Home

HP 3C509B ISA User's Manual

1. Procedure 1 With the HP Vectra turned off install the 3C0M 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3C0M 3C509 driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration a A W N If changes are required save those changes and exit 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 8 Installing the 3COM EtherLink IIl 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 4 11 Server 8 Log onto Windows NT4 Workstation with administrator privileges Contact your network administrator if you do not have the required information 9 Right click on the Network Neighborhood icon and select Properties 10 Click on Yes when prompted to install Windows NT Networking 11 Select Wired to the network and click on Next 12 Click on the Select from list button and then the Have Disk button 13 Insert the 3COM 3C509B driver disk in the floppy drive 14 Set the path to A in the dialog box and click on OK 15 Choose by highlighting the 3Com EtherLink 8c509 ISA Adapter and click on OK 16 With 3Com EtherLink 3c509 ISA Adapter listed in the Network Adapters window click on
2. Next 17 Select the applicable network protocols and click on Next Contact your network administrator if you do not have the required information 18 At the Network Services prompt accept default settings and click on Next 19 Click on Next to continue the network card installation 20 Set the path to D I1386 D represents the CD ROM drive with the Windows NT4 Workstation CD in the dialog box and click on Continue 21 Select ISA for the BUS Type and click on OK 22 The 3COM Installation Wizard will start This wizard configures the network adapter Select Custom Installation and click on Next Set adapter resources according to values noted above and click on Next Perform NIC Test and click on Next if the adapter is operating correctly Perform Network Connection Test and click on Next if connectivity is verified Do not configure Dynamic Access feature and click on Next Do not save setting for a future NIC installation and click on Next Click on Finish to complete the installation 23 Set the path to A in the dialog box and click on Continue 24 At the Show Bindings for prompt accept the default settings and click on Next 25 Click on Next to start the network 8 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 4 11 Server 26 Specify your Computer Name
3. Workgroup or Domain Contact your network administrator if you do not have the required information and click on Next 27 Click on Finish to complete the installation 28 Remove the 3Com driver disk from the floppy drive and select Yes at the prompt to shut down and restart your computer for the new settings to take effect 29 Log onto Windows NT4 Workstation with administrator privileges 30 From the location of the Novell IntranetWare Client v 4 11b installation files execute Setupnw exe 31 Click on Continue to continue with the Novell IntranetWare Client installation 32 Click on Yes to agree to the Software License Agreement to begin installation 33 Click on the Reboot button at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect 34 Click on the IntranetWare tab of the Novell IntranetWare Client Services Login screen 35 Select NDS Login and specify the Preferred Server Name Contact your network administrator if you do not have the required information 36 Click on the Login tab and specify your Name and Password to login 37 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer 38 Install the Hewlett Packard Soft Power Down application once the Service Pack 4 has been installed 9 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter
4. Error enumerating cards The NIC specific DLL TCAUM509 did not find any NICs present 16 Click on YES to restart the system when prompted 17 From the location of the Novell Client for Windows 95 v 2 5 installation files execute Setup exe 18 Click on Yes to accept the License Agreement 19 Select Custom installation and click on Next 20 Select NDS NetWare 4 x or higher and click on Next 21 Click on Install to start the installation 22 Click on Yes to set the Preferred Tree Server etc If you do not have the required information contact your network administrator 23 Click on Reboot to complete the installation 24 Right click on the Network Neighborhood icon and select Properties 25 Accept the default Network Protocols and the Primary Network Logon to Novell NetWare Client as seen below and click on OK If you do not have the required information contact your network administrator 4 Installing the 3COM EtherLink IIl 3C509B ISA 10BT Network Adapter Connecting to a NetWare 4 11 Server 26 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus Master PCI Ethernet Adapter IPX 32 bit Protocol for the Novell NetWare Client IPX SPX compatible Protocol NetBEUI 27 When prompted specify the path to your Windows 95 files 28 Click on Yes when prompted to restart the system 5 Installing the 3COM EtherLink III 3C509B I
