Hotpoint HHC6.7AM(BK) User's Manual
Contents
1. The grease filter retains the particles of grease produced during cooking it must be cleaned at least once a month with a non aggressive detergent either by hand or with a low temperature short dishwasher cycle To extract the grease filter pull the spring loaded handle If washed in a dishwasher the metal filter may change colour but this does not affect its performance Servicing the charcoal filter B 3 The charcoal filter retains PS unpleasant cooking odours The filter saturates after a variable time depending on the type of cooking and hovv often the grease filter is cleaned The cartridge must be replaced at least once every twenty months This filter can NOT be washed or regenerated Disassembly Rotate the filter 90 to remove it from the suction assembly Assembly Fit the active carbon filter into the suction assembly and rotate it 90 to secure it in place Replacing the bulbs Disconnect the unit from the mains and remove the grease filter Caution Make sure the bulbs are cool before touching them 1 Extract the guard by prising it out with a small flat head screwdriver or something similar 2 Replace the faulty bulb Use only bulbs of the same type for details see the technical data in the following manual 3 Refit the guard push it in 11 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 Replacing2. air being exhausted may not be exhausted into a wall cavity unless the cavity in question is specifically intended for this purpose Equip the room with air intakes to prevent the hood creating suction pressure in the interior this must not exceed 0 04 mbar The manufacturer is not liable for any consequences of failure to observe these instructions Filter or ducted Your hood is supplied as a ducted unit If you wish to use it as a filter unit you must install the proper ACCESSORY KIT Note If supplied with the hood the accessory active charcoal filter unit may already be installed Instructions for transforming the hood from the ducted to the filter version are given in this manual see Filter version Hotpoint Ducted version The hood purifies the air and expels it outdoors via an exhaust duct dia 150mm connected to its outlet flange The diameter of the exhaust tube must be equal to that of the outlet flange Caution The exhaust duct is not supplied and must be purchased separately When routed horizontally the tube must be angled slightly upwards around 10 to enable the air to be conveyed outdoors more easily If the hood is fitted with charcoal filters they must first be removed Filter version The hood purifies the air and returns it to the room This version of the hood requires installation of an accessory active charcoal filter unit This version requires an air d
3. time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to you This guarantee is subject to the following conditions The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The appliance has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of any consumable item or accessory These included but not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 5 Year Parts Guarantee Hotpoint also offers you a free 5 year parts guarantee This a
4. HHP7 5CM HHP6 5CM HHP9 5CM HHC6 7AM WH HHC6 7AM BK cB English Operating Instructions COOKER HOOD Contents Operating Instructions 1 Warnings 7 Installation 9 PYRAMID controls 10 Maintenance and care 11 Troubleshooting 12 After Sales Service 14 Guarantee 15 Hotpoint LO 9 i S gt After Sales Service o 150 125mm 0150 IM IT gt 65 cm min 55 cm min 4 120mm 10120 A 150mm 4 4 150mm VVarnings Keep this manual for reference If you sell transfer or move the unit to another location make sure to keep the manual with the product Read the instructions carefully they conta
5. ately The first sequence resets the grease filter while the second sequence resets the odour filter Configuring the hood To set the operating mode of the hood hold down 4 for 6 seconds After a long beep the type of installation displays Ducted square at bottom left flashing Filter square at bottom right flashing You can change the type of installation by pressing T4 To quit configuration mode press T1 once this switches the unit off and saves the last displayed setting Maintenance and care Caution Before cleaning or servicing the unit disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker First cleaning e Remove the protective film e Clean with a damp sponge and a little neutral soap e Rinse off with a damp cloth Dry with a soft cloth if the hood is stainless steel dry along the metal s grain Hotpoint Periodic cleaning The hood must be cleaned frequently at least as often as you service the grease filter inside and out Use a damp cloth and a neutral liquid detergent with lukewarm water Do not use abrasive or corrosive products Warning Failure to observe the hood cleaning and filter cleaning replacement instructions can result in fires Follow the instructions carefully The manufacturer is not liable for any damage to the motor or fires caused by incorrect care or failure to follow the above instructions Servicing the grease filter A
6. dditional guarantee is conditional on you registering your appliance vvith us and the parts being fitted by one of our authorised engineers There vvill be a charge for our engineer s time To activate the extra parts warranty on your appliance simply call our registration line on 08448 24 24 24 Republic of Ireland 01 230 0800 Extended Guarantees VVe offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08448 226 226 Republic of Ireland 01 230 0233 Free Helpdesk Service VVe have a dedicated team vvho can provide free advice and assistance vvith your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Hotpoint Service Hotline on 08448 224 224 Republic of Ireland 0818 313 413 for telephone assistance or where necessary to arrange for an engineer to call PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 15 195107497 02 0312013 XEROX FABRIANO PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 16
7. eflector a reduction adapter and the charcoal filter s The top tube must have its air outlet slots uppermost Technical data dia of Model pole Teri exhaust tube cm PYRAMID 60cm 61 82 59 8 50 15 12 PYRAMID 70cm 61 82 69 8 50 15 12 PYRAMID 90cm 61 82 89 9 50 15 12 Model code Bulb V Bulb draw W Total draw W HHP7 5CM Halogen 2x25 160 Model code Bulb V Bulb draw W Total draw W HHP6 5CM HHC6 7AM WH Halogen 2x25 160 HHC6 7AM BK Model code Bulb V Bulb draw W Total draw W HHP9 5CM Halogen 2x25 160 Power Voltage Cap Dimensions Halogen 25 W 2x25W 230 V G9 L40x 14 Halogen 20 W 2x20W 12V G4 L30x 10 LED JRisk Group 1 according to Standard EN 62471 The hoods are conforming to the following EC Directives e Low voltage Directive 2006 95 EC 12 12 2006 Directive 2004 108 EC 15 12 2004 i Only available in certain models 9 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 PYRAMID controls Models with mechanical keypad HHP7 5CM HHP6 5CM HHP9 5CM HHC6 7AM WH HHC6 7AM BK 0 0 42 Y 0 T1 Motor reset Pressing the button while the hood is in operation turns it OFF T2 Speed 1 Pressing the button sets the hood to speed 1 T3 Speed 2 Pressing the button sets the hood to speed 2 T4 Speed 3 Pressing the b
8. f to set speed 1 Pressing the button while the hood is in operation turns it OFF T2 Speed Pressing the button returns the hood to the previous speed T3 Speed Pressing the button returns the hood to the next speed If the hood is off pressing these buttons sets speed 1 T4 Booster Pressing this button sets the hood to high speed the letter b flashes slowly on the display After 5 minutes the hood returns to its previous speed this can also be done while booster mode is on by pressing either speed button T2 or T3 T5 Timer Pressing this button delays the hood turning off automatically by 5 minutes The timer counts down on the display in minutes The timer can only be set for manual speeds not for booster mode T6 Lights ON OFF PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 Greaselodour filter vvarnings The bar at the top left flashes to indicate that the grease filter is saturated The bar at the top right flashes to indicate that the odour filter is saturated If both bars are flashing then both filters are saturated You must then clean replace the grease filter A or odour filter B or both accordingly see Maintenance and care The latter only applies to the filter version To reset the filter counter Hold down 4 for three seconds while the hood is on If both filter warnings are active at the same time you must reset each separ
9. he installation must be done by a qualified technician Electrical hook up The mains voltage must match that given on the ratings label inside the hood itself If the hood has a power plug connect the hood to an easily accessible regulatory power socket If it does not direct connection to the mains or the socket is not easily accessible install a two pole regulatory switch to enable total disconnection from the mains in case of category Ill overvoltage as required by the installation regulations Caution Always check that the mains cable is hooked up properly and check that it operates correctly before reconnecting the hood to the mains Air exhaust for ducted units Connect the hood to duct and wall exhaust hole of a diameter equal to that of the air outlet flange Using a smaller diameter tube and exhaust hole reduces the extraction capacity of the hood and also increases its running noise The manufacturer is not liable for any consequences of doing so Use the shortest duct required to achieve the purpose Use a duct with as few bends as possible Avoid suddenly changing the diameter of the duct The duct must have as smooth an inner surface as possible The duct must be made of regulatory material Do not connect the hood to flues carrying combustion fumes from other equipment boilers chimneys stoves etc Observe the instructions of the competent authorities in relation to the air exhaust The
10. in important installation user and safety information Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts General safety information e The distance between the cookware support surface on top of the cooking appliance and the lowest part of the cooker hood must be at least 65 cm if the hood is installed over a gas cooktop 55 cm if the hood is installed over an electric cooktop If the installation instruction manual for the gas cooking appliance specifies a greater distance this measurement should be taken into account e cooker hood comes with anchor plugs which are suitable for use with most walls ceilings However you must contact a qualified technician to check the suitability of the materials in relation to the type of wall ceiling which must be strong enough to support the weight of the unit Caution Do not hook the unit up to its electrical power supply until the installation has been completed Before cleaning or servicing the unit disconnect it from the mains by pulling the povver plug or disconnecting the main circuit breaker Always wear work gloves when installing and servicing the unit It is not intended for use by children or persons with sensory or mental disability and lack of experience or familiarity except under the supervision or instruction of a person responsible for their safety Make sure children do not play with the unit Ne
11. ppliance to keep it looking good and functioning efficiently throughout its life UK 08448 225 225 Republic of Ireland 0818 313 413 www hotpointservice co uk Appliance Registration We want to give you additional benefits of Hotpoint ownership To activate your free 5 year parts guarantee you must register your appliance with us UK 08448 24 24 24 Republic of Ireland 01 230 0800 www hotpointservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 Recycling and Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into mains socket and the door cannot be locked shut PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 14 Hotpoint Guarantee 12 months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that
12. roduced the kitchen is adequately ventilated for the unit to take air in the charcoal filter is not exhausted filter version If the hood turns off during normal operation Check that the unit is powered up the circuit breaker has not tripped In case of faulty operation before contacting Technical service first disconnect the machine from the mains for at least 5 seconds by pulling its plug then reconnect it If the fault persist contact Technical Service i Only available in certain models PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 12 Hotpoint Be PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 13 After Sales Service No one is better placed to care for your Hotpoint appliance during the course ofits vvorking life than us the manufacturer Essential Contact Information Hotpoint Service We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast reliable local service UK 08448 224 224 Republic of Ireland 0818 313 413 www hotpointservice co uk Please note Our advisors will require the following information Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your a
13. the lights LED The hood is fitted with a lighting system based on LED technology The LEDs ensure optimal lighting longer life and lower consumption compared with traditional lights To replace them please contact the assistance service Electrical cable If the power cable is damaged it can be replaced by the manufacturer or his technical service to prevent any attendant risks SCRAPPING The unit is marked for conformity with European Directive 2012 19 EC Waste Electrical and Electronic Equipment WEEE By ensuring that the unit is scrapped properly the user contributes to safeguarding the environment and public health The symbol on the product or on its accompanying documents indicates that the product may not be treated as domestic waste but must be handed over to a sorting centre for electrical and electronic waste Dispose of it in accordance with local waste disposal regulations For further information on the handling recovery and recycling of this product contact the local authority domestic waste disposal service or the reseller from whom you purchased it Troubleshooting If something does not work make the following simple checks before contacting Technical Service If the hood does not operate Check that the unit is powered up a speed has been set If the hood is not working effectively Check that e the selected motor speed is sufficient to handle the amount of smoke and steam being p
14. utton sets the hood to speed 3 T5 Lights ON OFF Models with soft button keypad Only available in certain models 00980 T1 Motor reset Pressing the button while the hood is in operation turns it OFF T2 Speed 1 Pressing the button sets the hood to speed 1 T3 Speed 2 Pressing the button sets the hood to speed 2 T4 Speed 3 Pressing the button sets the hood to speed 3 T5 Booster Pressing the button sets the hood to high speed After 5 minutes the hood returns to the previous speed pressing a speed button T2 T3 or T4 quits booster mode and sets the selected speed T6 Lights ON OFF 10 Grease odour filter warnings The T2 icon flashes to indicate that the grease filter is saturated while T3 flashes to indicate that the odour filter is saturated and if both are flashing then both filters are saturated You must then clean replace the grease filter A or odour filter B or both accordingly see Maintenance and care To reset the filter counter Hold down T4 for three seconds while the hood is on The warning led flashes three times then returns to its normal mode If both filter warnings are active at the same time you must reset each separately The first sequence resets the grease filter while the second sequence resets the odour filter Models with soft button keypad and display Only available in certain models ON ONA 1 Motor ON OFF Press the button with the hood of
15. ver operate the unit without its grease filter installed NEVER use the hood as a support unless expressly instructed to do so The room must be adequately ventilated if the hood is used at the same time with other equipment burning gas or other fuels Extracted air must not be conveyed into a duct used for exhausting combustion fumes from gas or other fuel fired equipment Observe all regulations in relation to air extraction NEVER cook food with an open flame under the hood open flames will damage the filters and may cause fires Never do this e Always supervise frying to make sure the heated oil does not catch fire e Strictly observe all local regulations in relation to the technical and safety measures to be employed in fumes extraction Clean the product frequently inside and out AT LEAST ONCE A MONTH and in observance of the maintenance instruction given in this manual Failure to observe the hood cleaning and filter cleaning replacement instructions can result in fires Never use the hood without its bulbs properly installed electrocution hazard The manufacturer is not liable for any inconvenience damage or fire caused by the unit as a result of failure to observe the instructions given in this manual Caution The unit s accessible parts can get very hot when used with cooking equipment Installation The installation procedure is illustrated in the first pages of this manual T
Download Pdf Manuals
Related Search