Home

HP 2240 User's Manual

1. Perform the following steps to close the system unit CAUTION Do not attempt to operate the workstation with the front cover removed The cover is needed for proper air flow for system cooling 1 Insert the two guide pins on the bottom of the front cover into the guides on the bottom of the system unit 2 Swing the front cover up and push it firmly into the workstation housing The front panel edges automatically align with the workstation housing and the top latch buttons pop up into posi tion See Figure B 2 NOTICE To maintain FCC EMI compliance verify that the top latches snap completely into position Figure B 2 Replacing the Front Panel 3 Reconnect the power cables and any other cables that you dis connected when opening the workstation then power on any pe ripherals the monitor and the system unit B 9 Installing Your workstation can have any two of the following removable media Removable devices with no two the same Media Devices CD ROM drive 2to 8 GB 4mm DDS tape drive 3 5 inch Floppy disk drive Follow these steps for installing any of the removable media drives into the Storage Assembly The steps for checking and setting drive jumpers are different for each drive Jumper information for each drive is included in these steps NOTICE
2. SCSI ID Address Jumpers SCSI ID Jumpers nedress ioe 104 ibe Noo Ff WN O O O Figure B 12 Floppy Drive SCSI Address Jumper Settings B 23 B 24 Top View of Floppy Disk Drive SCSI Terminators Figure B 13 Floppy Drive Terminators 13 Figure B 14 shows the orientation of each of the removable me dia drives in the bracket and the position of the screws holding the drive bracket in place The same bracket can be used on all three drives 6 Flo Drive 2 ppy Uriv l 8 G 8 amp 8 CD ROM Drive DDS Drive Figure B 14 Attaching Removable Drive Mounting Bracket and Drive Orientation B 25 14 With the disk mounting bracket between the guides on each side of the Storage Assembly slide the disk into the Storage Assem bly securing it with the two side screws See Figure B 15 Do not over tighten the side screws P LE Reconnect the drive SCSI and power cables here Figure B 15 Replacing Drive Screws 15 Reconnect the cabling from the back of the drive to the side o
3. Cassette Drive Meaning Key Light Light OFF Cassette un loading a en y Cassette loaded online Aua Cassette loaded activity m PE eeen E Cassette loaded offline puree Amoer Pulsing Green Write Protect States and Amber Cassette un loading Cassette loaded online Cassette loaded activity Cassette loaded offline Error States Media wear caution High humidity Self test normal Self test failure 3 4 LED Warning Conditions DDS DC Drive The following sections describe actions to take if the LEDs indicate a warning condition High Humidity If the LEDs display the high humidity signal the humidity is too high and the drive does not perform any operations until the humidity drops Self Test Failure If the LEDs display the self test failure signal a fault was diagnosed during the self tests Note the pattern of the pulses and contact your local service representative Media Wear Caution Hewlett Packard DDS drives continually monitor the number of er rors they have to correct when reading and writing to a tape to deter mine tape wear and tape head cleanliness If excessive tape wear or dirty tape heads are suspected the drive warns you by displaying the Media Wear Caution
4. If you replace your workstation s monitor with a different monitor type and do not set the workstation s graphics parameters by using the monitor command before doing so you need to perform the fol lowing Wait two seconds after the Num Lock light flashes near the end of the boot sequence then press Tab to initiate the automatic monitor selec tion process NOTICE _ It takes approximately one to two minutes after powering on the workstation before the Num Lock light flashes The system cycles through all of the available monitor types one at a time When you can see a message similar to the following clearly and legibly select that monitor type by pressing Enter Path Slot Head Type Size Freq Class GRAPHICS 1 1 1 n nnnnxnnnn nnHz Press RETURN to select this monitor type type n of n types The system queries you to confirm your selection Press Y to save this monitor type If you press any key other than Y the following message is displayed Monitor type not saved At this point the new monitor type is active but not saved Because you didn t save the monitor type the next time you reboot the system the original monitor type will be used Next the following message is displayed To select a new Graphics Monitor Type press the lt TAB gt key now otherwise EXIT by entering any other key or will time out in 15 se conds To restart the monitor selection process press IAB Changing t
5. NOTICE If you are using a power saving monitor you will have less than 10 seconds from the time this message appears to press a key 4 Press a key You will then see the message Boot terminated The Main Menu of the boot console appears Booting Your Workstation Usually you start your workstation by turning it on and waiting for HP UX to boot automatically However you may not always want the usual sequence to occur For example you may want to start your workstation from an operat ing system that is stored on a device that is different from your usual boot device If your normal operating system kernel or the disk on which it resides becomes damaged or unusable you may wish to boot from a different disk or perhaps another type of device such as a DDS format tape drive Here are some situations and examples If you know which device you want to boot from and you know that it contains a bootable operating system follow the direc tions in Accessing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt boot device where device is the hardware path to the device specified in Mne monic Style Notation For example if you wish to boot an operating system that is stored on a DDS format tape in a drive that is located at sescsi 1 0 follow the directions in Accessing the Boot Console Interface earlier in this a
6. 1 Working from the rear of the workstation unscrew the four cap tive screws and pull the PCI EISA Assembly straight out using the handle See Figure B 34 AY Sa EA WEE N Qan g N Figure B 34 Removing the PCI EISA Assembly B 54 Figure B 35 PCI EISA I O Assembly B 55 2 Rotate the unit 90 degrees clockwise and place on a flat surface as shown in Figure B 36 Figure B 36 Rotating the PCI EISA Assembly for Installation B 56 3 Unscrew one screw at the back of the cover and lift the cover up and out to remove it from the PCI EISA Assembly See Figure B 37 Figure B 37 Removing the PCI EISA Assembly Cover B 57 4 Unscrew one screw at the top of the slot cover and pull the cover straight up to remove it See Figure B 38 WR AR WA Figur
7. 2nd Captive screw is below 1st but not visible in this view M S PRAI o NAL ANN SAX J SS O EIN S Drawer Ejector Handle SUIS 9 DAN nS DOi De hI ai ae fool SWAT IA OP WP 88 Figure B 19 Removing Storage Drawer from System Unit 3 Pull the Storage Assembly out as far as it will go A safety catch prevents the drawer from coming all the way out NOTICE When sliding the Storage Assembly out of the system unit move the drawer ejector handle to prevent the Storage Assembly from hitting it 4 Press in on the safety catch on each side of the drawer to allow the drawer all the way out and place the drawer on a flat surface B 33 B 34 3 Be sure you have already checked the SCSI ID of the drive you want to install using the method described at the beginning of this section With the disk mounting bracket between the guides on each side of the Storage Assembly slide the disk into the Storage Assem bly securing it to the drawer with two side screws See Figure B 20 Do not over tighten the side screws The drives should be placed in the drive bays with the bottom of each drive toward the middle as shown in Figure B 20 Refer to Figure B 18 for drive orientation in the bracket Figure B 20
8. DDS tape drive and data cassette descriptions Setting the write protect tab on a data cassette Operating the DDS tape drive Loading and unloading a data cassette Using device files Archiving data in compressed and non compressed mode Troubleshooting Ordering information 3 2 This chapter describes how to perform tasks that archive to and trans fer data from the optional DDS tape drive It also describes how to maintain and care for the drive We assume the DDS tape drive is set to the factory default address of SCSI ID 3 The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface CAUTION Use only data cassettes labeled DDS Digital Data Storage cassettes Never use audio cas settes labeled DAT Digital Audio Tape in your DDS format drive DDS Tape Drive and Data Cassette Descriptions This section describes basic information needed for using your DDS tape drive and data cassettes Depending on your configuration your DDS drive may be a DDS DC drive or a DDS 2 drive NOTICE In most cases the information for using these drives is the same however in a few instances such as the LED codes the information dif fers for each drive For the purposes of this dis cussion wherever we refer to simply the DDS drive that information is for both dri
9. If you use these device files you do not need to create any device files Archiving Data in Compressed and Noncompressed Mode This section describes how to transfer data to and from a DDS for mat data cassette saving and restoring using the HP UX tar com mand and your tape drive s device file NOTICE Before using your DDS format tape drive to back up your file system make sure you read the Media Interchangeability Restrictions section later in this chapter The tar tape file archiver command allows you to save files to a data cassette restore files from a data cassette to your system or list files on your data cassette Writing to a Data Cassette Use the following instructions to save files to a data cassette 1 Check that the write protect tab on the data cassette is in the write position 2 Load the data cassette into the tape drive 3 Ina terminal window enter the following command line to write to the tape tar cvf dev rmt devicefile pathname where devicefile is one of the device files listed from sam and pathname is the pathname of the file or directory containing files that you want to write to the tape To use the data compression mode use one of the device file names t
10. M Activity load or unload Ea Steady Green Eg Activity read or write Steady Amber i Cartridge loaded oi Flashing Green 1 2 sec on 1 2 sec off Any Cleaning needed Flashing Amber 1 2 sec on 1 2 sec off Any Fault E E Fast Flash Green 1 4 sec on 1 4 sec off Data Cassettes Media Life HP DDS data cassettes are currently specified to 2000 passes over any part of the tape under optimal environmental conditions 50 relative humidity 22 degrees C During a tape operation any one area of the tape may have multiple passes over the heads This trans lates into approximately 200 to 300 backups or restores Under certain conditions the life of your data cassette is less Replace your data cassettes after 100 backups or restores if your operating conditions meet any of the following criteria The relative humidity in your operating environment is consis tently less than 50 You know that the backup software you are using makes multi ple passes over sections of the tape during backups or restores You notice that when you do backups and restores the tape stops and starts frequently Cleaning the Tape Heads Clean the heads of your tape drive after every 25 hours of tape drive use or if the Media Wear Caution signal is displayed on the
11. opening the system unit B 6 B 7 operating system overview 1 19 1 23 ordering information DDS format tape cassettes 3 19 floppy diskettes 4 12 P parallel connector 1 15 pointing devices general information 1 18 power connector 1 16 power switch system unit 1 6 1 9 problems See solving problems product description See system description PS 2 connectors 1 14 Q questions suggestions or problems xviii R rcp command 1 23 release documents xv remotely copy files See rep command removable drives attaching mounting bracket B 25 removable media CD ROM drive B 16 DDS tape drive B 18 floppy drive B 22 revision history xvi rlogin command 1 22 RS 232 connector 1 15 pinout 1 15 S safety and regulatory statements xv A 1 SAM utility adding a hard drive B 35 B 37 configuring the floppy driver 4 12 mounting a CD ROM disc 2 15 2 17 unmounting a CD ROM disc 2 17 2 18 SCSI assigning device IDs fast wide C 24 C 28 single ended standard C 20 C 23 bus lengthfast wide differential C 14 C 16single ended standard C 11 cables C 6 configuration constraints C 8 fast wide differential C 10 connections C 1 connectors and terminator C 8 device IDs C 18 C 28 port connections C 26 restrictions C 6 C 10 SCSI bus differences C 3 C 5 SCSI connectors 1 16 SCSI IDs jumpers CD ROM drive B 17 DDS 2 drive B 20 DDS DC
12. E1196 E0597 E1297 Revision History First printing Second printing Third printing Fourth printing Fifth printing Latest printing Documentation Unless otherwise noted in the text this guide uses the following sym bolic conventions Conventions literal values user supplied values sample user input ouTpUL Screen Button Bold words or characters in formats and command de scriptions represent commands or key words that you must use literally Pathnames are also in bold Italic words or characters in formats and command descriptions represent values that you must supply In examples information that the user enters appears in color Information that the system displays appears in this typeface A colored rectangle with rounded corners and a key label denotes a key on your keyboard In this manual we refer to the Enter key On your keyboard the key may be labeled either Enter or Return This colored symbol with a label in it denotes an HP VUE screen button A screen button is a key or button which is drawn on your workstation s graphic display by HP VUE It works like a keyboard key except that you must move the mouse cursor over it and press the left mouse button to activate it The screen button s la bel describes its function This
13. The floppy disk drive ships with the drive set to SCSI ID address 0 We recommend keeping the address setting at 0 unless it is used by another device CAUTION Floppy disk drives are susceptible to mechanical and electrostatic shock When handling the drive always wear the static grounding wrist strap that came in the floppy disk drive kit Always handle the drive carefully If you need to change the floppy disk drive s address follow these instructions referring to Figures B 12 and B 13 If you do not need to change the drive s address go to Step 10 of this installation procedure 1 Locate the jumpers on the top of the floppy drive 2 To change the jumpers use needlenose pliers to set the drive s SCSI ID to an address that is not used by another SCSI device Check that the other jumpers are set correctly NOTICE Do not use SCSI ID 7 for your floppy drive s SCSI address The host SCSI controller uses SCSI ID 7 3 Use needlenose pliers to remove the SCSI terminators if still attached to the drive B 22 Jumper in 0 out 1 Top View of Floppy Disk Drive ID2 ID1 IDO Ce ee lo SCSI ID Address Jumpers ee ce EBEE
14. cific resolution and frequency If you replace your workstation s mon itor with a different type of monitor you must reconfigure your workstation to support the new monitor The Monitor Command The monitor command lets you change your workstation s graphics configuration This command is available in Configuration Menu of the boot console interface NOTICE The monitor command lets you change your workstation s graphics configuration before you replace your monitor For information about changing the configuration after you replace your monitor refer to Changing Your Monitor Type in Appendix B To display the current graphics and console information enter the following command Main Menu Enter command gt co Configuration Enter command gt mo The correct usage for setting the graphics configuration is mo graphics_path type where valid graphics_path parameters are D 16 graphics 0 through graphics 2 Graphics adapters installed in op tion slots 0 through 2 and type is the numerical monitor type For example a Dual Visualize Enhanced Graphics Card A4451A installed in option slot 2 would be graphics 2A and graphics 2B Displaying the Current Monitor Configuration D 18 To display the current monitor configuration for your system from the Configuration Menu of the boot console interface follow the direc tions in Accessing the Boot Console Interface earlier in this appen
15. dix Once you are in the Boot Console Interface Main Menu enter Main Menu Enter command gt configuration This places you in the Configuration Menu From here enter Configuration Menu Enter command gt monitor The screen displays a list of the current graphics adapters and there monitor types configured for your workstation MONITOR INFORMATION Path Slot Head HPA Resolution Freq Type Class GRAPHICS 1 1 1 8000000 1280x1024 72Hz 12 Configuration Menu Enter command gt In this example only the graphics adapter located in slot 1 graph ics 1 is configured The monitor type for graphics 1 is set to type 12 which is a 1280 by 1024 monitor that uses a frequency of 72 Hz Setting the Monitor Type You can set the monitor type for a graphics adapter by entering the following Configuration Menu Enter command gt monitor graphics 7 tt Where n is the number of the graphics adapter and tt is the monitor type To display a list of supported monitors enter the following command Configuration Menu Enter command gt monitor list A list of valid monitor types similar to the following is displayed MONITOR INFORMATION Path GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 Slot Head Type Size 0 1 1 1280x1024 0 il 2 1280x1024 0 1 3 1280x1024 O 1 4 1280x1024 0 1 5 1024x768 0 1 6 800x600 0 1 7 640x480 0 1 8 1600x1200
16. HElp lt menu gt lt command gt RESET MAin Search for boot devices Set show security mode Read or set real time clock in GMT Boot from specified path Redisplay the current menu Display help for menu or command Restart the system Return to Main Menu Configuration Menu Enter command gt ALL Boot INfo CAche ChipRevisions COprocessor FwrVersion IO LanAddress MEmory PROocessor WArnings Display all system information Display boot related information Display cache information Display revisions of VLSI and firmware Display coprocessor information Display firmware version Dispay I O interface information Display built in system LAN address Display memory information Display processor information Display selftest warning messages BOot PRI ALT lt path gt Boot from specified path Display Redisplay the current menu HElp lt menu gt lt command gt Display help for menu or command RESET MAin Restart the system Return to Main Menu Information Menu Enter command gt Servi Ce UGeh assess Command ChassisCodes lt proc gt CLEARPIM EepromRead lt addr gt lt len gt MemRead lt addr gt lt len gt a PDT CLEAR PIM lt proc gt HPMC LPMC TOC BOot PRI ALT lt path gt Display HElp lt menu gt lt command gt RESET MAin Service Menu Enter command gt Display chassis codes Clear zero the contents of PIM Re
17. some of which your monitor won t display Wait for the workstation to display your monitor type again then select it B 65 SCSI Connections Appendix C SCSI bus differences SCSI restrictions Determining SCSI bus length Assigning SCSI device IDs Connecting to the SCSI ports C 1 This appendix provides information about connecting Small Comput er System Interface SCSI devices to an HP 9000 J282 2240 workstation The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface NOTICE When attaching external SCSI devices be sure to terminate the last device on the external SCSI bus If no external devices are attached the SCSI connector on the rear of the system must be terminated with the terminator that was shipped with your workstation A Small Computer Systems Interface SCSI bus is an IEEE standard SCSI Bus Differences bus for connecting your workstation to internal and external devices SCSI devices running at different speeds singly or in combination Examples of these SCSI devices are floppy disk drives 4 mm DDS format tape drives CD ROM drives and Winchester hard disk drives There are three types of SCSI buses available with this workstation a narrow single ended NSE SCSI bus a fast wide differential FWD SCSI bus and an ultra fast wide single en
18. stand vmunix prev If you do not know which media in your file systems have boot able operating systems you can find them with the search IPL command Searching for Bootable Media To list devices that contain bootable media follow the directions in Accessing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt search ipl The search command searches all buses The search may turn up more devices than there are lines on your display If you are using a text terminal you may control the progress of the search from your terminal s keyboard by performing the following steps To hold the display temporarily press Ctrl S To continue the display press Ctrl Q To halt the search press any other key These flow control commands do not work with a bitmapped display but such a display can show more than forty lines of text so you are unlikely to need them To search for devices of just one type that actually contain bootable media follow the directions in Accessing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt search ipl device_type where device_type is one of the following fwscsi is the built in fast wide SCSI bus sescsi is the built in single ended SCSI bus lan is all connections to the built in LAN gscn is an optional fast wide SCSI interfac
19. system under the heading Ultra Wide SCSI Device Drives and each drive s SCSI device ID under the heading Device ID Num ber 2 Add your new drive to the table 3 Check to see what SCSI device IDs are not used You may use ID numbers 0 through 6 and 8 through 15 if they are not already in use If the default ID on your drive does not conflict with any existing drive IDs use that ID If your default address conflicts with an existing drive ID assign a new fast wide SCSI device ID to your drive Refer to the drive s installation documentation for information on changing the device ID CAUTION Do not use SCSI device ID 7 for any device Table C 11 Ultra Wide SE SCSI Device IDs Ultra Wide Single Ended Device Drives a7 sees Ist Internal Device 6 2nd Internal Device 5 NOTICE You can have no more than 4 SCSI devices connected to an UWSE bus C 25 Connecting to the SCSI Ports C 26 This section describes how to connect to the system SCSI ports nar row single ended ultra wide SE and fast wide differential System SCSI Port Connection The system contains two 2 SCSI connectors System Single Ended SCSI 2 Connector System Fast Wide Differential or Ultra Wide SE SCSI Con nector Figure C 1 shows the rear panel with terminators attached to the two SCSI connectors Figure C 2 shows the two SCSI conn
20. y q X Lay Figure B 26 Replacing the CPU Assembly B 44 14 15 16 Next align the bottom of the CPU Assembly with the guide on the system unit With the ejector latches in the open position slide the CPU Assembly into the system unit as far as it will go See Figure B 26 Press the ejector tabs all the way in and press on the left edge of the processor module sheet metal to ensure that the processor module is completely seated in the connector Replace the two screws in the center of the CPU Assembly Make sure the ejec tors are completely depressed to ensure proper connector seating Close the system unit and reconnect all cables as described in the Closing the System Unit section in this appendix To verify that this installation was successful follow the steps in Appendix D of this book The Boot Console Interface on dis playing memory information If you have only replaced a faulty DIMM you must issue the pdt clear command in the service menu of the Boot Console Interface Answer yes y to the prompt Continue Y N gt B 45 Replacing the Perform the following steps to replace the processor module on your workstation Processor Module 1 Open the system unit according to the directions in the Opening
21. 0 5 0 sdisk CLAIMED DEVICE DEC DSP3210SW target 2 8 0 6 tgt CLAIMED DEVICE disk 0 8 0 6 0 sdisk CLAIMED DEVICE DEC DSP3210SW ba O 8 12 bus_adapter CLAIMED BUS_NEXUS Core I O Adapter ext_bus 2 8 12 70 CentIf CLAIMED NTERFACE Built in Parallel Interface audio O 8 12 1 audio CLAIMED NTERFACE Built in Audio tty O 8 12 4 asio0 CLAIMED NTERFACE Built in RS 232C ext_bus 1 8712 5 c700 CLAIMED NTERFACE Built in SCSI target 3 87 12 52 COL CLAIMED DEVICE disk 8 12 5 2 sdisk CLAIMED DEVICE TOSHIBA CD ROM XM 4101TA target 4 8 12 5 3 tgt CLAIMED DEVICE tape 8 12 5 3 stape CLAIMED DEVICE HP HP35480A target 5 8 12 5 4 tgt CLAIMED DEVICE disk O 8 12 5 4 sdisk CLAIMED DEVICE SEAGATE ST3600N target 6 8 12 5 6 tgt CLAIMED DEVICE disk 5 8 12 5 6 sdisk CLAIMED DEVICE MICROP 2112 lan O 8 12 6 lan2 CLAIMED NTERFACE Built in LAN ps2 O 8 12 7 ps2 CLAIMED NTERFACE Built in Keyboard Mouse be 2 10 ccio CLAIMED BUS_NEXUS I O Adapter graphics O 10 0 graph3 CLAIMED NTERFACE Graphics graphics 1 10 8 graph3 CLAIMED NIERFACE Graphics ext_bus 3 10 12 c720 CLAIMED INTERFACE GSC add on Fast Wide SCS nterface target 7 10 12 4 tgt CLAIMED DEVICE disk 6 10 12 4 0 sdisk CLAIMED DEVICE SEAGATE ST31200W graphics 2 0 16 graph3 CLAIMED NTERFACE Graphics ba 1 10 20 bus_adapter CLAIMED BUS_NEXUS Core I O Adapter hil O 10 20 1 hil CLAIMED NTERFACE Built in HIL tty 1 1072072 asio0 CLAIMED NTERFACE Built in RS 232C ba 2 10 2075 eisa CLAIMED BUS_NEXUS EISA Bus Adapter
