Drivers and hit the enter key 11 Page down the Board Drivers list to USER SPECIFIED 32 BIT DRIVER LIST and hit enter 12 Insert the 3COM Etherlink 3C905 Ethernet card and drivers
31. k XL PCI Busmaster NIC and click OK 17 With 3Com Fast Etherlink Etherlink XL PCI Busmaster NIC listed in the Network Adapters window click on Next 905 bk ch_8 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 18 Accept the default Network Protocol TCP IP and click on any additional protocols then click Next If you do not have the required Protocols information contact your network administrator 19 At the Network Services prompt accept default settings and click on Next 20 Finish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard preloaded HDD set the path to C I386 22 Insert the 3COM 3C905 drivers disk 2 into the floppy drive and hit Enter If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 23 After the files transfer from Disk 2 you will be prompted to provide the path to your NT files DO NOT follow this direction Ignore the request an set the path to A on disk 2 of 2 instead If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 DISK2 24 When the setup message 3Com dRMON SmartAgent appears click on OK 25 At the 3Com NIC Diagnostics v1 0 message click on
32. r path to A MSLANMAN DOS DRIVERS ETHERNET EL90X and click OK to complete file copying If you have an HP preloaded HDD set the path to C MASTERS DRIVERS LAN 3C905 DISK 1 MSLANMAN DOS DRIVERS ETHERNET EL90X 22 Finish the network card installation by clicking on OK in the Network Setup message 23 To complete the installation click on the Restart Computer button in the Windows Setup dialog box 905 bk ch_10 fb4 Page 1 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows 95 SR2 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Requirements e HP Vectra with Plug and Play enabled running Windows 95 SR2 e 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 e Vectra VL8 Driver Name OEMSETUP INF Size 49 3KB Date 12 1 97 e Vectra VLT Driver Name E190X SYS Size 45KB Date 3 21 97 e Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 IIOBaseAddress FCCOh PCI FC40h PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C905 adapter card into a PCI slot 2 Connect network cable media to the 3COM 3C905 card
33. te 12 20 96 e NDIS Driver Name E190X 386 Size 72KB Date 1 29 98 e Microsoft Windows NT Server 4 0 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 IIOBaseAddress FCCOh PCI FCCOh PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C905 adapter card into a PCI slot 905 bk ch_9 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows for Workgroups ver 3 11 2 Connect network cable media to the 3COM 3C905 card 3 Power on the machine and set Plug and Play in CMOS to off 4 After booting insert the 3COM s drivers disk Etherlink 3C905 Ethernet ver 4 3 and execute A 3C90XCFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3COM Drivers diskette and reboot the machine 8 After windows loads open the NETWORK program group and double click on Network Setup icon 9 Select the Networks button in the Network Setup dialog box 10 Click on the Install Microsoft Windows Network option and click
34. tion 16 Click OK to the Network dialog box to provide computer work group names 17 Specify your Computer Name Workgroup and Computer Description If you do not have the required information contact your network administrator 18 Click on the Configuration folder in the Network dialog box 19 Click on Add and then protocol from Select Network Component Type and click on Add 20 Pick Microsoft from the Manufacturers and TCP IP and then click OK 905 bk ch_10 fb4 Page 3 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 4 0 Windows 95 SR2 21 Highlight the TCP IP network component and click on the Properties button 22 If you know your TCP IP settings enter them in the TCP IP Properties dialog box otherwise leave the IP address choice checked Obtain an IP address automatically and click OK If you do not have the required information contact your network administrator 23 Click on Close and files will copy 24 Insert the Windows 95 CD ROM and click OK to the Insert Disk dialog box 25 When prompted enter the path for Windows 95 source files and click on OK in the Copying Files dialog box If you have an HP preloaded HDD set the path statement C MASTERS WIN9S5 SYSTEM CABS If you are using a Vectra VL8 go directly to 26 If you are using a Vectra
35. ts HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 File Name OEMSETUP INF Size 41KB Date 3 14 97 Windows 95 SR2 media If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Novell Netware 4 1 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Network Driver Optimization Normal e Full Duplex Disabled e Boot PROM Disabled e Media Type 10BASE T Vectra VL8 Vectra VL7 1 0 Base Address FC40h PCI FCCOh PCI Interrupt Request 11 PCI 9 PCI Level 905 bk ch_4 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Netware 4 1 server Windows 95 SR2 Procedure 1 With the HP Vectra turned off install the 3COM Etherlink HI 3C905 adapter card into a PCI slot Power on the machine and restart Windows 95 SR2 in MS DOS Mode Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s Web site and execute 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3Com cards driver diskette and restart the machine Windows 95 SR2 should automatically recognize the 3COM 3C905 Ethernet card With PCI Ethernet Controller listed click on Next Click on Other Locations and insert the 3C
36. unning Windows 95 SR2 e 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2 1 e Vectra VL8 File Name OEMSETUP INF Size 49 3KB Date 12 1 97 e Vectra VLT File Name E190X SYS Size 45KB Date 3 21 97 e Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e Media Type Auto Select N WAY Vectra VL8 Vectra VL7 I O Base Address FCCOh PCI FC4Oh PCI Interrupt Request 9 PCI 9 PCI Level Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C905 adapter card into a PCI slot 2 Connect network cable media to the 3COM 3C905 card 905 bk ch_6 fb4 Page 2 Thursday October 22 1998 9 51 AM Connecting to a Windows NT Server 3 51 Microsoft Windows 95 SR2 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM drivers disk 1 Etherlink 3C905 Ethernet Drivers Ver 2 1 and execute A 3C90XCFG EXE 5 Select Configure NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com software driver diskette and reboot the machine 8 When Windows 95 restarts a message will appear to indicate that new hardware has been found 9 Insert
37. xecute A 8C90XCFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 6 If changes are required save those changes and exit 7 Remove the 3Com card drivers diskette and reboot the machine 8 Power on the machine and allow it to boot to Windows NT Workstation 4 0 9 Log onto the machine with Administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel group and double click the Network icon 11 Click on the Yes button and agree to install Windows NT Networking 12 With Wired to the Network checked click on Next 13 Click the option to Select from list then on Have Disk 14 Insert the 3COM 3C905 drivers disk 1 into the floppy drive 15 Change the path to A for the Insert Disk dialog and click OK If you have a Hewlett Packard preloaded HDD set the path statement to C MASTERS LANDRV 3C905 Disk1 If you are using a Vectra VL7 follow the instructions below and then continue from step 18 If you are using a Vectra VL8 go directly to step 16 e Select 3Com Fast Etherlink XL Adapter 8C905 and click OK e With 3Com Fast Etherlink XL Adapter 8C905 listed in the Net work Adapters window click on Next 16 Select 3Com Fast Etherlink Etherlin
Download Pdf Manuals
Related Search