5. Microsoft Windows NT 3 51 Workstation 9 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 3 51 Workstation Connecting to a Requirements Windows NT 3 51 Server e HP Vectra with Windows NT 3 51 Workstation e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND3 SYS version 5 26 31 e Microsoft Windows NT 3 51 Workstation media e Microsoft Windows NT 3 51 Service Pack 5 e Microsoft Windows NT 3 51 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 10 05 05 I O Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3C0M 3C509B driver disk and execute 8C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration UO OD N If changes are required save those changes and exit 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 9 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 3 51 Server 8 Log onto Windows NT3 51 Workstat
6. Remove the 3COM 3C509B driver disk and reboot the system to Windows 95SR2 5 10 Windows 95SR2 5 will automatically recognize the 3COM 3C509B network adapter as 8Com 3C509B EtherLink II 11 Insert the 3COM 3C509B driver disk in the floppy drive and click on Next from the Update Device Driver Wizard dialog box 12 When Windows 95 detects the updated driver 3Com EtherLink II ISA 3C509b TP in PnP mode click on Finish 13 During the Update Device Driver process point to the appropriate file locations i e drivers disk or Windows 95 CD to install the necessary files Keep newer files when a file being copied is older than the file currently on your computer 14 Click on OK when the system prompts for the computer and workgroup names 15 Enter the Computer Name Workgroup and Computer Description in the appropriate spaces and click on Close Contact your network administrator if you do not have the required information According to 83COM click on OK to ignore the error message indicating Error enumerating cards The NIC specific DLL TCAUM509 did not find any NICs present 16 Click on YES to restart the system when prompted 17 Right click on the Network Neighborhood icon and select Properties 18 Accept the default Network Protocols and the Primary Network Logon Client for Microsoft Networks as seen below and click on OK If you do not have the required in
7. dialog box and then insert the 3COM driver disk in the floppy drive and click OK 16 Select 3COM Etherlink 3c509 ISA Adapter in the Select OEM Option dialog box and click OK 17 Select ISA for the BUS Type and click on OK 18 Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on the Continue button Contact your network administrator if you do not have the required information 19 Press OK to continue form Network Settings dialog box 20 If applicable press OK to continue form NWLink IPX SPX Protocol Configuration dialog box 21 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name 22 To complete the installation remove the floppy disk and click on Restart computer in the Windows NT Workstation Networking Setup dialog box 23 Install the Windows NT3 51 Service Pack 5 application 11 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Microsoft Windows NT 3 51 Workstation 11 Installing the 3COM EtherLink II 3C509B ISA 10BT Network Adapter Microsoft Windows NT 3 51 Workstation Connecting to a Novell Requirements NetWare 4 11 Server HP Vectra with Windows NT 3 51 Workstation e 3COM EtherLink III 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND3 SYS
8. from the NetWare Tools folder to login to a server If you do not have the required information contact your network administrator
9. gt to boot to Windows 95 command prompt Insert the 3COM 3C509B driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 8 If changes are required save those changes and exit NOTE 4 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Connecting to a NetWare 4 11 Server 9 Remove the 3COM 3C509B driver disk and reboot the system to Windows 95SR2 5 10 Windows 95SR2 5 will automatically recognize the 3COM 3C509B network adapter as 8Com 3C509B EtherLink II 11 Insert the 3COM 3C509B driver disk in the floppy drive and click on Next from the Update Device Driver Wizard dialog box 12 When Windows 95 detects the updated driver 3Com EtherLink II ISA 3C509b TP in PnP mode click on Finish 13 During the Update Device Driver process point to the appropriate file locations i e drivers disk or Windows 95 CD to install the necessary files Keep newer files when a file being copied is older than the file currently on your computer 14 Click on OK when the system prompts for the computer and workgroup names 15 Enter the Computer Name Workgroup and Computer Description in the appropriate spaces and click on Close Contact your network administrator if you do not have the required information According to 83COM click on OK to ignore the error message indicating
10. version 5 26 31 e Microsoft Windows NT 3 51 Workstation media e Microsoft Windows NT 3 51 Service Pack 5 e Novell NetWare 4 11 Server system that supports IPX network protocol e Novell IntranetWare Client for Windows NT v4 11b installation media Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 10 05 05 1 0 Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3C0M 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3C0M 3C509 driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration a A W N If changes are required save those changes and exit 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 11 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 4 11 Server 8 Log onto Windows NT3 51 Workstation with administrator privileges Contact your network administrator if you do not have the required information 9 Open the Network icon in the Control Panel program group 10 Click on YES in the Network Settings dialog box to install Windows NT Networking 11 Insert the Windows NT 3 51Workstation CD in the CD ROM drive 1