22. 1 21 J jumpers SCSI ID CD ROM drive B 17 DDS 2 drive B 20 DDS DC drive B 19 floppy drive B 23 K keyboard connector 1 14 L LANIC ID 1 20 Index 3 laser safety statements A 6 A 7 LCD system unit 1 6 1 9 LED removable device 1 8 system unit 1 6 1 9 LEDs CD ROM drive 2 19 2 20 DDS 2 tape drive 3 6 3 8 display codes 3 6 DDS DC tape drive 3 4 3 8 display codes 3 4 logging in from a remote terminal See rlogin command M mail 1 22 media interchangeability restrictions DDS tape drive 3 8 mediainit command floppy diskette 4 8 memory configuration B 38 B 45 memory failures 5 11 5 17 memory SIMM sequence B 42 monitor changing type boot console interface B 64 setting the type at power on B 64 monitors 1 17 mounting a CD ROM disc 2 15 2 17 mouse general information 1 18 mouse connector 1 14 mt command DDS format tape drive 3 18 Index 4 N network connectors 1 15 Network File System NFS 1 23 networking overview 1 22 1 23 ftp command 1 23 mail 1 22 Network File System NFS 1 23 rcp command 1 23 rlogin command 1 22 telnet command 1 22 O on line help cpio command 3 18 4 10 cstm command 5 15 fbackup command 3 18 floppy information 4 11 ftio command 3 18 ftp command 1 23 mediainit command 4 11 mt command 3 18 rcp command 1 23 rlogin command 1 22 tar command 3 18 4 10 telnet command 1 22
23. 1420 0314 Use of any other battery may cause fire or explosion A 7 A 8 Appendix B Changing Your Workstation s Hardware Configuration Checking the SCSI IDs Opening the system unit Closing the system unit Installing removable media devices Adding a hard drive Installing additional memory Installing an EISA or graphics board Changing your monitor type B 1 This appendix describes the procedures to change your workstation s hardware configuration The instructions in this appendix assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface CAUTION Always wear a properly grounded wrist strap when reconfiguring your workstation Use the following tools to remove or replace hardware parts when changing your configuration Light duty flat blade screwdriver with 150 mm 6 in blade Number 1 Posi drive driver T10 T15 and T20 Torx drivers Needlenose pliers Also read the ESD Precautions in Appendix A of this guide Checking the To determine which SCSI IDs are currently in use on your system SCSI IDs use the ioscan command in a terminal window 1 Click on the Terminal Control on the Front Panel of your Workspace Terminal Control A terminal window opens 2 Move t
24. 8 4 19 0 as the built in SCSI bus controller For devices connected to the built in SCSI bus such as disks the fourth number is the SCSI ID for that device For example the listing 8 4 19 0 6 0 tells you that there is a SCSI device a disk currently using ID 6 on the SCSI bus NOTICE Never use SCSI address 7 for any device Ad dress 7 1s reserved for the SCSI controller Opening the System Unit B 6 Perform the following steps to open the system unit 1 Power off the system the monitor and any peripheral devices Unplug the system unit power cord and the power cord of any peripheral devices from ac wall outlets Refer to Using Your HP Workstation for the proper method of shutting down your work Station Attach the static grounding wrist strap by following the instruc tions on the package Attach the sticky end of the wrist strap to bare metal on the back panel of the system unit Press down on the two buttons on the top front of the worksta tion releasing the front panel also known as the front bezel as shown in Figure B 1 Figure B 1 Removing the Front Panel 4 Swing the panel down and pull up slightly so the two guide pins on the bottom clear their guides and lay the front cover down Closing the System Unit
25. B 18 Floppy Dive dikisar ra tees eal aa ows ae ee B 22 Adding a Hard Dive orrir essn donni ERRETEN h eA B 29 Installing a Hard Disk Drive B 32 Configuring a Hard Drive 000008 B 35 Installing Additional Memory 0 00 c eee eee ees B 38 Replacing the Processor Module 0000005 B 46 Installing an EISA PCI or Graphics Board B 51 Changing Your Monitor Type 0 0 aaea ee eee B 64 Setting the Monitor Type from the Boot Console Interface B 64 Setting the Monitor Type at Power On B 64 Appendix C Appendix D SCSI Connections SCSI Bus Differences mes sho5h5 dw es doh GS alk be SE C 3 SCSIRGSiMCHONS 2 2 id 4sish e tid oe dda tawieaead C 6 CAVES aeaa sa ec alec tins 80h oes Brera AEN Os ae C 6 Connectors and Terminator 00 0 cece eae C 8 SCSI Configuration Constraints 000 00 C 8 Narrow SE SCSI Bus Configuration Constraints C 8 Fast Wide SCSI Bus Configuration Constraints C 10 Ultra Wide SE SCSI Bus Configuration Constraints C 10 Determining SCSI Bus Length 0005 C 11 Narrow SE SCSI Bus Length 05 C 11 Fast Wide SCSI Bus Length 4 C 14 Ultra Wide SE SCSI Bus Length C 16 Assigning SCSIDevice IDs 0 0 0 0 C 18 Narrow Single Ended System SCSI Device IDs C 20 Past W
26. Before opening the system unit follow the instructions in Checking the SCSI IDs earlier in this appendix to determine the SCSI IDs currently in use on your workstation 1 Open the system unit according to the directions in Opening the System Unit earlier in this appendix 2 Unscrew the two captive screws on the left side of the Storage Assembly and pull down the drawer ejector handle on the right side of the Storage Assembly as shown in Figure B 3 The Storage Assembly slides partway out of the drawer B 10 EEn O X A 1st Captive Screw 2nd Captive screw is below 1st but not visible in this view M S PRAI o NAL ANN SAX J SS O EIN S Drawer Ejector Handle SUIS 9 DAN nS DOi De hI ai ae fool SWAT IA OP WP 88 Figure B 3 Removing Storage Drawer from System Unit 3 Pull the Storage Assembly out as far as it will go A safety catch prevents the drawer from coming all the way out NOTICE When sliding the Storage Assembly out of the system unit move the drawer ejector handle to prevent the Storage Assembly from hitting it 4 Push in on the safety catch and continue pulling the drawer ou
27. LED NOTICE Only use HP Cleaning Cassettes HP92283K to clean the tape heads Do not use swabs or other means of cleaning the tape heads Follow this procedure to clean the tape heads 1 Insert the cleaning cassette into the drive The tape automatically loads the cassette and cleans the heads At the end of the clean ing cycle the drive ejects the cassette 2 Write the current date on the label on the cleaning cassette so that you know how many times you have used it Discard the cleaning cassette after you have used it 25 times 3 7 3 8 Media Restrictions If you interchange media between other HP workstation DDS tape drives note that data cassettes with compressed data can only be read by tape drives that have data compression capabilities This includes data cassettes that contain both compressed and noncompressed data Setting the Write Protect Tab on a Data Cassette You can only store or change information on a data cassette when the write protect tab is in the write position So before trying to write to the data cassette make sure that the write protect tab is in the write position as shown in Figure 3 2 mkh INa ridhl dr write mkh INa dp dir write protect Figure 3 2 Setting the Write Protect Tab on a DDS Tape To protect information on a data cassette from being overwritten set the write protect tab to the write protect position as s
28. Q LY n ENS A Ejector Tab wey AG sine JA UY M A j aS Ty ee o i j X Q LULA aq Fi Ejector Tab Figure B 21 Removing the CPU Assembly Pull the CPU Assembly straight out and place on a flat surface with an antistatic mat 4 The CPU Assembly is heavy very warm and NOTICE has no safety catch Be sure to pull it out slow ly making sure it is properly supported Use Figure B 22 to locate the memory DIMMs on the CPU As sembly S B 39 Memory DIMMs Tis Memory Bracket Figure B 22 Memory Retention Bracket and Memory DIMM Loca tion NOTICE When installing DIMMs you need to orient the notch toward the white ejector handles 6 To install a new memory DIMM turn the CPU assembly until the memory DIMMs are in the position shown in Figure B 23 B 40 7 Memory DIMMs Position Guide Figure B 23 CPU Assembly Orientation Refer to the Position Guide on the CPU board that states lt POSITION MEM MODULE AS SHOWN as shown in Figure B 23 Install pairs of DIMMs in the following o
29. See also home direc tory home directory A shorthand way of referring to a frequently used directory almost always the login directory host See cluster server host name See internet protocol address HP UX cluster See cluster node cluster server HP Visual User Environment A user interface that draws a graphical layer over the complexities of the other layers of the system the hardware operating system and X Window system enabling you to control your workstation by direct ly manipulating graphical objects instead of by typing commands at a command line prompt HP VUE See HP Visual User Environment icon A small graphic representation of an object Objects can be ico nized turned into icons to clear a cluttered workspace Icons can be restored to their original appearance when needed Whatever pro cesses are executing in an object continue to execute when the object is iconized GL 11 GL 12 iconify See iconize iconize To turn a window or shell into an icon See also icon Initial System Loader The program that actually controls the loading of the operating sys tem input device Any of several pieces of hardware equipment used to give informa tion to a system Examples are the keyboard and the mouse See also output device input window The window that displays a program s prompt and any commands typed but not yet executed internet protocol address IP addr
30. access memory ROM Read only memory root See superuser scroll bar A vertical or horizontal bar located on the side or bottom of a window that allows the user to view information that does not fit within the window SCSI See Small Computer System Interface server A program that controls all access to input and output devices session The time between when you log in and when you log out Also called a work session or a login session See also current session shell A command line interpreter program used to invoke utility programs Some examples of HP UX shells are the Bourne Korn Key and C shells Sometimes referred to as a command interpreter See also command interpreter shell command An instruction you give the system to execute a utility program or shell script See also shell script utility program GL 19 GL 20 shell script A file that contains commands that the system can interpret and run in a Shell shutdown The process of taking the system from multi user state to system ad ministration state SIMM See Single In line Memory Module single ended standard SCSI An 8 bit wide SCSI bus with standard receivers and drivers which limits total cable length to 6 meters See also fast wide SCSI Small Computer System Interface Single In line Memory Module A memory board slider One of the components of a scroll bar The slider is the object that is dragged along
31. all the way in and press on the left edge of the processor module sheet metal to ensure that the processor module is completely seated in the connector Replace the two screws in the center of the CPU Assembly Make sure the ejec tors are completely depressed to ensure proper connector seating Close the system unit and reconnect all cables as described in the Closing the System Unit section in this appendix Installing an EISA PCI or Graphics Board Your J282 workstation s EISA Assembly has five slots Four are EISA slots of these two are EISA only and two are EISA GSC slots The bottom slot is GSC only Your J2240 workstation s PCI Assembly has five slots All five slots support PCI cards Three slots support 32 bit PCI and two support 64 bit PCI Two of the 64 bit slots and one of the 32 bit slots sup port GSC Slot 4 also optionally supports EISA NOTICE The 32 bit PCI slots expect 5 0V signalling while the 64 bit PCI slots expect 3 3V signal ling The graphics boards supported by your workstation provide HP VISUALIZE EG Fast 2D graphics HP VISUALIZE 8 24 Accelerated 8 plane or 24 plane graphics HP VISUALIZE 48 24 24 Image plane 24 bit Z buffer 3D graphics HP VISUALIZE FX2 FX4 FX6 J2240 only NOTICE Dual graphics boards take up two slots Other graphics boards may take one two or three slots Figures B 31 B 32 and B 33 show the physical layout of the EISA
32. as a file system For more information about how to mount and unmount the floppy drive see the manual Using HP UX B2910 90001 For more information on copying data to or from your system to other media including your floppy diskette refer to the cpio man page by typing the following in a terminal window man cpio For more information on copying to or from DOS files refer to the doscp man page by typing the following in a terminal window man doscp For more information on listing DOS directories refer to the dosls man page by typing the following in a terminal window man dosls For more information on using your floppy disk drive and floppy dis kettes refer to the floppy man page by typing the following in a ter minal window man floppy For more information on using the mediainit command refer to the mediainit man page by typing the following in a terminal window man mediainit 4 11 4 12 Configuring the Floppy Driver If you reload software or rebuild the Instant Ignition system on your workstation you need to reconfigure the HP UX Kernel to add the floppy driver Use the SAM utility to add the SCSI flexible disk driv er and build a new HP UX kernel For more information about how to reconfigure the kernel using SAM see the following manuals System Administration Tasks HP 9000 Series 700 Computers B2355 90040 Using HP UX B2910 90001 Troubleshooting If you have trouble with any of t
33. can be active at a time The active window is said to have the keyboard focus ANSI The American National Standards Institute a non profit organization made up of various expert committees that publishes standards for use by national industries ANSI has adopted the IEEE standards for local area networks argument The part of a command line that identifies the file or directory to be acted on GL 1 GL 2 attachment unit interface AUD A transceiver cable that conforms to IEEE 802 3 specifications back up v To make a copy of the file system on a tape or disk that can be stored separately from the original files Also called backing up the system or simply system backup bitmap Generally speaking an array of data bits used for graphic images Strictly speaking a pixmap of depth one capable of representing 2 color images boot Short for bootstrap service A service provided by a short program stored in the read only memory of your workstation that loads the operating system or any complex program into main memory Part ner workstations provide bootstrap service to diskless workstations See also boot ROM boot console interface The interactive program that enables you to interact with the hard ware of your workstation before the workstation boots the operating system The boot console interface allows you to perform special tasks display information and set certain system par
34. captive screws See Figure B 43 Q RA gt S IMS Te KAR o An AY iw KAR Re a A ia Figure B 43 Replacing PCI EISA Assembly B 63 Changing Your Monitor Type B 64 Your system ships from the factory preset to use a monitor with a spe cific resolution and frequency If you replace your monitor with a dif ferent type you must reconfigure your workstation to support it There are two ways to configure your workstation to support a differ ent monitor type Setting the Monitor Type from the Boot Console Interface To change your workstation s graphics parameters before you replace your monitor go to Displaying and Setting the Monitor Type in Appendix D Setting the Monitor Type at Power On If you replace your workstation s monitor with a different monitor type and do not set the workstation s graphics parameters by using the monitor command before doing so then press after your keyboard s lights flash during the boot process to initiate the automatic monitor selection process Your system queries you for the new monitor type Select the new type by pressing The system queries you to confirm your selection Press y to save this monitor type If you don t press y the system cycles through the other monitor types
35. describes the SCSI restrictions that apply to your work station in the following areas Cables Connectors and terminator SCSI configuration constraints Cables All SCSI devices ship without cables Only SCSI cables approved by HP can be used to connect your workstation and any SCSI devices HP offers the following SCSI cables for narrow single ended SCSI devices K2296 cable with 0 9 meter 3 feet length K2297 cable with 1 5 meter 5 feet length HP offers the following SCSI cables for connecting externally con nected devices to the system fast wide differential port C2911A cable with 0 9 meter 3 feet length C2924A cable with 2 5 meter 8 2 feet length C2925A cable with 10 0 meter 32 8 feet length C2926A cable with 20 0 meter 65 6 feet length HP offers the following SCSI cables for connecting externally con nected devices to the system ultra wide SE port C2978A cable with 0 5 meter 1 64 feet length CXXXXA p n 5183 3710 9 cable with 0 9 meter 3 feet length CAUTION SCSI cables approved by HP are designed to function within the SCSI tolerances for HP de vices Use of other cables can result in signifi cant problems with system operation Narrow singled ended SCSI definition limits the total cable length of SCSI cables to 6 meters 19 6 feet Fast wide differential SCSI definition limits the total cable length of SCSI cables to 25 meters 82 feet Ultra
36. diskless workstation workstation node name A unique identifying name given to a workstation in a cluster See also cluster node GL 15 GL 16 nonvolatile memory System memory that retains its contents even after workstation power is turned off object Any file directory or link in the network See also directory file link pathname operating system The program that supervises the execution of other programs on your workstation For example the entire HP UX system including the kernel and all HP UX commands See also kernel option See command option output device Any of several pieces of hardware used for receiving messages from the workstation Display screens and printers are examples of output devices See also input device output window The window that displays a process response to your command parent directory A directory that contains other directories each of which is then called a subdirectory See also subdirectory partner node A workstation that shares its disk with a diskless node See also disk less workstation password The word you enter next to the password prompt at login time Keep your password secret and change it occasionally in order to protect your account from unauthorized use See also user account path The hardware address of a device that is attached to the I O system of your workstation pathname A series of names separated by slashes that de
37. drive from its control If you use the dev rmt 3mn device file the drive does not rewind the data cassette The tape stays where it was after the last operation If you use these device files you do not need to create any device files Determining Available Device Files 1 Ina terminal window enter the following command sam _Enter_ 2 The System Administration Manager window opens Double click on Peripheral Devices gt The Peripheral Devices window opens Double click on Tape Drives gt The Tape Drives window opens In the list of tape drives clock on the desired tape drive to select it From the Action menu click on Show Device Files A window opens with a list of the device files for the selected tape drive with an explanation of each one 3 13 The tar tape file archiv er command saves files to a data cassette re stores files from a data cassette or lists files on a data cassette 3 14 Device Files Data Compression If you wish to use the data compression feature use the device files dev rmt 3he and dev rmt 3hen which are set for SCSI ID 3 If you use the dev rmt She device file the tape drive compresses the data and rewinds the data cassette every time the system releases the drive from its control If you use the dev rmt 3hcn device file the drive compresses the data but does not rewind the data cassette The tape stays where it was after the last operation
38. ejector tab by pressing down on it at the left of the con nector Refer to Figure B 25 B 42 10 Place the DIMM in the connector lining it up with the guides Make sure to put the notched end toward the white ejector han dle to the left Press down on ejector tabs to open them and place the DIMM in the connector so that the fingure is on the edge of the DIMM just touch the connector Press DIMM down slightly Ejector tabs pop partly back up Push ejector tabs until they lock in place Push the DIMM firmly and evenly into the connector to be sure it is properly seated Figure B 25 Installing Memory Cards 11 Close the ejector tab 12 Press firmly and evenly on the DIMM to ensure that it seats properly 13 To replace the CPU Assembly in the system unit first align the top of the CPU Assembly with the guide on the system unit Re fer to Figure B 26 and to the label on the back of the assembly Be sure to support the CPU Assembly properly while replacing it B 43 N Q S NARKA PPI GI GIGI GIGI SP SAH J 2 Y RY J Ne A z Y A o Z EI ay NIS y Ya Q 2 V YY NE 7 DANN Jok DY A WEA a WA AG ELT YS Ye i e AE K
39. ext_bus 4 10 20 5 3 hshpib CLAIMED NTERFACE EISA card HWPOC70 target 8 10 20 5 3 tgt CLAIMED DEVICE disk 7 10 20 5 3 cs80 CLAIMED DEVICE disk 07959 target 9 10 20 5 3 tgt CLAIMED DEVICE disk 8 10 20 573 cs80 CLAIMED DEVICE disk 07959 target O 10 20 5 3 Lot CLAIMED DEVICE disk 9 10 20 5 3 cs80 CLAIMED DEVICE disk 07959 processor O 32 processor CLAIMED PROCESSOR Processor processor 1 34 processor CLAIMED PROCESSOR Processor memory O 49 memory CLAIMED MEMORY Memory C 19 C 20 4 You can determine which SCSI IDs are currently in use by look ing under the H W Path heading The J2240 lists 8 4 19 0 as the built in SCSI bus controller For devices connected to the built in SCSI bus such as disks the fourth number is the SCSI ID for that device For example the listing 8 4 19 0 6 0 tells you that there is a SCSI device a disk currently using ID 6 on the SCSI bus Narrow Single Ended System SCSI Device IDs Before assigning a SCSI device ID to your drive you need to check your SCSI device IDs To check what SCSI device IDs are available and assign an ID to your device follow these instructions which use Table C 9 L Zs Write in the SCSI device ID of any internal drives in Table C 9 Write in the type of external drives single ended standard EISA or fast wide devices currently connected to your system under the heading External Device Drives and each drive s SCSI device ID u
40. in installing memory DIMMs before you begin DIMMs must be inserted in the order shown Refer to Figure B 24 You must insert DIMMs in pairs of equal size Be aware that it is possible to insert the DIMMs backwards into the connectors Be sure therefore that you understand the prop er orientation for DIMMs going into the connectors See Figure B 25 When you have finished installing additional DIMMs use the Boot Console Interface to verify that they are seen by the work station Perform the following steps to add memory DIMMs to your worksta tion Note the instructions in Step 8 of this section on DIMM configu ration before beginning these steps 1 Open the system unit according to the directions in the Opening the System Unit section earlier in this appendix 2 Remove the two screws in the center of the CPU Assembly 3 Release the ejector tabs on the left side top and bottom of the CPU Assembly Refer to Figure B 21 B 38 a f ANW ff T Bt GQQ x BE AAAQAQAAQA MA f I R A RRRS RSN RSNA RSRSRS ES WWIGI GIGI QISS SW SS WPMD WH GY WM gVg BW VB S N Wl R N aN kre L Th SSeS ea wae DWE GePQ PPPOE WoWsW WWW VW sWsWsWsWsWSBS WW AWTS SRNT DT SQSQVQp geQsapqebasapme OS QSOS QS QP QSQSQP aro
41. on Audio Connectors Figure 1 4 System Unit Rear Panel Connectors The symbols shown to the left of the connector descriptions in the following text such as the headphone and microphone for audio connectors are the same symbols used on the rear panel of the J282 2240 workstation Audio Connectors Your workstation has audio input and output capability through exter nal input and output connectors on the rear panel and through an in ternal speaker The rear panel contains the Audio IN stereo line in Mic microphone in Audio OUT stereo line out and Headphones headphones out connectors Headphones OUT Mic IN Connector Connector Audio IN Audio OUT Connector Connector Figure 1 5 Audio Connectors The audio connectors are standard stereo audio mini jacks Hewlett Packard recommends using gold plated plugs available through audio retailers for best quality recording and playback through the external connectors A summary of the workstation audio features follows Audio Features Audio Inputs Audio Outputs Audio CODEC Programmable sample rates SkHz 16kHz 32kHz 48kHz 11 025kHz 22 05kHz and 44 1kHz Programmable output attenuation 0 to 96dB in 1 5dB steps Programmable input gain 0 to 22 5dB in 1 5dB steps Input monitoring 16 bit linear 8 bit u law or A law coding Line in Mono microphone compatible with 1 5V phantom supply bias voltage supplied by the system
42. technician for help Hewlett Packard s system certification tests were conducted with HP supported peripheral devices and HP shielded cables such as those you receive with your computer Changes or modifications not ex pressly approved by Hewlett Packard could void the user s authority to operate the equipment Operation of this device is subject to the following conditions This device may not cause harmful interference This device must accept interference received including inter ference that may cause undesired operation Cables used with this device must be properly shielded to com ply with the requirements of the FCC A 3 VCCI CLASS 2 Emissions Regulations Compliance Acoustics TOREJ HHRMBRES ES RES ATMA BS VCCI OM TES PCIBARRMRECT CORBIS RERMRCHATS OLA BRIE LCWETA CORBASVAPTLEV a yR ALT Asht BIBS S FMI TCL MHVET HY Y e RBA INGE gt TIE LUMAR URL A LO FEL Any third party I O device installed in HP system s must be in ac cordance with the requirements set forth in the preceding Emissions Regulations statements In the event that a third party noncompliant I O device is installed the customer assumes all responsibility and liability arising therefrom Regulation On Noise Declaration For Machines 3 GSGV Lpa lt 70dB Lpa lt 70dB operator position am Arbeitsplatz normal operation normaler Betrieb per ISO 7779 nach DIN 45635 T 19 Electrostatic Electrostatic charges can damag
43. the SCSI connectors to connect external SCSI devices such as DDS format tape drives and CD ROM drives Consult the documen tation that accompanies each SCSI device for specific information concerning its use Refer to Appendix C for information about con necting SCSI devices to your workstation NOTICE When attaching external SCSI devices be sure to terminate the last device on the external SCSI bus Power Cord Connector Plug the workstation s power cord into the power cord connector to provide ac power to the system Monitors You can use one of the following HP monitors with your workstation 20 inch 1280x1024 color monitor A4033A 20 inch 1280x1024 color monitor A4331A 21 inch 1600x1200 color monitor A4576A Before using your monitor you should become familiar with its con trols connectors and indicators For information on these controls and indicators and on using your monitor see the documentation that came with it Pointing Devices 1 18 You can use an HP three button mouse PS 2 a trackball or other options as pointing devices with your workstation by using the serial ports For instructions on using your particular pointing device see the manual that came with it For general information on using three button mice and on the vari ous cursor shapes associated with different areas of HP VUE while using a mouse see Using Your HP Workstation Operating System Overview Your workstation
44. the scroll area to cause a change Small Computer System Interface SCSI An IEEE standard for interfacing a computer to multiple disparate high speed peripherals such as a floppy disk or a CD ROM singly or in combination See also fast wide SCSI single ended standard SCSI standalone A workstation that is not part of a cluster See also cluster Style Manager The HP VUE application that provides the ability to customize vari ous aspects of your system including colors fonts the keyboard the mouse session startup and termination behavior and access to other workstations subdirectory A directory that is located in or anywhere on a path below another directory The directory above the subdirectory is called the parent directory The subdirectory is also referred to as the child directory See also parent directory superuser A user with permission to enter the top level directory and make changes to files and programs that users are not allowed to change To become superuser or become root means to let the system know that you are now assuming the role of system administrator You can do this either by logging into the system as root or by typing su at a command line prompt You must know the root password to become root system administrator The person responsible for system and network installation updating maintenance and security at your site system call Invocation of a kernel proces
45. use 02 3 Network Connectors Your workstation has built in ThickNet LAN AUI and TP Twisted Pair connectors for the 802 3 ETHERNET or 10 BaseT 100 BaseT J2240 only network Connections to ThinLAN networks require an external transceiver Your workstation will automatically select the correct network setting RS 232C Serial Input Output Connector You can attach a variety of pointing devices such as a mouse or trackball or peripheral devices to the RS 232C Serial Input Output SIO ports on the J282 2240 workstation Peripheral devices include printers plotters modems and scanners Consult the documentation that accompanies each pointing or peripheral device for specific in formation concerning its use The SIO ports are programmable You can set functions such as bit rate character length parity and stop bits The SIO Ports are used as an interface for serial asynchronous devices to the CPU The ports operate at up to a 19 2 K baud rate Table 1 2 shows the SIO connector pin listings The serial connectors are 9 pin D sub connectors Signal names are those specified in the EIA RS 232 standard 1 16 LE Ow Table 1 2 Serial I O Pins Pin No Signal Description 1 DCD Data Carrier Detect 2 RXD Receive Data 3 TXD Transmit Data 4 DTR Data Terminal Ready 5 GND Ground 6 DSR Data Set Ready 7 RTS Request To Send 8 CIS Clear To Send 9 RI Ring Indicator SCSI Connectors Use
46. zer the System Unit section earlier in this appendix 2 Remove the two screws in the center of the CPU Assembly Ejector Tab Ejector Tab Figure B 27 Removing the CPU Assembly 3 Release the ejector latches on the left side top and bottom of the CPU Assembly Refer to Figure B 27 B 46 4 Pull the CPU Assembly straight out and place on a flat surface with an antistatic mat 5 Locate the CPU shroud as shown in Figure B 28 l l i za K7 Uf PAG R Figure B 28 CPU Shroud Location J282 2240 6 Disconnect the fan cable s from the system board NOTICE Be sure to reconnect the fan cables when you have finished installing the processor The fan not being connected will cause the system to shut down after about 15 seconds of operation 7 Remove the two screws attaching the shroud cover to the shroud then slide cover off Set the shroud cover aside B 47 NOTICE The Model 282 and 2240 can be configured with two processors A single processor must be located in slot 0 Do not mix 282 and 2240 processors in the same system 8 When replacing a processor module you must also remove the dust cover it wa
47. 0 0 0 ee eee eee eee D 36 Displaying PIM Information 0 0 cee eee eee D 37 Figures 1 1 System Unit Front Panel Controls t2 CID SVimGOls ost oie t etl Cg a Shee cg Aan 6 ai 1 3 System Unit with Removable Device Door Open 1 4 System Unit Rear Panel Connectors 1 5 Audio Connectors 0 cee eens 2 1 CD ROM Drive Controls and Features 2 2 CD ROM Disc Tray Partway Open 2 3 Placing the CD ROM Disc in the Disc Tray 224 Mise Tay Closed toes este es owes dae eae eats 2 5 CD ROM Disc Tray Partway Open 2 6 Removing the CD ROM Disc From the Disc Tray 22 Wise liay Closed ty xtc ea meea eae daw acaba eens 3 1 DDS Drive Controls and Indicators 3 2 Setting the Write Protect Tab ona DDS Tape 3 3 Loading a Data Cassette c pik cent Ge eb ae eta 4 1 Setting the Write Protect Tab on a Floppy Diskette 4 2 Inserting and Removing a Floppy Diskette B 1 Removing the Front Panel 0 B 2 Replacing the Front Panel B 3 Removing Storage Drawer from System Unit B 4 Removing FAN from EMI Plate B 5 Removing FAN screws 0 00 cece eee eee eee B 6 Removing FAN EMI plate 00 B 7 Removing drive screws 0 ccs B 8 CD ROM Drive SCSI Ad
48. 00 c eee 2 6 Loading and Unloading a CD ROM Disc 2 6 Loading a CD ROM Disc 0 000s 2 6 Unloading a CD ROM Disc 0050 2 9 Verifying the CD ROM Drive Operation 2 11 Usine Device Piles ercsi tah m a aa he 2 14 Mounting and Unmounting a CD ROM Disc 2 15 Mounting a CD ROM Disc Using SAM 2 15 Unmounting a CD ROM Disc Using SAM 2 17 Reading the Busy Light 0 0 2 19 TroubleshoOun 4022 sess 4 34 etl geo e Bee ee etna 2 20 Chapter 3 Using Your DDS Tape Drive DDS Tape Drive and Data Cassette Descriptions 3 3 DIDS DIVE Sons coy Siete an bed aea sales 3 3 Controls and Indicators 0 0 cee eee ee eee 3 3 LEDs DDS DC Drive vas we ee Pasha Sk eds 3 4 LED Warning Conditions DDS DC Drive 3 5 LEDS DDS ne neacd orate a dk E dia otras ea r Siatete ates 3 6 Dati Cassels sce di erate ede ae geet eee eames 3 7 Media Tate sisesta pied ead eo acd sane 3 7 Cleaning the Tape Heads 0 0000085 3 7 Media ReSUicuOns 2 oo oss 2 0sh 2vuate 4 eiaa pe A 3 8 Setting the Write Protect Tab on a Data Cassette 3 8 Operating the DDS Tape Drive 0 0000 3 9 Loading and Unloading a Data Cassette 3 9 iv Chapter 4 Chapter 5 Verifying the DDS Tape Drive Operation 3 10 sine Device PileS 45 5 bee neteake ee ete eed oe
49. 0O0O 00000 0 oo0oococ ooo OOO O00 0 0 0 J29 O O O Or OTO O 208 2 DON O O O OOOO oo0o0o0o0co0o0o0000 000000 oo0o000000000 0000000 Co0oO0O0O00O0000000 000 OD J28 O OOO 0 0 0 0 O e e OO OO O OO 0 oo00o00o0000000 00000 OO OO OOO OCOD OOOO OOO 8 oo0o0o0co0o0o0O0 0000000 0 o 14 lt J26 O o0o000O0O000000 000000 00 OO O 0 OO OO OOO OO 2 O oo0o0o0o0o0ce0o000 0000000 oo0o0o0co0o0 000000000 O CPU Modules j 2a J25 O oo0o00co0o00 0000000 000 Oo0o00000000000 00000 O oo0o0000000000 000000 Co00000000000 000 0 0 f J24 O Op ee ra A N O Ogooo 00 00000000 0600 0 oo0o00o0o0ce0 0000000000 o0000000 00000000 0 2A lt J23 O o0o0000000000000000 OO OO 0 6 0 0 O O 0 OO OO 0 0 O oo000000 0000000000 ooo OoCOoOOOoO OOOO OOO 0 Oo 8 H J22 O oo000000 0000000000 oo0o0o0o0o0o0 0000000000 oo00o0o0ce0ce0o0o000 000000 oo0o0o0o00oO0000000000 0 J21 O oo0o000000 00000000 00 ooo0oo000000000000000 oo0o000000000 0000000 Oo0O0000000000 00000 0B J20 O ooooo oOo oOOmCOC OOO OOOO ooo0o0o0o0o0o0o0o0000 00000 oo0o00O0O00C0O000 0000000 eoo0o0o0o0oO0O00 0000000 0 J19 ooooo ooo o0 OOOO OOO 8 ooo0o000000000000000 oo0o0o00000 0000000000 Co0O0O0O0C0O0O0C 000000 0 Of Figure B 24 Memory DIMM Sequence Pair 4 Pair 2 Pair 3 Pair 1 9 Open the
50. 0x00 0x00 Setting the Auto Boot and Auto Search Flags auto boot and auto search are variables stored in your workstation s nonvolatile memory Nonvolatile memory retains its contents even after power is turned off If you reset these flags to new value the change takes effect the next time you reboot the workstation auto boot boots the operating system whenever your workstation is turned on To examine the state of the auto boot and auto search flags type the following at the prompt Configuration Menu Enter command gt auto If auto boot is set to on your workstation automatically attempts to boot the operating system when turned on If auto boot is set to off your workstation enters the boot administration mode of the boot con sole user interface The state of the auto search flag determines how your workstation seeks a boot device during autoboot If auto search is set to on your workstation will search for other boot devices if the primary boot de vice is not available If auto search is off your workstation will de fault to the boot administration mode if it can t see the primary boot device To change the state of the auto boot or auto search flags type the following at the prompt Configuration Menu Enter command gt auto boot state or Configuration Menu Enter command gt auto search state where state is on or off D 31 D 32 Autosearch searches for devices in the following or
51. 1275 ext_bus Built in SCSI 0712752 target 6 127 54560 tape HP HP35480A If ioscan does not see any SCSI drives it will return the following message 1oscan No hardware found If you receive this message go to Chapter 5 Solving Problems 3 11 Device files are special files that tell your system which system hardware pathway to use when communicating with a specific device and what kind of device it is 3 12 Using Device Files Your system has four default device files for use with your tape drive two device files for noncompressed mode and two device files for compressed mode If you use these device files you do not need to create any device files If the SCSI address of your tape drive is not set to the factory default of SCSI ID 3 you must create a device file then substitute the path name of your device file in the examples that follow Refer to the Sys tem Administration Tasks manual for information on how to create a device file NOTICE The device file names depend on the naming conventions of your particular system See your Using HP UX manuals for more information Device Files No Data Compression Your system has two device files for using your tape drive with data compression turned off The device files are named dev rmt 3m and dev rmt 3mn and are set for SCSI ID 3 If you use the dev rmt 3m device file the tape drive rewinds the data cassette every time the system releases the
52. 2 We recommend keeping the address setting at 2 unless it is used by another device CAUTION CD ROM drives are susceptible to mechanical and electrostatic shock When handling the drive always wear the static grounding wrist strap that came in the CD ROM drive kit Always handle the drive carefully If you need to change the CD ROM drive s address follow these instructions referring to Figure B 8 If you do not need to change the drive s address go to Step 10 of this installation pro cedure 1 Locate the jumpers at the back of the CD ROM drive 2 To change the address use needlenose pliers to set the drive s SCSI ID to an address that is not used by another SCSI device Check that the other jumpers are set correctly NOTICE Do not use SCSI ID 7 for your CD ROM drive s SCSI address The host SCSI controller uses SCSI ID 7 3 Use needlenose pliers to remove the SCSI terminators if still attached to the drive 0 1 3 plelsHdslelse Hehee saut SHEHE PAHs O O Figure B 8 CD ROM Drive SCSI Address Jumper Settings B 18 DDS Tape Drive The DDS tape drive ships with the drive set to SCSI ID address 3 and the Operation Mode switches set for correct drive opera tion We recommend keeping the address setting at 3 unless it is used by another device CAUTION SCSI tape drives are susceptible to
53. 600N MEGROP Zila I O Adapter GSC add on Fast Wide SCSI Interface H W Path Claes bc 8 be 8 0 ext bus 8 0 lt 0 target 87 0040 disk 8 05 target 8 0 5 0 disk 3 0 6 target 8 0 6 0 disk 8 12 ba 8 12 5 ext_bus o 12 bs target 87127 522 0 disk 8 12 5 4 target 8 12 5 4 0 disk 87127 5606 target 871275660 disk 10 bc 10 12 ext_bus O7 I2sd target 10 12 4 0 disk SEAGATE ST31200W If ioscan does not see any SCSI disk drives it returns the follow ing message ioscan No hardware found If you receive this message go to Chapter 6 Solving Prob lems 2 13 2 14 Using Device Files Device files are special files that tell your system which pathway to use through the system hardware when communicating with a specific device and what kind of device it is To determine what device files are available for use with your CD ROM drive use the following procedure NOTICE The device file names will depend on the nam ing conventions of your particular system See SCSI ID and Device File Information for HP UX 10 20 or Later in Chapter 1 of this book In a terminal window enter the following command sam The System Administration Manager SAM window opens Double click on Peripheral Devices gt The Peripheral Devices window opens Double click on CD ROM Drives gt The CD ROM Drives window opens In the list of CD ROM drives click on the desired CD ROM drive to select i
54. 8 12 5 3 tgt CLAIMED DEVICE tape 8 12 5 3 stape CLAIMED DEVICE HP HP35480A target 5 8 12 5 4 tgt CLAIMED DEVICE disk 10 8 12 5 4 sdisk CLAIMED DEVICE SEAGATE ST3600N target 6 8 12 5 6 tgt CLAIMED DEVICE disk 5 8 12 5 6 sdisk CLAIMED DEVICE MICROP 2112 lan O 8 12 6 lan2 CLAIMED NTERFACE Built in LAN ps2 O 8 12 7 ps2 CLAIMED NTERFACE Built in Keyboard Mouse be 2 10 ccio CLAIMED BUS_NEXUS I O Adapter graphics O 10 0 graph3 CLAIMED NTERFACE Graphics graphics 1 10 8 graph3 CLAIMED NIERFACE Graphics ext_bus 3 10 12 c720 CLAIMED INTERFACE GSC add on Fast Wide SCS nterface target 7 10 12 4 tgt CLAIMED DEVICE disk 6 10 12 4 0 sdisk CLAIMED DEVICE SEAGATE ST31200W graphics 2 10 16 graph3 CLAIMED NTERFACE Graphics ba 1 10 20 bus_adapter CLAIMED BUS_NEXUS Core I O Adapter tty 1 10 20 2 asio0d CLAIMED NTERFACE Built in RS 232C ba 2 10 20 75 eisa CLAIMED BUS_NEXUS EISA Bus Adapter ext_bus 4 10 20 5 3 hshpib CLAIMED NTERFACE EISA card HWPOC70 target 8 10 20 5 3 tgt CLAIMED DEVICE disk 7 10 20 5 3 cs80 CLAIMED DEVICE disk 07959 target 9 10 20 7573 tgt CLAIMED DEVICE disk 8 10 20 5 3 cs80 CLAIMED DEVICE disk 07959 target 10 10 20 5 3 tgt CLAIMED DEVICE disk 9 10 20 5 3 cs80 CLAIMED DEVICE disk 07959 processor 0 32 processor CLAIMED PROCESSOR Processor memory O 49 memory CLAIMED MEMORY Memory 4 You can determine which SCSI IDs are currently in use by look ing under the H W Path heading The J2240 lists
55. 9 84 feet C 17 Assigning SCSI Before assigning a SCSI device ID to your drive you need to check Device IDs your existing SCSI device IDs To determine which SCSI device IDs are available for your device use the ioscan command in a terminal window 1 Click on the Terminal Control on the Front Panel of your Workspace Terminal Control A terminal window opens 2 Move the mouse cursor into the terminal window and single click the left mouse button 3 Enter the following at the prompt usr sbin ioscan f After a few moments the ioscan utility lists all of the SCSI I O devices it could find The list appears similar to the following Class H W Path Driver S W State H W Type Description be 0 root CLAIMED BUS_NEXUS be 1 8 ccio CLAIMED BUS_NEXUS I O Adapter ext_bus O 8 0 c720 CLAIMED NTERFACE GSC built in Fast Wide SCS nterface target O 8 0 0 CGC CLAIMED DEVICE disk 3 8 0 0 0 sdisk CLAIMED DEVICE QUANTUM LPS1080WD target 1 8 0 5 tgt CLAIMED DEVICE disk 2 8
56. Buttons and LEDs 1 8 System Unit Rear Panel Connectors 0005 1 10 PUdIO C ONNECIONS s 4 2 wwe Se hones ate ald Aha Boe 1 12 Keyboard COnnector 62 51 04 boosie st Sa e E RE 1 14 HP Parallel I O Connector 0 0 0 eee ee eee 1 15 802 3 Network Connectors 0 0 00 ees 1 15 RS 232C Serial Input Output Connector 1 15 SCSI COMneClOls 3 wtie ert a Sets Bader ake tiles 1 16 Power Cord CONNEC esorare otis dd eee Beets aoe 1 16 Mono cso Sige Suk es dee Swed he eed hat NS eek 1 17 Fonna DE VICES iis gnre re OR Ms a ET SRNA 1 18 Operating System Overview 0 0 cece eee ees 1 19 Important Information You Need to Note 1 20 IAIN TC DE sector sre nine See eee a eae aa 1 20 IP Address and Subnetwork Mask Information 1 21 Ne tworkins Overview soc 0S eR ae ado tiee pani 1 22 Mail 5 O25 ere tage he ein ee hth aes ete EA 1 22 E EEEE N A E E E E EER ates 1 22 HOSI saeddutee erann aE ahah oe Bae A A 1 22 iii ICO oe dine oh hed otha een eee E TOTEE 1 23 NES esenee eaea be oe Ae es hae tn eel a 1 23 Chapter 2 Using Your CD ROM Drive CD ROM Drive and CD ROM Media Descriptions 2 3 CDROM Dive i scceece eee eee twee sleet aaa 2 3 Controls and Features 2 0 02 rea a oat Su sete eee ees 2 3 CD ROM Media ccs neice male oe era doth ae 6 2 5 Caring for CD ROM Discs 000000 2 5 Operating the CD ROM Drive 0 0
57. CD ROM audio if internal CD ROM is installed Line out Headphone Mono speaker jacks Built in mono speaker Crystal CS4215 Table 1 1 summarizes the audio electrical specifications for this workstation Table 1 1 Audio Electrical Specifications Frequency Response 25 20 000Hz Input Sensitivity Impedance Line in 2 0Vpk 47kohm Microphone 22mVpk lkohm Max Output Level Impedance Line Out 2 8Vpp 47kohm Headphone 2 75 Vpp SO0ohm Speaker internal 5 88 Vpp 480hm Output Impedance Line Out 6190hm Headphone 1180hm Signal to Noise Line Out 65dB Headphone 61dB Speaker 63dB Line In 61dB Microphone 57dB THD w nominal load Line Out 73dB Headphone 70dB Speaker 68dB Line In 75dB Microphone 73dB To convert from dB to number of significant bits use the formula n B m For example for 61dB S N then n 61 6 10 20 log o 6 significant bits or in other words about 6 bits of noise Keyboard Connectors q i PS 2 Keyboard Connectors The PS 2 connectors provide an interface for the keyboard and mouse to the system Consult the documentation that accompanies each input device for specific information concerning its use 1 14 HP Parallel I O Connector The 25 pin HP Parallel I O interface uses Centronics interface proto cols to support peripheral devices such as printers and plotters Con sult the documentation that accompanies each peripheral device for specific information concerning its
58. CSI ID See Appendix C for default SCSI ID settings Check that all SCSI devices are cor rectly cabled Check that the SCSI bus is correctly terminated See Appendix C for information on SCSI cabling and termination Follow the instructions in Dealing With a Boot Failure later in this chapter If problems persist contact your system administrator or call your designated service representative Table 5 3 Problems with the 802 3 Network Problem Solution Can t reach other systems on the net work Applications that rely on the net work won t run Check the network connector on the back of the system unit Make sure that the network cable or transceiver is fastened securely to the connector If problems persist contact your system administrator or call your designated service representative 5 5 5 6 Table 5 4 Problems Using a Hard Disk Drive Problem Solution The disk drive is not Make sure that all SCSI devices are accessible or does set to the proper SCSI ID See Ap not respond pendix C for default SCSI ID set tings Check that all SCSI devices are cor rectly cabled Check that the SCSI bus is correctly terminated See Appendix C for information on SCSI cabling and termination Make sure that the system can com municate with the drive as described in Checking the SCSI IDs in Ap pendix B Follow the instructions in Deali
59. CSI device type Table C 5 Ultra Wide SE SCSI Bus Configuration Constraints Maximum Number of Each External Ultra Wide SE SCSI Devices Type of Device Allowed Ultra Wide SE Drive ultra wide disk drives only 2 Ultra Wide SE Disk Arrays addressed as a l single drive CAUTION Do not mix narrow single ended ultra wide SE and fast wide differential SCSI peripherals together on the same bus Determining SCSI Bus Length This section helps you to determine the total length of the narrow single ended SCSI bus the fast wide differential SCSI bus and the ultra wide SE SCSI bus Narrow Single Ended SCSI Bus Length Follow these instructions to calculate your total narrow single ended SCSI bus length including the system unit external SCSI devices and SCSI interconnect cables using Table C 6 1 Find all of your external NSE SCSI devices in the first column In the third column write the NSE SCSI bus lengths from the second column that correspond to your devices NOTICE In the third column the length for the System Unit is already listed This number must always be used for the system unit 2 Inthe fourth column write down the lengths of the NSE SCSI interconnect cables you are using for your inst
60. CUSTOMER S SOLE AND EXCLUSIVE REMEDIES EXCEPT AS INDICATED ABOVE IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL INCLUDING LOST PROFIT OR DATA OR OTHER DAMAGE WHETHER BASED IN CONTRACT TORT OR OTHERWISE FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND THE WARRANTY TERMS CONTAINED IN THIS STATEMENT EXCEPT TO THE EXTENT LAWFULLY PERMITTED DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU This document contains proprietary information that is protected by copyright All rights reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company RESTRICTED RIGHTS LEGEND Use duplication or disclosure by government is subject to restrictions as set forth in subdivision c 1 4i of the Rights in Technical Data and Computer Software Clause at DFARS 252 227 7013 Hewlett Packard Co 3000 Hanover St Palo Alto CA 94304 10987654321 Preface Chapter 1 Contents System Overview Product Descripuon sendigis estad becuse Galen Veta aed 1 3 System Unit Front Panel Controls LED and LCD 1 6 Sy Seri CD era Seas be pesos ve ae Ean eect TREE eA 1 7 System Power Switch iseset esitusi deregi i ian a e l 7 System Power LED t cs oct et i Be ee Se ade aS 1 8 Removable Device
61. Disc This CD ROM drive has an automatic loading ejecting feature To load a disc in the CD ROM drive follow these steps 1 Press and release the eject button on the CD ROM drive The disc tray opens partway as shown in Figure 2 2 Note the removable device door is not shown for easier viewing of the disk tray ql Figure 2 2 CD ROM Disc Tray Partway Open AS 2 Gently pull the disc tray fully open 3 Hold the disc by the edges with the label side up and place it in the disc tray as shown in Figure 2 3 ee A Figure 2 3 Placing the CD ROM Disc in the Disc Tray 4 Press down gently on the center of the CD ROM disc to make sure it is seated on the disc tray hub shown in Figure 2 3 5 Gently push the disc tray in until it is closed as shown in Figure 2 4 SY m N SS gt Figure 2 4 Disc Tray Closed Unloading a CD ROM Disc To unload a disc from the Disc Tray follow these steps 1 Press and release the eject button on the CD ROM drive The disc tray opens approximately 1 inch as shown in Figure 2 5 Yj LZ WAI Figure 2 5 CD ROM Disc Tray Partwa
62. Freq 75Hz THz 75Hz 75Hz Class VESA VESA Double buffered VESA Grey scale VESA Double buffered Greyscale 7T5HZ T H Z THz 79Hz VESA VESA VESA VESA D 19 D 20 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 GRAPHICS 0 Configuration Menu 10 11 12 13 14 Enter command gt 1600x1200 1200x1600 1200x1600 1280x1024 1280x1024 640x480 ToAzZ J5HZ T3HZ 72Hz 1282 60Hz VESA Grey scale VESA VESA Grey scale Double buff ered To set the monitor type for graphics Q to monitor type 2 enter the following Configuration Menu Enter command gt monitor graphics Q 2 This will take effect on the next reboot MONITOR INFORMATION Path Slot Head HPA Resolution Freq Type Class GRAPHICS 0 0 1 8000000 1280x1024 72Hz 2 The boot console displays a message that tells you that your new monitor selection will take affect the next time you reboot your sys tem The boot console also displays the new monitor information Trying to change the monitor type to a number not listed for that graphics device fails and gives you the following warning message Value of monitor type n out of range n nn Trying to change the monitor type on an empty slot fails and gives you the following warning message No such Graphics card D 21 Setting the Monitor Type at Power On D 22
63. GSC slots first from outside the system unit then from inside the PCI and EISA Assemblies B 51 B 52 Physical Slot Numbers On Outside of System 4 3 2 graphics 1 1 graphics 0 0 Figure B 31 EISA PCI GSC Slots from Outside the EISA PCI Assem bly Slot Numbers C so on Board Stott 3 so2t Cd CC Shot 2 Bottom of EISA soil SEO Sloot 1 Assembly sito L__ GSC Slots EISA Slots Figure B 32 EISA GSC Slots from Inside the J282 EISA Assembly Bottom of PCI Assembly lt Slot Number on Board f Slot 4 Slot 3 Slot 2 Slot 1 Slot 0 jit GSC Slots PCI Slots EISA Slots Figure B 33 GSC PCI EISA Slots from inside the J2240 PCI Assem bly Physical slot 0 is always reserved for graphics cards only graphicsO Graphics device in slot 0 If using a Dual Graphics Card this is the port to the right on the card when facing the back of the workstation graphicsl Graphics device in slot 1 If using a Dual Graphics Card this is the port to the right on the card when facing the back of the workstation graphics2 Graphics device in slot 2 If there is a Dual Graphics Card in slot 1 this is the port to the left on the card when facing the back of the workstation graphics3 This is a logical slot and can only be reached by using the left port of a Dual Graphics Card in physical slot 0 B 53 Follow these steps to install a PCI EISA or graphics board into your workstation
64. ID 2 The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface NOTICE Be sure you have read and understand the information on mounting and unmounting CD ROM discs before you begin using your CD ROM disc drive NOTICE Some procedures in this chapter require you to log in as root If you cannot log in as root con tact your system administrator CD ROM Drive and CD ROM Media Descrip tions This section describes basic information needed for using the CD ROM drive and CD ROM discs CD ROM Drive The CD ROM drive is a random access read only mass storage de vice that uses removable CD ROM discs The drive supports the ISO 9660 and High Sierra format standards You can access information from the drive like any other disk drive except that you cannot write to the drive The drive contains a semiconductor laser for reading data optically and includes an embedded controller with a SCSI interface Controls and Features Figure 2 1 and Table 2 1 describe the operating controls and features of the CD ROM drive P ee A dis o Headphone Busy Emergency Jack Indicator Eject Hole Volume Eject Control Button Thumbwheel Figure 2 1 CD ROM Drive Controls and Features 2 3 2 4 Table 2 1 CD ROM Drive Operating Controls and F
65. J282 2240 Owner s Guide O HEWLETT 2A PACKARD Workstation Systems Group HP Part No A2876 90015 Edition E1297 Printed in U S A Hewlett Packard Co 1997 First Printing December 1997 UNIX is a registered trademark in the United States and other countries licensed exclusively through X Open Company Limited NOTICE The information contained in this document is subject to change without notice HEWLETT PACKARD WARRANTY STATEMENT HP PRODUCT DURATION OF WARRANTY J282 J2240 one year 1 HP warrants HP hardware accessories and supplies against defects in materials and workmanship for the period specified above If HP receives notice of such defects during the warranty period HP will at its option either repair or replace products which prove to be defective Replacement products may be either new or like new 2 HP warrants that HP software will not fail to execute its programming instructions for the period specified above due to defects in material and workmanship when properly installed and used If HP receives notice of such defects during the warranty period HP will replace software media which does not execute its programming instructions due to such defects 3 HP does not warrant that the operation of HP products will be uninterrupted or error free If HP is unable within a reasonable time to repair or replace any product to a condition as warranted customer will be entitled to a refund of the purchase price upon pr
66. OTICE You can have no more than 7 SCSI devices internal and external connected to the system 5 Write in the SCSI device ID of any internal drives C 22 6 Write in the type of external single ended drives currently con nected to your workstation under the heading External Device Drives and each drive s SCSI device ID under the heading De vice ID Number 7 Add your new drive to the table if it is an external device If it is an internal drive continue to Step 8 NOTICE The C1700A Magneto Optical Autochanger uses three SCSI IDs and accounts for three of the seven devices allowed on the SCSI bus 8 Check to see which SCSI device IDs are not used You may use ID numbers 0 through 6 if they are not already in use If the de fault ID on your drive does not conflict with any existing drive IDs use that ID If your default address conflicts with an exist ing drive ID you need to assign a new SCSI device ID to your drive Refer to the drive s installation documentation for infor mation on changing the device ID CAUTION Do not use SCSI device ID 7 for any device It is reserved for the built in SCSI bus controller C 23 Fast Wide Differential SCSI IDs Before assigning a SCSI device ID to your drive you need to check your SCSI device IDs To check which SCSI device IDs are available and assign an ID to your device follow these instr
67. Placing Hard Drives in Storage Drawer 7 Reconnect the SCSI and power cables from the back of the drive to the side of the drawer assembly Slide the drawer back in and secure 9 Close the system unit and reconnect all cables as described in the Closing the System Unit section in this appendix 10 Follow the instructions in the Checking the SCSI IDs subsec tion to verify that your workstation can see the hard drive Configuring a Hard Drive This section describes how to add a hard disk drive to your system as a file system using SAM For more information about configuring a hard disk drive refer to the System Administration Tasks manual The procedures in this chapter require you to log in as root If you cannot log in as root contact your system administrator 1 Log inas root 2 Move the mouse pointer to the up arrow above the Toolbox control and click the left mouse button Toolbox Control Up Arrow B 35 3 4 SAM System Adminis tration Manager is a util ity that performs system administration tasks us ing a windows graphical user interface 6 J 8 B 36 The Toolbox subpanel opens Click on the General toolbox icon shown below General A file manager window appears with a number of icons in it Double click on the System_Admin toolbox icon System d
68. S 1 LASER PRODUCT LASER KLASSE 1 Warnings and Cautions WARNING Removing device cover may expose sharp edges in equipment chassis To avoid injury use care when installing customer add on devices WARNUNG Das Entfernen der Gerateabdeckung legt die scharfen Kanten im Inneren des Ger tes frei Um Verietzungen zu vermeiden seien Sie vorsichtig beim Einbau von zus tzlichen Bauteilen die vom Kunden selber eingebaut werden k nnen AVERTISSEMENT Des bords tranchants du ch ssis de l quipement peuvent tre expos s quand le cache de l unit n est pas en place Pour viter des blessures faire tr s attention lors de l installation de modules suppl mentaires par le client WARNING Disconnect power plug from wall outlet or power source before moving or removing the device or installing add on components WARNUNG Entfernen Sie die Stromzuf hrung von der Steckdose oder der Stromquelle bevor Sie das Ger t bewegen abbauen oder zus tzliche Bauteile installieren AVERTISSEMENT D brancher la fiche de la prise de courant ou de la source d alimentation lectrique avant de d placer ou de retirer l unit ou avant d installer des modules suppl mentaires WARNING Lithium batteries may explode if mistreated Do not put lithium batteries in fires or try to recharge or disassemble them Replace battery only with Matsushita Electric BR 2325 three volt lithium battery HP part number
69. You can only store or change information on a diskette when the write protect tab is in the write position So before trying to write to the diskette make sure that the write protect tab is in the write posi tion as shown in Figure 4 1 Push tab up for write Push tab down for write protect Figure 4 1 Setting the Write Protect Tab on a Floppy Diskette To protect files on a diskette from being overwritten set the write protect tab to the write protect position NOTICE The write protect tab should always be in the write position for formatting a new diskette and transferring data to a diskette 4 4 Inserting and Removing a Diskette Follow these steps to insert and remove a diskette from the floppy disk drive 1 Insert the diskette into the drive as shown in Figure 4 2 ject Button A Figure 4 2 Inserting and Removing a Floppy Diskette 2 Push the diskette into the floppy drive until it clicks into place 3 To remove the diskette push the eject button see Figure 4 2 then take out the diskette This section describes how to perform tasks with your 3 5 inch floppy Operating the Floppy Drive The iosc
70. ad EEPROM locations Read memory locations Display or clear the Page Deallocation Table Display PIM information Boot from specified path Redisplay the current menu Display help for menu or command Restart the system Return to Main Menu Accessing the Boot Console Interface To access the boot console interface follow these steps NOTICE This procedure should be done by a system ad ministrator 1 Close any files and applications on your workstation 2 Press the power switch on the front panel of the system unit NOTICE There is no need to manually shut down the HP UX operating system on your workstation before powering it off When you turn off the power switch your workstation automatically shuts down the operating system before termi nating the power Make sure that you do not unplug the system s power cord or other wise interrupt power to the system unit at this time 3 When the system has completely shut down power on your workstation If Autoboot is turned off the boot sequence automatically stops at the bootconsole Main Menu If Autoboot is turned on you will see the following messages Processor is starting Autoboot process To discontinue press any key within 10 seconds If Autoboot and Autosearch are both turned on you will see the fol lowing messages Processor is booting from first available de vice To discontinue press any key within 10 seconds D 7 D 8
71. allation Cable lengths are listed in subsection Cables in the section on SCSI Restrictions 3 Add up all of the numbers in the third column and write that number on the subtotal line at the bottom of the column Do the same for the fourth column 4 Add the subtotals together and write the total in the Total NSE SCST Bus Length box NOTICE The total length of the narrow single ended standard SCSI bus must not exceed 6 meters 19 6 feet If the number you write for Total NSE SCSI Bus Length is greater than 6 meters 19 6 feet try configuring your installation with shorter cables If you have problems call your designated service representative Table C 6 SCSI Bus Length Worksheet for Narrow Single Ended SCSI Bus NSE SCSI Device Internal NSE SCSI Bus Length Device Internal Length ane cei meters feet meters feet meters feet System Unit 1 7 5 6 1 7 5 6 A 7980S 0 0 0 0 ee ee A1999A U gt 1 0 CE C1520A 0 2 0 7 C1521A 0 2 0 7 a C1700C 1 1 3 6 C1701C 0 3 1 0 P C1704C 0 0 0 0 a C1705C 0 0 0 0 a C2213A 1 5 4 9 a C22 17T 1 3 4 3 Subtotals a Total NSE SCSI Bus Length Total NSE SCSI bus length not to exceed total of 6 meters 19 6 feet C 13 Fast Wide Differential SCSI Bus Length Follow these instructions to calculate your total FWD SCSI bus length for the FWD SCSI bus
72. ameters boot ROM A read only memory that is incorporated into a workstation for the purpose of starting the operating system testing the terminal and pro ducing a standard display bootstrap service See boot byte A fundamental character code unit usually consisting of 8 bits CD ROM Compact Disc Read Only Memory See also CD ROM disc CD ROM drive CD ROM disc CD ROM discs are identical to the audio compact discs CDs used to record stereo music except that they store data CD ROM discs are 120 mm 4 7 inches in diameter and use one data surface with a capacity of 600 MB The data surface contains pits and flat spots ar ranged in a continuous spiral track which is read at a constant speed CD ROM drive A random access read only mass storage device that uses remov able CD ROM discs The drive contains a semiconductor laser for reading data optically and an embedded controller with a SCSI inter face Central Processing Unit CPU The part of a workstation that interprets and executes instructions child directory See subdirectory GL 3 GL 4 click To press and release a mouse button The term comes from the fact that pressing and releasing most mouse buttons makes a clicking sound cluster A group of workstations connected via a Local Area Network LAN One workstation the cluster server performs as a file system server for the cluster clients See also cluster client
73. an failure Common Problems and Solutions The tables in this section list common problems you may encounter with your workstation The tables also tell you what to do to help solve the problems Table 5 1 Problems Powering Up the System Problem Solution The power LED Make sure all ac power cables are doesn t light connected securely to the system Make sure the power cord is plugged into a working ac outlet Make sure the power switch is set to the ON position The power LED Press the brightness control on the lights but the screen monitor to adjust it If the screen is is blank or flickers still blank turn off the system and monitor power switches When the system is completely powered off check the video cable connections Go to the section Changing Your Monitor Type in Appendix B for in formation about displaying and setting your workstation s monitor configura tion LCD messages See LCD Indicated Problems later in this chapter If problems persist contact your system administrator or call your designated service representative 5 3 5 4 Table 5 2 Problems Loading and Booting the Operating System Problem Solution The power LED is lit and text appears on the screen but more than two min utes have passed with no sign of system activity The system stops or hangs while booting Make sure that all SCSI devices are set to the proper S
74. an utility verifies the configuration of all drives disk drive Verifying the Floppy Drive Configuration To verify that your workstation can communicate with the floppy drive use the ioscan command in a terminal window to see which devices are currently in use on your system 1 Enter the following at a command prompt usr sbin ioscan d sflop After a few moments the ioscan utility lists all of the SCSI floppy I O devices it could find The list appears similar to the following H W Path Class Description bce 8 be I O Adapter 8712 ba Core I O Adapter 8 12 5 ext_bus Built in SCSI 8712 90 target 871275 0 lt 0 disk TEAC FC 1 HE 07 If ioscan does not see any SCSI drives it returns the following message ioscan No hardware found If you receive this message go to Chapter 6 Solving Prob lems 4 5 4 6 If the floppy driver is not configured ioscan returns the follow ing message ioscan Device driver scsifloppy is not in the kernel If you receive this message go the the section Configuring the Floppy Driver later in this chapter for information on adding the scsifloppy driver to the HP UX kernel configuration Using Device Files Device files are special files that tell your system which pathway to use through the system hardware when communicating with a specific device and what kind of device it is NOTICE The device file names depend on the naming conventions of your particul
75. and configured memory modules The second listing shows the in formation for a system that has memory modules incorrectly installed or configured Memory Information Sample 1 The following sample shows the memory information when memory modules are properly installed and configured MEMORY INFORMATION MEMORY STATUS TABLE SLot Size a b Status Oa b 64MB Configured la b 32MB Configured 2a b 128MB Configured TOTAL 224MB DETAILED MEMORY CONFIGURATION TABLE SPA GROUP SMC SMC Status Bank Bank Status Size Slot Ox00000000 1 O Configured 1 Configured 64MB 2a b 0 Configured 3 Configured 64MB Oa b 0 Configured 1 Configured 64MB 2a b 0x0c000000 O 2 Configured 0 Configured 16MB 1la b 2 Configured 2 Configured 16MB 1a b Group 1 interleaved 2 ways over 3 banks Group 0 interleaved 2 ways over 2 banks BAD MEMORY TABLE D 25 D 26 SMC SMC Status Bank Bank Status SIMM Size Slot 0 Present 0 Not Present OMB 5a b 2 Not Present OMB 4a b 1 Present 0 Not Present OMB 5a b 2 Not Present OMB 4a b 3 Not Present OMB Oa b 2 Present 1 Not Present OMB 3a b 3 Not Present OMB 3a b Active installed memory bytes 234881024 of Standard DRAM Deallocated pages bytes m O Available Memory bytes 234881024 Good Memory Required by OS bytes O Not Set by OS Memory HVERSION SVERSION 0x0710 Ox0900 Memory Information Sample 2 The following sample shows the memory information when memory modules are not properly installed and con
76. anel 1 10 1 16 RS 232 1 15 SCSI 1 16 serial 1 15 stereo line IN 1 12 stereo line OUT 1 12 controls system unit front panel 1 6 1 9 power switch 1 7 cpio command DDS format tape drive 3 18 floppy disk drive 4 10 cstm command 5 15 D DDS tape archiving data 3 14 listing files 3 17 restoring files 3 15 transferring data 3 14 writing to 3 15 DDS tape drive 3 1 cleaning the tape heads 3 7 3 8 controls and indicators 3 3 3 6 installing in system unit B 18 B 21 loading and unloading a data cassette 3 9 3 19 media interchangeability restrictions 3 8 3 18 media life 3 7 3 8 overview 3 3 3 6 troubleshooting 3 18 3 19 using device files 3 12 verifying the configuration 3 10 Index 2 DDS 2 data compression mode switch settings B 21 DDS 2 tape drive jumper settings B 20 LED indicators 3 6 3 8 display codes 3 6 DDS DC tape drive jumper settings B 19 LED indicators 3 4 3 8 display codes 3 4 DDS format tape write protect tab 3 8 DDS format tape drive write protecting a data cassette 3 8 description of system See system description device files overview CD ROM drive 2 14 DDS tape drive compressed mode 3 14 noncompressed mode 3 12 floppy disk drive 4 6 documentation conventions xvii E electronic mail See networking mail electrostatic discharge precautions A 5 emissions regulations A 3 exit command Su
77. ar system See SCSI ID and Device File Information for HP UX 10 20 or Later in Chapter 1 of this book If you set the SCSI address of your floppy drive to a value other than 0 you must create a device file for it Refer to the System Administra tion Tasks manual for information on how to create a device file To determine what device files are available for use with your floppy drive use the following procedure 1 Ina terminal window enter the following command sam _Enter_ 2 The System Administration Manager window opens Double click on Disks and File Systems gt 3 The Disk and File Systems window opens In the list of drives click on the floppy drive listing to select it From the Actions menu click on View More Information A window opens with a list of information for the floppy drive inlcuding the device files The tar tape file archiv er command saves files to a floppy diskette re Stores files from a floppy diskette or lists files on a floppy diskette 4 8 Formatting a New Diskette You must always format a new floppy diskette with the mediainit utility before using it To format a new floppy diskette follow these Steps 1 Log inas root 2 Make sure that the write protect tab on the floppy diskette is in the write position as shown in Figure 4 1 3 Insert the diskett
78. cluster node cluster server cluster client A cluster node that does not have a local HP UX file system Its file system resides on the cluster server See also cluster cluster node cluster server cluster node A member of a group of workstations connected via a Local Area Network LAN One workstation the cluster server performs as a server to the cluster See also cluster cluster client cluster server cluster server A workstation that provides file access login access file transfer printing and other services across a network to a defined cluster of systems cluster nodes connected via a LAN See also cluster clus ter client cluster node host command An instruction that you enter into the system at a prompt to execute a program or perform a task See also shell command command argument Information you provide on a command line to describe the object usually a file or directory to be operated on by the command command interpreter A program that reads lines of text from standard input typed at the keyboard or read from a file and interprets them as requests to execute other programs An HP UX command interpreter is called a shell See also shell command option Information you provide on a command line to indicate any special action you want the command to take See also default configuration The arrangement of a workstation or network as defined by the na ture number and chief charac
79. d Information For additional information on using tar and a complete list of the command arguments refer to the tar man page by typing the follow ing man tar You may also communicate with the tape drive with the cpio ftio mt and fbackup commands For more information on these com mands enter the following in a terminal window man command Media Interchangeability Restrictions If you interchange media between DDS format tape drives the fol lowing two restrictions apply to the media Data cassettes with compressed data can only be read by tape drives that have data compression capabilities such as the tape drive part number C1504 67201 found in Kit A2275A AHS Full height 5 1 4 in DDS format tape drives models HP 35470A and HP35480A can get 1 3 GB and can read or write to 60 meter data cassettes only if they are not using data com pression With data compression these drives can get 2 GB and can read or write to 90 meter cassettes Troubleshooting If you have trouble with any of these procedures for using your DDS tape drive see Chapter 6 of this book Solving Problems Ordering Information To order Hewlett Packard data cassettes and cleaning cassettes for use in your DDS tape drive use the following order numbers HP92283A Box of five 60 meter DDS data cassettes HP92283B Box of five 90 meter DDS data cassettes HP92300A Box of five 120 meter DDS data cassettes for DDS 2
80. d logtool utilities use the exit command The pdt can also be checked using the pdt command in the Service menu of the boot console handler If a failing DIMM is replaced use the Service menu pdt clear command to clear out the PDT 5 11 LCD Indicated Problems 5 12 Your workstation uses an LCD panel to display firmware OS progress codes The codes referred to as chassis codes consist of one of the mnemonics listed below followed by a 4 digit hex number identify ing the code module being executed The mnemonics and their mean ing are FLT A hardware error has been detected TEST Hardware being tested INIT Hardware being initialized SHUT System being shutdown WARN A non optimal operating condition exists RUN System is running operating system During a normal boot sequence a set of windows appear In gener al the LCD display has the following format Pid Seis gt 4 character OSTAT Ye eeese 2ee gt 4 digit hex code CRUXA seheseeseeos gt Functional CPUs in system Y eee reeeses Heart peat WWWWWWWWWWWWWWWW gt Text Diagnostic Message Lh AYY Selftest The windows are as follows Window 1 When the system is hard booted the LCD will be cleared and the fol lowing message will be displayed for approximately 1 second Then the processor dependent hardware pdh is verified Proceeding To lt line 1 Turn DC On lt line 2 Window 2 While the pdh is being ver
81. ddress logical_unit_number Built in SCSI core scsi scsi_address logical_unit_number Built in LAN core lan server_address init_timeout io_time out To display the current setting for a particular system path follow the directions in Accessing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt path path_type where path_type is one of the path types listed in Table D 1 For example to get the path to the primary boot device follow the directions in Accessing the Boot Console Interface earlier in this chapter and then type the following at the prompt Main Menu Enter command gt path primary To set a system path to a new value follow the directions in Acces sing the Boot Console Interface earlier in this chapter and then type the following at the prompt Main Menu Enter command gt path path_type path where path_type is one of the path types listed in Table D 1 and path is the specification of the path in Mnemonic Style Notation as de scribed in Table D 2 For example to set the primary boot path to a SCSI disk with an ID of 6 0 follow the directions in Accessing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt path pri sescsi 6 0 Displaying and Setting the Monitor Type Your system ships from the factory preset to use a monitor with a spe
82. ded UWSE SCSI bus Table C 1 shows the specification differences between these SCSI buses and Table C 2 shows the SCSI addresses ID num bers and arbitration priorities for each CAUTION Do not mix narrow single ended fast wide differential or ultra wide single ended devices on any one bus type Doing this will cause a system failure Table C 1 SCSI Bus Differences Transfer Data Bus Maximum Maximum Device Controller Rate Width Addresses Cable Physical Embedded or Length Location Plugable Narrow Single Ended 6 0 meters internal and embedded up to 19 6 feet external 5 Mbytes per second Fast Wide Dif ferential 16 bits 25 meters internal and embedded up to 82 feet external 20 Mbytes per second Ultra Wide Single Ended 16 bits 3 0 meters internal and embedded up to 9 84 feet external 40 Mbytes per second Address 7 is reserved for host controller use on both buses Only 2 external devices allowed total of 4 devices Table C 2 SCSI Bus Addresses ID Numbers and Arbitration Priorities 8 bit devices SCSI 2 Single Ended SCSI 2 SCSI 2 ID Number Address ISo we 8 Tar Priority f Loa 1 6 1 2 5 T or 3 4 4 3 5 2 6 1 1 0 8 15 1 9 14 10 13 11 2 12 11 1 13 10 a 14 9 1 15 8 16 16 bit devices SCSI 3 Fast Wide or Ultra Wide SE Bus SCSI Restrictions This section
83. der NOTICE Primary boot path Alternate boot path Built in fast wide SCSI devices Built in single ended SCSI devices Built in LAN bootp servers Fast wide SCSI adapter option cards installed in the option slots are not searched unless they are referenced by the primary or alternate boot paths EISA cards are not searched Displaying and Setting the Security Mode The SECure flag is a variable stored in non volatile memory Non volitalmemory retains its contents even after power is turned off If you reset this flag to a new value the change takes effect the next time you reboot the workstation When the SECure flag is set to on autoboot and autosearch are enabled and cannot be stopped The system boots from the default boot paths regardless of user intervention To display the current setting for the SECure flag enter the follow ing command secure To set the SECure flag on or off enter one of the following secure on secure off D 33 Displaying and Setting the Fastboot Mode D 34 When fastboot is enabled set to on your workstation does a quick check of the memory and skips I O interface testing during its power on self tests This enables your workstation to complete its boot pro cess quicker The default factory setting is for fastboot to be enabled on The fastboot mode allows your workstation to boot quickly by per forming a less extensive check of the system s memory When fastboot i
84. disk Using the proper shutdown method for your workstation and operating system also ensures that your system produces the proper diagnostic and self test messages and broadcasts a warn ing message to remote terminals that it is about to shutdown Follow the instructions in Using Your HP Workstation to shut down your workstation System Power LED The Power Light Emitting Diode LED is located on the left side of the front panel It lights when the system unit power is on and flashes until the OS is booted Once the OS is booted the LED remains on without flashing Removable Device Buttons and LEDs Depending on your configuration you can have up to two 2 of the following removable device drives CD ROM disc drive DDS tape drive Floppy diskette drive NOTICE You cannot have two of the same type of de vice For example you can have a CD ROM device and a floppy device but not two CD ROMs A description of each drive s controls and indicators is in the chapter describing that device later in this book Figure 1 3 shows the system unit with the removable device door open A removable device is in the top bay a blank covers the empty bottom bay 1 3 System Unit with Removable Device Door Open Figure System Unit This section describes the following connect
85. dress Jumper Settings B 9 DDS DC Tape Drive SCSI Address Jumper Settings B 10 DDS 2 Tape Drive and SCSI Address Jumper Settings B 11 Switch Settings for Data Compression Operation Mode B 12 Floppy Drive SCSI Address Jumper Settings B 13 Floppy Drive Terminators 004 B 14 Attaching Removable Drive Mounting Bracket and Drive Orientation 0 cee ees 1X B 15 Replacing Drive Screws 000 00 eee eee B 26 B 16 Replacing the Storage Drawer Assembly B 27 B 17 Fast Wide Hard Drive Jumper Settings B 30 B 18 Replacing Hard Drive Mounting Bracket and Drive Orientation 0 ees B 31 B 19 Removing Storage Drawer from System Unit B 33 B 20 Placing Hard Drives in Storage Drawer B 34 B 21 Removing the CPU Assembly B 39 B 22 Memory Retention Bracket and Memory DIMM Location 0 ees B 40 B 23 CPU Assembly Orientation 0 B 41 B 24 Memory DIMM Sequence 0005 B 42 B 25 Installing Memory Cards 20000050 B 43 B 26 Replacing the CPU Assembly B 44 B 27 Removing the CPU Assembly B 46 B 28 CPU Shroud Location J282 2240 040 B 47 B 29 J282 2240 Processor Modules 0005 B 48 B 30 Replacing the CPU Assembly B 49 B 31 EISA PCI GSC Slo
86. drive B 19 floppy drive B 23 SCSI 2 bus length C 11 configuration constraints single ended standard C 8 determining bus length C 11 C 17 serial connector 1 15 pinout 1 15 solving problems 5 1 boot failure 5 10 indicated by the LCD 5 12 5 14 memory failures 5 11 5 17 problems and solutions 5 3 5 9 Index 5 boot failure 5 4 CD ROM drive 5 7 DDS tape drive 5 8 floppy disk drive 5 9 hard disk drive 5 6 loading and booting the OS 5 4 network 5 5 powering up 5 3 system verification tests 5 15 5 17 Support Tools Manager 5 15 5 17 subnetwork mask information 1 21 Support Tools Manager 5 15 5 17 switches power 1 7 system administration manageradding a hard drive B 35 B 37configuring the floppy driver 4 12mounting a CD ROM disc 2 15 2 17unmounting a CD ROM disc 2 17 2 18 system description 1 3 1 5 system overview 1 1 system unitconnectors 1 10 1 16controls 1 6 1 9LCD 1 6 1 9LED 1 6 1 9power switch 1 6 1 9 system verification tests 5 15 5 17 7 tar command DDS format tape drive 3 14 floppy diskette 4 8 telnet command 1 22 Index 6 troubleshooting See also solving problems CD ROM drive 2 20 DDS tape drive 3 18 3 19 floppy disk drive 4 12 U unmounting a CD ROM disc 2 17 2 18 V verify command 5 16 W warning and caution statements A 7
87. drive only HP92283K Package of two cleaning cassettes HP92283L Lockable storage box for 12 cassettes CAUTION Use only data cassettes labeled as DDS Digital Data Storage cassettes Never use audio cassettes labeled DAT Digital Audio Tape in your DDS format drive 3 19 Chapter 4 Using Your 3 5 Inch Floppy Disk Drive Setting the write protect tab on a diskette Inserting and removing a diskette Verifying the floppy disk drive configuration Using device files Floppy disk drive device file Formatting a new diskette Transferring data to and from a floppy diskette Configuring the floppy driver Troubleshooting Ordering information 4 2 This chapter describes how to perform tasks that allow you to archive to or transfer data from the optional 3 5 inch floppy disk drive The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface NOTICES When examples of user input are given in this chapter enter them at the command line prompt in an HP VUE terminal window or HP UX shell Some procedures in this chapter require you to log in as root If you cannot log in as root con tact your system administrator Using the Floppy This section describes basic information needed for using your floppy Diskette diskettes Setting the Write Protect Tab on a Diskette
88. e sure that your working directory the directory in which a relative path name search begins is set to some directory other than the one under which the disc was mounted CAUTION If you wish to use a CD ROM disc as a mounted file system you must mount the CD ROM disc every time you load it into the drive You must also unmount the CD ROM disc every time you unload it from the drive Failure to mount or unmount a disc may cause a system error condition and may also require rebooting the system 1 Log inas root If you need information on logging in or setting up a user account see Using Your HP Workstation 2 Inaterminal window enter the following command sam _Enter_ 3 The System Administration Manager window opens Double click on Peripheral Devices gt 4 The Peripheral Devices window opens Double click on Disks and File Systems gt 2 17 2 18 The Disks and File Systems window opens Double click on CD ROM Floppy and Hard Disks The following screen message appears Scanning the system s hardware The CD ROM Floppy and Hard Disks window opens con taining a list of drives currently configured on this system Highlight the disc you want to unmount and click on Remove a Hard Disk Drive from the Actions menu A window with the following message opens D
89. e B 38 Removing the PCI EISA Slot Cover B 58 5 Place PCI GSC or EISA board you are installing in the board guides and slide firmly into the connector Check to see the board is evenly inserted to seat properly See Figure B 39 Figure B 39 Installing a PCI GSC or EISA or Graphics Board in the PCI EISA Assembly 6 Secure board with one screw in top of board connector bracket B 59 B 60 7 J2240 Only Before installing cover if you installed an EISA or graphics board that is taller than a PCI card remove the small break off block from the cover that corresponds to that slot Re fer to Figure B40 Figure B 40 Remove Block from PCI Assembly Cover 8 Insert cover in guide and secure with screw Refer to Figure B 41 Figure B 41 Replacing PCI EISA Assembly Cover B 61 B 62 Rotate the unit back 90 degrees as shown in Figure B 42 and grasp the handle Figure B 42 Rotating the PCI EISA Assembly Back 10 Slide the PCI EISA Assembly into the system unit and secure it with the four
90. e SE SCSI Bus Length Follow these instructions to calculate your total UWSE SCSI bus length for the UWSE SCSI bus on your system using Table C 8 1 List all of your internal UWSE SCSI devices in the first column In the second column write the lengths of the internal UWSE SCSI bus that correspond to your devices In the third column write down the lengths of the UWSE SCSI interconnect cables you are using for your installation Cable lengths are listed in subsection Cables in the SCSI Restric tions section Add up all of the numbers in the second column and write that number on the subtotal line at the bottom of the column Do the same for the third column Add the subtotals together and write the total in the Total SCSI Bus Length box NOTICE The total length of the UWSE SCSI bus must not exceed 3 meters 9 84 feet If the number you write for Total SCSI Bus Length is greater than 3 meters 9 84 feet try configuring your installation with shorter cables If you have problems call your designated service representative Table C 8 SCSI Bus Length Worksheet for Ultra Wide SE SCSI Bus External SCSI Device Internal SCSI Bus Length Device Internal Length Cable Length meters feet meters feet meters feet System Unit 1 7 5 6 1 7 5 6 N A C6390A 0 3 1 0 Subtotals Total UWSE SCSI Bus Length Total SCSI bus length not to exceed total of 3 meters
91. e Series 700 product family 20 inch 1280x1024 color monitor HP VISUALIZE EG 8 plane 2D graphics HP VISUALIZE 48XP 48 plane graphics HP VISUALIZE 8 24 Accelerated 8 plane or 24 plane 3D graphics HP VISUALIZE FX2 J2240 only HP VISUALIZE FX4 J2240 only HP VISUALIZE FX6 J2240 only 32 MB to 2 GB J282 32 MB to 3 3 GB J2240 only 32 MB to 4 GB J2240 running HP UX 11 x only Internal Storage Devices Fast Wide Differential SCSI Standard Network Standard I O J282 upgrade J2240 only hard disk drives up to two 2 or 4 GB Drives Ultra Wide SE SCSI hard disk drives up to two J2240 Only 4 or 9 GB Drives Single Ended SCSI removable Media up to two CD ROM Drive 2 0 8 0 GB 4 mm DDS tape drive Floppy drive Ethernet IEEE 802 3 AUI Thicknet or RJ45 UTP Twisted Pair 10 BaseT 100 BaseT J2240 Only One Narrow Single Ended SCSI 8 bit for removable devices 5 MB sec synchronous 1 5 MB sec asynchronous ALT 1 50 pin high density SCSI 2 connector One Fast Wide Differential SCSI for hard disk drives J282 upgrade J2240 only 20 MB sec synchronous 68 pin high density SCSI 3 P connector One Ultra Wide Single Ended SCSI for hard disk drives J2240 only 20 MB sec synchronous 68 pin high density SCSI 3 P connector Two serial interfaces RS 232C 9 pin male One parallel interface Centronics BUSY handshake 25 pin female EISA GSC PCI Five slots total J282 four EISA and
92. e for all the menus and commands by using either help he or and the menu or command you want help on SSS S Main Mente S 323 55 44332 SSS Command Description BOot PRI ALT lt path gt Boot from specified path PAth PRI ALT CON KEY lt path gt Display or modify a path SEArch DIsplay IPL lt path gt Search for boot devices COnfiguration lt command gt Access Configuration menu commands INformation lt command gt Access Information menu commands SERvice lt command gt Access Service menu comands Display Redisplay the current menu HElp lt menu gt lt command gt Display help for menu or command RESET Restart the system Main Menu Enter command gt D 4 AUto BOot SEArch ON OFF BootID lt proc gt lt boot LD BootINfo BootTimer 0 200 CPUconfig lt proc gt ON OFF DEfault FastBoot ON OFF LanConfig MOnitor LIST lt path gt lt type gt Display or set specified auto flag Display or modify processor boot ID Display boot related in formation Seconds allowed for boot attempt Config deconfig processor Set the system to predefined values Display or set boot tests execution Display or set LAN Configuration Change the current moni tor type PAth PRI ALT CON KEY lt path gt Display or modify a path SEArch Display IPL lt path gt SECure ON OFF Lime c y m d h m s BOot PRI ALT lt path gt DIsplay
93. e in slot number n Resetting Your Workstation To reset your workstation to its predefined values follow the direc tions in Accessing the Boot Console Interface earlier in this appen dix and then type the following at the prompt to access the Configu ration Menu Main Menu Enter command gt co When the Configuration Menu appears type the following at the prompt Configuration Menu Enter command gt default Displaying and Setting Paths A path is the hardware address of a device that is attached to the I O system of your workstation The path command sets the system paths shown in Table D 1 The path command sets and displays the hardware address of a speci fied device attached to the I O bus of your workstation Table D 1 System Paths primary or pri Your workstation s default boot device usually the root disk alternate or alt Your workstation s alternate boot device usual ly a DDS format tape device console or cone Your workstation s primary display device keyboard or key Your workstaton s primary input ASCII device To display the current settings for the system paths type the follow ing at the prompt Main Menu Enter command gt path The paths are displayed in Mnemonic Style Notation as shown in Table D 2 Table D 2 Mnemonic Style Notation for Boot Paths I O Type Specification Format Built in FWSCSI core fwscsi scsi_address logical_unit_number slotn fwscsi scsi_a
94. e into the floppy disk drive 4 Inaterminal window execute mediainit with an interleave of 2 by entering the following mediainit i 2 devicefile where devicefile is the device file as listed by sam Transferring Data To and From a Floppy Diskette This section describes how to transfer data to and from your floppy diskette saving and restoring using the HP UX tar command with your floppy drive s device file You need to set the write protect tab to the write position to transfer data to the diskette The write protect tab can be in either position when restoring data from a diskette or listing the files on a diskette Saving Files to a Floppy Diskette Use the following instructions to save files to a floppy diskette Check that the write protect tab on the floppy diskette is in the write position Load the formatted floppy diskette into the disk drive In a terminal window enter the following command line to write to the diskette tar cvf devicefile pathname where devicefile is the device file as listed by sam and pathname is the pathname of the file or directory containing files that you want to write to the diskette Restoring Files from a Floppy Diskette to Your System Use the following
95. e the integrated circuits on printed Discharge ESD circuit boards To prevent such damage from occurring observe the Precautions following precautions during board unpacking and installation Stand on a static free mat Wear a Static strap to ensure that any accumulated electrostatic charge is discharged from your body to ground Connect all equipment together including the static free mat static strap routing nodes and peripheral units Keep uninstalled printed circuit boards in their protective anti static bags Handle printed circuit boards by their edges once you have re moved them from their protective antistatic bags The Visible LED on this product is classified as Class 1 LED Visible LEDs PRODUCT in accordance with EN 60825 1 A 5 Laser Safety Statement For U S A Only IEC 825 Class 1 Laser Label A 6 For workstations that have a CD ROM drive installed The CD ROM mass storage system is certified as a Class 1 laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968 This means that the mass storage system does not produce hazardous laser radiation Because laser light emitted inside the mass storage system is completely confined within protective housings and exter nal covers the laser beam cannot escape from the machine during any phase of user operation CLAS
96. eals with installing a hard drive and the second part tells you how to configure your hard disk after it is installed Your workstation can have two hard drives The hard drive that came with your workstation was set to SCSI ID 6 If you are adding a se cond hard disk the second hard disk will use SCSI ID 5 If another device on your workstation is using SCSI ID 5 change the hard disk s SCSI ID to an unused SCSI ID NOTICE Do not use SCSI ID 7 for your hard drive s SCSI address The host SCSI controller uses SCSI ID 7 If you are adding a second hard drive we advise you not to use SCSI ID 6 which is normally reserved for the boot disk drive Check the jumpers on the hard drive you plan to install Figure B 17 shows the correct SCSI address for the jumpers on your drive These jumpers are the only jumpers you may need to change on the drive Use a pair of small needle nose pliers to set the SCSI ID jumpers to SCSI ID 5 if you are adding a second hard drive or SCSI ID 6 if this is the first hard drive you are running diskless Check that the other jumpers are set correctly If you removed the disk drive mounting bracket from the disk drive replace it now making sure not to over tighten the screws Figure B 18 shows the orientation of the drive in the bracket for both drives and the position of the screws holding the drive bracket in place Be sure the printed circuit side of one drive is facing the printed circuit side o
97. eatures Control Feature Purpose Headphone Jack Volume Control Busy Indicator Eject Button Emergency Eject Disc Tray You can plug mini headphones with a 3 5 mm diame ter miniature stereo plug into this jack Use the volume control to adjust the audio output vol ume to the headphone jack The Busy Indicator lights during a data access opera tion and blinks during a data transfer The indicator blinks initially and then stays lit when there is one of the following e A defective disc e A disc insertion error for example an upside down disc e No disc present Press the Eject Button to open the Disc Tray and in sert or remove a disc When the drive is in use you must press the eject button for more than one second to open the Disc Tray By inserting the end of a paper clip you can open the Disc Tray when the workstation does not have power The disc tray holds the CD ROM disc This style of CD ROM drive does not use a disc caddy The disc tray does not open if the workstation power is off NOTICE The Volume Control Headphone Jack and Audio Jack features of the CD ROM drive are supported through applications only CD ROM Media CD ROM discs are iden CD ROM discs are 120 mm 4 7 in in diameter and use one data tical to audio compact surface with a capacity of 600 megabytes The data surface contains discs CDs except that pits and flat spots arranged in a continuous spiral t
98. ectors without terminators SCSI cables connect to these ports with a high density thumb screw connector SCSI Terminators Figure C 1 Rear Panel SCSI Connectors with Terminators Attached C 27 C 28 Fast Wide Differential or Ultra Wide SE SCSI Connector Single Ended SCSI 2 Connector Figure C 2 Rear Panel SCSI Connectors without Terminators NOTICE The last device connected to the SCSI bus must be terminated with a SCSI terminator All of the devices listed ship without terminators If you do not already have a SCSI terminator you must order terminator K2291 NSE C2905A FWD or C2972A UWSE from Hewlett Packard Appendix D The Boot Console Interface This appendix describes the different features of the boot console in terface and how to use them It presents the information in the follow ing sections Boot console interface features Accessing the boot console interface Booting your workstation Searching for bootable media Resetting y
99. em s built in LAN Configure and Display LAN Settings J2240 Only The LanConfig command configures and displays the current LAN settings The hardware system supports 10Base T 100Base T and AUI standards To automatically select the network speed 100 Mbits sec and data transfer operation full or half duplex operating in compliance with IEEE 802 3u this is the default and recommended setting type the following at the prompt Configuration Menu Enter command gt LanConfig AUTO To select 10 Mbits sec network speed and half duplex mode type the following at the prompt Configuration Menu Enter command gt LanConfig 10 Half_dx D 35 To select 10 Mbits sec network speed and full duplex mode type the following at the prompt Configuration Menu Enter command gt LanConfig 10 Full_dx To select 100 Mbits sec network speed and half duplex mode type the following at the prompt Configuration Menu Enter command gt LanConfig 100 Half_dx To select 100 Mbits sec network speed and full duplex mode type the following at the prompt Configuration Menu Enter command gt LanConfig 100 Full_dx To select the AUI port 10 Mbits sec half duplex only type the fol lowing at the prompt Configuration Menu Enter command gt LanConfig AUI NOTICE The LAN setting defaults to LAN TP RJ45 If that setting fails the system tries the LAN AUI setting Also note that the new lan configura tion setti
100. es between your workstation and another computer system on the network For more information see the Using Your HP Workstation manual that came with your workstation and read the online man page by entering the following at a command line prompt man ftp rcp The rep application allows you to remotely copy files from another computer system on a network to your workstation For more infor mation see the Using Your HP Workstation manual that came with your workstation and read the online man page by entering the fol lowing at a command line prompt man rcp NFS The Network File System NFS allows your workstation to access files on remote computer systems as if they were on your local sys tem The file system on the remote computer system does not have to be compatible with your workstation s file system For more informa tion see Installing and Administering NFS Servers and HP UX System Administration Tasks manuals 1 23 Chapter 2 Using Your CD ROM Drive CD ROM drive and media descriptions Loading and unloading a CD ROM disc Verifying the CD ROM drive operation Using device files Mounting and unmounting a CD ROM disc Reading the busy light Troubleshooting 2 2 This chapter provides an overview of the optional CD ROM drive and media and describes how to use the CD ROM drive We assume the CD ROM drive is set to the factory default address of SCSI
101. ess A string of characters that uniquely identifies a workstation in a net work Also referred to as the IP address the system name and the host name invisible filename A filename in which the first character is a dot Invisible filenames are not displayed by the listing commands such as Is and Il without add options such as a IP address See internet protocol address ISL See Initial System Loader kernel The part of the operating system that is an executable piece of code responsible for managing the computer s resources The kernel con trols the rest of the operating system LAN See local area network LAN station address See local area network station address link n A special object that contains the name of another object When you specify a link as a pathname or part of a pathname the system substitutes the pathname that the link contains v To join together two or more objects local area network LAN A data communications system that allows a number of independent devices to communicate with each other The systems and clusters that share data hardware and software resources via Networking Ser vices software GL 13 GL 14 local area network station address The label that uniquely identifies the local area network LAN con nection for your workstation at the hardware level log in To initially sign on to the system so that you may begin to use it This creates
102. f the drawer assembly See Figure NO TAG 16 Secure the EMI plate at the back of the removable drives with the captive screw in the bottom of the plate 17 Slide the drawer back in B 26 18 Push the drawer ejector handle up until the Storage Assembly slides all the way into the system unit and secure the two captive screws on the left of the Storage Assembly as shown in Figure B 16 NOTICE Ifthe ejector handle is not pushed completely in you may not have proper seating of the SCSI PCB interconnect to the backplane 1st Captive Screw 2nd Captive screw is below 1st but not visible in this view Drawer Ejector Handle Fe RI Qe Q r l RN Jo gt TRA 9y oN QOG DAN MHA Ma Sa A 2 Y Lee Figure B 16 Replacing the Storage Drawer Assembly B 27 B 28 19 Follow the instructions in Checking the SCSI IDs earlier in this appendix to verify that your workstation can see the newly installed drive For information about using your drives see the following chapters in this book Using your CD ROM drive is in Chapter 3 Using your DDS tape drive is in Chapter 4 Using your floppy drive is in Chapter 5 Adding a Hard Drive This section describes how to add a hard drive to your workstation The first part d
103. f the other drive B 29 B 30 Jumpers FW SCSI Address On Highest alte 6 Priority OES O O DES O O LOO E O N W A OI omon O O O O OO O O O O OO OO OO OO OO OO oo ay OO OO E OO OO N iC CJ FOO 00 iC C O O O EE aa zomon OO OO OO 8 Lowest Priority Figure B 17 Typical Hard Drive Jumper Settings Top Drive PCB Side of Drive Bottom Drive Figure B 18 Replacing Hard Drive Mounting Bracket and Drive Orientation B 31 B 32 Installing a Hard Disk Drive Perform the following steps to install a hard disk drive NOTICE Before opening the system unit follow the instructions in Checking the SCSI IDs earlier in this appendix to determine the SCSI IDs currently in use on your workstation 1 Open the system unit according to the directions in Opening the System Unit earlier in this appendix 2 Unscrew the two captive screws on the left side of the Storage Assembly and pull down the drawer ejector handle on the right side of the Storage Assembly as shown in Figure B 19 The Storage Assembly slides partway out of the drawer EEn O X A 1st Captive Screw
104. figured In this sample the memory module in memory slot 1A is missing MEMORY INFORMATION WARNING Memory has been reconfigured due to a physical change or because the Page Deallocation Table PDT was cleared This 2s for information only No action is re quired MEMORY STATUS TABLE Slot Size a b Status 7 a eee la b MB SIMM not seated properly 2a b 128MB Configured oe DETAILED MEMORY CONFIGURATION TABLE SPA GROUP SMC SMC Status Bank Bank Status Size Slot 0x00000000 O 0 Configured 1 Configured 64MB 2a b 0 Configured 3 Configured 64MB Oa b 1 Configured 1 Configured 64MB 2a b Group 0 interleaved 2 ways over 3 banks BAD MEMORY TABLE D 27 SMC SMC Status Bank Bank Status SIMM Size Slot 0 Present 0 Not Present 2 Not Present 1 Present O Not Present 2 Not Present 3 Not Present 2 Present 0 Sizing Error 1 Not Present 2 Sizing Error 3 Not Present Active installed memory bytes of Standard DRAM Deallocated pages bytes Available Memory bytes OMB OMB OMB OMB OMB OMB OMB OMB OMB Good Memory Required by OS bytes Not Set by OS Memory HVERSION SVERSION 0x0710 Ox0900 D 28 5a b 4a b 5a b 4a b Oa b la b 3a b la b 3a b 20L3205392 ZOILSZO5992 Displaying the Status of the System I O The IO command lets you identify all built in I O devices and option al I O devices installed in the option slots It is available in the In f
105. g the Operating System 5 4 5 3 Problems with the 802 3 Network 5 5 5 4 Problems Using a Hard Disk Drive 5 6 5 5 Problems Using the CD ROM Drive 5 7 5 6 Problems Using the DDS Tape Drive 5 8 5 7 Problems Using the Floppy Disk Drive 5 9 Col SCS Bus DitterenceS 3 wotc 5 bie dsb a beset ats at C 4 C 2 SCSI Bus Addresses ID Numbers and Arbitration Priorities 0 cece eee ee eee C 5 C 3 Narrow Single Ended SCSI Bus Configuration Constraints C 9 C 4 Fast Wide SCSI Bus Configuration Constraints C 10 C 5 Ultra Wide SE SCSI Bus Configuration Constans 3 440750 ee a ek tick Wiese Pa de es hee eee C 10 C 6 SCSI Bus Length Worksheet for Narrow Single Ended SCSL BUS osu cvediwee aE a cadet teats C 13 C 7 SCSI Bus Length Worksheet for Fast Wide SCS BUS 458564 446 340 beh Eh es eee Seek Meera d C 15 C 8 SCSI Bus Length Worksheet for Ultra Wide SE SC SL BUSS tice eae Pots be che hE ROL O Ob a oe iste a C 17 C 9 Narrow Single Ended SCSI Device IDs C 22 C 10 Fast Wide SCSI Device IDs C 24 C 11 Ultra Wide SE SCSI Device IDs C 25 Det sSystem Pans viens ode ta BORE s CREE Ow ee en dew ee D 14 D 2 Mnemonic Style Notation 0 000000 0 0 D 14 xi xii Preface xiii This owner s guide describes how to use
106. hat sam listed as sup porting compression Restoring Files from a Data Cassette to Your System Use the following instructions to restore files from a data cassette to your system 1 Load the data cassette into the tape drive 2 Inaterminal window use ed to change to the directory in which you want the files to reside 3 Enter the following command line tar xvf dev rmt devicefile pathname 3 15 3 16 where devicefile is one of the device files listed from sam and pathname is the pathname of the file or directory containing files that you want to restore from the tape If pathname is not speci fied everything on the data cassette is restored To use the data compression mode use one of the device file names that sam listed as supporting compression Listing the Files on a Data Cassette Use the following instructions to list the files on a data cassette 1 Load the data cassette into the tape drive 2 Inaterminal window enter the following command line to re ceive a file listing of the data cassette tar tvf dev rmt devicefile where devicefile is one of the device files listed from sam If the tape was made with data compression use on the the device file names that sam listed as supporting compression 3 17 The man utility looks up man pages on the sys tem 3 18 Further Comman
107. he Console to External Terminal In the event that your console stops displaying to your graphics de vice use the following procedure to display the console to an external terminal 1 Turn system power off 2 Disconnect the PC keyboard connector from the system rear panel 3 Connect a serial terminal to the Serial 1 connector the left serial connector on the system rear panel PCI EISA as sembly 4 Power on the system The system will now display the console to the terminal connected to the Serial 1 port D 23 Displaying the Current Memory Configuration D 24 The following sample screen output using the memory command shows first a memory configuration table with properly installed and configured memory Sample Output 1 and second output when a DIMM has been improperly installed Sample Output 2 To display the current memory configuration for your system from the Information Menu of the boot console interface follow the direc tions in Accessing the Boot Console Interface earlier in this appen dix Once you are in the Boot Console Interface Main Menu type Main Menu Enter command gt information This places you in the Information Menu From here type Information Menu Enter command gt memory The screen displays status and configuration information for the memory DIMMs installed in your workstation The first listing below shows the memory information for a system with correctly installed
108. he mouse cursor into the terminal window and single click the left mouse button 3 Enter the following at the prompt usr sbin ioscan f After a few moments the ioscan utility lists all of the SCSI I O devices it could find The list appears similar to the following B 4 Class H W Path Driver S W State H W Type Description be 0 root CLAIMED BUS_NEXUS be 1 8 ccio CLAIMED BUS_NEXUS I O Adapter ext_bus O 8 0 c720 CLAIMED NTERFACE GSC built in Fast Wide SCS nterface target O 8 0 0 CGC CLAIMED DEVICE disk 3 8 0 0 0 sdisk CLAIMED DEVICE QUANTUM LPS1080WD target 1 8 0 5 tgt CLAIMED DEVICE disk 2 8 0 5 0 sdisk CLAIMED DEVICE DEC DSP3210SW target 2 8 0 6 tgt CLAIMED DEVICE disk 0 8 0 6 0 sdisk CLAIMED DEVICE DEC DSP3210SW ba O 8 12 bus_adapter CLAIMED BUS_NEXUS Core I O Adapter ext_bus 2 8 12 70 CentIf CLAIMED NTERFACE Built in Parallel Interface audio O 8 12 1 audio CLAIMED NTERFACE Built in Audio tty O 8 12 4 asio0 CLAIMED NTERFACE Built in RS 232C ext_bus 1 8712 5 c700 CLAIMED NTERFACE Built in SCSI target 3 87 12 52 COL CLAIMED DEVICE disk 8 12 5 2 sdisk CLAIMED DEVICE TOSHIBA CD ROM XM 4101TA target 4
109. hese procedures for using your floppy disk drive see Chapter 5 of this book Solving Problems Ordering Information To order Hewlett Packard micro flexible diskettes for use in your 3 5 inch floppy disk drive use the following order number HP 92192X High Density Micro Flexible Disks 1 44MB Formatted Capacity box of ten diskettes Chapter 5 Solving Problems Common problems and solutions Dealing with a boot failure Memory failures LCD indicated problems Running system verification tests 5 2 This chapter contains information to help you determine what s wrong with your system when you have problems If you have a problem that isn t listed in this chapter or if your problem persists contact your designated service representative When calling for ser vice always have your system s model number and serial number ready The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 graphical interface If your system is configured with the HP CDE graphical user interface use command line options in a terminal win dow to perform tests NOTICE The J282 2240 power supply draws about 50 Watts in standby mode system off and will turn on a fan when required to cool the supply NOTICE The J282 2240 fan failure circuitry requires that the power cord must be disconnected for 30 seconds after any f
110. hown in Figure 3 2 NOTICE The write protect tab should always be in the write position for transferring data to a cassette Operating the This section describes how to perform tasks with your DDS tape DDS Tape Drive drive Loading and Unloading a Data Cassette Follow these steps to load and unload a data cassette in the DDS tape drive 1 Turn on power to the tape drive 2 Insert the data cassette into the drive as shown in Figure 3 3 f Up on ee Figure 3 3 Loading a Data Cassette 3 10 3 Push the data cassette about three quarters of the way into the drive The drive automatically pulls the data cassette the rest of the way in When the LEDs on the front of the drive stop flash ing the drive has loaded the data cassette 4 To remove the data cassette press and release the eject button on the front of the drive as shown in Figure 3 3 The LEDs on the drive flash on and off Ten to twenty seconds later the data cas sette slides partway out of the drive Remove the cassette from the drive Verifying the DDS Tape Drive Operation Type the following usr sbin ioscan d stape After a few moments the ioscan utility returns a message similar to the following H W Path Class Description be 8 bc I O Adapter 87 12 ba Core I O Adapter 8
111. ide SCSLIDS a4 046 4gcid ode dw ho ote ho ees C 24 Ultra Wide SE SCSI IDs 0 0 0 0 C 25 Connecting to the SCSI Ports 0 00000 aes C 26 System SCSI Port Connection 0005 C 26 The Boot Console Interface Boot Console Interface Features 0 0 0 eee ee eee D 2 Accessing the Boot Console Interface 00008 D 7 Booting Your Workstation 0 0 cece cece eee eee eens D 9 Searching for Bootable Media 0 cece eee eee ee D 12 Resetting Your Workstation 0 cece eee eee eens D 13 Displaying and Setting Paths 0 0 cece eee eee D 14 Displaying and Setting the Monitor Type D 16 Ihe Monitor Command 2 14 0ei0dbe4 wees be See beech a ee D 16 Displaying the Current Monitor Configuration D 18 Setting the Monitor ype siserekordi rar ES andes seas D 19 Setting the Monitor Type at Power On 002008 D 22 Displaying the Current Memory Configuration D 24 Displaying the Status of the System I O 0 2 08 D 29 Setting the Auto Boot and Auto Search Flags D 31 vii Glossary Index viii Displaying and Setting the Security Mode D 33 Displaying and Setting the Fastboot Mode D 34 Displaying the LAN Station Address 20000 D 35 Displaying System Information
112. ified the following message is displayed LLALA YYYY lt line 1 Selftest Sys Bd lt line 2 Window 3 After the pdh is verified the selftest is executed The display changes to y lt line 1 flashes with Z Y field change lt line 2 Window 4 When the selftest is complete the message once the console is found is LLLL YYYY CPUXX lt line 1 W flashes with Z Y field change AAAAAAAA console lt line 2 where AAAAAA is RS 232A RS 232B or GRAPHICS 5 13 5 14 Window 5 When an attempt to boot is made the following message is displayed once IPL is successfully loaded and launched LLLL YYYY CPUXX Y lt line 1 flashes with Z Y field change BBBBBBBBBBBBBBBB lt line 2 where BBBBBBBBBBBBBBBB is the model number for example 9000 J200 If the system encounters an FLT code while the system is booting the FLT code is interpreted and a messages is displayed For the meaning of the fault code see the J Class Service Handbook Running System Verification Tests HP UX uses a diagnostics product called the Support Tools Manager that allows system operation verification You can access the Support Tools Manager in a terminal window If you are using HP VUE as your interface you can also access the Sup port Tools Manager through the sys_admin directory Th
113. instructions to restore files from a floppy diskette to your system 1 2 Load the floppy diskette into the disk drive In a terminal window use the cd command to change to the di rectory you want the files to reside in cd directory_path where directory_path is the pathname of the directory Enter the following command line 4 9 The man utility looks up man pages on the sys tem 4 10 tar xvf devicefile pathname where devicefile is the device file as listed by sam and pathname is the pathname of the file or directory containing files that you want to restore from the diskette If you do not specify path name everything on the floppy diskette is restored Listing the Files on a Floppy Diskette Use the following instructions to list the files on a floppy diskette 1 Load the floppy diskette into the disk drive 2 Inaterminal window enter the following command line tar tvf devicefile where devicefile is the device file as listed by sam All files on the floppy diskette are listed For More Information For more information on using tar and a complete list of the com mand arguments refer to the tar man page by typing the following in a terminal window man tar You can mount the floppy drive as a file system using the SAM util ity Be sure to unmount the drive before removing it
114. iskless workstation A audience xv audio features 1 13 specifications 1 14 audio connectors headphones OUT 1 12 microphone IN 1 12 boot console interface D 1 booting the system failure See solving problems C CD ROM discs care of 2 5 loading 2 6 2 14 overview 2 5 2 6 unloading 2 9 2 14 CD ROM drive 2 1 busy light 2 19 2 20 controls and features 2 3 2 4 installing in system unit B 16 B 17 jumper settings B 17 loading and unloading a disc 2 6 2 14 mounting and unmounting a disc 2 15 2 20 Index operating controls and features 2 4 overview 2 3 2 4 troubleshooting 2 20 verifying the configuration 2 11 closing the system unit B 8 B 9 commands cpio 3 18 4 10 cstm 5 15 exit 5 17 fbackup 3 18 ftio 3 18ftp 1 23 ioscan 4 5 mediainit 4 8 mt 3 18 rcp 1 23 rlogin 1 22 tar 3 14 4 8 telnet 1 22 verify 5 16 configuring hardware B 1 changing monitor type B 64 closing the system unit B 8 B 9 installing CD ROM drive B 16 B 17 DDS tape drive B 18 B 21 EISA or graphics board B 51 B 63 floppy drive B 22 B 31 hard disk drive B 32 B 35 mass storage devices B 10 B 28 memory B 38 B 45 opening the system unit B 6 B 7 connectors system unit ac power 1 16 audio headphones OUT 1 12 audio microphone IN 1 12 Index 1 keyboard 1 14 mouse 1 14 network 1 15 parallel 1 15 PS 2 1 14 rear p
115. mation for your worksta tion from either your system administrator or your network adminis trator and note them here IP address subnet mask 1 21 Networking Overview 1 22 Your workstation is capable of many more tasks than are described in this owner s guide This section gives an overview of some of the net working capabilities of your system and directs you to the appropriate source for more information Mail Electronic mail allows you to send and receive mail messages on your workstation For information on setting up and using electronic mail on your workstation contact your system administrator and also see the Using Your HP Workstation manual that came with your worksta tion telnet The telnet application uses the TELNET protocol to communicate with another computer system on the network The telnet application allows you to log on to the remote system from your workstation For more information on telnet read the online man page by entering the following at a command line prompt man telnet rlogin The rlogin application also allows you to log on to another computer system on the network from your workstation For more information on rlogin see the Using Your HP Workstation manual that came with your workstation and read the online man page by entering the fol lowing at a command line prompt man rlogin ftp The ftp application is a user interface to the File Transfer Protocol Use ftp to copy fil
116. mechanical and electrostatic shock When handling the drive always wear the static grounding wrist strap that came in the DDS tape drive kit Always handle the drive carefully If you need to change the DDS tape drive s address or operation mode follow these instructions referring to Figure B 9 for the DDS DC drive Figure B 10 for the DDS 2 drive and Figure B 11 for operation mode If you do not need to change the drive s address or operation mode go to Step 10 of this installa tion procedure l 2 Locate the jumpers at the back of the DDS tape drive To change the jumper settings use needlenose pliers to set the drive s SCSI ID to an address that is not used by another SCSI device Check that the other jumpers are set correctly NOTICE Do not use SCSI ID 7 for your DDS tape drive s SCSI address The host SCSI controller uses SCSI ID 7 Use needlenose pliers to remove the SCSI terminators 1f still attached to the drive If you need to change the Operation Mode switches locate the switches on the underside of the DDS tape drive Switches 1 and 2 are used to configure the data compression operation mode Switches 3 through 8 are used to specify drive connectivity and functionality according to host or customer requirements The default setting is all switches ON Figure NO TAG shows the available options SCSI Terminators must be removed Target Term Jumpers Target Term J
117. min Move the mouse cursor to the SAM icon shown below your icon can look like either of these and double click the left mouse button The System Administration Manager window opens Double click on Peripheral Devices gt The Peripheral Devices window opens Double click on Disks and File Systems gt The Disks and File Systems window opens Double click on CD ROM Floppy and Hard Disks The following screen message appears Scanning the system s hardware The CD ROM Floppy and Hard Disks window opens con taining a list of drives currently configured on this system 9 From the Actions menu click on Add a Hard Disk Drive 10 The Select a Disk to Add window opens with a list of unused disks Highlight the hard disk drive you want to add to your sys tem 11 Click on coe 12 The Set Disk Usage and Options window opens Select File System and click onL_ok__ 13 The following screen messages appear Task started Creating the device file Modifying etc checklist Task completed Click on cK B 37 Installing Take a moment to read over the following important notes about Additional installing memory Memory Before trying to install additional memory DIMMs in your J282 2240 workstation use the procedure described in Appendix D The Boot Console Interface to determine the current memory configuration for this workstation Read over the steps involved
118. n nector on both ends The last device connected to the SCSI bus must be terminated with a SCSI terminator All of the devices listed ship without terminators If you do not already have a SCSI terminator you must order terminator K2291 for 50 pin connectors or C2905A for 68 pin fast wide dif ferential connectors or C2972A for 68 pin ultra wide SE connec tors from Hewlett Packard SCSI Configuration Constraints You are limited to a certain number of same type SCSI devices per system Before adding another SCSI device determine if the system can support the additional device This workstation offers the following types of SCSI bus each with its own configuration constraints narrow single ended SCSI bus fast wide differential SCSI bus J282 or J2240 upgrade ultra wide single ended SCSI bus J2240 only Narrow Single Ended SCSI Bus Configuration Constraints For the narrow single ended SCSI bus HP UX supports only one of each type of removable disk drive and two of the same type tape de vices per system Table C 3 shows configuration constraints for each narrow single ended SCSI device type If the system has internal hard disk drives or a floppy disk drive you must count them as SCSI devices Table C 3 Narrow Single Ended SCSI Bus Configuration Constraints Maximum Number of Each Narrow Single Ended SCSI Devices Type of Device Allowed Hard Disk Drives internal a
119. n a typical Hewlett Packard workstation configuration Exeter Cue 20 1990 Date James Kelly Quality and Engineering Manager European Contact Your local Hewlett Packard Sales and Service Office or Hewlett Packard GmbH Department ZQ Standards Europe Herrenberger Strasse 130 D 71034 Boeblingen FAX 49 7031 143143 Emissions Regulations Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules and the Canadian Department of Communications These limits are de signed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception determined by turning the equipment off and on you can correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Ask the dealer or an experienced radio television
120. nd external 7 Floppy Disk Drives l CD ROM Drives 1 4 mm DDS Tape Drives one internal 2 9 track Tape Drives 2 650 MB Magneto Optical Drives 1 Magneto Optical Autochangers see notice below 1 Maximum Number of SCSI Devices 7 NOTICE Magneto Optical Autochangers use three SCSI 2 drive addresses Each address must be accounted for in the maximum number of NSE SCSI devices allowed CAUTION Do not mix narrow single ended ultra wide SE and fast wide differential SCSI peripherals together on the same bus Fast Wide Differential SCSI Bus Configuration Constraints Fast wide differential SCSI does not work with the narrow single en ded SCSI Table C 4 shows the configuration constraints for each fast wide differential SCSI device type Table C 4 Fast Wide Differential SCSI Bus Configuration Constraints Maximum Number of Each External Fast Wide Differential SCSI Devices Type of Device Allowed SCSI 3 Drive fast wide disk drives only 15 SCSI 3 Disk Arrays addressed as single drive 7 CAUTION Do not mix narrow single ended ultra wide SE and fast wide differential SCSI peripherals together on the same bus Ultra Wide Single Ended SCSI Bus Configuration Constraints Ultra wide SE SCSI does not work with the narrow single ended SCSI or FWD SCSI Table C 5 shows the configuration constraints for each ultra wide SE S
121. nder the heading Device ID Number Add your new drive to the table if it is an external device If it is an internal drive continue to Step 4 NOTICE The C1700A Magneto Optical Autochanger 4 uses three SCSI addresses and accounts for three of the seven devices allowed on the SCSI bus Check to see which SCSI device IDs are not used You can use ID numbers 0 through 6 if they are not already in use If the de fault ID on your drive does not conflict with any existing drive IDs use that ID If your default address conflicts with an exist ing drive ID you need to assign a new SCSI device ID to your drive See the drive installation documentation for information on changing the device ID CAUTION Do not use SCSI device ID 7 for any device except the system card C 21 Table C 9 Narrow Single Ended SCSI Device IDs Device ID Address Number Only 0 through 6 Available SCSI Device Drives Internal External Internal System Drives System SCSI Drive s Floppy Disk Drive if present uses ID No 0 N A CD ROM Drive if present uses ID No 2 N A 4 mm DDS Tape Drive if present uses ID No 1 N A External Device Drives Ist External Device N A 2nd External Device N A 3rd External Device N A 4th External Device N A Sth External Device N A 6th External Device N A N A 7th External Device N
122. ng With a Boot Failure later in this chapter If problems persist contact your system administrator or call your designated service representative Table 5 5 Problems Using the CD ROM Drive Problem Solution The CD ROM drive does not respond to commands Re enter the commands and make sure that you have typed them cor rectly Make sure that the system can com municate with the drive as described in Checking the SCSI IDs in Appendix B Follow the instructions in the section entitled Running System Verifica tion Tests later in this chapter to verify that the CD ROM drive is functioning properly If problems persist contact your system administrator or call your designated service representative 5 7 5 8 Table 5 6 Problems Using the DDS Tape Drive Problem Solution The DDS tape drive Re enter the commands and make sure does not respond to that you have typed them correctly commands Make sure that you specified the cor rect device file name for commands that require a device file name Make sure the write protect tab is set to write if you are trying to copy data to a data cassette Make sure that the system can com municate with the drive as described in Checking the SCSI IDs in Ap pendix B Follow the instructions in the section entitled Running System Verification Tests later in this chapter to verify that the tape dri
123. ngs take effect at the next BOot or SEArch command Displaying System Information D 36 The all command allows you to display the system s processor revi sion and speed cache size memory size flag settings and the boot and console paths To display system information from the Informa tion Menu type the following at the prompt Information Menu Enter command gt all This information is paged to allow you to view it as necessary Displaying PIM Information The pim command allows you to display the most recent PIM in formation for the specified fault type To display PIM information for a specific fault from the Service Menu type the following at the prompt Service Menu Enter command gt pim processor_number You can use pim in the following ways pim gives all fault types pim 0 HPMC information on processor pim 0 fault_type fault type information on processor D 37 Glossary absolute pathname The full pathname of a file including all the directories leading to it starting with the root directory and ending with the filename it self See also file filename pathname access permissions Settings that allow a user or group of users to read write or execute files See also file access permissions active window The window that is receiving input from the keyboard at the present time If there is no active window anything you type is lost Only one window
124. o you want to remove the disk Click on L__yes___ The system reboots Press the eject button on the CD ROM drive and remove the CD ROM disc from the disc tray Reading the Busy Light The CD ROM busy light shows the status of the drive during the self test and during activity with the host system The CD ROM drive performs the self test when one of the following happens You load a disc and close the Disc Tray You turn on the workstation with a disc already loaded in the CD ROM drive For the self test the busy light operates in the following sequence 1 Light On The busy light goes on when the disc loads into the drive 2 Light Flashing The light flashes six times while a read test is performed on the disc 3 Light Off The light goes off when the self test is com plete The busy light stays on after the self test when one of the following conditions exist A defective disc A disc insertion error for example an upside down disc No disc present The busy light goes off when one of the following conditions exist A CD ROM drive power failure exists The drive is idle on the SCSI bus The busy light flashes during normal activity with the system 2 19 Troubleshooting If you have trouble with any of these procedures for using your CD ROM drive see Chapter 5 of this book Solving Problems 2 20 Chapter 3 Using Your DDS Tape Drive
125. of access permissions a code that determines whether a process can perform a requested operation on the file such as opening the file or writing to it See also access permissions File Manager The HP VUE application that allows you to manage your files and directories and to set viewing preferences filename The name given to a particular file See also absolute pathname file pathname file server A workstation whose primary task is to control the storage and re trieval of data from hard disks Any number of other workstations can be linked to the file server in order to use it to access data GL 9 GL 10 file system The organized set of files and directories on a hard disk floppy diskette A thin record shaped plate that stores data on its magnetic surfaces The system uses heads similar to heads in tape recorders to read and write data on concentric disk tracks floppy drive A device that stores data on a flexible diskette hard disk A type of disk that is rigid as opposed to a floppy diskette which is flexible hard disk drive A device that stores data on a hard disk The hard disk is a permanent part of the drive and cannot be removed Help Manager The HP VUE application that provides online help HOME The environment variable representing the home directory This is the directory in which you are placed after you log in Typically this is users login where login is your username
126. ointer on the screen See also drop drive See CD ROM drive DDS tape drive floppy drive hard disk drive drop To release an icon that has been dragged to a new position See also drag environment The conditions under which your commands are executed These conditions include your workstation characteristics home directory and default search paths See also environment variables environment variables The set of defined shell variables some of which are PATH TERM SHELL EXINIT HOME that define the conditions under which your commands are executed These conditions include your worksta tion characteristics home directory and default search paths See also environment ETHERNET The LAN developed jointly by Digital Equipment Corporation Intel and Xerox Corporation upon which the IEEE 802 3 network is based Extended Industry Standard Architecture EISA An industry standard bus architecture based on and compatible with that used by IBM in their AT series computers fast wide SCSI A 16 bit wide bus with high power receivers and drivers which al lows a cable length of up to 25 meters and a speed of up to 20 MB per second See also single ended standard SCSI Small Computer System Interface file The basic named unit of data stored on disk See also directory file name file access permissions The access rights given to a particular file or directory Every file and directory has a set
127. ompt return of the product 4 HP products may contain remanufactured parts equivalent to new in performance or may have been subject to incidental use 5 The warranty period begins on the date of delivery or on the date of installation if installed by HP If customer schedules or delays HP installation more than 30 days after delivery warranty begins on the 31st day from delivery 6 Warranty does not apply to defects resulting from a improper or inadequate maintenance or calibration b software interfacing parts or supplies not supplied by HP c unauthorized modification or misuse d operation outside of the published environmental specifications for the product or e improper site preparation or maintenance 7 TO THE EXTENT ALLOWED BY LOCAL LAW THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE 8 HP will be liable for damage to tangible property per incident up to the greater of 300 000 or the actual amount paid for the product that is the subject of the claim and for damages for bodily injury or death to the extent that all such damages are determined by a court of competent jurisdiction to have been directly caused by a defective HP product 9 TO THE EXTENT ALLOWED BY LOCAL LAW THE REMEDIES IN THIS WARRANTY STATEMENT ARE
128. on your system using Table C 7 1 2 List all of your internal FWD SCSI devices in the first column In the second column write the lengths of the internal FWD SCSI bus that correspond to your devices In the third column write down the lengths of the FWD SCSI interconnect cables you are using for your installation Cable lengths are listed in subsection Cables in the SCSI Restric tions section Add up all of the numbers in the second column and write that number on the subtotal line at the bottom of the column Do the same for the third column Add the subtotals together and write the total in the Total FWD SCSI Bus Length box NOTICE The total length of the FWD SCSI bus must not exceed 25 meters 82 feet If the number you write for Total FWD SCSI Bus Length is greater than 25 meters 82 feet try configuring your installation with shorter cables If you have problems call your designated service representative Table C 7 SCSI Bus Length Worksheet for Fast Wide Differential SCSI Bus FWD SCSI Device Internal FWD SCSI Bus Length meters feet Device Internal Length meters feet External Cable Length meters feet System Unit C3034T C3035T C3036T 1 7 5 6 1 0 3 3 1 0 3 3 1 0 3 3 N A Subtotals Total FWD SCSI Bus Length Total FWD SCSI bus length not to exceed total of 25 meters 82 feet C 15 Ultra Wid
129. ormation Menu To use the IO command from the Information Menu of the boot con sole interface type Information Menu Enter command gt IO Information about the built in and optional I O devices is displayed I O MODULE INFORMATION IODC IODC Path Decimal Type Location HVER SVER Vers Dep 8 0 8 0 Bus Bridge built in 6800 0a00 0x00 0x00 FWSCSI 8 12 A DMA I O built in 03b0 8980 0x96 0x00 8 16 8 16 Bus Adapter built in 03b0 8100 0x00 0x00 8 16 0 8 16 0 Parallel built in 03b0 7400 0x00 0x00 8 16 1 8 16 1 Audio built in 03b4 7b00 0x00 0x00 SERIAL_1 8 16 4 RS232 built in 03b0 8c00 0x01 0x00 SESCSI 8 16 5 SE SCSI built in 03b0 8200 0x96 0x00 LAN 8 16 6 LAN p built in O0O3b0 8a00 0x02 0x00 PS2 8 16 7 Keyboard built in 03b0 8400 0x00 0x00 8 16 8 8 16 8 Mouse built in 03b0 8400 0x00 0x00 D 29 D 30 8 16 10 8 16 10 Floppy built in O03b0 8300 8 20 8 20 SERIAL_2 8 20 2 RS232 Port built in EISA 8 20 5 GRAPHICS 0 0x00 9 63 8763 Bus Adapter built in 0170 8e00 Bus Converter built in 5011 O0c00 10 63 10 63 Bus Converter built in 5011 0c0o0 EISA Cards Path 8 20 5 1 8 20 5372 S 20 75 3 PCI Cards Slot Path Type EISA EISA EISA Bus EISA slot is slot is slot is Class 0x00 0x00 0170 8c00 0x00 Bus Adapter built in 0170 9000 0x00 8 24 INTERNAL_EG_X128 built in 0160 8500 0x00 0x00 ID empty empty empty 0x00 0x00 0x00 0x00 0x01
130. ors on the system unit s Rear Panel rear panel Connectors Audio connectors including headphones and microphone PS 2 keyboard and mouse connectors HP parallel Centronics I O connector 802 3 AUI LAN connector 802 3 TP Twisted Pair LAN connector RS 232C serial I O connectors SCSI connectors including fast wide differential or ultra wide SE J2240 only and narrow single ended SCSI TOC button Power cord connector HP HIL connector J282 only NOTICE To maintain FCC EMI compliance verify that all cables are fully seated and properly fastened Figure 1 4 shows the locations of the connectors on the system unit s rear panel a Fast Wide Differen ast Wide Differen Connectors tial or Ultra Wide gt gt SE SCSI Connector Narrow SE SCSI Se a Connector ae A A TOC _ Hy Button e Te ty Keyboard not shown Pe g Connector Mouse lt Connector S Si AUI LAN S lt Connector R Ui lt Twisted Pair Connector S N labeled UTP RS 232C l D Connectors lt HP HIL A D SS Connector cS J282 only SES SCSI Connectors are Power shown with terminators Connecior attached as they are shipped from the factory See Figure 1 5 for detail Connector lt Graphics
131. our workstation Displaying and setting paths Displaying and setting the monitor type Displaying the current memory configuration Displaying the status of the System I O Setting the Auto Boot and Auto Search flags Displaying and setting the Security mode Displaying and setting the Fastboot mode Displaying the LAN station address Displaying system information Displaying PIM information Boot Console Interface Features There are times when you want to interact directly with the hardware of your workstation before it boots the operating system Your workstation provides a menu driven boot console interface that al lows you to perform special tasks display information and set certain system parameters even if the operating system is unavailable Here are some of the things you can do Boot your workstation Search for bootable media Reset your workstation Display and set boot paths Display and set your monitor type Display memory configuration information Display the status of the EISA slots Set Auto Boot and Auto Search Set Fastboot Display LAN information Display system information Display PIM information NOTICE All of the tasks in the boot console interface should be performed by a system administrator The boot console menus follow showing the various tasks you can perform and the information available The shortened version of all commands is indicated by the uppercase letters Help is availabl
132. ppendix and then type the following command at the prompt Main Menu Enter command gt boot sescsi 1 0 D 9 If you do not know which device you want to boot from then type the following at the prompt Main Menu Enter command gt search Path Number Device Path Device Type PO FWSCS1 6 40 HP C2490WD Pl SE CoLa LeU HP HP35480A Main Menu Enter command gt Boot P1 The operating system on the specified device is used to start your workstation also see Searching for Bootable Media Ifyou wish to interact with the Initial System Loader ISL be fore booting your workstation follow the directions in Acces sing the Boot Console Interface earlier in this appendix and then type the following at the prompt Main Menu Enter command gt boot device You are prompted Interact with ISL Y N Q gt Answering yes Y causes the ISL to be loaded from the specified device After a short time the following prompt appears on your screen ISL gt ISL is the program that actually controls the loading of the operating system By interacting with ISL you can choose to load an alternate version of the HP UX operating system If you do not want ISL to be loaded you must enter N For example if the usual kernel stand vmunix on your root disk fwscsi 6 0 has become corrupted and you wish to boot your workstation from the backup kernel stand vmunix prev type the following at the ISL gt prompt ISL gt hpux
133. pport Wave 5 17 fbackup command DDS format tape drive 3 18 File Transfer Protocol See ftp command floppy disk drive 4 1 configuring the floppy driver 4 12 formatting a diskette 4 8 4 12 inserting and removing a diskette 4 4 troubleshooting 4 12 using device files 4 6 verifying the configuration 4 5 4 12 write protecting a diskette 4 3 4 4 floppy diskette archiving data 4 8 4 12 formatting 4 8 4 12 listing files 4 10 restoring files to system 4 9 4 10 saving files 4 9 transferring data 4 8 4 12 write protect tab 4 3 4 4 floppy drive installing in system unit B 22 B 31 jumper settings B 23 terminators B 24 ftio command DDS format tape drive 3 18 ftp command 1 23 H hard drive adding B 35 B 37 attaching mounting bracket B 31 configuring B 35 installing in system unit B 32 B 35 jumper settings B 30 hardware configuration See configuring hardware important information 1 20 1 21 indicators LCD system unit 1 7 LED CD ROM drive 2 19 2 20 DDS 2 tape drive 3 6 3 8 DDS DC tape drive 3 4 3 8 removable device 1 8 system unit 1 8 installing hardwareCD ROM drive B 16 B 17DDS tape drive B 18 B 21EISA or graphics board B 51 B 63floppy drive B 22 B 31hard disk drive B 32 B 35mass storage devices B 10 B 28 introduction See system overview ioscan command floppy disk drive 4 5 IP address information
134. ption dialog box A special type of HP VUE screen that is called by the user from a window Dialog boxes contain controls and settings To display an example of a dialog box click the Style Manager button on the Work space then click on Color directory A special type of object that contains information about the objects beneath it in the HP UX organizational structure Basically it is a file that stores names and links to files and other directories See also file disk A thin round plate with a magnetic surface coating on which data is stored by magnetic recording See also floppy diskette hard disk CD ROM disc disked workstation A workstation that has its own hard disk drive See also diskless workstation node partner node workstation diskette See floppy diskette diskless booting Loading the operating system into local memory from the disk of a partner workstation diskless workstation A workstation that has no disk A diskless workstation can use the disk of its partner workstation or other workstations If necessary it can also use the computational services of the partner workstation or other workstations A diskless workstation boots from its partner workstation See also disked workstation node partner node workstation GL 7 GL 8 double click To press and release a mouse button twice in rapid succession drag To press and hold down a mouse button while moving the mouse and the p
135. rack which is read they store computer data at a constant speed You may access files and data stored on a CD ROM disc but you may not write files or data to a CD ROM disc CAUTION Handle CD ROM discs by the edges only Al ways be sure a CD ROM disc is either in the CD ROM drive or its protective case when not in use This will lessen the chance of exposing the disc surface to dust Over time dust reduces the reliability of the read head in the CD ROM drive Caring for CD ROM Discs Observe the following guidelines to help prevent data loss and pro long the life of your CD ROM discs and drive Use CD ROM discs in a clean environment to prevent dust par ticles from scratching disc surfaces Store CD ROM discs in a cool dry place to prevent moisture and heat damage Don t try to clean the surface of a CD ROM disc with cleaning solvents as some cleaning solvents may damage the disc NOTICE You must mount the disc after loading it into the drive Refer to the section Mounting and Unmounting a CD ROM Disc later in this chapter for instructions 2 5 Operating the CD ROM Drive 2 6 This section describes how to perform tasks with your CD ROM drive Loading and Unloading a CD ROM Disc This section describes how to load or unload a CD ROM disc Loading a CD ROM
136. rder Pair 1 OA OB Pair 2 1A 1B Pair 3 2A 2B and so on This workstation has 16 memory slots labeled OA OB through 7A 7B Memory DIMMs must be installed in pairs of equal size with the largest pairs installed first followed in order from larg est to smallest pairs Figure B 24 gives the recommended order for installing pairs of DIMMs Any Combination of memory may be used although for maxi mum performance we recommend using common sized memory DIMMs for example either all 128 MB 256 MB or 512 MB DIMM pairs Therefore to achieve both maximum performance B 41 Pair 8 Pair 6 Front of System gt Pair 7 Pair 5 p 7B 7A 5B 5A 6B 6A 4B 4A and maximum future capacity use 512 MB DIMM pairs exclu sively J18 O oo0o0o0o0o0o0 0000 000000 000000000000000000 oo00o0o0o0e00000 000000 eCo00o0c0oO0O0 0000000 0 Of 3a 7 J17 O o0o0000000000000000 Oo00000000000 000000 O oo0o00000 0000000000 C0O0000000000000 0 0B J16 O oo0o0o0o0000000 000000 oo0o00000000 00000000 O oo0o000000 0000000000 o00000000000000 0 0G J15 O ORDO DOO DOO OOOO E S oo0o0o0o000o0 0000000000 ooo0o000000000 000000 eoo0o00o00O0O0O0000 0000 0 J31 O ROO ER S O Gy o0o0000000000000000 oo0o0o000000000 000000 o0o0000000000000000 J30 O T D OA S OOR O Ona D E rOn es oo oo ooo oo coo OOO OO 8 oo0o0o0o0o0cC0oO0cC0cC
137. ree interfaces are available with the Support Tools Manager a command line interface accessed through the cstm command a menu driven interface accessed through the mstm command and the graphical user interface accessed through the xstm command For more information on these user interfaces see the online man pages by entering the following at a command line prompt man cstm man mstm man xstm To access the Support Tools Manager perform the following steps 1 Click on the Terminal Control on the Front Panel of your Workspace Terminal Control 5 15 A terminal window opens 2 Move the mouse cursor into the terminal window and click the left mouse button 3 Enter the following at the prompt cstm The following screen appears Support Tool Manager Version A 01 00 Type help for a list of available commands CSTM gt At the CSTM gt prompt you can enter several commands To see what commands are available type the help command 4 To verify the system operation type the following at the cSTM gt prompt CSTM gt verify all Messages similar to the following appear Verification has started on device CPU Verification has started on device FPU CSTM gt Verification of FPU has completed CSTM gt Verification of CPU has completed 5 Press to return to the CSTM gt prompt after all test results are reported 5 16 6 To exit the Support Tools Manager type the follo
138. s and Solutions 00005 5 3 Dealing with a Boot Failure 0 0 0 0 cece eee 5 10 Memory PallureS 433439 noi beak ke Gud ca EN eae 5 11 LCD Indicated Problems 0 0 0 e eee eee 5 12 Running System Verification Tests 2 0 cece eee 5 15 Appendix A Appendix B VI Safety and Regulatory Statements Declaration of Conformity 0 0 0 0 cece eens A 2 Federal Communications Commission FCC A 3 Emissions Regulations 0000 cc cee eee A 3 NCCT Cle 2 ITE vc 5 aah hewlett wh BR pda eae 6 A 4 Emissions Regulations Compliance 0000085 A 4 Datacom Users Statement United Kingdom Only A 4 Regulation On Noise Declaration For Machines 3 GSGV A 4 PX COWS CS oie rg a 8 E Bk when rade ese Als oe eesin eave abe ee A 4 Electrostatic Discharge ESD Precautions A 5 Laser Safety Statement For U S A Only A 6 IEC 825 Class 1 Laser Label 1 4 kcu ee ack eed 84 dkw a ee A 6 Warnings and Cautions 00 0 A 7 Changing Your Workstation s Hardware Configuration Checkine the SCSLIDS 2 i0 see jot po a a ae haloes deca B 3 Opening the System UM 6 524054 intan a bed aca B 6 Closing the System Unit iiie 4402 eriei oh do de ere de B 8 Installing Removable Media Devices 04 B 10 CD ROM Drive serores oda tae cone Uo Ele odes ee B 16 DDS Tape Dieser tet etlwecee eu eer ee cts
139. s by a user program GL 21 GL 22 system name See internet protocol address terminal window A terminal window is a type of HP VUE window that emulates a complete display terminal Terminal windows are typically used to fool non client programs into believing they are running in their fa vorite terminal When not running programs or executing operating system commands terminal windows display the command line prompt See also HP Visual User Environment title bar The rectangular area between the top of the window and the window frame that contains the title of the window object transceiver A device that transmits and receives signals user account The system administrator defines a user account for every person au thorized to use the system Each user account contains the name the computer uses to identify the person user ID and the person s pass word User accounts also contain project and organization names to help the system determine who can use the system and what resources each person or organization can use See also user ID password user ID The name the computer uses to identify you Your system administra tor assigns you a user ID Enter your user ID during the login proce dure when the system displays the login prompt See also user ac count username The name that the system recognizes as uniquely yours Also known as your login name The username is also the name that identifies you
140. s disabled set to off more extensive memory test ing and I O interface testing is performed during the self tests caus ing the boot process to take longer If you are experiencing difficulty in booting your workstation set fastboot to off and reboot the system The more extensive testing may reveal the error condition To display the status of fastboot type the following at the prompt Configuration Menu Enter command gt fastboot To disable fastboot type the following at the prompt Configuration Menu Enter command gt fastboot off To enable fastboot type the following at the prompt Configuration Menu Enter command gt fastboot on Displaying the LAN Station Address It is sometimes necessary to supply a LAN station address of your workstation to other users For example if your workstation is to be come a member of a cluster the cluster administrator needs to know your LAN station address in order to add your workstation to the cluster A LAN station address of your workstation is the label that uniquely identifies the LAN connection for your workstation at the link level the hardware level To display your workstation s LAN station addresses type the follow ing at the prompt Information Menu Enter command gt lanaddress The LAN station address is displayed as a twelve digit number in hexadecimal notation similar to the following LAN Station Addresses O80009 789abc The address is for the syst
141. s shipped with Grasp the module and pull the dust cover evenly to remove 9 Install the processor by aligning the plastic guide rails on the shroud with the rails on the processor firmly seat module Figure B 29 J282 2240 Processor Modules B 48 10 Insert the board containing the processor module into the guides and press firmly into place 11 Reconnect the fan cable to the system board 12 Replace the CPU shroud over the processor and replace the four screws attaching the CPU shroud to the system board 13 To replace the CPU Assembly in the system unit first align the top of the CPU Assembly with the guide on the system unit Re fer to Figure B 30 and to the label on the back of the assembly Be sure to support the CPU Assembly properly while replacing it roe gt gt s NU M A OR Dw Figure B 30 Replacing the CPU Assembly B 49 B 50 14 15 Next align the bottom of the CPU Assembly with the guide on the system unit With the ejector latches in the open position slide the CPU Assembly into the system unit as far as it will go See Figure B 30 Press the ejector tabs
142. scribe the path of the operating system from some starting point in the network to a destina tion object Pathnames begin with the name of the starting point and include every directory name between the starting point and the des tination object A pathname ends with the name of the destination ob ject See also name object permissions A set of rights read write execute associated with an object in the file system Determines who may use the object PID Process Identification Also referred to as a process ID See also pro cess ID GL 17 GL 18 pointer Sometimes called the mouse pointer the pointer shows the mouse location on the screen The pointer s shape depends on its location In the HP VUE Workspace the pointer is an X On a window frame the pointer is an arrow process A computing environment in which you may execute programs a program currently running in the system process ID A unique identification number assigned to all processes by the oper ating system Also referred to as a PID See also PID program A unit of executable code in binary or source form Most HP UX commands and routines consist of programs prompt A message or symbol displayed by the system to let you know that it is ready for your input push button A graphic control that simulates a real life push button Use the pointer and mouse to push the button and immediately start an action RAM Random
143. signal on the LED indicators If the LED indicators on your DDS format drive display the Media Wear Caution condition follow this procedure 1 Check the system console for any tape error messages A hard error during a read or write operation may have occurred 2 Clean the heads with a cleaning cassette HP92283K as de scribed in the Cleaning the Tape Heads section later in this chapter 3 Repeat the operation you performed when the Media Wear Cau tion signal displayed If the Media Wear Caution signal still displays then the data cassette should be replaced 3 5 4 If you are performing a backup from disk to tape discard the data cassette and back up your files using a new data cassette 5 If you are performing a restore from tape to disk complete the restore then discard the data cassette and back up the files to a new data cassette LEDs DDS 2 The front panel has two colored LEDs the Tape Light and the Clean Attention Light The Tape Light flashes green to show activity load ing unloading reading and writing Steady green means a cartridge is loaded The Clean Attention Light flashes amber to indicate head cleaning is needed or a cartridge is near the end of its life Steady amber means a hard fault Table 3 2 LED Display Codes DDS 2 Drive Tape Clean Meaning Key Light Attention OFF
144. symbol indicates a notice This symbol indicates a procedure This symbol indicates a caution This symbol indicates the end of a chapter or a part of this guide xvii Questions If you have any questions suggestions or problems with our hard Suggestions or ware software or documentation please call 1 800 633 3600 US Problems amp Canada or contact the HP Response Center for your country xviii Chapter 1 System Overview Product description System unit front panel controls LED and LCD System unit rear panel connectors Monitors Keyboard and Mouse Pointing devices Operating system overview Important information you need to note Networking overview 1 1 1 2 This chapter introduces the HP 9000 J282 2240 workstations Its pur pose is to familiarize you with your workstation and its controls and indicators The instructions in this chapter assume you are using the HP UX version 10 20 or later operating system with the HP VUE version 3 0 interface Product Description This workstation has the following key features Operating System User Interface Compatibility Monitors Optional Graphics Main Memory HP UX version 10 20 or later J2240 requires HP UX 10 20 ACE Feb 1998 plus J2240 Hardware Extensions software HP VUE version 3 0 graphical user interface or HP CDE Source and binary code compatible with th
145. t From the Actions menu click on Show Device Files A window opens with a list of the device files for the selected CD ROM drive with an explanation of each one Mounting and Unmounting a CD ROM Disc SAM System Adminis tration Manager is a util ity that performs system administration tasks us ing a windows graphical user interface To access information on a CD ROM disc you must first mount the disc This applies to file system information only If you wish to load a music CD for example you would not need to mount the disc Mounting a disc with file system information on it gives the disc a pathname that allows your workstation to communicate electronically with it You must unmount the CD ROM disc before removing it from the drive CAUTION To use a CD ROM disc as a mounted file sys tem you must mount the CD ROM disc every time you load it into the drive You must also unmount the CD ROM disc every time you unload it from the drive Failure to mount or unmount a disc can cause a system error condi tion and can also require rebooting the system The procedures in this chapter require you to log in as root If you cannot log in as root contact your system administrator Mounting a CD ROM Disc Using SAM Use the following procedure to mount a CD ROM disc 1 Log inas root If you need informa
146. t Be sure to support the drawer from the bottom B 11 Set the drawer on a flat surface 3 Disconnect the power distribution cable from the Fan extender cable 6 Power Extender Power Distribution Cable Figure B 4 Removing FAN from EMI Plate Disconnect the Fan extender cable form the SCSI PCA T B 12 2o 3000000000022 Figure B 5 Removing EMI Plate 8 Remove the two M 3 screws from the fan B 13 B 14 A ir 9 Seas gy 7 nS 2p Sa 22222 f Ee Saso ata CRO OO OO A A r Pa cr rc cr A Pa 5 C C S COE S s QE SE OSE CG SREP HS Oey Figure B 6 Removing FAN EMI Plate 9 Unscrew the captive screw holding the FAN EMI plate at the back of the removable drives and lift the plate up and out of the drawer as shown in Figure B 6 10 Disconnect the SCSI and power cables from the drive 11 Unscrew the two screws holding the drive in the storage drawer and slide the drive out of the drawer See Figure B 7 Figure B 7 Removing Drive Screws 12 Check the SCSI address jumper settings on the replacement drive using the following information sections B 16 CD ROM Drive The CD ROM drive ships with the drive set to SCSI ID address
147. teristics of its functional units More specifically the term configuration may refer to a hardware configu ration or a software configuration control key sequence A keystroke combination used as a shorthand way of specifying com mands To enter a control key sequence you hold down the control key while pressing another key cpu See Central Processing Unit current directory See current working directory GL 5 GL 6 current session The work and processes that have been created since you logged into the system and before you log out again See also session current working directory The directory in which a relative path name search begins as well as the directory in which you are currently working It is also called the working directory or current directory cursor The small blinking box displayed in whatever screen is active at a particular time The cursor marks your current typing position on the screen and indicates which program HP VUE terminal window or shell will receive your commands daisy chaining A method of connecting devices where the signal passes from one device to the next in serial fashion along a bus DDS tape drive A device that stores data on Digital Data Storage DDS cassettes default Most commands give you a choice of one or more options If you don t specify an option the command automatically assigns one This automatic option is called the default See also command o
148. three GSC that can be used as follows two individual EISA one individual GSC and two combination EISA or GSC J2240 one EISA optional three 32 bit PCI two 64 bit PCI and three GSC that can be used as follows one 32 bit PCI one EISA or 32 bit PCI one GSC or 32 bit PCI and two GSC or 64 bit PCI Keyboard PS 2 Keyboard Mouse PS 2 Mouse System Unit Before powering on your system you should become familiar with Front Panel the system unit controls Controls LED and LCD Figure 1 1 shows the the system unit front panel controls System LCD System Power Switch System Power LED Figure 1 1 System Unit Front Panel Controls System LCD The Liquid Crystal Display LCD is located on the left side of the front panel It displays messages about the state of the system includ ing error codes The following symbols appear in the LCD represent ing the different system activities shown nae ms Operating system running Disk Access in progress Network Transmit in progress H Network Receive in progress Figure 1 2 LCD Symbols System Power Switch Use the Power switch to power the system unit on and off CAUTION Do not turn off the power to your workstation without first performing the recommended shutdown procedure If you do not shut down your workstation properly you can damage the programs and data on your
149. tion on logging in or setting up a user account see Using Your HP Workstation 2 Load the CD ROM disc into the disc tray and gently push the tray into the drive 3 Ina terminal window enter the following command sam 4 The System Administration Manager window opens Double click on Peripheral Devices gt 2 15 2 16 9 The Peripheral Devices window opens Double click on Disks and File Systems gt The Disks and File Systems window opens Double click on CD ROM Floppy and Hard Disks The following screen message appears Scanning the system s hardware The CD ROM Floppy and Hard Disks window opens con taining a list of drives currently configured on thie system Disks that are unmounted have the word unused in the Use column From the Actions menu click on Add a Hard Disk Drive The Select a Disk to Add window opens with a list of unused disks Highlight the CD ROM disc you want to mount Giticen 10 The Set Disk Usage and Options window opens Select File System and click on L__ok___ 11 The following screen messages appear Task started Creating the device file Mounting file system Modifying etc checklist Task completed Click on CK Now you can access the CD ROM disc as you would any other mounted file system Unmounting a CD ROM Disc Using SAM Use the following procedure to unmount a CD ROM disc NOTICE Before you unmount a CD ROM disc mak
150. to the mail system and other software requiring secure entry utility See utility program utility program A program provided with the operating system to perform a frequent ly required task such as printing a file or displaying the contents of a directory See also command shell command window A rectangular area of the screen for viewing information HP VUE allows you to create several types of windows on the screen Each window is a separate computing environment in which you may execute programs edit text or read text See also Workspace Man ager Window Manager The HP VUE program that controls the size placement and operation of windows working directory See current working directory Workspace What the screen becomes when you start HP VUE Although you can hide the workspace under terminal windows or other graphic objects you can never position anything behind the workspace All windows and graphic objects appear stacked on the workspace See also HP Visual User Environment terminal window GL 23 GL 24 Workspace Manager The program that controls the size placement and operation of win dows on the HP VUE Workspace The Workspace Manager is a spe cial Window Manager See also Window Manager workstation A compact graphics oriented computer having high speed and high memory capacity A workstation usually includes a keyboard a moni tor and a system unit See also node disked workstation d
151. ts from Outside the ETSA PCIASSCMmbIY seere tie ce ok anal le eaea ees B 52 B 32 EISA GSC Slots from Inside the J282 EISA Assembly B 52 B 33 GSC PCI EISA Slots from inside the J2240 PCI Assembly ods soniose date he owt Wu aeea B 52 B 34 Removing the PCI EISA Assembly B 54 B 35 PCI EISA I O Assembly 0 0000 eee B 55 B 36 Rotating the PCI EISA Assembly FOL MSTA AU OM te 6 erent dole eA as eel oS aed a ea ome B 56 B 37 Removing the PCI EISA Assembly Cover B 57 B 38 Removing the PCI EISA Slot Cover B 58 B 39 Installing a PCI EISA or Graphics Board in the EISA ASSEDI acted ad inttente teas eae Stared hk ew ated B 59 B 40 Remove Block from PCI Assembly Cover B 60 B 41 Replacing PCI EISA Assembly Cover B 61 B 42 Rotating the PCI EISA Assembly Back B 62 B 43 Replacing PCI EISA Assembly B 63 C 1 Rear Panel SCSI Connectors with Terminators Attached C 27 C 2 Rear Panel SCSI Connectors without Terminators C 28 Tables 1 1 Audio Electrical Specifications 0 1 14 I penal OPIS dvi oe tew ote tue Pete ah ett at 1 16 2 1 CD ROM Drive Operating Controls and Features 2 4 3 1 LED Display Codes DDS DC Drive 3 4 3 2 LED Display Codes DDS 2 Drive 3 6 5 1 Problems Powering Up the System 5 3 5 2 Problems Loading and Bootin
152. type the following Main Menu Enter a command or a menu gt search ipl Enter The search command This causes your workstation to search exhaustively for bootable looks for bootable media meda on your workstation 3 Boot from one of the listed devices by typing the following at the prompt Main Menu Enter a command or a menu gt boot device where device 1s the hardware path to the device specified in mnemonic style notation such as FWSCSL 5 0 4 If your workstation still fails to boot there is either something wrong with the file system or with the hardware If you suspect a file system failure see the manual Using HP UX for help on dealing with file system failures If you think that something is wrong with the hardware continue reading this chapter for more troubleshooting information 5 10 Memory Failures J Class systems use Memory Page Deallocation a feature that allows the system to provide information to the operating system about memory failures HP UX 10 20 uses Memory Page Deallocation information to map out the failing memory areas and continue normal operation You can use the command memrpt with the detail switch to obtain informa tion about the Memory Page Deallocation Table PDT as well as single bit errors logged by the system usr sbin sysdiag DUT gt logtool LOGTOOL gt memrpt detail NOTICE You must be logged in as superuser to use the memrpt command To exit the sysdiag an
153. uctions which use Table C 10 1 Write in the type of internal drives currently connected to your system under the heading Fast Wide Differential SCSI Device Drives and each drive s SCSI device ID under the heading De vice ID Number 2 Add your new drive to the table 3 Check to see what SCSI device IDs are not used You may use ID numbers 0 through 6 and 8 through 15 if they are not already in use If the default ID on your drive does not conflict with any existing drive IDs use that ID If your default address conflicts with an existing drive ID assign a new fast wide differential SCSI device ID to your drive Refer to the drive s installation documentation for information on changing the device ID CAUTION Do not use SCSI device ID 7 for any device Table C 10 Fast Wide Differential SCSI Device IDs Device ID Address Number Fast Wide Differential SCSI Device Drives ID 7 not available Ist Internal Device 6 2nd Internal Device 5 NOTICE You can have no more than 15 SCSI devices connected to a FWD SCSI bus C 24 Ultra Wide SE SCSI IDs Before assigning a SCSI device ID to your drive you need to check your SCSI device IDs To check which SCSI device IDs are available and assign an ID to your device follow these instructions which use Table C 11 1 Write in the type of internal drives currently connected to your
154. umpers ID PWR ID2 ID1 IDO ID PWR ID2 ID1 IDO 0 c c000000 0 4 0 0 Blof o ooo 1 coco 0 0B 5 00 8o o SQ 2 000000 6 00 SEM 3 000 o Default Figure B 9 DDS DC Tape Drive SCSI Address Jumper Settings B 19 B 20 Bit 0 Bit1 Bit 2 Term PWR A O Co O oO J SCSI Connector Power a SCSI Term SCSI Term ID PWR Bit2 Biti Bit 0 ID PWR Bit2 Biti Bit 0 0 0000000 0 4 0 foo 0 o o 1 000000 5 0o E8e omy 2 o oo 0o80 0 6 o o EJE o 3 0000 Default Term PWR is not used in HP workstation configurations Figure B 10 DDS 2 Tape Drive and SCSI Address Jumper Settings SS WA o LSJ Operation Mode J Switches Lg olf J ON a ON Enp E jpg nnn 12345678 12345678 Compression Disabled Compression Enabled No Host Control No Host Control ON N ON T RRRARASE AAU RBARE 1234567 8 1234567 8 Compression Disabled Host Compression Enabled Can Control Compression With Host Control Default Setting Figure B 11 Switch Settings for Data Compression Operation Mode B 21 Floppy Drive
155. uses the HP UX operating system 10 20 or later HP UX 10 20 ACE Feb 1998 plus J2240 Hardware Extensions software for J2240 Instant Ignition systems systems with preloaded software have X windows and Hewlett Packard s graphical user in terface HP VUE version 3 0 or HP CDE installed and configured Please refer to the Instant Ignition System Configuration Informa tion sheet that shipped with your system for details on configuration If your Instant Ignition system does not have the kernel preconfigured with all of the device drivers you need refer to the manual System Administration Tasks HP 9000 Series 700 Computers to reconfigure your kernel If you have any questions about Instant gnition refer to Using Your HP Workstation for more information Important Before you begin using your workstation take a moment to gather the Information following important information and note it in the appropriate subsec You Need to tion for future use Note e LANIC ID Internet Protocol IP address Subnetwork mask NOTICE For help with these refer to Using your HP Workstation LANIC ID Locate the contents label that comes with the workstation shipping carton Find the LANIC ID listed there and record it here LANIC ID You can also get your LANIC ID by using the the lanscan command in a terminal window 1 20 IP Address and Subnetwork Mask Information Get the IP address and the subnet mask infor
156. ve is functioning prop erly If problems persist contact your system administrator or call your designated service representative Table 5 7 Problems Using the Floppy Disk Drive Problem Solution The floppy drive Re enter the commands and make sure does not respond to that you have typed them correctly commands Make sure that you specified the de vice file dev rfloppy c201d0s0 for commands that require a device file name Make sure that the write protect tab is set to write if you are trying to copy data to a floppy diskette Follow the instructions in the section entitled Running System Verification Tests later in this chapter to verify that the floppy drive is functioning properly If problems persist contact your system administrator or call your designated service representative 5 9 Dealing with a If your usual boot device typically a disk is not responding as it Boot Failure should you must try to boot from the disk or another boot device by selecting it manually To boot a device manually follow these steps 1 Follow the directions in Accessing the Boot Console Interface in Appendix D of this book NOTICE Your workstation automatically shuts down the operating system before it terminates the power 2 At the Main Menu prompt
157. ves Whenever the information differs we will specify whether the information refers to the DDS DC or the DDS 2 drive DDS Drive Your DDS tape drive is a 3 1 2 inch form factor DDS tape drive with data compression and a SCSI interface It conforms to the DDS for mat standard for storing computer data and incorporates a data com pression capability It s a high capacity high transfer rate device for data storage on tape Controls and Indicators Figure 3 1 shows the LEDs and eject button of the DDS drive Cassette LED Drive LED Eject Button Figure 3 1 DDS Drive Controls and Indicators 3 3 LEDs light emitting diodes indicate different activities or problems that occur with your workstation hardware LEDs DDS DC Drive This section describes the LED codes that are displayed The front panel has two colored LEDs the Cassette Light and the Drive Light A green light indicates normal operation and an amber light indicates a warning condition Pulsing shows activity between the drive and the SCSI bus If the Cassette Light left LED shows steady amber it means that the cassette 1s write protected If the Drive Light right LED shows steady amber this indicates a fault condition Table 3 1 lists the LED codes and their meanings Table 3 1 LED Display Codes DDS DC Drive
158. wake 3 12 Archiving Data in Compressed and Noncompressed Mode 3 14 Watne to a Data Cassette sies este ob Sew ehae beh 3 15 Restoring Files from a Data Cassette to Your System 3 15 Listing the Files on a Data Cassette 0 3 17 Further Command Information 005 3 18 Media Interchangeability Restrictions 3 18 Troubleshooune 4 2 sc2444 4 i6ae meee ea ieee cea aee ss 3 18 Ordering Information 0 0 0000 ee eee eee 3 19 Using Your 3 5 Inch Floppy Drive Using the Floppy Diskette sere cer siss cuceri eh eet hee ees 4 3 Setting the Write Protect Tab on a Diskette 4 3 Inserting and Removing a Diskette 4 4 Operating the Floppy Drive 0 cece eee ees 4 5 Verifying the Floppy Drive Configuration 4 5 Usine Device Piles is oid ih eso Ged ee a age Deed V 8 bse a eee 4 6 Formatting a New Diskette 0 0 0 ee eee eee 4 8 Transferring Data To and From a Floppy Diskette 4 8 Saving Files to a Floppy Diskette 4 9 Restoring Files from a Floppy Diskette to Your System 4 9 Listing the Files on a Floppy Diskette 4 10 For More Information 0 cece eee eee 4 10 Configuring the Floppy Driver 004 4 12 Troubleshooting 00 4 12 Ordering Intormatrom 2403 eva Seed CPAs Ghai le 4 4 12 Solving Problems Common Problem
159. wide SE SCSI definition limits the total cable length of SCSI cables to 3 meters 9 84 feet Always use the shortest possible cable s for your configuration If you are daisy chaining narrow single ended SCSI devices together use the following cables 92222A cable with 0 5 meter 1 6 feet length 92222B cable with 1 0 meter 3 2 feet length 92222C cable with 2 0 meter 6 6 feet length If you are daisy chaining fast wide differential SCSI devices togeth er use the following cables C2911A cable with 0 9 meter 3 feet length C2924A cable with 2 5 meter 8 2 feet length C2925A cable with 10 0 meter 32 8 feet length C2926A cable with 20 0 meter 65 6 feet length If you are daisy chaining ultra wide SE SCSI devices together use the following cables C2978A cable with 0 5 meter 1 64 feet length NOTICE See Determining SCSI Bus Length later in this Appendix to determine the total length of your cables Connectors and Terminator Any narrow single ended SCSI device connecting to the system box must use a 50 pin high density thumb screw connector on the end connecting to the system board and a 50 pin low density bail lock connector on the other end If you attach a second SCSI device the cable must have low density connectors on each end Any fast wide differential or ultra wide SE SCSI device connecting to the system box must use a 68 pin high density thumb screw co
160. wing CSTM gt exit If any tests failed further diagnosis is necessary by qualified service personnel Contact your designated service representative 5 17 Appendix A Safety and Regulatory Statements Declaration of conformity Emissions regulations Emissions regulations compliance Datacom users statement Acoustics Electrostatic discharge ESD precautions Laser safety statements Warnings and cautions This appendix contains safety and regulatory statements pertaining to your J282 2240 workstation A 2 DECLARATION OF CONFORMITY according to ISO TEC Guide 22 and EN45014 Manufacturer s Name Hewlett Packard Manufacturer s Addresses 100 Domain Drive Exeter N H 03833 USA declares that the product Product Name Computer Workstation Model Number HP 9000 J200 Series Base Product Number A4081A Product Options All conforms to the following Product Specifications Safety IEC 950 1992 A1 A2 EN 60950 1992 Al A2 EMC CISPR 22 1985 EN 55022 1988 Class B 1 EN 50082 1 1992 IEC 801 2 1991 prEN 55024 2 1992 3 kV CD 8kV AD IEC 801 3 1984 prEN 55024 3 1991 3 V m IEC 801 4 1988 prEN 55024 4 1992 1 kV Power Lines 0 5 kV Signal Lines Supplementary Information The product herewith complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC 1 The product was tested i
161. y Open 2 Gently pull the disc tray fully open 3 Grasp the disc by the edges and lift it out of the disc tray as shown in Figure 2 6 Be careful to touch only the edges of the disc A a Figure 2 6 Removing the CD ROM Disc From the Disc Tray The ioscan utility verifies the configuration of all drives 4 Gently push the disc tray in until it is closed as shown in Figure 2 7 Qo O a Figure 2 7 Disc Tray Closed Verifying the CD ROM Drive Operation To verify that your workstation can communicate with the CD ROM drive follow these steps 1 Click on the Terminal Control on the Front Panel of your Workspace 2 11 2 12 Terminal Control A terminal window opens Move the mouse cursor into the terminal window and click the left mouse button Enter the following at the prompt usr sbin ioscan d sdisk _Enter_ After a few moments the ioscan utility lists all of the SCSI I O devices it could find The list appears similar to the following Description I O Adapter GSC built in Fast Wide SCSI Interface QUANTUM LPS1O80WD DSP3210SW DEC DEC DSP3Z105W Core I O Adapter BPuLilt in oCo TOSHIBA CD ROM XM 4101TA SEAGATE ST3
162. your HP 9000 J282 2240 workstation This manual assumes that you have installed your workstation as described in the J Class Hardware Installation Guide xiv Audience Safety and Regulatory Statements Release Document s This guide is intended for HP 9000 J282 2240 workstation users See Appendix A in the back of this manual for safety and regulatory statements that apply to this workstation Please refer to the Release Document s you received with your sys tem or system software for additional information that we may not have been able to include in this guide at the time of its publication XV Revision History XVI If you are using HP UX version 10 20 refer to the following manuals for more information J Class Hardware Installation Guide A2876 90010 Using Your HP Workstation A2615 90003 Installing and Updating HP UX B2355 90050 System Administration Tasks HP 9000 Series 700 Computers B2355 9005 1 Configuring HP UX for Peripherals B2355 90053 HP Visual User Environment User s Guide B1171 90079 Managing Clusters of HP 9000 Computers Sharing the HP UX File System B2355 90038 To order manuals please contact your local sales office The revision history for each edition of the manual is listed below HP Part No A408 1 90601 A408 1 90607 A4476 90013 A2876 90013 A2876 90014 A2876 90015 Edition E0195 E0695 E0596
163. your first user process See also username login directory The directory in which you are placed when you log in usually your home directory See also home directory Login Manager The program that controls the initial startup of HP VUE and accepts the user s username and password login script The shell program that runs at each login and sets the login environ ment for your system menu bar An area at the top or bottom of a window that contain the titles of the pull down or pop up menus for that application minimize button In HP VUE a push button on the window frame that turns a screen into an icon See also icon iconize mouse pointer See pointer hame A character string associated with a file directory or link A name can include various alphanumeric characters but never a slash or null character See also pathname network Two or more workstations sharing information See also cluster workstation network controller A printed circuit board that passes bit streams between the network and the main memory of the workstation Coupled with the network transceiver the controller also handles signal processing encoding and network media access node A network computer workstation Each node in the network can use the data programs and devices of other network nodes Each node contains main memory and has its own disk or shares one with anoth er node See also disked workstation

HP 2240 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents