HP 3C509B-TP User's Manual
Contents
1. HEWLETT PACKARD Etherlink IIIB ISA Network Interface Card 10BT 3C509B TP Installation Guide Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation MMX is a trademark of Intel Corporation Pentium is a registered trademark of Intel Corporation Hewlett Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France 1998 Hewlett Packard Company Windows for Workgroups 1 Connecting to a Netware 3 12 Server Windows for Workgroups 1 Connecting to a Netware 3 12 Server Requirements HP Vectra with DOS an2. dialog box and then insert the 3COM 3C509 drivers disk 15 Click OK at the Install Driver dialog box If you have an HP preloaded HDD set path to C Masters LanDrv 3C509 16 Select 3Com Etherlink III 8C509 ISA Adapter in the Select OEM Option dialog box and click OK 17 Click on the OK button in the Bus Location dialog box 18 Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on Continue If you do not have the required information contact your network administrator 19 Choose to install all applicable TCP IP options and select Continue If you do not have the required information contact your network administrator 20 At the Network Settings dialog box click on OK 21 Accept the default NWLink IPX SPX Protocol Configuration and hit enter 22 At the TCP IP Configuration screen choose to use DHCP or enter your TCP information and click on OK If you do not have the required information contact your network 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 administrator 23 At the Domain Workgroup Settings Dialog Box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 24 To complete the installation remove the floppy disk and click on
3. 13 Accept the default settings press F10 to continue and verify the following entries for the Installation Configuration Summary O YES J CANOVELL CLIENTS32 O CNWINDOWS O 16 bit LAN drivers J 3Com Etherlink III Parallel Tasking Family 14 Press F10 to save and continue 15 When prompted insert the corresponding disks to complete file transfer and driver installation 16 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 17 After windows loads open the NETWORK folder double click the NETWORK SETUP icon 18 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only and click on OK 1 Connecting to a Netware 3 12 Server Windows for Workgroups Windows 95 SR2 1 Connecting to a Netware 3 12 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Vectra VL8 Driver Name W95EL5X9 INF Size 16KB Date 6 11 97 Vectra VL7 Driver Name Elnk VXD Size 30KB Date 7 18 96 Vectra VE7 VE8 Driver Name W95EL5X9 INF Size 16KB Date 6 11 97 Windows 95 SRZ media Novell Netrware 3 12 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 V
4. Elnk Vxd Size 30 2KB Date 7 18 96 Windows 95 media Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Connect network cable media to the 3COM 3C509B card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM drivers disk Etherlink 3C509 B Ethernet Drivers Ver 5 0 and change to Drive A and execute 3C5X9CFG EXE Select Configure NIC and verify the resource settings listed above 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 under the heading Device Configuration 6 Ifchanges are required save those changes and exit 7 Remove the 3Com Software driver diskette and reboot the machine 8 Click on Start and point to Settings then select the Control Panel 9 Inthe Control Panel group double click on the Network icon 10 In the Network dialog box click on the Add button 11 In the Select Network Componen
5. IP and hit enter 19 In the Network dialog box click on the Identification folder and specify your Computer Name Workgroup and Computer Description and click on OK If you do not have the required information contact your network administrator 20 Set the default configuration to the desired I O 300 and hit enter 21 When prompted specify the path to your Windows 95 files If you have an HP preloaded HDD set the path to 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 CAMASTERSWINSSNSYSTEMNCABSV 22 To complete the installation select Yes to restart your computer 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Windows NT Workstation Version 3 51 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 Requirements HP Vectra with Microsoft Windows NT Workstation 3 51 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name Elnk3 SYS Size 27KB Date 7 18 96 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210h 210h 300 Interrupt Request 10 10 10 Level Boot PROM Disabled Transceiver Type Auto Select Network Driver Optimization Windows or OS 2 Client Maximum Modem Speed 9600 Bps
6. In Windows NT Setup enter the path to your NT files and click on Continue If you have an HP preloaded HDD set path to C I386 12 Click on Do Not Detect from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 13 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 14 Set the path to A V in the Insert Disk dialog box and then insert the 3COM 3C509 drivers disk 15 Click OK at the Install Driver dialog box If you have an HP preloaded HDD set path to C Masters LanDrv 3C509 16 Select 3Com Etherlink III 8C509 ISA Adapter in the Select OEM Option dialog box and click OK 17 Click on the OK button in the Bus Location dialog box 18 Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on Continue If you do not have the required information contact your network administrator 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 19 Choose to install all applicable TCP IP options and select Continue If you do not have the required information contact your network administrator 20 At the Network Settings dialog box click on OK 21 Accept the default NWLink IPX SPX Protocol Configuration and hit e
7. Restart Computer button in the Windows NT Workstation Networking Setup dialog box 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 Windows NT Workstation 4 0 Requirements 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 HP Vectra with Windows NT Workstation 4 0 Service Pack 3 e 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name Elnk3 SYS Size 27KB Date 7 18 96 e Microsoft Windows NT Workstation 4 0 and service pack media If you have a Hewlett Packard pre loaded HDD the media is located at CAI386 e Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address Interrupt Request 10 Level e Boot PROM e Transceiver Type e Network Driver Optimization e Maximum Modem Speed e Plug and Play Compatibility e Full Duplex Procedure Disabled Auto Select Windows or OS 2 Client 9600 Baud Disabled Disabled 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot 2 Connect network media to the 3COM 3C509B card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM Etherlink 3C509 B Ethernet card and drivers disk ver 5 0 and execute A 3C5X9CFG EXE 5 Select C
8. for Workgroups Windows 95 SR2 2 Connecting to a Netware 4 11 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Vectra VL8 and VE7 VE8 Driver Name W95EL5XO9 INF Size 16KB Date 6 11 97 Vectra VL Driver Name Elnk VXD Size 30KB Date 7 18 96 Windows 95 SR2 media Novell Netrware 4 11 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Power on the machine and restart Windows 95 SR2 in MS DOS Mode Insert the 3COM drivers diskette ver 5 0 downloaded from 3COM s website and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit 2 Connecting to a Netware 4 11 Server Windows 95 SR2 6 Remove the 3com cards driver diskette and restart the machine 7 After windows loads click on Start to Sett
9. the path to your NT files and select Continue If you have a Hewlett Packard pre loaded HDD set the path to C I386 21 Accept type as ISA and number as 0 and click on OK 22 If you intend on using DHCP then click on Yes and skip the next step otherwise click on No If you do not have the required information contact your network administrator 23 Enter the required information IP Address Subnet Mask Default Gateway DNS and WINS information and click on OK 24 At the Show Bindings for window accept default entries and click Next 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 25 When Windows NT is now ready to start the network click on Next 26 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network administrator 21 After Network has been installed on this computer click on Finish 28 To complete the installation select Yes to reboot your computer 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Version Number 3Com 3c509 Rev 1
10. 11 After windows loads open the NETWORK Program Group and double click on Network Setup 8 Select the Networks button in the Network Setup dialog box 9 Click on the Install Microsoft Windows Network option and click OK 10 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 11 Click OK to accept the default choice of Unlisted or Updated Network Adapter 12 Type the path A WFW311 in the Install Driver dialog box and then insert the 3COM 3C509 drivers disk into the floppy drive and click OK If you have an HP preloaded HDD set path to C Masters LanDrv 3C509B WFW311 13 Select 3Com Etherlink III 8C5X9 in the Unlisted or Updated Network Adapter dialog box and click OK 14 Make sure that the 3Com Etherlink III 8C5X9 NDIS2 NDIS3 is selected in Network Drivers 15 Accept the applicable network protocols and then click on CLOSE e 3Com EtherLink III 8C5X9 NDIS2 NDIS3 e Microsoft NetBEUI e IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network ad ministrator 16 At the Network Setup dialog box click on OK 17 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK The Drivers will now start to copy 18 Finish the network card installation by
11. CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit 2 Connecting to a Netware 4 11 Server Windows for Workgroups 6 Remove the 3COM cards driver diskette and insert Netware client for DOS and MS Windows disk 1 If you are using a Vectra VL8 go straight to step 7 If you are using a VLT or VE7 VE8 finish the installation by using the instructions below Execute INSTSTALL EXE b Specify the settings as listed below e CANNWCLIENT Yes Yes e C WINDOWS No e 3Com Fast Etherlink Etherlink HI Bus Master for VE7 VE8 or 3COM Etherlink III Parallel Tasking Family for VL7 then highlight option 6 and then go to step e below c Under the heading Select the driver for your network board insert the 3Com 3C590 drivers disk and set the path to A NETWARE CLIENT If you have an HP preloaded HDD set path to C Masters LanDrv 3C509 NWCLIENT d Press Enter to continue the installation e When prompted insert the corresponding disks to complete file transfer and driver installation f When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine g After Windows loads open the NETWORK folder double click the NETWORK SETUP icon h Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows sup
12. E8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps e Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Power on the machine and restart Windows 95 SR2 in MS DOS Mode Insert the 3COM drivers diskette ver 5 0 downloaded from 3COM s website and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 1 Connecting to a Netware 3 12 Server Windows 95 SR2 5 Ifchanges are required save those changes and exit 6 Remove the 3com cards driver diskette and restart the machine 7 After windows loads click on Start to Settings and over to Control Panel 8 Double click on Network and select Add 9 Choose to add an adapter click on Add then on Have Disk 10 Insert the 3C509B drivers diskette and set path to A and hit enter If you have a Hewlett Packard pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B 11 High light the adapter labeled 3Com Etherlink III ISA 8C509 3C509B in ISA Mode and press OK 12 At the Network dialogue box click on the Identification folder 13 Enter your Computer Name Workgr
13. ONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 If changes are required save those changes and exit Remove the 3com cards driver diskette and reboot the machine Power on the machine and allow it to boot to Windows NT Workstation 4 0 c oo N o Log onto the machine with administrator privileges If you do not have the required information contact your network administrator 10 Open the Network Properties window and agree to install Windows NT Networking 11 With Wired to the Network checked click on Next 12 Click on the option to Select from list then on Have Disk 13 Insert the 3COM 3C509 drivers disk into the floppy drive 14 With the path set to A click OK If you have a Hewlett Packard pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B 15 Select 3Com Etherlink III 3C509 ISA Adapter and click OK 16 With 3Com Etherlink III 3509 ISA Adapter listed in the Network Adapters window click on Next 17 Accept the applicable network protocols and click on Next If you do not have the required information contact your network administrator 18 At the Network Services prompt accept default settings and click on Next 19 Finish the network card installation by clicking on Next 20 Designate
14. Plug and Play Compatibility Disabled Full Duple Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Connect network cable media to the 3COM 3C509B card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM Software 3C509 B Ethernet drivers disk ver 5 0 and execute A 8C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 7 Remove the 3com software driver diskette and reboot the machine 8 After windows loads open the Main program group double click on Control Panel icon 9 Double click on the Network icon and agree to install Windows NT Networking on your computer 10 Insert the Windows NT Workstation CD 11 In Windows NT Setup enter the path to your NT files and click on Continue If you have an HP preloaded HDD set path to C I386 12 Click on Do Not Detect from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 13 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 14 Set the path to A in the Insert Disk
15. Yes to reboot your computer 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 Windows for Workgroups Ver 3 11 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Ver 3 11 4 Connecting to a Windows NT Server 4 0 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name ElInk3 SYS Size 27KB Date 7 18 96 Microsoft Windows NT Server 4 0 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e O Base Address 300h e Interrupt Request Level 10 Boot PROM Disabled Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Connect network Cable Media to the 3COM 3C509B card After booting to DOS insert the 3COM s drivers disk Etherlink 3C509 B Ethernet ver 5 0 and execute A 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM Drivers diskette and reboot the machine 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Ver 3
16. ation dialog box Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on Continue If you do not have the required information contact your network administrator Choose to install all applicable TCP IP options and select Continue If you do not have the required information contact your network administrator At the Network Settings dialog box click on OK Accept the default NWLink IPX SPX Protocol Configuration and hit Enter 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 q Atthe TCP IP Configuration screen choose to use DHCP or enter your TCP information and click on OK If you do not have the required information contact your network administrator r Atthe Domain Workgroup Settings dialog box click on OK to ac cept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator s To complete the installation remove the floppy disk and click on Re start Computer button in the Windows NT Workstation Networking Setup dialog box 7 Remove the 3com software driver diskette and reboot the machine 8 After windows loads open the Main program group double click on Control Panel icon 9 Double click on the Network icon and agree to install Windows NT Networking on your computer 10 Insert the Windows NT Workstation CD 11
17. clicking on OK in the Network Setup message 19 To complete the installation click on Restart Computer button in the Windows Setup dialog box Windows 95 SR2 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 3COM Etherlink 3C509 B Ethernet card and drivers disk ver 5 0 Vectra VL8 and VE7 VE8 Driver Name W9b5EL5X9 INF Size 16KB Date 6 11 97 Vectra VL7 Driver Name Elnk3 vxd Size 30 2KB Date 7 18 96 DOS and MS Windows for Workgroups 3 11 media Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Connect network cable media to the 3COM 3C509B card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM drivers disk Etherlink 3C509 B Ethernet Drivers Ver 5 0 and change to Drive A and execute 3C5X9CFG EXE Select Configure NIC and verify the resource settings li
18. complete the installation select Yes to restart your computer 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Windows NT Workstation Version 3 51 Requirements 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 HP Vectra with Microsoft Windows NT Workstation 3 51 installed e 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name Elnk3 SYS Size 27KB Date 7 18 96 e Microsoft Windows NT Workstation 3 51 and Service Pack Media e Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210h 210h 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type e Network Driver Optimization e Maximum Modem Speed e Plug and Play Compatibility e Full Duplex Procedure Auto Select Windows or OS 2 Client 9600 Bps Disabled Disabled 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot 2 Connect network cable media to the 3COM 3C509B card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM Software 3C509 B Ethernet drivers disk ver 5 0 and execute A 3C5X9CFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Co
19. d MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 DOS ODI File Name 3C5X9 COM Size 42KB Date 7 21 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware server 3 12 that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware client for DOS and MS Windows Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Power on the machine and allow it to boot to a DOS prompt Insert the 3COM drivers diskette ver 5 0 downloaded from 3COM s website and execute 3C5X9CFG EXE 1 Connecting to a Netware 3 12 Server Windows for Workgroups 4 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 5 Ifchanges are required save those changes and exit 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS Windows disk 1 7 Execute INST_DOS EXE and enter yes to accept the agreement if you are using a Vectra VL8 then go directly to step 8 If you are using a Vect
20. ddress 300h e Interrupt Request Level 10 Boot PROM Disabled Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Connect network Cable Media to the 3COM 3C509B card After booting to DOS insert the 3COM s drivers disk Etherlink 3C509 B Ethernet ver 5 0 and execute A 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM Drivers diskette and reboot the machine 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 After windows loads open the NETWORK Program Group and double click on Network Setup 8 Select the Networks button in the Network Setup dialog box 9 Click on the Install Microsoft Windows Network option and click OK 10 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 11 Click OK to accept the default choice of Unlisted or Updated Network Adapter 12 Type the path A WFW311 in the Install Driver dialog box and then insert the 3COM 3C509 drivers disk into the floppy drive and click OK If you ha
21. ings and over to Control Panel 8 Double click on Network and select Add 9 Choose to add an adapter click on Add then on Have Disk 10 Insert the 3C509B drivers diskette and set path to A and hit enter If you have a Hewlett Packard pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B WIN95 11 High light the adapter labeled 3Com Etherlink III ISA 8C509 3C509B in ISA Mode and press OK 12 At the Network dialogue box click on the Identification folder 13 Enter your Computer Name Workgroup and Computer Description If you do not have a Computer name Workgroup name and Computer description contact your network administrator 14 Approve the Basic Configuration Resources by clicking on OK 15 When prompted set the path to your Windows 95 SR2 files and click on OK 16 Click on YES to complete installation and restart the machine Windows for Workgroups Ver 3 11 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 3 Connecting to a Windows NT Server 3 51 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name ElInk3 SYS Size 27KB Date 7 18 96 Microsoft Windows NT Server 3 51 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e O Base A
22. k III 3509 ISA Adapter listed in the Network Adapters window click on Next 17 Accept the applicable network protocols and click on Next If you do not have the required information contact your network administrator 18 At the Network Services prompt accept default settings and click on Next 19 Finish the network card installation by clicking on Next 20 Designate the path to your NT files and select Continue If you have a Hewlett Packard pre loaded HDD set the path to C I386 21 Accept type as ISA and number as 0 and click on OK 22 If you intend on using DHCP then click on Yes and skip the next step otherwise click on No If you do not have the required information contact your network administrator 23 Enter the required information IP Address Subnet Mask Default Gateway DNS and WINS information and click on OK 24 At the Show Bindings for window accept default entries and click Next 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 25 When Windows NT is now ready to start the network click on Next 26 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network administrator 21 After Network has been installed on this computer click on Finish 28 To complete the installation select
23. ndows or OS 2 Client 9600 Bps Disabled Disabled 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot 2 Connect network media to the 3COM 3C509B card 3 Insert a DOS bootable diskette and power on the machine 4 After booting insert the 3COM Etherlink 3C509 B Ethernet card and drivers disk ver 5 0 and execute A 3C5X9CFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 If changes are required save those changes and exit Remove the 3com cards driver diskette and reboot the machine Power on the machine and allow it to boot to Windows NT Workstation 4 0 c oo N o Log onto the machine with administrator privileges If you do not have the required information contact your network administrator 10 Open the Network Properties window and agree to install Windows NT Networking 11 With Wired to the Network checked click on Next 12 Click on the option to Select from list then on Have Disk 13 Insert the 3COM 3C509 drivers disk into the floppy drive 14 With the path set to A click OK If you have a Hewlett Packard pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B 15 Select 3Com Etherlink III 3C509 ISA Adapter and click OK 16 With 3Com Etherlin
24. nfiguration 6 Ifchanges are required save those changes and exit If you are using a Vectra VL8 or VL7 go directly to step 7 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 If you are using a Vectra VE7 VE8 follow the instructions below to complete the installation a b C If changes are required save those changes and exit Remove the 3COM software driver diskette and reboot the machine After Windows loads open the Main program group double click on Control Panel icon Double click on the Network icon and agree to install Windows NT Networking on your computer Insert the Windows NT Workstation CD In Windows NT Setup enter the path to your NT files and click on Continue If you have an HP preloaded HDD set path to C I386 Click on Do Not Detect from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue Set the path to A in the Insert Disk dialog box and then insert the 3COM 3C509 drivers disk Click OK at the Install Driver dialog box If you have an HP pre loaded HDD set path to C Masters LanDrv 3C509 Select 3Com Etherlink III 8C509 ISA Adapter in the Select OEM Option dialog box and click OK Click on the OK button in the Bus Loc
25. nter 22 At the TCP IP Configuration screen choose to use DHCP or enter your TCP information and click on OK If you do not have the required information contact your network administrator 23 At the Domain Workgroup Settings Dialog Box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 24 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box Windows NT Workstation 4 0 Requirements 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 HP Vectra with Windows NT Workstation 4 0 Service Pack 3 e 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 Driver Name Elnk3 SYS Size 27KB Date 7 18 96 e Microsoft Windows NT Workstation 4 0 and service pack media If you have a Hewlett Packard pre loaded HDD the media is located at CAI386 e Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration Vectra VL8 Vectra VL7 Vectra VE7 VE8 1 0 Base Address 210 210 300 Interrupt Request 10 10 10 Level e Boot PROM Disabled e Transceiver Type e Network Driver Optimization e Maximum Modem Speed e Plug and Play Compatibility e Full Duplex Procedure Auto Select Wi
26. oup and Computer Description If you do not have a Computer name Workgroup name and Computer description contact your network administrator 14 Approve the Basic Configuration Resources by clicking on OK 15 When prompted set the path to your Windows 95 SR2 files and click on OK 16 Click on YES to complete installation and restart the machine Windows for Workgroups 2 Connecting to a Netware 4 11 Server Windows for Workgroups 2 Connecting to a Netware 4 11 Server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C509 B ethernet card and drivers disk ver 5 0 DOS ODI File Name 3C5X9 COM Size 42KB Date 7 21 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware server 4 11 that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware client for DOS and MS Windows Device Configuration e O Base Address 300 e Interrupt Request Level 10 Boot PROM Disabled e Transceiver Type Auto Select e Network Driver Optimization Windows or OS 2 Client e Maximum Modem Speed 9600 Bps e Plug and Play Compatibility Disabled e Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509 B adapter card into an ISA slot Power on the machine and allow it to boot to a DOS prompt Insert the 3COM drivers diskette ver 5 0 downloaded from 3COM s website and execute 3C5X9
27. port for the follow ing network only and click on OK 7 Execute INST DOS EXE and enter yes to accept the agreement 8 Accept the default products by pressing enter and then press F10 to continue 9 Select 16 bit LAN Drivers and hit the enter key 2 Connecting to a Netware 4 11 Server Windows for Workgroups 10 Page down the Board Drivers list to USER SPECIFIED 16 BIT DRIVER and hit enter 11 Insert the 3COM Etherlink 3509 Ethernet card and drivers disk set the path to ANNWCLIENTN and press enter 12 Select 3Com Etherlink III Parallel Tasking Family and press enter 13 Accept the default settings press F10 to continue and verify the following entries for the Installation Configuration Summary O YES J CANOVELL CLIENTS32 O CNWINDOWS O 16 bit LAN drivers J 3Com Etherlink III Parallel Tasking Family 14 Press F10 to save and continue 15 When prompted insert the corresponding disks to complete file transfer and driver installation 16 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 17 After windows loads open the NETWORK folder double click the NETWORK SETUP icon 18 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only and click on OK 2 Connecting to a Netware 4 11 Server Windows
28. ra VL7 or VE7 VE8 complete the installation by following the steps below A Specify the settings as listed below e CANWCLIENT Yes Yes e CNWINDOWS No e 3Com Fast Etherlink Etherlink III Bus Master2 b Under the heading Select the driver for your network board insert the 3Com 3C590 drivers disk and set the path to A NETWARE CLI ENT If you have an HP preloaded HDD set path to C Masters Lan Drv 3C509 NWCLIENT Press Enter to continue the installation d When prompted insert the corresponding disks to complete file transfer and driver installation e When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine f After Windows loads open the NETWORK folder double click the NETWORK SETUP icon g Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only and click on OK 8 Accept the default products by pressing enter and then press F10 to continue 1 Connecting to a Netware 3 12 Server Windows for Workgroups 9 Select 16 bit LAN Drivers and hit the enter key 10 Page down the Board Drivers list to USER SPECIFIED 16 BIT DRIVER and hit enter 11 Insert the 3COM Etherlink 3509 Ethernet card and drivers disk set the path to A NWCLIENT and press enter 12 Select 3Com Etherlink III Parallel Tasking Family and press enter
29. sted above under the heading Device Configuration 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 6 Ifchanges are required save those changes and exit 7 Remove the 3Com Software driver diskette and reboot the machine 8 Click on Start and point to Settings then select the Control Panel 9 Inthe Control Panel group double click on the Network icon 10 In the Network dialog box click on the Add button 11 In the Select Network Component Type dialog box highlight Adapter then click on Add 12 Click on Have Disk in the Select Network adapters dialog box 13 Insert the 3COM Software Etherlink 3C509 B Ethernet Drivers Ver 5 0 disk into the floppy drive 14 With the Path set to A V in the Install From Disk dialog box click OK If you have an HP pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B 15 Select the 3Com Etherlink II ISA 8C509 3C509B in ISA mode and click OK 16 Accept the default Network Protocols as seen below and click on OK If you do not have the required information contact your network administrator O Client for NetWare Networks O 3Com EtherLink III ISA 3C509 3C509b O IPX SPX compatible Protocol NetBEUI 17 In the configuration folder click on Add then click Protocol and hit enter 18 Under Manufacturers high light Microsoft and under Network Protocols high light TCP
30. t Type dialog box highlight Adapter then click on Add 12 Click on Have Disk in the Select Network adapters dialog box 13 Insert the 3COM Software Etherlink 3C509 B Ethernet Drivers Ver 5 0 disk into the floppy drive 14 With the Path set to A V in the Install From Disk dialog box click OK If you have an HP pre loaded HDD set the path statement to C MASTERS LANDRV 3C509B 15 Select the 3Com Etherlink III ISA 8C509 3C509B in ISA mode and click OK 16 Accept the default Network Protocols as seen below and click on OK If you do not have the required information contact your network administrator Client for NetWare Networks e 3Com EtherLink III ISA 3C509 3C509b e PX SPX compatible ProtocolNetBEUI 17 In the configuration folder click on Add then click Protocol and hit enter 18 Under Manufacturers high light Microsoft and under Network Protocols high light TCP IP and hit enter 19 In the Network dialog box click on the Identification folder and specify your Computer Name Workgroup and Computer Description and click on OK If you do not have the required information contact your network administrator 20 When prompted specify the path to your Windows 95 files If you have 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 an HP preloaded HDD set the path to C MASTERS WIN9QS SYSTEM CABS 21 To
31. ve an HP preloaded HDD set path to C Masters LanDrv 3C509B WF W311 13 Select 3Com Etherlink III 8C5X9 in the Unlisted or Updated Network Adapter dialog box and click OK 14 Make sure that the 3Com Etherlink III 8C5X9 NDIS2 NDIS3 is selected in Network Drivers 15 Accept the applicable network protocols and then click on CLOSE e 3Com EtherLink III 8C5X9 NDIS2 NDIS3 e Microsoft NetBEUI e IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network ad ministrator 16 At the Network Setup dialog box click on OK 17 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK The Drivers will now start to copy 18 Finish the network card installation by clicking on OK in the Network Setup message 19 To complete the installation click on Restart Computer button in the Windows Setup dialog box 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Ver 3 11 Windows 95 SR2 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 3COM Etherlink 3C509 B Ethernet card and drivers disk ver 5 0 Vectra VL8 and VE7 VE8 Driver Name W95EL5X9 INF Size 16KB Date 6 11 97 Vectra VL7 Driver Name
Download Pdf Manuals
Related Search