11. 09B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3COM 3C509 driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration a Fe W N If changes are required save those changes and exit Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 10 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 4 0 Server 8 Log onto Windows NT3 51 Workstation with administrator privileges Contact your network administrator if you do not have the required information 9 Open the Network icon in the Control Panel program group 10 Click on YES in the Network Settings dialog box to install Windows NT Networking 11 Insert the Windows NT 3 51Workstation CD in the CD ROM drive 12 Set the path to D 1386 D represents the CD ROM drive with the Windows NT 3 51 CD in the dialog box of the Windows NT Setup window and click on Continue 13 Click on the Do Not Detect button from the Network Adapter Card Detection window and click on the Continue button in the following Network Adapter Card Detection window 14 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 15 Set the path to A in the Insert Disk
12. 2 Set the path to D 1386 D represents the CD ROM drive with the Windows NT 3 51 CD in the dialog box of the Windows NT Setup window and click on Continue 13 Click on the Do Not Detect button from the Network Adapter Card Detection window and click on the Continue button in the following Network Adapter Card Detection window 14 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 15 Set the path to A in the Insert Disk dialog box and then insert the 3COM driver disk in the floppy drive and click OK 16 Select 3COM Etherlink 8c509 ISA Adapter in the Select OEM Option dialog box Click OK 17 Select ISA for the BUS Type and click on OK 18 Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on the Continue button Contact your network administrator if you do not have the required information 19 Press OK to continue form Network Settings dialog box 20 If applicable press OK to continue from NWLink IPX SPX Protocol Configuration dialog box 21 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name 22 To complete the installation remove the floppy disk and click on Restart computer in
13. A 10BT Network Adapter Microsoft Windows 95 R2 5 1 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 SR2 5 Connecting to a Requirements Windows NT 3 51 Server tp Vectra with Windows 95 SR2 5 e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND3 SYS version 5 26 31 e Microsoft Windows 95 SR2 5 media e Microsoft Windows NT 3 51 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 5 03 07 1 0 Address 210 210 210 Procedure 1 Power on the system and start Windows 95SR2 5 2 From the 3COM 8C509B driver disk run PREINSTL EXE 3 Shutdown and power down the system With the HP Vectra turned off install the 3C0M 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the system and press SHIFT lt F5 gt to boot to Windows 95 command prompt Insert the 3COM 3C509B driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 8 If changes are required save those changes and exit NOTE 1 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 3 51 Server 9
14. Contact your network administrator if you do not have the required information 9 Right click on the Network Neighborhood icon and select Properties 10 Click on Yes when prompted to install Windows NT Networking 11 Select Wired to the network and click on Next 12 Click on the Select from list button and then the Have Disk button 13 Insert the 3COM 3C509B driver disk in the floppy drive 14 Set the path to A in the dialog box and click on OK 15 Choose by highlighting the 3Com EtherLink 8c509 ISA Adapter and click on OK 16 With 3Com EtherLink 3c509 ISA Adapter listed in the Network Adapters window click on Next 17 Select the applicable network protocols and click on Next Contact your network administrator if you do not have the required information 18 At the Network Services prompt accept default settings and click on Next 19 Click on Next to continue the network card installation 20 Set the path to D I1386 D represents the CD ROM drive with the Windows NT4 Workstation CD in the dialog box and click on Continue 21 Select ISA for the BUS Type and click on OK 22 The 3COM Installation Wizard will start This wizard configures the network adapter Select Custom Installation and click on Next Set adapter resources according to values noted above and click on Next Per
15. EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a NetWare 3 12 Server 26 Novell NetWare Client Novell NetWare Client 3COM Etherlink III Bus Master PCI Ethernet Adapter IPX 32 bit Protocol for the Novell NetWare Client IPX SPX compatible Protocol NetBEUI 27 When prompted specify the path to your Windows 95 files 28 Click on Yes when prompted to restart the system 4 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Microsoft Windows 95 R2 5 4 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 SR2 5 Connecting toaNetWare Requirements Sl LDANEI e HP Vectra with Windows 95 SR2 5 e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and drivers disk version 6 0 e Driver File ELNK8ND8 SYS version 5 26 31 e Microsoft Windows 95 SR2 5 media e Novell NetWare 4 11 Server that supports IPX network protocol e Novell Client for Windows 95 v2 5 installation media Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 03 07 1 0 Address 210 210 210 Procedure 1 Poweron the system and start Windows 95SR2 5 2 From the 3COM 8C509B driver disk run PREINSTL EXE 3 Shutdown and power down the system With the HP Vectra turned off install the 3COM 38C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the system and press SHIFT lt F5
16. LA packarD 3COM Etherlink III 3C509B ISA 10BT Network Adapter Installation Guide Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation MMX is a trademark of Intel Corporation Pentium is a registered trademark of Intel Corporation Hewlett Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France 1999 Hewlett Packard Company General information to read before installing General information to read before installing e Onallsystems Before installing LAN card go into Bios setup and set PnP OS field to NO e H
17. SA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation 5 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation Connecting to a Requirements Windows NT 3 51 Server e HP Vectra with Windows NT 4 0 Workstation e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND4 SYS version 5 26 40 e Microsoft Windows NT 4 0 Workstation media e Microsoft Windows NT 4 0 Service Pack 4 media e Microsoft Windows NT 3 51 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 5 5 5 I O Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3C0M 3C509B driver disk and execute 8C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration UO OD N If changes are required save those changes and exit 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 5 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 3 51 Server 8 Log onto W
18. e Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 5 03 07 1 0 Address 210 210 210 Procedure 1 Poweron the system and start Windows 95SR2 5 2 From the 3COM 8C509B driver disk run PREINSTL EXE 3 Shutdown and power down the system With the HP Vectra turned off install the 3COM 38C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the system and press SHIFT lt F5 gt to boot to Windows 95 command prompt Insert the 3COM 3C509B driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration 8 If changes are required save those changes and exit NOTE 3 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a NetWare 3 12 Server 9 Remove the 3COM 3C509B driver disk and reboot the system to Windows 95SR2 5 10 Windows 95SR2 5 will automatically recognize the 3COM 3C509B network adapter as 8Com 3C509B EtherLink II 11 Insert the 3COM 3C509B driver disk in the floppy drive and click on Next from the Update Device Driver Wizard dialog box 12 When Windows 95 detects the updated driver 3Com EtherLink II ISA 3C509b TP in PnP mode click on Finish 13 During the Update Device Driver process point to the appropriate file locations i e drivers disk or Windows 95 CD to install the necessary files Kee
19. e system and press SHIFT lt F5 gt to boot to Windows 95 command prompt Insert the 3COM 3C509B driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM 3C509B driver disk and reboot the system to Windows 95SR2 5 2 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 4 0 Server 10 Windows 95SR2 5 will automatically recognize the 3COM 3C509B network adapter as 8Com 3C509B EtherLink II 11 Insert the 3COM 3C509B driver disk in the floppy drive and click on Next from the Update Device Driver Wizard dialog box 12 When Windows 95 detects the updated driver 3Com EtherLink HI ISA 3C509b TP in PnP mode click on Finish 13 During the Update Device Driver process point to the appropriate file locations i e drivers disk or Windows 95 CD to install the necessary files Keep newer files when a file being copied is older than the file currently on your computer 14 Click on OK when the system prompts for the computer and workgroup names 15 Enter the Computer Name Workgroup and Computer Description in the appropriate spaces and click on Close Contact your network administrator if you do not have the required information 16 Note According to 3COM click on OK to igno
20. e the required information 16 At the Network Setup dialog box click on OK 17 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK Contact your network administrator if you do not have the required information 18 At the Network Setup dialog box click on OK 19 To complete the installation remove the 3COM 3C509B driver disk from the floppy drive and click on Restart Computer button in the Windows Setup dialog box 13 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows for Workgroups 3 11 13 Installing the 3COM EtherLink II 3C509B ISA 10BT Network Adapter Microsoft Windows for Workgroups 3 11 Connecting to a Novell Requirements NetWare 4 11 Server HP Vectra with DOS and MS Windows for Workgroups 3 11 e 3COM EtherLink III 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File 3C5X9 COM version 2 05 e Microsoft Windows for Workgroups 3 11 media e Novell NetWare 4 11 Server system that supports IPX network protocol e NetWare Client for DOS and MS Windows v1 21 installation media Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 05 05 I O Address 210 300 300 Procedure 1 With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot 2 Connect network cable med
21. f install the 3C0M 3C509B network adapter into an ISA slot 2 Connect network cable media to the 3COM 3C509B network adapter 3 Power on the system and boot to MS DOS 4 Insert the 3COM 3C509 driver disk and execute 3C5X9CFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM 3C509B driver disk and restart the system 8 After Windows loads open the NETWORK Program Group and double click on Network Setup 9 Click on the Networks button in the Network Setup dialog box 12 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 4 0 Server 10 Click on the Install Microsoft Windows Network option and click OK 11 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 12 Click OK to accept the default choice of Unlisted or Updated Network Adapter 13 Type the path A WFW311 in the Install Driver dialog box and then insert the 3COM 3C509B driver disk into the floppy drive and click OK 14 Select 8COM EtherLink II 8C5X9 in the Unlisted or Updated Network Adapter dialog box and click OK 15 Accept the applicable network protocols and then click on CLOSE Contact your network administrator if you do not hav
22. form NIC Test and click on Next if the adapter is operating correctly Perform Network Connection Test and click on Next if connectivity is verified Do not configure Dynamic Access feature and click on Next Do not save setting for a future NIC installation and click on Next Click on Finish to complete the installation 23 Set the path to A in the dialog box and click on Continue 24 At the Show Bindings for prompt accept the default settings and click on Next 25 Click on Next to start the network 7 Installing the 3COM EtherLink IlI 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 3 12 Server 26 Specify your Computer Name Workgroup or Domain Contact your network administrator if you do not have the required information and click on Next 27 Click on Finish to complete the installation 28 Remove the 3Com driver disk from the floppy drive and select Yes at the prompt to shut down and restart your computer for the new settings to take effect 29 Log onto Windows NT4 Workstation with administrator privileges 30 From the location of the Novell IntranetWare Client v 4 11b installation files execute Setupnw exe 31 Click on Continue to continue with the Novell IntranetWare Client installation 32 Click on Yes to agree to the Software License Agreement to begin installation 33 Click on the Reboot but
23. formation contact your network administrator 19 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink II ISA 3C509b TPO in PnP mode 3Com TCAATDI Diagnostic TDI IPX SPX compatible Protocol NetBEUI 20 Click on OK to accept the configuration 21 When prompted specify the path to your Windows 95 files 22 Click on Yes when prompted to restart the system 2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 R2 5 2 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 SR2 5 Connecting to a Requirements Windows NT 4 0 Server HP Vectra with Windows 95 SR2 5 e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and drivers disk version 6 0 e Driver File ELNK8ND8 SYS version 5 26 31 e Microsoft Windows 95 SR2 5 media e Microsoft Windows NT 4 0 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols e Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 03 07 I O Address 210 210 210 Procedure 1 Poweron the system and start Windows 95SR2 5 2 From the 3COM 8C509B driver disk run PREINSTL EXE 3 Shutdown and power down the system With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on th
24. ia to the 3COM 3C509B network adapter 3 Power on the system and boot to MS DOS 4 Insert the 3COM 3C509 driver disk and execute 3C5X9CFG EXE 5 Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM 3C509B driver disk and restart the system From the location of the NetWare Client for DOS and Windows v1 21 installation files execute Install exe 13 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 4 11 Server 9 Select option 5 Select the driver for your network board and press Enter 10 Select OTHER DRIVERS from the Network Board selection 11 Insert the 3COM 3C509B driver disk into the floppy drive 12 Type the path A NWCLIENT when prompted and press Enter 13 Select 8Com EtherLink II Parallel Tasking Family and hit Enter 14 Accept the default network board settings and press F10 to save it 15 Select option 6 Highlight here and press lt Enter gt to install and press Enter to begin installation 16 When the installation is finished remove the 3COM 3C509B driver disk from the floppy drive and press lt CTR gt lt ALT gt lt DEL gt to restart the system 17 You may login to a server from the DOS prompt or load Windows for Workgroup v3 11 and use the NetWare User Tools
25. icrosoft Windows NT 4 0 Workstation 6 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation Connecting to a Requirements Windows NT 4 0 Server HP Vectra with Windows NT 4 0 Workstation e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND4 SYS version 5 26 40 e Microsoft Windows NT 4 0 Workstation media e Microsoft Windows NT 4 0 Service Pack 4 media e Microsoft Windows NT 4 0 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 05 05 I O Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3COM 3C509 driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration a Fe W N If changes are required save those changes and exit Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 6 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 4 0 Server 8 Log onto Windows NT4 Workstation with admin
26. indows NT4 Workstation with administrator privileges Contact your network administrator if you do not have the required information 9 Right click on the Network Neighborhood icon and select Properties 10 Click on Yes when prompted to install Windows NT Networking 11 Select Wired to the network and click on Next 12 Click on the Select from list button and then the Have Disk button 13 Insert the 3COM 3C509B driver disk in the floppy drive 14 Set the path to A in the dialog box and click on OK 15 Choose by highlighting the 3Com EtherLink 8c509 ISA Adapter and click on OK 16 With 3Com EtherLink 3c509 ISA Adapter listed in the Network Adapters window click on Next 17 Select the applicable network protocols and click on Next Contact your network administrator if you do not have the required information 18 At the Network Services prompt accept default settings and click on Next 19 Click on Next to continue the network card installation 20 Set the path to D I1386 D represents the CD ROM drive with the Windows NT4 Workstation CD in the dialog box and click on Continue 21 Select ISA for the BUS Type and click on OK 22 The 3COM Installation Wizard will start This wizard configures the network adapter Select Custom Installation and click on Next Set adapter resources accordi
27. ion with administrator privileges Contact your network administrator if you do not have the required information 9 Open the Network icon in the Control Panel program group 10 Click on YES in the Network Settings dialog box to install Windows NT Networking 11 Insert the Windows NT 3 51Workstation CD in the CD ROM drive 12 Set the path to D 1386 D represents the CD ROM drive with the Windows NT 3 51 CD in the dialog box of the Windows NT Setup window and click on Continue 13 Click on the Do Not Detect button from the Network Adapter Card Detection window and click on the Continue button in the following Network Adapter Card Detection window 14 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 15 Set the path to A in the Insert Disk dialog box and then insert the 3COM driver disk in the floppy drive and click OK 16 Select 3COM Etherlink 3c509 ISA Adapter in the Select OEM Option dialog box and click OK 17 Select ISA for the BUS Type and click on OK 18 Choose the appropriate network protocols by clicking the check boxes in the Windows NT Setup dialog box and click on the Continue button Contact your network administrator if you do not have the required information 19 Press OK to continue from Network Se
28. istrator privileges Contact your network administrator if you do not have the required information 9 Right click on the Network Neighborhood icon and select Properties 10 Click on Yes when prompted to install Windows NT Networking 11 Select Wired to the network and click on Next 12 Click on the Select from list button and then the Have Disk button 13 Insert the 3COM 3C509B driver disk in the floppy drive 14 Set the path to A in the dialog box and click on OK 15 Choose by highlighting the 3Com EtherLink 8c509 ISA Adapter and click on OK 16 With 3Com EtherLink 3c509 ISA Adapter listed in the Network Adapters window click on Next 17 Select the applicable network protocols and click on Next Contact your network administrator if you do not have the required information 18 At the Network Services prompt accept default settings and click on Next 19 Click on Next to continue the network card installation 20 Set the path to D I1386 D represents the CD ROM drive with the Windows NT4 Workstation CD in the dialog box and click on Continue 21 Select ISA for the BUS Type and click on OK 22 The 3COM Installation Wizard will start This wizard configures the network adapter Select Custom Installation and click on Next Set adapter resources according to values noted above and clic
29. k on Next Perform NIC Test and click on Next if the adapter is operating correctly Perform Network Connection Test and click on Next if connectivity is verified Do not configure Dynamic Access feature and click on Next Do not save setting for a future NIC installation and click on Next Click on Finish to complete the installation 23 Set the path to A in the dialog box and click on Continue 24 At the Show Bindings for prompt accept the default settings and click on Next 25 Click on Next to start the network 6 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 4 0 Server 26 Specify your Computer Name Workgroup or Domain Contact your network administrator if you do not have the required information and click on Next 27 Click on Finish to complete the installation 28 Remove the 3Com driver disk from the floppy drive and select Yes at the prompt to shut down and restart your computer for the new settings to take effect 29 Log onto Windows NT4 Workstation with administrator privileges 30 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer 31 Install the Hewlett Packard Soft Power Down application once the Service Pack 4 has been installed 7 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstatio
30. n 7 Installing the 3COM EtherLink II 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation Connecting to a Novell Requirements NetWare 3 12 Server HP Vectra with Windows NT 4 0 Workstation e 3COM EtherLink III 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND4 SYS version 5 26 40 e Microsoft Windows NT 4 0 Workstation media e Microsoft Windows NT 4 0 Service Pack 4 media e Novell NetWare 3 12 Server that supports IPX network protocol e Novell IntranetWare Client for Windows NT v4 11b installation media Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 05 05 1 0 Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3C0M 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C509B network adapter Power on the machine and boot to a DOS bootable disk Insert the 3C0M 3C509 driver disk and execute 3C5X9CFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration a A W N If changes are required save those changes and exit 7 Remove the 3COM 3C509B driver disk and reboot the system to Windows NT 7 Installing the 3COM EtherLink IIl 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 3 12 Server 8 Log onto Windows NT4 Workstation with administrator privileges
31. ng to values noted above and click on Next Perform NIC Test and click on Next if the adapter is operating correctly Perform Network Connection Test and click on Next if connectivity is verified Do not configure Dynamic Access feature and click on Next Do not save setting for a future NIC installation and click on Next Click on Finish to complete the installation 23 Set the path to A in the dialog box and click on Continue 24 At the Show Bindings for prompt accept the default settings and click on Next 25 Click on Next to start the network 5 Installing the 3COM EtherLink IlI 3C509B ISA 10BT Network Adapter Connecting to a Windows NT 3 51 Server 26 Specify your Computer Name Workgroup or Domain Contact your network administrator if you do not have the required information and click on Next 27 Click on Finish to complete the installation 28 Remove the 3Com driver disk from the floppy drive and select Yes at the prompt to shut down and restart your computer for the new settings to take effect 29 Log onto Windows NT4 Workstation with administrator privileges 30 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer 31 Install the Hewlett Packard Soft Power Down application once the Service Pack 4 has been installed 6 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter M
32. ow to change LAN card configuration if needed Advanced users only This is a general advisory on how to forcibly modify resources for ISA and PCI network cards ISA cards e For ISA network adapters start the configuration tool provided in driver kit See install documentation e Under CMOS setup go to Advanced gt PnP PCI ISA IRQ Resource Exclu sion gt reserve an IRQ for the adapter PCI cards e For PCI network adapters go to CMOS setup gt Advanced gt PnP PCI ISA IRQ Resource Exclusion gt reserve the IRQ for Legacy ISA ISA cards can t use IRQ9 e IRQ 9 is reported as being used by ACPI during POST This is due to ISA s inability to share IRQs e Using a different IRQ e g 5 7 10 and 11 will work For this 1 Install the NIC then power up the system Press F2 to go to CMOS setup Set PnP OS to NO and reserve IRQ 5 7 10 or 11 explained in installation section Save the configuration settings and boot to the applicable OS Follow installation steps Sound conflict under Win 95 on VLi8 only e On VLi8 LAN cards cause an IRQ conflict with the embedded sound de vice under Win95 e To solve the problem Reserve IRQ 5 and sett PNP OS to no For this 1 Install the NIC then power up the system General information to read before installing 2 Press F2 to go to CMOS setup 3 Set PNP OS to NO and reserve IRQ 5 4 Save settings and boot to applicable OS 1 Installing the 3COM EtherLink Ill 3C509B IS
33. p newer files when a file being copied is older than the file currently on your computer 14 Click on OK when the system prompts for the computer and workgroup names 15 Enter the Computer Name Workgroup and Computer Description in the appropriate spaces and click on Close Contact your network administrator if you do not have the required information According to 83COM click on OK to ignore the error message indicating Error enumerating cards The NIC specific DLL TCAUM509 did not find any NICs present 16 Click on YES to restart the system when prompted 17 From the location of the Novell Client for Windows 95 v 2 5 installation files execute Setup exe 18 Click on Yes to accept the License Agreement 19 Select Custom installation and click on Next 20 Select Bindery NetWare 3 x and click on Next 21 Click on Install to start the installation 22 Click on Yes to set the Preferred Server If you do not have the required information contact your network administrator 23 Click on Reboot to complete the installation 24 Right click on the Network Neighborhood icon and select Properties 25 Accept the default Network Protocols and the Primary Network Logon to Novell NetWare Client as seen below and click on OK If you do not have the required information contact your network administrator 3 Installing the 3COM
34. re the error message indicating Error enumerating cards The NIC specific DLL TCAUM509 did not find any NICs present 17 Click on YES to restart the system when prompted 18 Right click on the Network Neighborhood icon and select Properties 19 Accept the default Network Protocols and the Primary Network Logon Client for Microsoft Networks as seen below and click on OK If you do not have the required information contact your network administrator 20 Client for Microsoft Networks Client for Microsoft Networks 3Com EtherLink II ISA 3C509b TPO in PnP mode 3Com TCAATDI Diagnostic TDI IPX SPX compatible Protocol NetBEUI 21 Click on OK to accept the configuration 22 When prompted specify the path to your Windows 95 files 23 Click on Yes when prompted to restart the system 3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 R2 5 3 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows 95 SR2 5 Connecting toaNetWare Requirements St 250148 e HP Vectra with Windows 95 SR2 5 e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and drivers disk version 6 0 e Driver File ELNK3ND3 SYS version 5 26 31 e Microsoft Windows 95 SR2 5 media e Novell NetWare 3 12 Server that supports IPX network protocol e Novell Client for Windows 95 v2 5 installation media Device Configuration Devic
35. the Windows NT Workstation Networking Setup dialog box 23 From the location of the Novell IntranetWare Client v 4 11b install files execute Setupnw exe 24 Click on the Continue button to proceed with the installation of the Novell IntranetWare Client 25 Click on Yes to agree to the Software License Agreement to begin installation 11 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Connecting to a Novell NetWare 4 11 Server 26 Click on the Reboot button to restart the machine for the changes to take effect 27 Install the Windows NT3 51 Service Pack 5 application 12 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Microsoft Windows for Workgroups 3 11 12 Installing the 3COM EtherLink II 3C509B ISA 10BT Network Adapter Microsoft Windows for Workgroups 3 11 Connecting to a Requirements Windows NE A DServe HP Vectra with MS DOS and MS Windows for Workgroups 3 11 e 3COM EtherLink I 3C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3 386 version 1 05 e Microsoft Windows for Workgroups 3 11 media e Microsoft Windows NT 4 0 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra VIi8 Vectra VEi7 Vectra VEi8 Interrupt 05 05 05 1 0 Address 300 300 300 Procedure 1 With the HP Vectra turned of
36. ton at the completion of the Novell NetWare Client installation to restart the machine for changes to take effect 34 Click on the IntranetWare tab of the Novell IntranetWare Client Services Login screen 35 Select Bindery Login and specify the Server Name Contact your network administrator if you do not have the required information 36 Click on the Login tab and specify your Name and Password to login 37 Install the Windows NT4 Service Pack 4 application to correct the error messages in the Event Viewer 38 Install the Hewlett Packard Soft Power Down application once the Service Pack 4 has been installed 8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation 8 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 4 0 Workstation Connecting to a Novell Requirements NetWare 4 11 Server HP Vectra with Windows NT 4 0 Workstation e 3COM EtherLink III 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND4 SYS version 5 26 40 e Microsoft Windows NT 4 0 Workstation media e Microsoft Windows NT 4 0 Service Pack 4 media e Novell NetWare 4 11 server that supports IPX network protocol e Novell IntranetWare Client for Windows NT v4 11b installation media Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 05 05 05 1 0 Address 300 300 300
37. ttings dialog box 20 If applicable press OK to continue from NWLink IPX SPX Protocol Configuration dialog box 21 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name 22 To complete the installation remove the floppy disk and click on Restart computer in the Windows NT Workstation Networking Setup dialog box 23 Install the Windows NT3 51 Service Pack 5 application 10 Installing the 3COM EtherLink Ill 3C509B ISA 10BT Network Adapter Microsoft Windows NT 3 51 Workstation 10 Installing the 3COM EtherLink III 3C509B ISA 10BT Network Adapter Microsoft Windows NT 3 51 Workstation Connecting to a Requirements Windows NT 4 0 Server HP Vectra with Windows NT3 51 Workstation e 3COM EtherLink II 8C509B TP ISA 10BT network adapter and driver disk version 6 0 e Driver File ELNK3ND3 SYS version 5 26 31 e Microsoft Windows NT 3 51 Workstation media e Microsoft Windows NT 3 51 Service Pack 5 e Microsoft Windows NT 4 0 Server system that supports NetBEUI NWLink IPX SPX Compatible Transport and NWLink NetBIOS network protocols Device Configuration Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEI8 Interrupt 10 05 05 I O Address 300 300 300 Procedure 1 With the HP Vectra turned off install the 3COM 3C509B network adapter into an ISA slot Connect network cable media to the 3COM 3C5

HP 3C509B ISA User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents